Quad MECL Translator MC10124 quad translator interfacing data con

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Quad MECL Translator MC10124 quad translator interfacing data con

Datasheet Thumbnail

Top Searches for this datasheet

Quad MECL Translator
MC10124 quad translator interfacing data control signals between saturated logic section MECL section digital systems. MC10124 compatible inputs, MECL complementary open-emitter outputs that allow inverting/ non-inverting translator differential line driver. When common strobe input logic level, forces true outputs MECL logic state inverting outputs MECL high logic state. Power supply requirements ground, +5.0 Volts, -5.2 Volts. Propagation delay MC10124 typically levels standard Schottky MECL 10,000 out. advantage this device that level information transmitted differentially, balanced twisted pair lines, MECL equipment, where signal received MC10115 MC10116 differential line receivers. MC10124 useful computers, instrumentation, peripheral controllers, test equipment, digital communications systems. typ/pkg Load) out) (20%-80%)
MC10124
SUFFIX CERAMIC PACKAGE CASE 620-10 SUFFIX PLASTIC PACKAGE CASE 648-08 SUFFIX PLCC CASE 775-02
ASSIGNMENT
BOUT AOUT COUT DOUT DOUT COUT
LOGIC DIAGRAM
BOUT AOUT COMMON STROBE
assignment Dual-in-Line Package. PLCC assignment, Conversion Tables page 6-11 Motorola MECL Data Book (DL122/D).
(+5.0Vdc) (-5.2Vdc)
3/93
Motorola, Inc. 1996
3-82
MC10124
ELECTRICAL CHARACTERISTICS
Test Limits Under Test -1.060 -1.060 -1.890 -1.890 -1.080 -1.080 -1.655 -1.655 -1.5 -1.5 -0.890 -0.890 -1.675 -1.675 -0.960 -0.960 -1.850 -1.850 -0.980 -0.980 -1.630 -1.630 -30°C -12.8 -3.2 -1.5 -1.5 -0.810 -0.810 -1.650 -1.650 -0.890 -0.890 -1.825 -1.825 -0.910 -0.910 -1.595 -1.595 +25°C -12.8 -3.2 -1.5 -1.5 -0.700 -0.700 -1.615 -1.615 +85°C -12.8 -3.2 Unit mAdc mAdc mAdc µAdc mAdc t6+1+ t6-1- t7+1+ t7-1- t7+3- t7-3+
Characteristic Negative Power Supply Drain Current Positive Power Supply Drain Current Reverse Current Forward Current Input Breakdown Voltage Clamp Input Voltage High Output Voltage Output Voltage High Threshold Voltage Threshold Voltage Switching Times Load)
Symbol ICCH ICCL BVin VOHA VOLA
Propagation Delay (+3.5Vdc 50%)1
Rise Time Fall Time
80%) 80%)
switching time test circuit. Propagation delay this circuit specified from +1.5Vdc point output waveform. +3.5Vdc shown here because logic supply levels shifted volts positive.
MECL Data DL122
3-83
MC10124
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts) Test Temperature -30°C +25°C +85°C Under Test +6.0 t6+1+ t6-1- t7+1+ t7-1- t7+3- t7-3+ Pulse Pulse 5,7,10,11 5,7,10,11 5,6,7,10,11 +4.0 +4.0 +4.0 VILmax +0.40 +0.40 +0.40 VIHA' +2.00 +1.80 +1.80 VILA' +1.10 +1.10 +0.90 +0.40 +0.40 +0.40
TEST VOLTAGE APPLIED PINS LISTED BELOW VILmax VIHA' VILA'
5,6,7,10,11,16
Characteristic Negative Power Supply Drain Current Positive Power Supply Drain Current Reverse Current Forward Current Input Breakdown Voltage Clamp Input Voltage High Output Voltage Output Voltage High Threshold Voltage Threshold Voltage Switching Times Load)
Symbol ICCH ICCL BVin VOHA VOLA
5,7,10,11,16 6,16 +2.0
Propagation Delay (+3.5Vdc 50%)1
Rise Time
80%)
Fall Time 80%) switching time test circuit. Propagation delay this circuit specified from +1.5Vdc point output waveform. +3.5Vdc shown here because logic supply levels shifted volts positive.
3-84
MECL Data DL122
MC10124
ELECTRICAL CHARACTERISTICS (continued)
TEST VOLTAGE VALUES (Volts) Test Temperature -30°C +25°C +85°C Under Test +2.40 +2.40 +2.40 +5.00 +5.00 +5.00 -5.2 -5.2 -5.2 (mA) +1.0 +1.0 +1.0
TEST VOLTAGE APPLIED PINS LISTED BELOW +7.0 -3.2
5,6,7,10,11,16
Characteristic Negative Power Supply Drain Current Positive Power Supply Drain Current Reverse Current Forward Current Input Breakdown Voltage Clamp Input Voltage High Output Voltage Output Voltage High Threshold Voltage Threshold Voltage Switching Times Load)
Symbol ICCH ICCL BVin VOHA VOLA
5,7,10,11,16 6,16 +2.0
Propagation Delay (+3.5Vdc 50%)1
t6+1+ t6-1- t7+1+ t7-1- t7+3- t7-3+
Rise Time
80%)
Fall Time 80%) switching time test circuit. Propagation delay this circuit specified from +1.5Vdc point output waveform. +3.5Vdc shown here because logic supply levels shifted volts positive. Each MECL 10,000 series circuit been designed meet specifications shown test table, after thermal equilibrium been established. circuit test socket mounted printed circuit board transverse flow greater than linear maintained. Outputs terminated through 50-ohm resistor -2.0 volts. Test procedures shown only gate. other gates tested same manner.
MECL Data DL122
3-85
MC10124
SWITCHING TIME TEST CIRCUIT
+6.0
+7.0
Vout NAND
Vout
Coax
Coax
Coax
Input Pulse Generator
Unused outputs connected 50-ohm resistor ground.
Input Pulse ±0.5 90%)
50-ohm termination ground cated each scope channel input. input output cables scope equal lengths 50-ohm coaxial cable. Wire length should inch from TPin input TPout output pin.
-3.2
NOTE: power supply logic levels shown shifted volts positive.
3-86
MECL Data DL122
MC10124
OUTLINE DIMENSIONS
SUFFIX PLASTIC PLCC PACKAGE CASE 775-02 ISSUE
0.007 (0.180)
0.007 (0.180)
VIEW
0.010 (0.250)
0.007 (0.180) 0.007 (0.180)
0.007 (0.180)
0.004 (0.100) 0.010 (0.250)
SEATING PLANE
VIEW 0.007 (0.180)
VIEW
NOTES: DATUMS -L-, -M-, DETERMINED WHERE LEAD SHOULDER EXITS PLASTIC BODY MOLD PARTING LINE. DIMENSION TRUE POSITION MEASURED DATUM -T-, SEATING PLANE. DIMENSIONS INCLUDE MOLD FLASH. ALLOWABLE MOLD FLASH 0.010 (0.250) SIDE. DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. PACKAGE SMALLER THAN PACKAGE BOTTOM 0.012 (0.300). DIMENSIONS DETERMINED OUTERMOST EXTREMES PLASTIC BODY EXCLUSIVE MOLD FLASH, BURRS, GATE BURRS INTERLEAD FLASH, INCLUDING MISMATCH BETWEEN BOTTOM PLASTIC BODY. DIMENSION DOES INCLUDE DAMBAR PROTRUSION INTRUSION. DAMBAR PROTRUSION(S) SHALL CAUSE DIMENSION GREATER THAN 0.037 (0.940). DAMBAR INTRUSION(S) SHALL CAUSE DIMENSION SMALLER THAN 0.025 (0.635).
INCHES 0.385 0.395 0.385 0.395 0.165 0.180 0.090 0.110 0.013 0.019 0.050 0.026 0.032 0.020 0.025 0.350 0.356 0.350 0.356 0.042 0.048 0.042 0.048 0.042 0.056 0.020 0.310 0.330 0.040
MILLIMETERS 9.78 10.03 9.78 10.03 4.20 4.57 2.29 2.79 0.33 0.48 1.27 0.66 0.81 0.51 0.64 8.89 9.04 8.89 9.04 1.07 1.21 1.07 1.21 1.07 1.42 0.50 7.88 8.38 1.02
MECL Data DL122
3-87
MC10124
OUTLINE DIMENSIONS
SUFFIX CERAMIC PACKAGE CASE 620-10 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEAD WHEN FORMED PARALLEL. DIMENSION NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. INCHES 0.750 0.785 0.240 0.295 0.200 0.015 0.020 0.050 0.055 0.065 0.100 0.008 0.015 0.125 0.170 0.300 0.020 0.040 MILLIMETERS 19.05 19.93 6.10 7.49 5.08 0.39 0.50 1.27 1.40 1.65 2.54 0.21 0.38 3.18 4.31 7.62 0.51 1.01
SEATING PLANE
0.25 (0.010)
0.25 (0.010)
SUFFIX PLASTIC PACKAGE CASE 648-08 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.740 0.770 0.250 0.270 0.145 0.175 0.015 0.021 0.040 0.70 0.100 0.050 0.008 0.015 0.110 0.130 0.295 0.305 0.020 0.040 MILLIMETERS 18.80 19.55 6.35 6.85 3.69 4.44 0.39 0.53 1.02 1.77 2.54 1.27 0.21 0.38 2.80 3.30 7.50 7.74 0.51 1.01
SEATING PLANE
0.25 (0.010)
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters which provided Motorola data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer. reach USA/EUROPE/Locations Listed: Motorola Literature Distribution; P.O. 5405, Denver, Colorado 80217. 303-675-2140 1-800-441-2447 MfaxTM: RMFAX0@email.sps.mot.com TOUCHTONE 602-244-6609 INTERNET: http://Design-NET.com
JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Ping Industrial Park, Ting Road, N.T., Hong Kong. 852-26629298
MOTOROLA 3-88
*MC10124/D*
MC10124/D MECL Data DL122

Quad MECL Translator MC10124 quad translator interfacing data con

Top Searches for this datasheet

Other recent searches