INCH IMAGE SENSOR CAMERA KC73125UBA interline transfer area image
|
|
|
Top Searches for this datasheet
KC73125UBA
INCH IMAGE SENSOR CAMERA
KC73125UBA interline transfer area image sensor developed inch optical format video cameras, surveillance cameras, object detectors image pattern recognizers. High sensitivity achieved through on-chip micro lenses (Hole Accumulated Diode) photosensors. This chip features field integration read system electronic shutter with variable charge storage time.
16Pin
FEATURES
High Sensitivity Optical Size inch Format Variable Speed Electronic Shutter (1/60, 1/100 1/10,000sec) Dark Current Horizontal Register Drive 16pin Ceramic Package Field Integration Read System Bias Reset Gate
ORDERING INFORMATION
Device KC73125UBA Package 16Pin Operating
STRUCTURE
Number Total Pixels: Number Effective Pixels: Chip Size: Unit Pixel Size: Optical Blacks Dummies: 537(H) 505(V) 510(H) 492(V) 6.00mm(H) 4.95mm(V) 9.60µm(H) 7.50µm(V) Refer Figure Below Vertical Line (Even Field Only)
Dummy Pixels Optical Black Pixels
Effective Imaging Area
OUTPUT
V-CCD
Effective Pixels
H-CCD
INCH IMAGE SENSOR CAMERA
KC73125UBA
BLOCK DIAGRAM
(Top View)
VOUT
Vertical Shift Register
Vertical Shift Register
Vertical Shift Register
Horizontal Shift Register
Vertical Shift Register
Figure Block Diagram
DESCRIPTION
Table Description Symbol VOUT Description Vertical transfer clock Vertical transfer clock Vertical transfer clock Vertical transfer clock Ground Output stage gate bias Output stage source bias Signal output Symbol Description Output stage drain bias Ground Substrate bias Protection circuit bias Charge reset clock connection Horizontal transfer clock Horizontal transfer clock
KC73125UBA
INCH IMAGE SENSOR CAMERA
ABSOLUTE MAXIMUM RATINGS (NOTE)
Table Absolute Maximum Ratings Characteristics Substrate voltage Supply voltage VDD, VOUT, VDD, VOUT, Vertical clock input voltage V1,V2, Horizontal clock input voltage Voltage difference between vertical horizontal clock input pins Symbols Min. -0.3 -0.3 -0.3 -0.3 Max. Output clock input voltage Protection circuit bias voltage Operating temperature Storage temperature TSTG -0.3 Unit
NOTE: device destroyed, applied voltage temperature higher than absolute maximum rating voltage temperature.
INCH IMAGE SENSOR CAMERA
KC73125UBA
CHARACTERISTICS
Table Characteristics Item Output stage drain bias Output stage gate voltage Output stage source voltage Substrate voltage adjustment range Fluctuation voltage range after substrate voltage adjusted Protection circuit bias voltage Output stage drain current Symbol VSUB VSUB Min. 14.55 1.75 Typ. 15.0 Max. 15.45 2.25 Unit Remark
Ground through 14.5
lowest vertical clock level
CLOCK VOLTAGE CONDITIONS
Table Clock Voltage Conditions Item Read-out clock voltage Vertical transfer clock voltage Symbol VVH1, VVH3 VVM1 VVL1 Horizontal transfer clock voltage VHH1, VHH2 VHL1, VHL2 Charge reset clock voltage VRSH VRSL Substrate clock voltage VSUB Min. 14.55 -0.2 -9.5 4.75 -0.2 4.75 -0.2 Typ. 15.0 -9.0 23.0 Max. 15.45 -8.5 5.25 5.25 Unit Remark High level Middle High High Shutter
KC73125UBA
INCH IMAGE SENSOR CAMERA
DRIVE CLOCK WAVEFORM CONDITIONS
Read Clock Waveform
100%
VVH3
Vertical Transfer Clock Waveform
VVH1
VVHH VVHL
VVHH VVHL
=1~4)
INCH IMAGE SENSOR CAMERA
KC73125UBA
Horizontal Transfer Clock Waveform Diagram
Reset Gate Clock Waveform Diagram
Point waveform VRGLH VRGLL VRGL 0.5V VRGL
waveform
VRGLH maximum value VRGLL minimum value coupling waveform period from Point diagram about rise VRGL (VRGLH VRGLL)/2, VFRG VRGH VRGL
Substrate Clock Waveform
100%
KC73125UBA
INCH IMAGE SENSOR CAMERA
CLOCK EQUIVALENT CIRCUIT CONSTANT
Table Clock Equivalent Circuit Constant
Item Read-out clock Vertical clock Symbol Min. Horizontal clock Reset clock Substrate clock Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
INCH IMAGE SENSOR CAMERA
KC73125UBA
EQUIVALENT CIRCUIT PARAMETERS
Table Equivalent Circuit Parameters Item Capacitance between vertical transfer clock Symbol Capacitance between vertical transfer clocks CV12, CV34 CV23, CV41 CV13 CV24 Capacitance between horizontal transfer clock Capacitance between horizontal transfer clocks Capacitance between substrate clock Vertical transfer clock serial resistor Vertical transfer clock ground resistor Horizontal transfer clock serial resistor Reset gate clock serial resistor CH1, CH12 CSUB RVGND RH1, Typ. 1,300 1,300 1120 Unit Remark
KC73125UBA
INCH IMAGE SENSOR CAMERA
OPERATING CHARACTERISTICS
Device Temperature Table Operating Characteristics Item Sensitivity Saturation signal Smear Blooming margin Uniformity Dark signal (NOTE) Dark shading (NOTE) Image Flicker
NOTE: Test Temperature
Symbol YSAT YLAG
Min.
Typ.
Max.
Unit mV/lux
Remark
0.007 1,000
0.015
times
TEST CONDITION
light source with color temperature 3,200K hallogen lamp CM-500S filter. light source adjusted accordance with average value signals indicated each item. Through following tests substrate voltage should value while device condition should kept within range bias clock conditions.
INCH IMAGE SENSOR CAMERA
KC73125UBA
TEST METHODS
Measure light intensities when averaged illuminance output value standard illuminance output value, 150mV (YA) when half 150mV (1/2 YA).
Adjust light intensity times value with which then measure averaged illuminance output value YSAT).
Adjust light intensity times value with which then remove read-out clock drain signal photosensors electronic shutter operation respective horizontal blanking times with other clocks unchanged. Measure maximum illuminance output value (YSM).
Adjust light intensity 1,000 times value with which then inspect whether there blooming phenomenon not.
Measure maximum minimum illuminance output value (YMAX, YMIN) when light intensity adjusted make
Measure with horizontal idling time transfer level reference, when device ambient temperature light sources shielded.
Follow test method measure maximum (DMAX) minimum illuminance output (DMIN).
KC73125UBA
INCH IMAGE SENSOR CAMERA
Adjust light intensity signal output value strobe light 150mV (YA), calculate below formula with measuring image signal which qenerated below timing diagram.
Light Strobe Timing Signal Output 150mV
YLag
Output
Adjust light intensity signal average value 150mV (YA), calculate below formula with measuring signal differences [mV]) between fields.
INCH IMAGE SENSOR CAMERA
KC73125UBA
SPECTRAL RESPONSE CHARACTERISTICS
Excluding Light Source Characteristics
Spectral Response Wave Length (nm)
Figure Spectral Response Characteristics
KC73125UBA
INCH IMAGE SENSOR CAMERA
APPLICATION CIRCUITS
XSUB
KS7221D
100K
MA110
47µ/16V 180K
KC73125UBA
10µ/25V
1µ/10V
VOUT
KSC2757 3.9K
1µ/50V
10µ/25V
10µ/25V
Output
Figure Application Circuits
INCH IMAGE SENSOR CAMERA
KC73125UBA
READ-OUT CLOCK TIMING CHART
Unit: [µs]
Field
38.1
Even Field
Figure Read-out Clock Timing Chart
KC73125UBA
INCH IMAGE SENSOR CAMERA
CLOCK TIMING CHART (VERTICAL SYNC.)
2468 1357
CLP1
Figure Clock Timing Chart (Vertical Sync.)
INCH IMAGE SENSOR CAMERA
KC73125UBA
CLOCK TIMING CHART (HORIZONTAL SYNC.)
XSHD
XSHP
CLP1
Figure Clock Timing Chart (Horizontal Sync.)
KC73125UBA
INCH IMAGE SENSOR CAMERA
PACKAGE DIMENSIONS
Unit:
2.50 2-R0.50
Package Material Lead Material
Ceramic Alloy
Figure Package Dimensions
INCH IMAGE SENSOR CAMERA
KC73125UBA
HANDLING INSTRUCTIONS
Static Charge Prevention image sensors easily damaged static discharge. Before handling, sure take following protective measures. chargeable gloves, clothes material. Also conductive shoes. When handling directly, earth band. Install conductive floor working table prevent generation static electricity. Ionized recommended discharging when handling image sensor. shipment mounted substrates, boxes treated prevention static charges. Soldering Make sure package temperature does exceed Solder dipping mounting furnace causes damage glass other defects. grounded soldering iron solder each less than seconds. repairs remount, cool sufficiently. dismount imaging device, solder suction equipment. When using electronic disoldering tool, thermal controller zero cross on/off type connect ground. Dust Dirt Protection Operate clean environments (around class 1000 will appropriate). either touch glass plates hand have object come contact with glass surface. Should dirt stick glass surface blow with blow(for dirt stuck through static electricity ionized recommended). Clean with cotton ethyl alcohol glass surface grease stained. caerful scratch glass. Keep case protect from dust dirt. prevent condensation, preheat precool when moving room with great temperature differences. When protective tape applied before shipping, just before remove tape applied electrostatic protection. reuse tape. expose strong light (sun rays) long period, color filter discolored.
Exposure high temperature humidity will affect characteristics. accordingly avoid storage usage such conditions.
image sensors precise optical equipment that should subject mechanical shocks.
Other recent searches
XZMG56W - XZMG56W XZMG56W Datasheet
VBFZ-6260+ - VBFZ-6260+ VBFZ-6260+ Datasheet
TLP250 - TLP250 TLP250 Datasheet
TLP251 - TLP251 TLP251 Datasheet
TLP250F - TLP250F TLP250F Datasheet
TLP251F - TLP251F TLP251F Datasheet
VDE0884 - VDE0884 VDE0884 Datasheet
HCS373 - HCS373 HCS373 Datasheet
DDR400 - DDR400 DDR400 Datasheet
DDR333 - DDR333 DDR333 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
