Product specification Supersedes data 1999 1999 Product specifica

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Product specification Supersedes data 1999 1999 Product specifica

Datasheet Thumbnail

Top Searches for this datasheet

GTL2004 Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
Product specification Supersedes data 1999 1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
FEATURES
Operates quad GTL/GTL+ sampling receiver Quad bidirectional interface Separate latch enable each Live insertion/extraction permitted outputs include series resistance Latch-up protection exceeds 500mA JEDEC protection exceeds 2000V JEDEC
DESCRIPTION
GTL2004 quad translating transceiver designed 3.3V system interface with GTL/GTL+ bus. direction allows part function either sampling receiver interface. Separate latch enables allow sampling holding data from bus. LVTTL/TTL GTL/GTL+ driver
CONFIGURATION
GTLREF
SW00318
DESCRIPTION
NUMBER SYMBOL GTLREF NAME FUNCTION Direction control input Data inputs/outputs side, GTL) Data inputs/outputs side, TTL) Latch enables reference voltage Ground (0V) Positive supply voltage
QUICK REFERENCE DATA
SYMBOL tPLH tPHL CI/O PARAMETER Propagation delay Input capacitance DIR, capacitance CONDITIONS Tamb 25°C 50pF; 3.3V Outputs disabled; VI/O 3.152V TYPICAL UNIT
ORDERING INFORMATION
PACKAGES 16-Pin Plastic TSSOP Type TEMPERATURE RANGE -40°C +85°C ORDER CODE GTL2004 NUMBER SOT403-1
1999
853-2165 21984
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
LOGIC SYMBOL
FUNCTION TABLE
INPUT Inputs INPUT/OUTPUT Inputs
LATCH
HIGH voltage level voltage level Don't care change
LATCH
LATCH
LATCH
GTLREF
SW00319
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
ABSOLUTE MAXIMUM RATINGS1
accordance with Absolute Maximum System (IEC 134); voltages referenced (ground SYMBOL Tstg PARAMETER supply voltage input diode current input voltage3 output diode current output voltage3 Current into output state Current into output HIGH state Storage temperature range port port Output HIGH state; port Output HIGH state; port port port port TEST CONDITIONS RATING -0.5 +4.6 -0.5 +7.0 -0.5 +4.6 -0.5 +7.0 -0.5 +4.6 +150 UNIT
NOTES: Stresses beyond those listed cause permanent damage device. These stress ratings only functional operation device these other conditions beyond those indicated under "recommended operating conditions" implied. Exposure absolute-maximum-rated conditions extended periods affect device reliability. performance capability high-performance integrated circuit conjunction with thermal environment create junction temperatures which detrimental reliability. maximum junction temperature this integrated circuit should exceed 150°C. input output negative voltage ratings exceeded input output clamp current ratings observed.
RECOMMENDED OPERATING CONDITIONS1
SYMBOL VREF Tamb Supply voltage Termination voltage Supply voltage Input voltage HIGH-level HIGH level input voltage LOW-level level input voltage HIGH-level output current LOW-level level output current Operating free-air temperature range GTL+ GTL+ port Except port port Except port port Except port port port port PARAMETER TEST CONDITIONS 1.14 1.35 0.74 0.87 VREF 50mV VREF 50mV 1.26 1.65 0.87 1.10 UNIT
NOTE: Unused control inputs must held HIGH prevent them from floating.
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
ELECTRICAL CHARACTERISTICS
Over recommended operating conditions. Voltages referenced (ground 0V). LIMITS SYMBOL PARAMETER TEST CONDITIONS port port port Control inputs port port IOFF ICC3 port port port port control inputs Control inputs port port 3.6V; -100µA 3.0V; -12mA 3.0V; 40mA 3.0V; 12mA 3.6V; 3.6V; 3.6V; 3.6V; 3.6V; 0V;VI 4.5V 5.5V; 3.0V 3.6V;VI GND; 3.6V; -0.6V 3.0V 3.0V VCC-0.2 -40°C +85°C TYP1 UNIT
NOTES: typical values measured 3.3V Tamb 25°C. input output voltage ratings exceeded input output current ratings observed. This increase supply current each input that specified voltage level rather than GND.
CHARACTERISTICS (3.3V "0.3V RANGE)
LIMITS (GTL) SYMBOL PARAMETER WAVEFORM tPLH tPHL tPLH tPHL 3.3V "0.3V VREF 0.8V TYP1 LIMITS (GTL+) 3.3V "0.3V VREF 1.0V TYP1 UNIT
tPLH tPHL NOTE: typical values 3.3V Tamb 25°C.
SETUP REQUIREMENT (3.3V "0.3V RANGE)
Over recommended ranges supply voltage.1 LIMITS (GTL) SYMBOL PARAMETER WAVEFORM 3.3V "0.3V VREF 0.8V tS(H) tS(L) th(H) th(L) Setup time LEn) Hold time LEn) LIMITS (GTL+) 3.3V "0.3V VREF 1.0V UNIT
tw(H) pulse width NOTE: These parameters warranted production tested.
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
WAVEFORMS
1.5V 3.0V, VCC/2 2.7V ports control pins VRef ports 0.3V ports 0.3V ports VREF ports
3.0V tw(H) tPHL Output 1.5V 1.5V CONTROL INPUTS LEVELS. INPUT PULSES SUPPLIED GENERATORS HAVING FOLLOWING CHARACTERISTICS: 10MHz, 2.5ns, 2.5ns. tPLH
whichever less
Input VREF VREF tPLH tPHL
SW00333
Waveform Propagation delay, Enable Output Enable Pulse Width
SW00469
Waveform Propagation delay port port
tPLH 3.0V VOLTAGE WAVEFORMS PULSE DURATION 1.5V port 0.8V port
ts(H)
tn(H) ts(H)
3.0V Input 1.5V 1.5V tPLH tPHL Output VREF VREF VOLTAGE WAVEFORMS PROPAGATION DELAY TIMES port port
Waveform Data Setup Hold Times
SW00470
Waveform
1999
tn(H)
3.0V
whichever less
3.0V
whichever less
SW00334
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
TEST CIRCUIT
PULSE GENERATOR D.U.T.
50pF
Test Circuit switching times DEFINITIONS
Load resistor Load capacitance includes probe capacitance Termination resistance should equal ZOUT pulse generators.
SW00471
Figure Load circuitry switching times
PULSE GENERATOR D.U.T. 30pF
SW00332
Figure Load circuit outputs
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
TSSOP16: plastic thin shrink small outline package; leads; body width
SOT403-1
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
NOTES
1999
Product specification
Quad GTL/GTL+ LVTTL/TTL bidirectional latched translator
GTL2004
Data sheet status
Data sheet status Objective specification Preliminary specification Product specification Product status Development Qualification Definition This data sheet contains design target goal specifications product development. Specification change manner without notice. This data sheet contains preliminary data, supplementary data will published later date. Philips Semiconductors reserves right make changes time without notice order improve design supply best possible product. This data sheet contains final specifications. Philips Semiconductors reserves right make changes time without notice order improve design supply best possible product.
Production
Please consult most recently issued datasheet before initiating completing design.
Definitions
Short-form specification data short-form specification extracted from full data sheet with same type number title. detailed information relevant data sheet data handbook. Limiting values definition Limiting values given accordance with Absolute Maximum Rating System (IEC 134). Stress above more limiting values cause permanent damage device. These stress ratings only operation device these other conditions above those given Characteristics sections specification implied. Exposure limiting values extended periods affect device reliability. Application information Applications that described herein these products illustrative purposes only. Philips Semiconductors make representation warranty that such applications will suitable specified without further testing modification.
Disclaimers
Life support These products designed life support appliances, devices systems where malfunction these products reasonably expected result personal injury. Philips Semiconductors customers using selling these products such applications their risk agree fully indemnify Philips Semiconductors damages resulting from such application. Right make changes Philips Semiconductors reserves right make changes, without notice, products, including circuits, standard cells, and/or software, described contained herein order improve design and/or performance. Philips Semiconductors assumes responsibility liability these products, conveys license title under patent, copyright, mask work right these products, makes representations warranties that these products free from patent, copyright, mask work right infringement, unless otherwise specified. Philips Semiconductors East Arques Avenue P.O. 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 Copyright Philips Electronics North America Corporation 1999 rights reserved. Printed U.S.A. Date release: 07-99 Document order number: 9397 06247
1999

Product specification Supersedes data 1999 1999 Product specifica

Top Searches for this datasheet

Other recent searches