FH26 Series qSpace saving(51 pos. shown) 1.0mm 3.2mm 16

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

FH26 Series qSpace saving(51 pos. shown) 1.0mm 3.2mm 16

Datasheet Thumbnail

Top Searches for this datasheet

0.3mm Contact Pitch, above board, Flexible Printed Circuit Connectors
FH26 Series
qSpace saving(51 pos. shown)
1.0mm 3.2mm
16.8mm
Metal fittings protrude outside connector body
sFeatures
Extremely light weight
typical version, with contacts loaded, weights only grams.
qCan mounted over conductive traces.
Easy solderability board
soldering leads pitch, exiting front back connector.
Conductive traces under connector
exposed contacts bottom connector.
exposed contacts bottom connector
Easy insertion reliable electrical connection
Proven Flip LockR actuator allows easy insertion FPC. Tactile sensation when fully closed confirms complete electrical mechanical connection.
qOperation
Actuator open Actuator open Insert Insert
Accepts standard thickness
0.2mm thick standard Flexible Printed Circuit board used. This only ultra-low profile connector allowing standard FPC.
Actuator
Board placement with automatic equipment
Flat surface packaging tape-and-reel allows vacuum nozzles. Standard reel contains 5,000 connectors.
sApplications
Mobile phones, PDA's, digital cameras, digital video cameras, connections, plasma displays (PDP), camera modules other compact devices requiring Flexible Printed Circuit connections using high reliability ultra-small profile connectors.
Close actuator Close actuator connected connected
2004.8
sSpecifications
Rating Current rating Voltage rating 0.2A
Operating temperature range (Note Operating humidity range Relative humidity max. condensation)
Storage temperature range (Note Storage humidity range Relative humidity max.
Recommended Item
Thickness: 0.2±0.03mm tin-lead plated (Note
Specification ohms min. flashover insulation breakdown. ohms max. Including conductor resistance Contact resistance: ohms max. damage, cracks, parts dislocation. electrical discontinuity more. Contact resistance: ohms max. damage, cracks, parts dislocation. electrical discontinuity 1µs. min. Contact resistance: ohms max. damage, cracks, parts dislocation. Contact resistance: ohms max. Insulation resistance: ohms min. affect appearance performance. Contact resistance: ohms max. Insulation resistance: ohms min. damage, cracks, parts looseness. deformation components affecting performance. /one minute cycles Frequency: single amplitude 0.75 cycles, directions. Acceleration m/s2, duration, sine half-wave waveform, cycles each axis Conditions
Insulation resistance Withstanding voltage
Contact resistance Durability (Insertion/ withdrawal) Vibration
Shock
Humidity (Steady state)
hours temperature humidity 95%. Temperature: Time: (Minutes) cycles Reflow: recommended temperature profile Manual soldering: seconds
Temperature cycle
Resistance soldering heat
Note Includes temperature rise caused current flow. Note term "storage" refers products stored long period time prior mounting use. Operating Temperature Range Humidity range covers non- conducting condition installed connectors storage, shipment during transportation. Note When gold plated, connector contacts must also gold plated: Specify (05) plating code.
sMaterials
Part Insulator Actuator Contacts Metal fitting Material Phosphor bronze Color: Black Color: Dark brown Tin-lead plated (Note plated (Lead free) Finish Remarks UL94V-0
sOrdering information
FH26 (05)
Series name: FH26 contacts:
Terminal type: SHW(SMT horizontal mounting) Plating specifications
Blank: Tin-lead plated (05) Gold flash plated
Contact pitch: 0.3mm
sConnector Dimensions
(1.25) (0.3) Number contacts indicator (0.12) (0.12)
insertion slot dimension)
Notes coplanarity each terminal lead within specified dimension Packaged tape reel only. Check packaging specification.
dimensions: Part Number FH26-13S-0.3SHW FH26-21S-0.3SHW FH26-23S-0.3SHW FH26-25S-0.3SHW FH26-27S-0.3SHW FH26-33S-0.3SHW FH26-35S-0.3SHW FH26-39S-0.3SHW FH26-41S-0.3SHW FH26-45S-0.3SHW FH26-51S-0.3SHW FH26-57S-0.3SHW FH26-71S-0.3SHW CL580-0209-3 CL580-0207-8 CL580-0203-7 CL580-0208-0 CL580-0204-0 CL580-0210-2 CL580-0205-2 CL580-0201-1 CL580-0206-5 CL580-0211-5 CL580-0200-9 CL580-0212-8 CL580-0202-4 Number Contacts 11.4 12.0 13.2 13.8 15.0 16.8 18.6 22.8 10.8 11.4 12.6 14.4 16.2 20.4 10.2 11.4 12.0 13.2 15.0 16.8 21.0 4.23 6.63 7.23 7.83 8.43 10.23 10.83 12.03 12.63 13.83 15.63 17.43 21.63 10.9 11.5 12.7 13.3 14.5 16.3 18.1 22.3
Embossed tape reel packaging (5,000 pieces/reel). Order number reels.
BRecommended mounting pattern metal mask dimensions
(0.55:Metal mask) 0.65±0.05 B±0.05 (0.23:Metal mask) (0.45) (0.2) 0.3±0.03 0.6±0.05
(0.7:Metal mask)
2.15±0.05
(3.6)
0.3±0.05
Outline connector
0.8±0.05
(0.65:Metal mask)
0.3±0.05 (0.23:Metal mask) C±0.05
0.6±0.05
(0.3:Metal mask) 0.4±0.05 0.5±0.05
BRecommended Dimensions
F±0.05 1.1±0.1 1±0.1 (0.15) 1±0.1
Detail
(Lead plated MAX)
0.3±0.02
0.3+0.04 -0.03
0.3±0.1
1.1±0.1
0.6±0.02
0.2±0.03
MIN.(Stiffener)
2.25±0.1
2.1±0.1
(0.5)
0.1±0.02 (0.07) 0.6±0.07 (0.2) (0.2) B±0.03
0.3+0.04 -0.03
0.6±0.07
Overlap between covering film layer stiffener. dimensions: Part Number FH26-13S-0.3SHW FH26-21S-0.3SHW FH26-23S-0.3SHW FH26-25S-0.3SHW FH26-27S-0.3SHW FH26-33S-0.3SHW FH26-35S-0.3SHW FH26-39S-0.3SHW FH26-41S-0.3SHW FH26-45S-0.3SHW FH26-51S-0.3SHW FH26-57S-0.3SHW FH26-71S-0.3SHW CL580-0209-3 CL580-0207-8 CL580-0203-7 CL580-0208-0 CL580-0204-0 CL580-0210-2 CL580-0205-2 CL580-0201-1 CL580-0206-5 CL580-0211-5 CL580-0200-9 CL580-0212-8 CL580-0202-4 Number Contacts 10.8 11.4 12.6 14.4 16.2 20.4 10.2 11.4 12.0 13.2 15.0 16.8 21.0 10.2 10.8 12.0 12.6 13.8 15.6 17.4 21.6
0.5min.
2.5±0.3
(2.5)
0±0.03
0.3±0.07
C±0.03
0.3±0.07
0.2±0.05
0.95±0.05
BPackaging Specification
qEmbossed Carrier Tape Dimensions (Tape width 24mm max.)
(1.6) (0.3)
4±0.1
2±0.15
8±0.1
J±0.1
1.75±0.1
Unreeling direction
(3.05) (4.55) (1.25)
Flat surface, placement with automatic equipment
G±0.3
dimensions: Part Number FH26-13S-0.3SHW FH26-21S-0.3SHW FH26-23S-0.3SHW FH26-25S-0.3SHW FH26-27S-0.3SHW FH26-33S-0.3SHW FH26-35S-0.3SHW FH26-39S-0.3SHW FH26-41S-0.3SHW FH26-45S-0.3SHW FH26-51S-0.3SHW pieces reel. CL580-0209-3 CL580-0207-8 CL580-0203-7 CL580-0208-0 CL580-0204-0 CL580-0210-2 CL580-0205-2 CL580-0201-1 CL580-0206-5 CL580-0211-5 CL580-0200-9 Number Contacts 11.5 11.5 11.5 11.5 11.5 11.5 11.6 12.2 13.4 14.0 15.2 17.0 16.5 16.5 16.5 16.5 16.5 24.5 24.5 24.5 24.5 24.5 24.5
qEmbossed Carrier Tape Dimensions (Tape width 32mm min.)
(1.6) (0.3) 1.75±0.1 J±0.1 H±0.1 Unreeling direction
(3.05) (4.55) (1.25)
+0.1
+0.15
Flat surface, placement with automatic equipment
G±0.3
dimensions: Part Number FH26-57S-0.3SHW FH26-71S-0.3SHW CL580-0212-8 CL580-0202-4 Number Contacts 28.4 40.4 14.2 20.2 18.8 23.0 32.5 44.5
qReel Dimensions
Unreeling direction
section Mounting section Connectors Blank section pockets min.) Embossed carrier tape
Lead section (400mm min.)
Blank section pockets min.)
cover tape
BRecommended Temperature Profile
qUsing Typical Solder Paste
sec. max.
test conditions Solder method :Reflow, IR/hot (Nihon Den-netsu Co., Ltd.'s Part Number: SENSBY NR-2) Environment: :Room Solder composition: :Paste, 63%Sn/37%Pb (Senju Metal Industry, Co., Ltd.'s Part Number: OZ63-201C-50-9) Test board :Glass epoxy 25mm50mm0.8mm thick Land dimensions :0.3mm0.65mm,0.3mm0.8mm Metal mask :0.230.550.1mm thick, 0.230.650.1mm thick temperature profiles based above conditions. individual applications actual temperature vary,depending solder paste type, volume/thickness board size/thickness. Consult your solder paste equipment manufacturer specific recommendations.
Temperature
30sec.20 sec. sec. 60sec. sec. sec. Start Preheating Time (Seconds) Soldering
qUsing Lead-free Solder Paste
Temperature
test conditions Solder method :Reflow, IR/hot (Nihon Den-netsu Co., Ltd.'s Part Number: SENSBY NR-NR-2) Environment :Room Solder composition :Paste, 96.5%Sn/3.0%Ag/0.5%Cu (Senju Metal Industry, Co., Ltd.'s Part Number: M705-221CM5-42-10.5) Test board :Glass epoxy 25mm50mm0.8mm thick Land dimensions :0.3mm0.65mm, 0.3mm0.8mm Metal mask :0.230.550.1mm thick, 0.230.650.1mm thick temperature profiles based above conditions. individual applications actual temperature vary, depending solder paste type, volume/thickness board size/thickness. Consult your solder paste equipment manufacturer specific recommendations.
60sec. sec. sec. Start Preheating Time (Seconds) 60sec. Soldering
BRecommended Construction
qContact manufacturer specific details.
Using Single-sided
Material Name Connecting side Covering film layer. Cover adhesive Surface treatment Copper foil Base adhesive Base film Reinforcement material adhesive Stiffener Tin-lead plated 1/2oz Material Polyamide thick. Thickness (µm)
Thermosetting adhesive Polyamide thick
Thermosetting adhesive Polyamide Total thick
Back side
Using Double-sided
Material Name Connecting side Covering layer film Cover adhesive Surface treatment Through-hole copper Copper foil Base adhesive Base film Base adhesive Copper foil Cover adhesive Covering layer film Tin-lead plated 1/2oz Material Polyamide thick Thickness (µm)
Thermosetting adhesive Polyamide thick
Thermosetting adhesive 1/2oz
Thermosetting adhesive Polyamide thick
Reinforcement material adhesive Thermosetting adhesive Stiffener Back side Polyamide Total thick
prevent release it's bending, double sided with copper foil back side RECOMMENDED.
BOperation Precautions
Operation
1.FPC insertion procedure. Connector installed board.
Lift actuator. thumb index finger.
Fully insert connector parallel
mounting surface, with exposed conductive traces facing down.
conductor surface (Bottom side)
Rotate down actuator until firmly closed.
critical that inserted moved remains fully inserted.
2.FPC removal
Lift actuator. Carefully withdraw
FPC.
Precautions
Exercise care when handling connectors. Follow recommendations given below.
board flexing
board connector mounting area
connectors straight within max. Make sure that board connector mounting area flatness accept connector terminals without causing failure solder joints. SHandling before mounting Insertion operation actuator prior mounting RECOMMENDED. Board handling Exercise caution when handling boards with connectors installed. apply forces affecting soldered joints.
Connector
Precautions When Inserting Coupling
attention following points when inserting FPC.
SActuator operation apply excessive force when opening actuator prior insertion. When opening make sure
that force applied only actuator itself, avoiding touching contacts.
Actuator
Damage contacts
Damage
Axis rotation
Axis rotation
Assure free rotation actuator
Precautions
actuator will rotate degrees
135°
maximum. apply force rotate further.
When operating actuator,
center portion.
illustrated, attempt removal
positioning actuator.
Insertionq
should aligned parallel with board surface perpendicular with connector shown), then completely inserted.
Perpendicular with connector
assure correct electrical mechanical connection insert angle. must fully inserted. Make sure that MOVED during closing actuator.
Precautions
SFPC Insertionw
insert angle from above. illustrated, angle insertion cause electrical discontinuity when deflected use.
avert insertion angle, consideration should given securing insertion space time board layout. Insertion will difficult when short. *Contact manufacturer information about bending specifications.
SVerification fully closed actuator.
actuator should fully closed illustrated) held firmly connector. press against actuator when fully closed. force applied fully closed actuator should exceed
Routing (FPC fully inserted/ actuator closed)
SFPC Load
apply force excess 0.05N/pin max. upward direction illustrated). bend close actuator.
Load: 0.05N/pin max.
Precautions
Removing
Rotate actuator open position (maximum open angle 135°). Carefully withdraw FPC.
135°
Other Precautions
SHand Soldering Precautions
When hand soldering: perform reflow hand soldering with inserted connector. apply excessive heat touch soldering iron anywhere other than connector leads. excessive amount solder flux compounds. Operation actuator contacts affected excessive amounts solder flux compounds.
NOTES
NOTES
NOTES
USA: HIROSE ELECTRIC U.S.A., INC. 2688 Westhills Court, Simi Valley, 93065-6235 Phone 7958 3217 http://www.hiroseusa.com
GERMANY: HIROSE ELECTRIC GmbH Zeppelinstrasse D-73760 Ostfildern Kemnat Phone 4560021 4560729 http://www.hirose.de
NETHERLANDS: HIROSE ELECTRIC EUROPE B.V. Beechavenue 46.1119PV Schiphol-Rijk Phone 6557460 6557469 http://www.hiroseeurope.com CHINA: HIROSE ELECTRIC TRADING(SHANGHAI) CO., LTD. 3705,Bund Center,222 Road(E),Shanghai 20002 Phone 6335 2538 6335 0767
UNITED KINGDOM: KOREA: HIROSE ELECTRIC LTD. HIROSE KOREA CO., LTD. Crownhill Business Centre Vincent Avenue (#2NA311,Shihwa Industrial Complex), Crownhill, Milton Keynes 1261-10, Jeoungwhang-Dong, Shihung-City, Kyunggi-Do Phone 1908 305400 Phone 7000,7124 1908 305401 7100 http://www.hirose.co.uk http://www.hirose.co.kr HONG KONG: HIROSE ELECTRIC CO., LTD. Unit 506, Energy Plaza. Granville Road, Tsim Tsui East, Kowloon Phone 2803 5338 2591 6560 TAIWAN: HIROSE ELECTRIC TAIWAN CO., LTD. No.28 Lane Sec. Ping N,Rd.Taipei Phone 2557 7351,7352 2552 9851
SINGAPORE: HIROSE ELECTRIC CO., LTD. Anson Road #34-13 International Plaza 079903 Phone 6324 6113 6324 6123
5-23,OSAKI 5-CHOME,SHINAGAWA-KU,TOKYO 141-8587,JAPAN PHONE: 81-3-3491-9741, FAX: 81-3-3493-2933 http://www.hirose.com
contents this catalog current date publication. Contents subject change without notice purpose improvements.

FH26 Series qSpace saving(51 pos. shown) 1.0mm 3.2mm 16

Top Searches for this datasheet

Other recent searches