Download

PDF Abstract Text:

EM91465 SERIES

TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION

EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
GENERAL DESCRIPTION
FEATURES
· I.P.P. detect function prevents the illegal connect external phone. · SDO function supports LCD driver and voice synthesizer to indicate dialing numbers and function operat ing icons. · Lock function provides conventionality key lock and password lock operations. · Ring detector is designed to prevent illegal dialing from pocket dialer. · Line hold function is designed for stopping conversation temporality. · Tone / Pulse switchable. · Wide operating voltage from 2.0 V to 5.5 V. · Low operating current, 0.15 mA (Pulse) and 0.3 mA (Tone) typically. · Adding resistor on keyboard scan pin that can select many telephone specifications, such as : Pulse rate, M / B ratio, Flash time, lock dialing functions. · 13 set one touch or (3 set one touch and 10 set two touch) repertory memory, each one can hold data up to 16 digits. · A 32-digit LNB (last number) redial memory. · Keytone function provides rapidly keying recognition. · Handfree function provides on-hook dialing and speakerphone application. · Pause and P-T time are fixed to 3.6 seconds. · Tone duration and inter-tone pause time are fixed to 98 ms. · Using 3.579545 MHz crystal or ceramic resonator. · Package forms: PDIP, skinny.
ORDERING INFORMATION
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
EM91465
Pin Assignment
EM91465AP
COL5 COL4 / KT COL3 COL2 COL1 XIN XOUT XMUTE VSS 1 2 3 4 5 6 7 8 9 18 17 16 15 14 13 12 11 10 HDO PO ROW4 ROW3 ROW2 ROW1 HKS VDD DTMF
EM91465BP
COL5 COL4 / KT COL3 COL2 COL1 XIN XOUT XMUTE VSS HFI 1 2 3 4 5 6 7 8 9 10 20 19 18 17 16 15 14 13 12 11 HDO PO ROW4 ROW3 ROW2 ROW1 HKS VDD DTMF HFO
EM91465CK
ROW6 COL5 COL4 / KT COL3 COL2 COL1 XIN XOUT XMUTE VSS HFI 1 2 3 4 5 6 7 8 9 10 11 22 21 20 19 18 17 16 15 14 13 12 ROW5 / SDO HDO PO ROW4 ROW3 ROW2 ROW1 HKS VDD DTMF HFO
EM91465DK
ROW6 COL5 COL4 / KT COL3 COL2 COL1 XIN XOUT XMUTE VSS HFI DRING 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 ROW5 / SDO HDO PO ROW4 ROW3 ROW2 ROW1 HKS VDD DTMF HFO RMUTE
Keyboard Arrangement ROW5 / SDO : Option by COL5
ROW1 ROW2 ROW3 ROW4 ROW5 / SDO ROW6 COL1 1 4 7 / T M1 M6 COL2 2 5 8 0 M2 M7 COL3 3 6 9 # M3 M8 COL4 / KT HD F A RD / P M4 M9 COL5 EM1 EM2 EM3 ST M5 M10
@ When ROW5 is selected by R option (COL5), there are 13 sets one touch memory version in EM91465C / D provided.
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
FUNCTIONAL BLOCK DIAGRAM
COL1 COL2 COL3 COL4 / KT COL5 SDO Keyboard interface (column) Output circuit Row / Column programming counter HFO HDO RMUTE
XMUTE
I / O circuit
Memory
latch & decoder
D / A converter
XIN XOUT
Oscillator Timing / Control circuit
Keyboard interface (Row) VDD HFI HKS DRING Input circuit Pulse generator PO
PIN DESCRIPTIONS
Symbol ROW1~ROW6 Function Keyboard scan pins of row group. In idle state (HKS is "High" and HFO is "Low"), these pins stay "High impedance" level to prevent power consumption. Otherwise, these pins switch to "High" level for detecting keyboard entry. These pins will output 600 Hz signal while keyboard is scanning. Keyboard scan pins of column group. In idle state, these pins stay "High impedance" level. Otherwise these pins switch to "Low" level for detecting keyboard entry. These pins will output 600 Hz signal while keyboard is scanning. The fourth column group pin of the keyboard that also provides the keytone output . Normally, this pin stays "Low" level for detecting keyboard entry. After a valid keyboard entry, this pin will output keying confirmation tone that is 600 Hz signal and 30 ms duration. To prevent signal interference, while DTMF issue, it will disable key tone output except function key. Oscillator input and output pins. A 3.579545 MHz crystal or ceramic resonator must be crossed connection to XIN and XOUT pins which generate system clock. Input / Output structure pin. The output is a open drain structure. Input is schmitt trigger structure. This pin will be input pin during ON-HOOK status for illegal parallel phone detect input pin and will be output pin in OFF-HOOK condition for control speech network . Positive and negative power supply input pins. Recommended operating voltage from 2.0Vdc to 5.5Vdc. Handfree inputs pin which accepts falling edge signal to turn "on" or turn "off" handfree function. This pin is hysteresis input structure and built-in pull up resistor (typically 200 Kohms). Handfree outputs pin that is designed to control telephone line for on-hook dialing or control speakerphone circuit for handfree conversation. When handfree function is executed, this pin will switch to"High". Otherwise, this pin stays "Low" level. The DTMF (Dual Tone Multi-Frequency) signal output pin. Normally, this pin stays "Low" level. In Tone dialing mode, this pin will output DTMF signal that is corresponding to keyboard 0 . 9, and # keys.
COL1~COL3 and COL5
COL4 / KT
XIN and XOUT XMUTE
VDD and VSS HFI
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Symbol HKS
DRING
RMUTE
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
FUNCTION DESCRIPTIONS Dialing signal selection
Tf (ms) 600 100 80 300 Lock number none 0 9 0, 9
Normal dialing
Directly keying digital key on keyboard which number can be dialing output and stored in LNB memory automatically. Operating procedure described as follow : · To select Pulse or Tone mode. · Off-hook or turn on HF function. · Keying d1, d2, . , dn. The "d" expressed digital keypad that included 1~9, , 0, #, P, and PT keys. The "n" expressed unlimited. · The numbers d1, d2, . , dn will be dialed out in Pulse or Tone mode as selection.
LNB redial memory
Storing: In normal dialing mode, every digital key was entry which number will be stored in LNB memory automatically. If entry digits are more than 32 digits, the redial function of LNB memory will be disabled. Otherwise, these numbers stored in LNB memory can be redial output. This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Redialing: After normal dialing, directly keying F key (or On-Off hook once) and keying RD key on keyboard. The numbers that are stored into LNB memory will be dialed output.
Repertory memory
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Pulse to Tone ( / T) key operation The Pulse to Tone ( / T) key is designed to support toll dialing (long distance call) or PABX system operation. The " / T" key can be stored in memory and it will occupy one digital position. · To select Pulse mode. · Off-hook (or turn on HF function), push d1, d2, . , dn, / T, k1, k2, . , kn. These numbers will be dialed out as following sequence: d1, d2, . , dn, Tpt, k1, k2, . , kn. (pulse mode) (tone mode) Flash (F) key operation The Flash (F) key is designed to break telephone line temporarily. After F key is depressed, this dialer will send a flash signal to break line 600 ms, 300 ms, 100 ms or 80 ms as ROW3 and ROW4 selection. Handfree (HF) function The handfree function is designed to support on-hook dialing and loudspeaker application which can be turn "on" or "off" with falling edge signal from HFI pin. During handfree function is executed, the HFO pin is switched to "high". Otherwise the HFO pin stays "low" level. One of the following operations can turn off Handfree function (HFO pin return to "Low"). · On-off hook once. · Trigger HFI pin with falling edge signal. · Turn on Hold (HD) function. (HDO pin switched to "High") Hold (HD) function The Hold function is designed to stop conversation temporarily. In off-hook state (or HF function is turned on), to press HD key on the keyboard, the Hold function can be turned "on" (HDO pin switched to "High"). One of the following operations can turn off Hold function (HDO pin switched to "Low"). · On-off hook once. ·To press HD key over 93 ms. · Turn on Handfree (HF) function. (HFO pin switched to "High") Special Note: A 300 ms delay time (Tdly) at the first Off-Hook or turn on Handfree that is a special designed to avoid a rapid key entry (dummy number ) in this time duration , and a long distance call number follows. For example, Off-Hook , "3" , ...... , "0" , 1, 2, 3... Dummy key Lock number key The dummy number "3" is not detected by the centered office or PABX , but the following numbers "0" , 1, 2, 3.. long distance call can be dialed out normally since the leading number "3" is not the Lock-number defined in EM91465 series. To prevent the unavoidable long distance call, then EM91465 inhibits the key entry during Tdly.
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Operating flow chart
(3) Off-hook Hand-free State HF
(6) On-hook Hold-line State
(5) Off-hook Hold-line State
0 start bits 1 bit 0 bit1 bit2 bit3 data bits bit4 bit5 0 stop bits 1
Operating state
ready
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Dialing via LOCK function Conventional key lock mode. (Connects a resistor on COL1 pin to VDD) · Off hook (or turn on HF function) · Keying : d1 , d2 , . , dn . If the first number (d1) is the same with the lock number that optioned in table, then all entry numbers can not be dialed out and keyboard will be inhibited until on to off hook once again. If the first number is not equal to lock number, all the entry numbers will be dialed out. Password control mode. (Connects a resistor on COL1 pin to VSS) · Off hook (or turn on HF function) · Keying : ( # , ps1 , ps2 , ps3 + telephone number.) The numbers in the symbol could be omitted. The number "#" will be inhibited when the current password is not equal to 000, and ps1 , ps2 , ps3 work at the checking state, not to be dialed out. Other descriptions are as on following : Incorrect password entry. The telephone numbers can not be dialed out. Password is omitted . If the first digit of telephone numbers is the same with the lock number, all of the telephone numbers can not be dialed out and keyboard will be inhibited until On to Off hook once again or keying Flash. Correct password entry. The telephone numbers can be dial out no matter what lock number is. If the first digit is not equal to the lock number then the telephone numbers will be dialed out entirely and use the Flash key to redial any other number will not check the pass word again.
Ring detector
The Ring detector is designed to prevent illegal dialing from pocket dialer. Following the procedures ( i, ii, iii ), this dialer will detect DRING pin to control RMUTE output level. If DRING is detected a "Low" level, the RMUTE stays "High impedance". If DRING is detected a "High" level, the RMUTE will output "Low" until keyboard entry. In actual application of the RMUTE pin is recommended connection to microphone of the phone handset to prevent that the dialing signal (DTMF) is coupling by the Microphone of the phone handset. (such as pocket dialer) i. In idle state, HKS is from "High" to "Low" (pick up handset action). ii. In idle state, turn on handfree function. iii. The flash operation ( F key ). I.P.P. DETECT function The EM91465 series provide the I.P.P. function to pretect illegal connect. I.P.P means Illegal Parallel Phone Detect. I.P.P. function depend on XMUTE pin and HKS, HF status. When in the ON-HOOK condition and HF turn off, the XMUTE pin will be a Input pin to detect the voltage lever, otherwises, the XMUTE pin will be a normally output pin use for control speech network. When I.P.P. function detect. XMUTE pin at "low" status (In On-Hook and HF turn OFF state), EM91465 will turn on HF and HDO then send alarm signal to telephone line. In alarm duration DTMF pin will continue sending "#", "8" "8" signal. The DTMF signal will interfere the illegal user until the illegal user hang up the phone and the pin detect "high" again. The telephone circuit design can allow the illegal internal connect user. (see I.P.P Application CIRCUIT).
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
ABSOLUTE MAXIMUM RATINGS(Ambient temperature is 25 °C, all voltages referenced to VSS)
Items Power supply voltage Input voltage range Operating temperature Storage temperature Power consumption Sym. VDD VIN TOPR TSTO PD Rating 6.0 Vdc VSS-0.3V ~ VDD+0.3V 0 ~ 50 -55 ~ 125 500 Unit V V °C °C mW
DC ELECTRICAL CHARACTERISTICS
Min. 2.0 2.0 0.8VDD VSS VSS 0.7VDD 0.2 -0.2 2 200 0.2 0.2 -0.2 0.5 142 1 5
Typ. 0.15 0.3 1 10 200 10 400 160 2 -30 -
Max. Unit 5.5 5.5 0.3 0.5 0.1 0.1 10 0.1 30 VDD 0.2VDD 0.3VDD VDD 0.01 50 800 0.75 180 3 -23 V mA uA uA
Idd Imrt Istby
This specification are subject to be changed without notice.
HKS, HFI & DRING pins: input voltage Xmute pin : Schmitt triggers (input pin) HFO & HDO pins source current PO, HFO, XMUTE, RMUTE & SDO pins: sink current PO, XMUTE, RMUTE and SDO pins: leakage current HFI pin input resistance Keyboard scanning pins output current (except COL4 / KT) COL4 / KT source current sink current DTMF pin: sink current DTMF signal DC level DTMF signal: ac level pre-emphase distortion load resistance
ViH ViL VH-L VL-H IoH IoL IoH Rhfi IoH IoL IoH IoL IoL Vdc Vdtmf Twist THD ZL
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
AC ELECTRICAL CHARACTERISTIC
Parameter Keyboard debounce time Key tone signal: frequency duration Pause time Pulse to Tone waiting time Flash time
Sym. Tdb Fkt Tkt Tp Tpt Tf
Min. 96 96 3.8 -
Typ. 20 600 30 3.6 3.6 600 100 80 300 20 10 40:60 33:66 800 500 98 98 93 3.9 300
Max. Unit 100 100 4.1 ms Hz ms sec. sec. ms
Condition
Pulse rate Make / Break ratio Inter-digit pause time Minimum tone duration Minimum inter-tone pause HD key release hold function debounce time SDO bit time Off-Hook delay time
PSR MBR Tidp Tp Titp Thdrdb Tbit Tdly
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
TIMING DIAGRAM
HKS KEY IN Tdb KT Tkt XMUTE SDO PO Tidp DTMF OSC. Tdly
Hi-impedance
Figure 1. Pulse mode operating timing
HKS KEY IN KT XMUTE SDO PO DTMF OSC.
Hi-impedance
Figure 2. DTMF mode operating timing
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Hi-impedance
Figure 3. Pulse mode LNB redial timing
Hi-impedance
Td Titp
Figure 4. DTMF mode LNB redial timing
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
HKS KEY IN KT XMUTE Tp SDO PO DTMF OSC. Tidp Tidp
Figure 5. Pause key operating timing
HKS KEY IN KT XMUTE Tpt 2 / T 3 4
Hi-impedance
SDO PO DTMF OSC.
Figure 6. Pulse to Tone (PT) operating timing
Hi-impedance
Figure 7. Flash key operating timing This specification are subject to be changed without notice.
Hi-impedance
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
HKS KEY IN Tdb KT SDO
b1 b2 b3 b4 b5 SPB SPB
Hi-impedance
HKS KEY IN HFO HDO XMUTE SDO PO HF HD HF HD HD HD HF HD HD @ 93 ms Thdrdb
MELODY Hi-impedance
@ : It can be triggled by extension telephone set for hold function release Figure 9. HF and HD operating timing
HFI or HKS KEY
KT Tdly OSC. "0" digit dialing time SDO
Hi-impedance
Figure 10. Off-Hook delay time This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
Toff RING Ton DRING HKS RMUTE
Figure 11. Timing of receiving an incoming call The external ring detection circuit must send a low signal at the total ring cycle (Ton and Toff)
RING DRING HKS RMUTE
Figure 12. Timing of making an outgoing call
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
APPLICATION CIRCUIT : CONTROL AND IPP DETECT
NETWORK
RMUTE
SPEECH
13 HFO 14 15
RMUTE HFO DTMF
DRING HFI VSS
DRING
XMUTE
EM91465DK
VDD HKS ROW1 ROW2 ROW3 ROW4 PO HDO ROW5 / SDO
XMUTE XOUT XIN COL1 COL2 COL3 KT / COL4 COL5 ROW6
HF 3.58M BUZZER
0.01u
LCD DRIVER
0.001u
1N4148
KEYBORAD AND HOLD
1N4148
DRING
BRIDGE
PC817
0.22u / 50V
BRIDGE
This specification are subject to be changed without notice.
BRIDGE
PC817
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
APPLICATION CIRCUIT : KEY BOARD AND HOLD
FLASH TIME
LOCK NUMBER
COL4 / KT
AUTOMATICALLY HOLD RELEASE CIRCUIT
22K 47K
This specification are subject to be changed without notice.
R-option
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
APPLICATION CIRCUIT : LCD DRIVER USE EM32117
VDD GF
SEG0 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 COM0 COM1 COM2 COM3
ENRTC
SEG26
ENCLND
SEG27
SEG28
SEG29
SEG30
SEG31
EXTRA 1.5V BATTERY
CALENDAR
SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 MS1 MS2 SPARE1 SPARE2 SDI HKS VDD V2 V3 VC1 VC2 VSS XIN XOUT 27 28 29 30 31 32 34 35 37 38 39 40 36 33
EM32117
LCD PANEL
GF JUMP : General Flag icon for LOGO ON / OFF CALENDAR JUMP : CALENDAR ON / OFF
MS1 MS1 , MS2 adjust Time
RECOMMAND CRICUIT :
This specification are subject to be changed without notice.
NOTED :
DIALER PART VDD
1N4148
RTC HOUR
JUMP : Real Time Clock ON / OFF JUMP : 24 / 12 format select
VDD HKS
HOUR SDI
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
APPLICATION CIRCUIT : LCD DRIVER USE EM32100
TEST AND F32H 45 46 42 43 37 38 39 40 41 44 47 48
TEST2
LCD PANEL
SEG17
SEG18
SEG19
SEG20
SEG21
SEG22
SEG23
SEG24
COM3 COM2 COM1 SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
TEST1
SEG6 SEG7 SEG8 SEG9 NC SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 VN NC VP
MS1 MS2 SDI HKS VDD XIN NC XOUT VSS 24 / 12 ENRTC NC
EM32100
20p 20p
JUMP : Real Time Clock ON / OFF RTC
EM32100 need HDO and HFO
MS1 , MS2 adjust Time SDO
EXTRA 1.5V BATTERY
1N4148
This specification are subject to be changed without notice.
NOTED :
JUMP : 24 / 12 format select
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
PACKAGE INFORMATION
Example : EM (1) 914XX P (2) (3) (1) ELAN MICRO. pefix (2) Type number (3) Package code: PPDIP KSkinny RSDIP 18 / 20 / 28 Lead Plastic Package
18 PDIP
DIM A A1 B B1 C D E E1 e eB L MILIMETERS MIN. MAX. 5.334 0.381 0.356 0.558 1.150 1.778 0.204 0.381 22.35 23.37 7.620 8.255 6.096 7.112 2.286 2.794 10.92 2.921 4.064
20 PDIP
INCHES MILIMETERS INCHES MIN. MAX. DIM MIN. MAX. MIN. MAX. .210 A 5.334 .210 .015 A1 0.381 .015 .014 .022 B 0.356 0.558 .014 .022 .045 .070 B1 1.150 1.778 .045 .070 .008 .015 C 0.204 0.381 .008 .015 .880 .920 D 25.40 26.67 1.000 1.050 .300 .325 E 7.620 8.255 .300 .325 .240 .280 E1 6.096 7.112 .240 .280 .090 .110 e 2.286 2.794 .090 .110 .430 eB 10.92 .430 .115 .160 L 2.921 4.064 .115 .160 DIM A A1 B B1 C D E E1 e eB L MILIMETERS MIN. MAX. 6.350 0.381 0.356 0.558 1.016 1.778 0.204 0.381 35.56 37.85 15.24 15.88 13.21 14.73 2.286 2.794 17.78 2.921 5.080
28 PDIP
INCHES MIN. MAX. .250 .015 .014 .022 .040 .070 .008 .015 1.400 1.490 .600 .625 .520 .580 .090 .110 .700 .115 .200
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
22 / 24 Lead Plastic Package-Skinny
22 PDIP (skinny)
DIM A A1 B B1 C D E E1 e eB L MILIMETERS MIN. MAX. 4.752 0.381 0.356 0.558 1.27 1.778 0.204 3.556 25.90 26.67 7.620 8.255 6.223 6.604 2.286 2.794 8.382 10.16 2.921 4.064 INCHES MIN. MAX. .180 .015 .014 .022 .050 .070 .008 .014 1.02 1.05 .300 .325 .245 .260 .090 .110 .330 .400 .115 .160 DIM A A1 B B1 C D E E1 e eB L
24 PDIP (skinny)
MILIMETERS MIN. MAX. 4.572 0.381 0.356 0.558 1.27 1.778 0.204 0.381 31.24 32.26 7.620 8.255 6.223 6.731 2.286 2.794 8.636 9.652 2.921 4.064 INCHES MIN. MAX. .180 .015 .014 .022 .050 .070 .008 .015 1.23 1.270 .300 .325 .245 .265 .090 .110 .340 .380 .115 .160
This specification are subject to be changed without notice.
EM91465 SERIES
TONE / PULSE SWITCHABLE DIALER WITH LCD INTERFACE AND I.P.P. DETECT FUNCTION
42 SDIP Package
42 SDIP
DIM A A1 A2 B B1 C D E1 e eB D1 L MILIMETERS MIN. MAX. 5.08 0.381 3.937 4.191 0.356 0.559 0.914 1.116 0.204 0.304 36.70 37.34 13.84 14.10 1.727 1.829 15.24 17.78 0 0.127 2.921 3.429 INCHES MIN. MAX. 0.200 0.015 0.155 0.165 0.014 0.022 0.036 0.044 0.008 0.012 1.445 1.470 0.545 0.555 0.068 0.072 0.600 0.70 0 0.005 0.115 0.135
This specification are subject to be changed without notice.