MAX4104 Evaluation MAX4104 evaluation kit) simplifies evaluation

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

MAX4104 Evaluation MAX4104 evaluation kit) simplifies evaluation

Datasheet Thumbnail

Top Searches for this datasheet

19-4757; 10/98
MAX4104 Evaluation
MAX4104 evaluation kit) simplifies evaluation MAX4104 ultra-high-speed, low-noise, 880MHz amplifier. circuit demonstrates MAX4104 noninverting unity-gain configuration. RF-style connectors (SMA) terminating resistors included test equipment compatibility. MAX4104 also used evaluate MAX4105, MAX4304, MAX4305. Simply order free sample appropriate part (MAX4105ESA, MAX4304ESA, MAX4305ESA), replace board, change gain-setting resistors desired gain. Refer MAX4104/MAX4105/ MAX4304/MAX4305 data sheet suggested resistor values.
_Features
880MHz (typical) -3dB Bandwidth 100MHz 0.1dB Gain Flatness 2.1nV/Hz Voltage Noise Density 400V/µs Slew Rate ±70mA Output Current Drive -88dBc SFDR 50MHz) Fully Assembled Tested Surface-Mount Board
Evaluates: MAX4104/MAX4105/MAX4304/MAX4305
_Quick Start Ordering Information
PART MAX4104EVKIT TEMP. RANGE -40°C +85°C PACKAGE
Component List
DESIGNATION None None DESCRIPTION 10µF, 10V, tantalum capacitors TAJB106M010 Sprague 293D106X0010B 0.1µF ceramic capacitors connectors 49.9, resistors resistor Open MAX4104ESA MAX4104 board MAX4104/MAX4105/MAX4304/ MAX4305 data sheet
MAX4104 fully assembled tested. Follow these steps verify board operation. turn power supply until connections completed. circuit requires supply voltages ±3.5V ±5.5V. evaluation purposes, connect supply labeled supply labeled VEE. Connect power-supply grounds marked GND. Connect output marked oscilloscope through terminated cable. Turn power supply. Apply signal ±3.4V maximum connector marked Verify output signal oscilloscope. Note: when using terminated oscilloscope input, output amplitude observed oscilloscope will half that input, voltage divider formed 49.9 back-terminating resistor (R2) oscilloscope input termination impedance.
_Layout Considerations
MAX4104 layout been optimized high-speed signals distortion, with careful attention given grounding, power-supply bypassing, signal-path layout. small, surface-mount, ceramic bypass capacitors have been placed close MAX4104 supply pins possible. continuous ground plane been maintained under reduce inductance signal return path. Capacitance inverting input been minimized reducing feedbacktrace length using 0805-size surface-mount feedback gain-set resistors.
Component Suppliers
SUPPLIER Sprague PHONE 803-946-0690 603-224-1961 803-626-3123 603-224-1430
Note: Please indicate that using MAX4104 when contacting these component suppliers.
Maxim Integrated Products
free samples latest literature: http://www.maxim-ic.com, phone 1-800-998-8800. small orders, phone 1-800-865-8769.
MAX4104 Evaluation Evaluates: MAX4104/MAX4105/MAX4304/MAX4305
N.C.
N.C.
OPEN
MAX4104
0.1µF 10µF
49.9
49.9
10µF 0.1µF
N.C.
Figure MAX4104 Schematic
MAX4104 Evaluation Evaluates: MAX4104/MAX4105/MAX4304/MAX4305
1.0"
Figure MAX4104 Component Placement Guide- Component Side
1.0"
Figure MAX4104 Board Layout-Component Side
1.0"
Figure MAX4104 Board Layout-Solder Side
MAX4104 Evaluation Evaluates: MAX4104/MAX4105/MAX4304/MAX4305
NOTES
Maxim cannot assume responsibility circuitry other than circuitry entirely embodied Maxim product. circuit patent licenses implied. Maxim reserves right change circuitry specifications without notice time.
_Maxim Integrated Products, Gabriel Drive, Sunnyvale, 94086 408-737-7600 1998 Maxim Integrated Products Printed registered trademark Maxim Integrated Products.

MAX4104 Evaluation MAX4104 evaluation kit) simplifies evaluation

Top Searches for this datasheet

Other recent searches