SURFACE MOUNT SUPPRESSORS PRODUCT OVERVIEW 8-Line CA10 Obsoleted

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SURFACE MOUNT SUPPRESSORS PRODUCT OVERVIEW 8-Line CA10 Obsoleted

Datasheet Thumbnail

Top Searches for this datasheet

PULSEGUARD® SUPPRESSOR
SURFACE MOUNT SUPPRESSORS PRODUCT OVERVIEW
8-Line CA10 Obsoleted Part. Please consider PGB0010603, PGB002ST23 PGB0040805 designs.
PulseGuard Suppressors help protect sensitive electronic equipment against electrostatic discharge (ESD). They supplement on-chip protection integrated circuitry best suited low-voltage, high-speed applications where capacitance important. Applications such computer ports (eg. video displays), network hardware, cell phone data ports, point-ofsale terminals, industrial controls will benefit from this technology. PulseGuard suppressors polymer composite materials suppress fast-rising transients specified 61000-4-2 MIL-STD883E).
FEATURES
Ultra-low capacitance leakage current Fast response time Bi-directional Withstands multiple strikes Packaged chip array (capacitor/resistor) format Compatible with pick-and-place processes Available 2,000 piece reels (EIA-RS481)
PHYSICAL SPECIFICATIONS
Materials: Body: Glass Epoxy Terminations: Tin-Lead Soldering Parameters: Wave solder 260oC, seconds maximum Reflow solder 260oC, seconds maximum Operating Temperature Range: -65oC +125oC
TYPICAL APPLICATIONS
Computer ports (e.g. video displays) Computer peripherals Network hardware/ports (e.g. Gigabit Ethernet) Point-of-Sale terminals Cell phone data ports Audio/video components Test Equipment Medical Equipment
ORDERING INFORMATION Catalog Number Pieces Reel
PGB008CA10PR 2,000
ELECTRICAL CHARACTERISTICS
Trigger Voltage1 Clamping Voltage1 Rated Voltage Capacitance2 Response Time1 Leakage Current3 Pulse Withstand1 1,000V, typical 150V, typical 24VDC, 0.055pF <1ns <1nA 1,000 pulses, minimum
DESIGN CONSIDERATION
Because fast rise-time transient, placement PulseGuard suppressors design consideration. achieve optimal suppression, devices should placed circuit board close source transient possible. Install PulseGuard suppressors directly behind connector that they first board-level circuit component encountered transient. They connected from signal/data line ground.
Notes: direct discharge method, 61000-4-2. Measured MHz. Measured VDC. Testing fast pulse rates (1-20Hz) cause change leakage current performance (6µA, max).
PULSEGUARD® SUPPRESSOR
SURFACE MOUNT SUPPRESSORS
8-Line CA10
Generalized PulseGuard Response
(Positive Negative Polarity Pulses)
Trigger Voltage
Generalized Curve
(Positive Negative Polarity Pulses)
Trigger Voltage Current
Voltage
Clamping Voltage
Clamping Voltage Voltage
Time (ns)
DEFINITIONS
Trigger Voltage: measured peak voltage across suppressor before transitions from high resistance. manifested "spike" before clamping voltage achieved. This voltage typically well below damage threshold on-chip protection. Clamping Voltage: voltage level which impulse voltage reduced. This voltage that suppressor holds until transient energy dissipated. Impulse Voltage: Also known Threat Voltage. This voltage that "zapped" into circuit. Voltages generated people exceed 61000-4-2 defines four levels impulse voltage testing purposes:
SEVERITY LEVEL DISCHARGE DIRECT DISCHARGE
Capacitance Frequency
Note: 1,000
Capacitance (fF)
Frequency (GHz)
Carrier Tape Specifications
Parts delivered (178mm) reel, plastic carrier tape
Description Cover tape thickness Drive hole diameter Drive hole spacing Pocket depth Pocket height Pocket spacing Pocket width Carrier tape thickness Carrier tape width
Measurement (mm) 0.06 1.50 4.00 1.02 5.38 4.00 2.44 0.30 12.00
PULSEGUARD® SUPPRESSOR
SURFACE MOUNT SUPPRESSORS
8-Line CA10
Test Set-up 61000-4-2 Waveform, 2kV-15kV
Device under test P6156 Probe (Voltage measurement) KeyTek pulser 2,000- 15,000 Brown (x100)
Faraday cage
Ground return
Tektronic 684B
Blue (x10) shunt (10-5 ohms parallel) P6156 Probe (Current measurement)
Reference Schematics:
Recommended Layout: Device Dimensions:
0.083"
0.007
Equivalent Circuit:
0.043"
0.198"
0.008
*Dimension 0.026" *Dimension 0.015"
Solder Method
Wave Solder Reflow Solder
0.036 0.025
0.060 0.050
Dimensions (in.)
0.119 0.101 0.047 0.051 0.043 0.043
0.030 0.030
0.198 0.191
Note: Pins (Common) typically connected chassis ground. However since PulseGuard suppressors bi-directional, system voltage also used "dump".

SURFACE MOUNT SUPPRESSORS PRODUCT OVERVIEW 8-Line CA10 Obsoleted

Top Searches for this datasheet

Other recent searches