MAX2754 Evaluation MAX2754 evaluation kit) simplifies evaluation

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

MAX2754 Evaluation MAX2754 evaluation kit) simplifies evaluation

Datasheet Thumbnail

Top Searches for this datasheet

19-2102; 10/94 XX-XXXX;Rev 7/01
MAX2754 Evaluation
MAX2754 evaluation kit) simplifies evaluation MAX2754 VCO. This enables testing device's performance requires additional support circuitry. signal output uses connector facilitate connection test equipment. Easy Evaluation MAX2754 +2.7V +5.5V Single-Supply Operation Output Matched Critical Peripheral Components Included
Features
Evaluates: MAX2754
Component List
DESIGNATION DESCRIPTION 0.33µF ±10% ceramic capacitor (0603) Murata GRM36 334K016 1000pF ±10% ceramic capacitors (0402) Murata GRM36X7R102K050 installed 330pF ±10% ceramic capacitor (0402) Murata GRM36X7R331K050 0.1µF ±10% ceramic capacitor (0603) Murata GRM39X7R104K016 resistors (0402) resistor (0402) connectors (edge-mount) EFJohnson 142-0701-801 Digi-Key J502-ND Test points, 1-pin header Mouser 151-203 equivalent Jumper, SIP3, 3-pin header Digi-Key S9000-ND equivalent PART MAX2754EVKIT
Ordering Information
TEMP. RANGE -40°C +85°C PACKAGE µMAX
Test Equipment Required
This section lists recommended test equipment verify operation MAX2754. intended guide only, some substitutions possible. Three power supplies +2.7V +5.5V ammeter (optional) spectrum analyzer 8561E, example) that covers operating frequency range MAX2754, well harmonics cable
MOD, GND, SHDN, TUNE,
Connections Setup
This section provides step-by-step guide functions operation these kits. Connect supply (through ammeter, desired) terminals kit. Apply SHDN control input. Turn supply. supply current should read about 13.5mA. Connect output spectrum analyzer with coaxial cable (minimize length). Apply variable voltage TUNE input (+0.4V +2.4V). Check fMIN fMAX spectrum analyzer varying tuning voltage. Apply variable voltage input (+0.4V +2.4V). Check modulation peak frequency deviation spectrum analyzer varying modulation voltage. Check output power level (-5dBm typ).
Component Suppliers
SUPPLIER Murata Electronics Taiyo Yuden PHONE 800-831-9172 408-573-4150 814-238-0490 408-573-4159
Note: Please indicate that using MAX2754 when contacting these component suppliers.
Quick Start
MAX2754 fully assembled factory tested. Follow instructions Connections Setup section proper device evaluation.
Maxim Integrated Products
pricing, delivery, ordering information, please contact Maxim/Dallas Direct! 1-888-629-4642, visit Maxim's website www.maxim-ic.com.
MAX2754 Evaluation Evaluate: MAX2754
0.33µF VREG 330pF OPEN SLIDING CAP. GND2 1000pF 0.1µF
TUNE
1000pF
TUNE
MAX2754
OPEN GND1
SHDN
SHDN
Figure MAX2754 Schematic
1.0"
1.0"
Figure MAX2754 Component Placement Guide-Top Silkscreen
Figure MAX2754 Board Layout-Component Side
1.0"
Figure MAX2754 Board Layout-Ground Plane
Maxim cannot assume responsibility circuitry other than circuitry entirely embodied Maxim product. circuit patent licenses implied. Maxim reserves right change circuitry specifications without notice time.
_Maxim Integrated Products, Gabriel Drive, Sunnyvale, 94086 408-737-7600 2001 Maxim Integrated Products Printed registered trademark Maxim Integrated Products.

MAX2754 Evaluation MAX2754 evaluation kit) simplifies evaluation

Top Searches for this datasheet

Other recent searches