The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.    


Datasheet Search Engine   
 
Part # or Description: • 5V RS232 Driver • 2SC5066* • "Real Time Clock" • "USB connector" • "blue led" 5mm • 10 watt zener diode • 2N3055* motorola
 
Search Tip: Try entering the part number only. Include a wildcard (eg. lm317* or 1n4148*)

 

 

***** Supporting MPPMC603 Talos MPPMC740 Talos MPPMC745 Talo


Datasheet Thumbnail

  

Download PDF



Top Searches for this datasheet



Sandpoint
*****
Supporting
MPPMC603 Talos MPPMC740 Talos MPPMC745 Talos MPPMC8240 Unity MPPMC8245 Unity MPPMC8260 Cygnus MPPMC750 Altimus MPPMC755 Altimus MPPMC7400 Altimus MPPMC7410 Altimus MPPMC7450 Valis .tbd.
This schematic provided reference purposes only. information subject change without notice. warranty, expressed applied, made accuracy information contained herein. Contact Motorola Sale/FAEs obtain latest information this product.
*Digital
from Motorola
Schematic Notes
Unless otherwise specified: resistors SMD0603, ohms, 0.1W, +/-5% capacitors SMD0603, microfarads (uF), +/-20%. inductances microhenries (uH). ferrites Z=50 ohms MHz. fuses self-resetting polyswitch (PTC) devices. Board impedance 50-60 ohms. Integrated circuits have default connections power ground unless explicitly shown otherwise. Global power connections are: VCC_3.3V VCC_5V Part numbers used reference only; compatible parts used; refer bill materials. Motorola Motorola logo registered trademarks Motorola. PowerPC trademark IBM. Other trademarks respective property their respective copyright holders. Diane, holding hand small, chocolate bunnies. rights reserved. sheet-to-sheet cross reference format Sheet VertZoneLetter HorizZoneNumber Components with property "no_stuff" installed default; they test manufacturing purposes only.
Page
Contents Cover Page General Information Block Diagram Routing Layout Information Power Supply Clock Generation Processor Socket 64-bit Connector PCI/ISA Bridge Connectors Super Controller Floppy, Connectors Serial Ports Slots Slots Boot ROMs, NVRAM SPF100 Arbiter/Interrupt Controller Configuration Switches; Monitor LEDs Pullups
buses follow big-endian numbering order (bit most-significant bit), except where industry standards apply (i.e. PCI). Little-endian numbering noted source component.
Sandpoint
Team Sandpoint
Cindy Black Ivan Erickson Gary Milliorn Tony Saucedo Joey Tsai Gary Wojcik
Program Mgr. Designer Components Documentation Imperial Poobah
CHANGES DATE 98MAR23 Original 98DEC11 00JUL26
Connector orientation; crosspoint tweaks. Many changes
GARY MILLIORN
Connector
32/64 PPMC Extensions Extensions
<07-08>
Power Supply
Chassis Header
<05>
32-bit/64-bit 33/66 System Clocks
PCI: Clocks.
<06>
Connectors
33/66-MHz ATAPI
<10>
Southbridge
Winbond W53C55x
<09>
Slots
32-bit slots 64-bit slots
<14,15>
Reset Logic
Chassis Headers
<05>
Interrupt Routing Non-Volatile
<17>
Super Controller
National 87307
<16> <11>
Boot Flash
512KB
<16>
bytes APC/RTC Power Supply
Arbitration Routing Ports
<17>
PS/2 Keyboard Mouse Parallel Port Floppy Serial Ports
<12,13>
Layout/Routing Instructions
split power planes 3.3V power. Place header lower-left hand corner board (I/O connectors would upper right. Allow clearance around header allow silkscreen legends. Label groups shown.
Port
CHASSIS
SPKR
Keep series termination resistors near output pins. Route clock lengths equal WBCLK trace less 2.5" heavy traces power path through filter: +3.3V VCCO pins Rxxx/Rxxx Combo VCCI Pin. Surround MPC972 with 0.1uF caps provide good ground-return paths. Keep XTAL1 jumper insanely close. Place side board. equal-length traces nets DAK(2:0) from WinBond 'F138. Place series termination resistors near socket. very short traces from 32kHz crystal SuperI/O connected components. Allow other traces enter cross crystal oscillator area. traces VBAT VSTDBY. Place filtering caps ferrite beads very close DIN6 DB25 connectors. Place series resistors parallel port near DB25 connector. Keep traces very short between RS232 drivers (U1, connectors. traces +12V -12V. Place IDSEL resistor near IDSEL pin. Place IDSEL resistor near IDSEL pin. traces between battery connector diodes (before after). special restrictions. special restrictions. Recommended placement status LEDs under disk tray area. Place LEDs order label with indicated text. Follow chassis specs mounting hole sizes plated area allowance. Distribute capacitors shown, unless otherwise specified. Keep traces short possible. swapping within without package encouraged order minimize trace length.
GARY MILLIORN
RESET SWITCH DISK STDBY
Chassis Mounting Holes
NVRAM SOURCING
Select VSTDBY battery available.
Local Reset Switch
Chassis Cable Header
Place lower-left hand corner board cable connection.
Local Power Switch
TEST CLOCK INPUT
Select CLKOFF select external 50ohm clock source.
CLOCK EQUALIZATION
Route indicated clocks match WBCLK less inches specifications.
SELECT
Select 3.3V option. Default:
PRIMARY
SECONDARY
32kHz Oscillator
Keep traces extremely short. Route traces through that area.
Floppy connector
PS/2 Keyboard
PS/2 Mouse
Parallel Port
Right-angle mount
Serial Port
Serial Port
Slot
IDSEL AD13 Closest PMC.
Slot
IDSEL AD14 Next-closest PMC.
Slot
IDSEL AD15 Third from PMC.
Slot
IDSEL AD16 Furthest from PMC.
Diagnostic LEDs
Place visible area.

Other recent searches


STV942x - STV942x   STV942x Datasheet
STV942X - STV942X   STV942X Datasheet
NJW1128 - NJW1128   NJW1128 Datasheet
NJW1124 - NJW1124   NJW1124 Datasheet
MF733-03 - MF733-03   MF733-03 Datasheet
MAX15059 - MAX15059   MAX15059 Datasheet
MAX15059AETE+ - MAX15059AETE+   MAX15059AETE+ Datasheet
MAX15059BETE+ - MAX15059BETE+   MAX15059BETE+ Datasheet
ISP2312 - ISP2312   ISP2312 Datasheet
IRU1075 - IRU1075   IRU1075 Datasheet
Al203 - Al203   Al203 Datasheet
2SK1623 - 2SK1623   2SK1623 Datasheet

 

Privacy Policy | Disclaimer
© 2012 Datasheet Archive