SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp 3.3

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp 3.3

Datasheet Thumbnail

Top Searches for this datasheet

PI7AT04
SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp
3.3V Line Clamping Near Zero Quiescent Supply Current: 10µA Maximum Active circuit clamping Capacitance: (typ.) High Protection Packaging (Pb-free Green Available): 6-pin SC70
Description
PI7AT04 actively clamps overshoot undershoot voltages transmission lines backplanes. Improperly terminated data lines have reflections that result lost data unreliable system behavior. PI7AT04 clamps undershoot overshoot voltages four lines. other options packages contact Pericom Marketing. Compared Schottky diodes, PI7AT04 uses less power requires additional drive power. avoiding passive termination/clamp technology, PI7AT04 power consumption very PI7AT04 ideal applications where characteristic impedance varies with system configuration. Changing characteristic impedance common when memory function cards added removed bus. PI7AT04 does replace parallel terminator resistors.
Benefits
Reduced Limits high-frequency ring voltage Minimum Power Consumption Higher Noise Margin Minimal Line Loading
Applications
Termination Backplane Termination Termination
Product Configuration
Product Description
Numbe 6-pin, SC70 Name cription Line Termination Line Termination Line Termination Line Termination Ground Positive Supply Voltage
6-Pin
Functional Block Diagram
Control Input
PS8588C
08/02/04
PI7AT04 SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp
Absolute Maximum Ratings
Voltage Storage Temperature Lead Temperature (Soldering, seconds) rmal Information MSOP Continuous Power Dissipation: derate 8.7mW/°C above 70°C) SC70/SOT23 Continuous Power Dissipation: derate 7.0mW/°C above 70°C) 650mW 550mW 6.5V -65°C 150°C 300°C
Electrical Characteristics
Over Operating Temperature Range, unless otherwise noted.
Parame Line Signal Voltage Above Line Signal Voltage Below Input Line Capacitance Input High Current Input Current Supply Voltage Range Quiescent Supply Current Protection
Symbol Note Note
Conditions
-0.6
Units
Line Voltage VLINE VDD, 5.5V VLINE 5.5V
lines floating MIL- STD- 883, Method 3015
3.3V Over Operating Temperature Range, unless otherwise noted.
Parame Line Signal Voltage Above Line Signal Voltage Below Input Line Capacitance Input High Current Input Current Supply Voltage Range Quiescent Supply Current Protection
Symbol Note Note
Conditions
Typ. -0.6
Units
Line Voltage VLINE VDD, 3.6V VLINE 3.6V
lines floating MIL- STD- 883, Method 3015
Notes: Capacitance parameters guaranteed design. Maximum line voltage clamped during transient.
PS8588C
08/02/04
PI7AT04 SOTINYLow Voltage, Zero-Delay,
Active Transmission Line Clamp
Application Information
Driver 74VCX16244 Transmission Line Receiver 74VCX16244
PI7AT04
Figure Test Diagram
6.5V
3.5V
10ns/div.
Figure VCX16244 (Vcc 3.6V) output after driving 3-inch transmission line. Signal capture line
6.5V
3.6V
3.5V
10ns/div.
Figure VCX16244 (Vcc 3.6V) output after driving 3-inch transmission line driving PI7AT04 input. Signal seen input pin. Signal capture when 3.6V.
PS8588C 08/02/04
PI7AT04 SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp
Packaging Mechanical: 6-Pin SC70
Notes: Controlling dimensions millimeters Ref: JEDEC MO-203AB
Ordering Information
Ordering Code PI7AT04CX PI7AT04CEX Line Terminations Package Code Package Description 6-pin SC70 6-pin SC70 Marking
Notes: Thermal Characteristics found world wide www.pericom.com/packaging/ Tape reel
Pericom Semiconductor Corporation
1-800-435-2336 www.pericom.com
PS8588C 08/02/04

SOTINYLow Voltage, Zero-Delay, Active Transmission Line Clamp 3.3

Top Searches for this datasheet

Other recent searches