MC74HC164A identical pinout LS164. device inputs compatible with stand
|
|
|
Top Searches for this datasheet
MC74HC164A 8-Bit Serial-Input/Parallel- Output Shift Register
MC74HC164A identical pinout LS164. device inputs compatible with standard CMOS outputs; with pullup resistors, they compatible with LSTTL outputs. MC74HC164A 8-bit, serial-input parallel-output shift register. serial data inputs, provided that input used data enable. Data entered each rising edge clock. active-low asynchronous Reset overrides Clock Serial Data inputs.
PDIP-14 SUFFIX CASE
MC74HC164AN AWLYYWWG
Output Drive Capability: LSTTL Loads Outputs Directly Interface CMOS, NMOS, Operating Voltage Range: Input Current: High Noise Immunity Characteristic CMOS Devices Compliance with JEDEC Standard Requirements Chip Complexity: FETs Equivalent Gates Pb-Free Packages Available*
SOIC-14 SUFFIX CASE 751A HC164AG AWLYWW
TSSOP-14 SUFFIX CASE 948G 164A ALYWG
SOEIAJ-14 SUFFIX CASE Assembly Location Wafer Year Work Week Pb-Free Package Pb-Free Package (Note: Microdot either location) 74HC164A ALYWG
ORDERING INFORMATION
detailed ordering shipping information package dimensions section page this data sheet.
*For additional information Pb-Free strategy soldering details, please download Semiconductor Soldering Mounting Techniques Reference Manual, SOLDERRM/D.
Semiconductor Components Industries, LLC, 2005
May, 2005 Rev.
Publication Order Number: MC74HC164A/D
MC74HC164A
ASSIGNMENT
RESET CLOCK CLOCK SERIAL DATA INPUTS DATA
LOGIC DIAGRAM
PARALLEL DATA OUTPUTS
RESET
FUNCTION TABLE
Inputs Outputs Change Reset Clock
data input data shifted from preceding stage rising edge clock input.
ORDERING INFORMATION
Device MC74HC164AN MC74HC164ANG MC74HC164AD MC74HC164ADG MC74HC164ADR2 MC74HC164ADR2G MC74HC164ADTR2 MC74HC164ADTR2G MC74HC164AFEL MC74HC164AFELG Package PDIP-14 PDIP-14 (Pb-Free) SOIC-14 SOIC-14 (Pb-Free) SOIC-14 SOIC-14 (Pb-Free) TSSOP-14* TSSOP-14* SOEIAJ-14 SOEIAJ-14 (Pb-Free) Shipping Units Rail Units Rail Units Rail Units Rail 2500 Units Reel 2500 Units Reel 2500 Units Reel 2500 Units Reel 2000 Units Reel 2000 Units Reel
information tape reel specifications, including part orientation tape sizes, please refer Tape Reel Packaging Specifications Brochure, BRD8011/D. *This package inherently Pb-Free.
http://onsemi.com
MC74HC164A
MAXIMUM RATINGS
Symbol Parameter Value Unit Supply Voltage (Referenced GND) Input Voltage (Referenced GND) Vout Output Voltage (Referenced GND) Input Current, Iout Output Current, Supply Current, Pins Power Dissipation Still Air, Plastic SOIC Package TSSOP Package Tstg Storage Temperature Lead Temperature, from Case Seconds (Plastic DIP, SOIC TSSOP Package)
This device contains protection circuitry guard against damage high static voltages electric fields. However, precautions must taken avoid applications voltage higher than maximum rated voltages this high-impedance circuit. proper operation, Vout should constrained range (Vin Vout) VCC. Unused inputs must always tied appropriate logic voltage level (e.g., either VCC). Unused outputs must left open.
Maximum ratings those values beyond which device damage occur. Maximum ratings applied device individual stress limit values (not normal operating conditions) valid simultaneously. these limits exceeded, device functional operation implied, damage occur reliability affected. Derating Plastic DIP: mW/_C from 125_C SOIC Package: mW/_C from 125_C TSSOP Package: mW/_C from 125_C high frequency heavy load considerations, Chapter Semiconductor High-Speed CMOS Data Book (DL129/D).
Symbol Parameter Unit Supply Voltage (Referenced GND) Vin, Vout Input Voltage, Output Voltage (Referenced GND) Operating Temperature, Package Types Input Rise Fall Time (Figure 1000
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit 85_C 3.15 1.35
Symbol
Parameter
Test Conditions
-55_C 25_C 3.15 1.35
125_C 3.15 1.35
Unit
Minimum High-Level Input Voltage
Vout |Iout|
Maximum Low-Level Input Voltage
Vout |Iout|
Minimum High-Level Output Voltage
|Iout|
|Iout| |Iout| |Iout|
2.48 3.98 5.48
2.34 3.84 5.34
2.20 3.70 5.20
http://onsemi.com
MC74HC164A
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit 85_C Symbol Parameter Test Conditions -55_C 25_C 125_C Unit Maximum Low-Level Output Voltage |Iout| |Iout| |Iout| |Iout| 0.26 0.26 0.26 0.33 0.33 0.33 0.40 0.40 0.40 Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package) Iout NOTE: Information typical parametric values found Chapter Semiconductor High-Speed CMOS Data Book (DL129/D).
ELECTRICAL CHARACTERISTICS Input
Guaranteed Limit 85_C Symbol fmax Parameter -55_C 25_C 125_C Unit Maximum Clock Frequency (50% Duty Cycle) (Figures tPLH, tPHL Maximum Propagation Delay, Clock (Figures tPHL Maximum Propagation Delay, Reset (Figures tTLH, tTHL Maximum Output Transition Time, Output (Figures Maximum Input Capacitance NOTES: propagation delays with loads other than Chapter Semiconductor High-Speed CMOS Data Book (DL129/D). Information typical parametric values found Chapter Semiconductor High-Speed CMOS Data Book (DL129/D). Typical 25°C, Power Dissipation Capacitance (Per Package)*
Used determine no-load dynamic power consumption: Semiconductor High-Speed CMOS Data Book (DL129/D).
load considerations, Chapter
http://onsemi.com
NOTE: Information typical parametric values found Chapter Semiconductor High-Speed CMOS Data Book (DL129/D).
TIMING REQUIREMENTS (Input
Symbol
trec
Maximum Input Rise Fall Times (Figure
Minimum Pulse Width, Reset (Figure
Minimum Pulse Width, Clock (Figure
Minimum Recovery Time, Reset Inactive Clock (Figure
Minimum Hold Time, Clock (Figure
Minimum Setup Time, Clock (Figure
Parameter
http://onsemi.com
MC74HC164A
-55_C 25_C 1000 Guaranteed Limit 85_C 1000 125_C 1000 Unit
MC74HC164A
DESCRIPTIONS
INPUTS (Pins
register completely static, allowing clock rates down continuous intermittent mode.
OUTPUTS (Pins
Serial Data Inputs. Data these inputs determine data entered into first stage shift register. high level entered into shift register, both inputs must high, thereby allowing input used data-enable input. When only serial input used, other must connected VCC.
Clock (Pin
Parallel Shift Register Outputs. shifted data presented these outputs true, noninverted, form.
CONTROL INPUT Reset (Pin
Shift Register Clock. positive-going transition this shifts data each stage next stage. shift
Active-Low, Asynchronous Reset Input. voltage applied this input resets internal flip-flops sets Outputs level state.
SWITCHING WAVEFORMS
CLOCK
RESET tPHL trec CLOCK
1/fmax tPLH tPHL
tTLH
tTHL
Figure
Figure
TEST POINT VALID CLOCK OUTPUT *Includes probe capacitance DEVICE UNDER TEST
Figure
Figure Test Circuit
http://onsemi.com
MC74HC164A
EXPANDED LOGIC DIAGRAM
CLOCK
RESET
TIMING DIAGRAM
CLOCK RESET
http://onsemi.com
MC74HC164A
PACKAGE DIMENSIONS
PDIP-14 SUFFIX CASE 646-06 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 0.052 0.095 0.008 0.015 0.115 0.135 0.290 0.310 0.015 0.039 MILLIMETERS 18.16 18.80 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 1.32 2.41 0.20 0.38 2.92 3.43 7.37 7.87 0.38 1.01
SEATING PLANE
0.13 (0.005)
SOIC-14 SUFFIX CASE 751A-03 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSIONS INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.127 (0.005) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. MILLIMETERS 8.55 8.75 3.80 4.00 1.35 1.75 0.35 0.49 0.40 1.25 1.27 0.19 0.25 0.10 0.25 5.80 6.20 0.25 0.50 INCHES 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 0.008 0.009 0.004 0.009 0.228 0.244 0.010 0.019
0.25 (0.010)
SEATING PLANE
0.25 (0.010)
http://onsemi.com
MC74HC164A
PACKAGE DIMENSIONS
TSSOP-14 SUFFIX CASE 948G-01 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION DOES INCLUDE MOLD FLASH, PROTRUSIONS GATE BURRS. MOLD FLASH GATE BURRS SHALL EXCEED 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE INTERLEAD FLASH PROTRUSION. INTERLEAD FLASH PROTRUSION SHALL EXCEED 0.25 (0.010) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.08 (0.003) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. TERMINAL NUMBERS SHOWN REFERENCE ONLY. DIMENSION DETERMINED DATUM PLANE -W-. MILLIMETERS INCHES 4.90 5.10 0.193 0.200 4.30 4.50 0.169 0.177 1.20 0.047 0.05 0.15 0.002 0.006 0.50 0.75 0.020 0.030 0.65 0.026 0.50 0.60 0.020 0.024 0.09 0.20 0.004 0.008 0.09 0.16 0.004 0.006 0.19 0.30 0.007 0.012 0.19 0.25 0.007 0.010 6.40 0.252
0.10 (0.004) 0.15 (0.006)
0.25 (0.010)
IDENT.
DETAIL
0.15 (0.006)
SECTION
0.10 (0.004) SEATING
PLANE
DETAIL
http://onsemi.com
MC74HC164A
PACKAGE DIMENSIONS
SOEIAJ-14 SUFFIX CASE 965-01 ISSUE
DETAIL
VIEW
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSIONS INCLUDE MOLD FLASH PROTRUSIONS MEASURED PARTING LINE. MOLD FLASH PROTRUSIONS SHALL EXCEED 0.15 (0.006) SIDE. TERMINAL NUMBERS SHOWN REFERENCE ONLY. LEAD WIDTH DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.08 (0.003) TOTAL EXCESS LEAD WIDTH DIMENSION MAXIMUM MATERIAL CONDITION. DAMBAR CANNOT LOCATED LOWER RADIUS FOOT. MINIMUM SPACE BETWEEN PROTRUSIONS ADJACENT LEAD 0.46 0.018). MILLIMETERS 2.05 0.05 0.20 0.35 0.50 0.18 0.27 9.90 10.50 5.10 5.45 1.27 7.40 8.20 0.50 0.85 1.10 1.50 0.70 0.90 1.42 INCHES 0.081 0.002 0.008 0.014 0.020 0.007 0.011 0.390 0.413 0.201 0.215 0.050 0.291 0.323 0.020 0.033 0.043 0.059 0.028 0.035 0.056
0.13 (0.005)
0.10 (0.004)
Semiconductor registered trademarks Semiconductor Components Industries, (SCILLC). SCILLC reserves right make changes without further notice products herein. SCILLC makes warranty, representation guarantee regarding suitability products particular purpose, does SCILLC assume liability arising application product circuit, specifically disclaims liability, including without limitation special, consequential incidental damages. "Typical" parameters which provided SCILLC data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. SCILLC does convey license under patent rights rights others. SCILLC products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure SCILLC product could create situation where personal injury death occur. Should Buyer purchase SCILLC products such unintended unauthorized application, Buyer shall indemnify hold SCILLC officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that SCILLC negligent regarding design manufacture part. SCILLC Equal Opportunity/Affirmative Action Employer. This literature subject applicable copyright laws resale manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT: Literature Distribution Center Semiconductor P.O. 61312, Phoenix, Arizona 85082-1312 Phone: 480-829-7710 800-344-3860 Toll Free USA/Canada Fax: 480-829-7709 800-344-3867 Toll Free USA/Canada Email: orderlit@onsemi.com American Technical Support: 800-282-9855 Toll Free USA/Canada Japan: Semiconductor, Japan Customer Focus Center 2-9-1 Kamimeguro, Meguro-ku, Tokyo, Japan 153-0051 Phone: 81-3-5773-3850 Semiconductor Website: http://onsemi.com Order Literature: http://www.onsemi.com/litorder additional information, please contact your local Sales Representative.
http://onsemi.com
MC74HC164A/D
Other recent searches
S2062 - S2062 S2062 Datasheet
PS9513 - PS9513 PS9513 Datasheet
PS9513L1 - PS9513L1 PS9513L1 Datasheet
PS9513L2 - PS9513L2 PS9513L2 Datasheet
PS9513L3 - PS9513L3 PS9513L3 Datasheet
MAX1407 - MAX1407 MAX1407 Datasheet
EL38 - EL38 EL38 Datasheet
3X7683 - 3X7683 3X7683 Datasheet
3X7748 - 3X7748 3X7748 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
