3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH 3-STATE
|
|
|
Top Searches for this datasheet
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP WITH 3-STATE OUTPUTS BUS-HOLD
MICRON CMOS Technology Typical tSK(o) (Output Skew) 250ps 2000V MIL-STD-883, Method 3015; 200V using machine model 200pF, 3.3V 0.3V, Normal Range 2.7V 3.6V, Extended Range 2.5V 0.2V CMOS power levels (0.4µ typ. static) Rail-to-Rail output swing increased noise margin Available QSOP, SOIC, SSOP, TSSOP packages
IDT74ALVCH374
FEATURES:
DESCRIPTION:
DRIVE FEATURES:
High Output Drivers: ±24mA Suitable Heavy Loads
APPLICATIONS:
3.3V high speed systems 3.3V lower voltage computing systems
This octal postive edge-triggered D-type flip-flop built using advanced dual metal CMOS technology. ALVCH374 device particularly suitable implementing buffer registers, ports, bidirectional drivers, working registers. positive transition clock (CLK) input, outputs logic levels data inputs. buffered output-enable (OE) input used place eight outputs either normal logic state (high logic levels) high-impedance state. high-impedance state, outputs neither load drive lines significantly. high-impedance state increased drive provide capability drive lines without interface pullup components. does affect internal operations latch. data retained data entered while outputs high-impedance state. ALVCH374 been designed with ±24mA output driver. This driver capable driving moderate heavy load while maintaining speed performance. ALVCH374 "bus-hold" which retains inputs' last state whenever input goes high impedance. This prevents floating inputs eliminates need pull-up/down resistors.
FUNCTIONAL BLOCK DIAGRAM
SEVEN OTHER CHANNELS
logo registered trademark Integrated Device Technology, Inc.
©1999 Integrated Device Technology, Inc.
MARCH 1999
DSC-4473/1
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
CONFIGURATION
ABSOLUTE MAXIMUM RATINGS(1)
Symbol VTERM(2) VTERM(3) TSTG IOUT Description Terminal Voltage with Respect Terminal Voltage with Respect Storage Temperature Output Current Continuous Clamp Current, Continuous Clamp Current, Continuous Current through each -0.5 +4.6 -0.5 VCC+0.5 +150 ±100
Unit
NOTES: Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS cause permanent damage device. This stress rating only functional operation device these other conditions above those indicated operational sections this specification implied. Exposure absolute maximum rating conditions extended periods affect reliability. terminals. terminals except VCC.
CAPACITANCE +25°C, 1.0MHz)
QSOP/ SOIC/ SSOP/ TSSOP TOPVIEW
Symbol COUT CI/O Parameter(1) Input Capacitance Output Capacitance Port Capacitance Conditions VOUT Typ. Max. Unit
NOTE: applicable device type.
DESCRIPTION
Names Clock Input Data Inputs(1) 3-State Outputs Description 3-State Output Enable Input (Active LOW)
NOTE: These pins have "Bus-Hold". other pins standard inputs, outputs, I/Os.
FUNCTION TABLE(1)
Inputs Output Q(2)
NOTES: HIGH Voltage Level Voltage Level Don't Care High Impedance LOW-to-HIGH Transition Output level before indicated steady-state conditions were established.
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified: Operating Condition: -40°C +85°C
Symbol IOZH IOZL ICCL ICCH ICCZ Parameter Input HIGH Voltage Level Input Voltage Level Input HIGH Current Input Current High Impedance Output Current (3-State Output pins) Clamp Diode Voltage Input Hysteresis Quiescent Power Supply Current 2.3V, -18mA 3.3V 3.6V input 0.6V, other inputs 2.3V 2.7V 2.7V 3.6V 2.3V 2.7V 2.7V 3.6V 3.6V 3.6V 3.6V Test Conditions Min. Typ.(1) -0.7 Max. -1.2 Unit
Quiescent Power Supply Current Variation
NOTE: Typical values 3.3V, +25°C ambient.
BUS-HOLD CHARACTERISTICS
Symbol IBHH IBHL IBHH IBHL IBHHO IBHLO
NOTES: Pins with Bus-Hold identified description. Typical values 3.3V, +25°C ambient.
Parameter(1) Bus-Hold Input Sustain Current Bus-Hold Input Sustain Current Bus-Hold Input Overdrive Current 2.3V 3.6V
Test Conditions 0.8V 1.7V 0.7V 3.6V
Min.
Typ.(2)
Max. ±500
Unit
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
OUTPUT DRIVE CHARACTERISTICS
Symbol Parameter Output HIGH Voltage 2.3V 2.3V 2.7V Output Voltage 2.3V 3.6V 2.3V 2.7V 24mA 0.1mA 12mA 12mA 24mA Test Conditions(1) 2.3V 3.6V 0.1mA 12mA Min. Max. 0.55 Unit
NOTE: must within min. max. range shown ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table appropriate range. 40°C 85°C.
OPERATING CHARACTERISTICS, 25°C
2.5V 0.2V Symbol Parameter Power Dissipation Capacitance Outputs enabled Power Dissipation Capacitance Outputs disabled Test Conditions 0pF, 10Mhz Typical 3.3V 0.3V Typical Unit
SWITCHING CHARACTERISTICS(1)
2.5V 0.2V Symbol tPLH tPHL tPZH tPZL tPHZ tPLZ tSK(O) Parameter Propagation Delay Output Enable Time Output Disable Time Pulse Duration, HIGH Setup Time, data before Hold Time, data after Output Skew(2) Min. Max. 2.7V Min. Max. 3.3V 0.3V Min. Max. Unit
NOTES: TEST CIRCUITS WAVEFORMS. 40°C 85°C. Skew between outputs same package switching same direction.
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
TEST CIRCUITS WAVEFORMS TEST CONDITIONS
Symbol VLOAD VCC(1)= 3.3V±0.3V VCC(1)= 2.7V VCC(2)= 2.5V±0.2V Unit
SAME PHASE INPUT TRANSITION tPLH OUTPUT tPLH OPPOSITE PHASE INPUT TRANSITION tPHL tPHL
ALVC Link
Propagation Delay
DISABLE
Pulse(1, Generator D.U.T.
ALVC Link
VLOAD Open VOUT CONTROL INPUT tPZL OUTPUT SWITCH NORMALLY CLOSED tPZH OUTPUT SWITCH NORMALLY OPEN HIGH VLOAD/2 tPHZ tPLZ ENABLE VLOAD/2
ALVC Link
Test Circuit Outputs
DEFINITIONS: Load capacitance: includes probe capacitance. Termination resistance: should equal ZOUT Pulse Generator. NOTES: Pulse Generator Pulses: Rate 10MHz; 2.5ns; 2.5ns. Pulse Generator Pulses: Rate 10MHz; 2ns; 2ns.
Enable Disable Times
SWITCH POSITION
Test Open Drain Disable Enable Disable High Enable High Other Tests Switch VLOAD Open
DATA INPUT TIMING INPUT ASYNCHRONOUS CONTROL SYNCHRONOUS CONTROL
tREM
ALVC Link
Set-up, Hold, Release Times
INPUT
tPLH1
tPHL1
OUTPUT
LOW-HIGH-LOW PULSE HIGH-LOW-HIGH PULSE
OUTPUT tPLH2 tPHL2
ALVC Link
Pulse Width
ALVC Link
tSK(x) tPLH2 tPLH1 tPHL2 tPHL1
Output Skew tSK(X)
NOTES: tSK(o) OUTPUT1 OUTPUT2 outputs. tSK(b) OUTPUT1 OUTPUT2 same bank.
IDT74ALVCH374 3.3V CMOS OCTAL POSITIVE EDGE-TRIGGERED D-TYPE FLIP-FLOP
ORDERING INFORMATION
ALVC Bus-Hold Temp. Range Device Type Package
Small Outline Shrink Small Outline Package Quarter-size Small Outline Package Thin Shrink Small Outline Package Octal Positive Edge-Triggered D-Type Flip-Flop with 3-State Outputs, ±24mA Bus-Hold -40°C +85°C
CORPORATE HEADQUARTERS 2975 Stender Santa Clara, 95054
SALES: 800-345-7015 408-727-6116 fax: 408-492-8674 www.idt.com
Tech Support: logichelp@idt.com (408) 654-6459
Other recent searches
Si7758DP - Si7758DP Si7758DP Datasheet
HV9971 - HV9971 HV9971 Datasheet
G1A060000 - G1A060000 G1A060000 Datasheet
EPC3005 - EPC3005 EPC3005 Datasheet
AFE8406 - AFE8406 AFE8406 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
