Kbit (64K Voltage EPROM EPROM 3.6V SUPPLY VOLTAGE READ OPERATION

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Kbit (64K Voltage EPROM EPROM 3.6V SUPPLY VOLTAGE READ OPERATION

Datasheet Thumbnail

Top Searches for this datasheet

M27W512
Kbit (64K Voltage EPROM EPROM
3.6V SUPPLY VOLTAGE READ OPERATION ACCESS TIME: 70ns 3.6V 80ns 3.6V COMPATIBLE with M27C512 POWER CONSUMPTION: 15µA Standby Current 15mA Active Current 5MHz PROGRAMMING TIME 100µs/byte HIGH RELIABILITY CMOS TECHNOLOGY 2000V Protection 200mA Latchup Protection Immunity ELECTRONIC SIGNATURE Manufacturer Code: Device Code: PACKAGES Lead-Free Versions
Figure Packages
FDIP28W
PDIP28
PLCC32
TSOP28 13.4
November 2004
1/21
M27W512
TABLE CONTENTS
FEATURES SUMMARY Figure Packages SUMMARY DESCRIPTION Figure Table Figure Figure Figure Logic Diagram Signal Names Connections Connections. TSOP Connections
DEVICE OPERATION Read Mode Standby Mode Table Operating Modes Table Electronic Signature. Line Output Control System Considerations. Figure Programming Flowchart. Programming PRESTO Programming Algorithm Program Inhibit Program Verify Electronic Signature ERASURE OPERATION (APPLIES EPROM) MAXIMUM RATING. Table Absolute Maximum Ratings PARAMETERS. Table Measurement Conditions. Figure Testing Input Output Waveform. Figure Testing Load Circuit. Table Capacitance. Table Read Mode Characteristics Table Read Mode Characteristics Figure Read Mode Waveforms Table Programming Mode Characteristics Table Margin Mode Characteristics Figure 10.Margin Mode Waveforms Table Programming Mode Characteristics Figure 11.Programming Verify Modes Waveforms. PACKAGE MECHANICAL
2/21
M27W512
Figure 12.FDIP28W Ceramic Frit-seal DIP, with window, Package Outline. Table FDIP28W Ceramic Frit-seal DIP, with window, Package Mechanical Data Figure 13.PDIP28 Plastic DIP, mils width, Package Outline Table PDIP28 Plastic DIP, mils width, Package Mechanical Data Figure 14.PLCC32 lead Plastic Leaded Chip Carrier, Package Outline Table PLCC32 lead Plastic Leaded Chip Carrier, Package Mechanical Data Figure 15.TSOP28 lead Plastic Thin Small Outline, 13.4 Package Outline Table TSOP28 lead Plastic Thin Small Outline, 13.4 Package Mechanical Data PART NUMBERING Table Ordering Information Scheme REVISION HISTORY Table Revision History.
3/21
M27W512
SUMMARY DESCRIPTION
M27W512 voltage Kbit EPROM offered range (ultra violet erase) (one time programmable). ideally suited microprocessor systems organized 65536 bits. M27W512 operates read mode with supply voltage 2.7V 85°C temperature range. decrease operating power allows either reduction size battery increase time between battery recharges. FDIP28W (window ceramic frit-seal package) transparent which allows user expose chip ultraviolet light erase pattern. pattern then written device following programming procedure. applications where content programmed only time erasure required, M27W512 offered PDIP28, PLCC32 TSOP28 13.4 packages. addition standard versions, packages also available Lead-free versions, compliance with JEDEC J-STD-020B, ECOPACK 7191395 Specification, RoHS (Restriction Hazardous Substances) directive. Figure Logic Diagram
A0-A15
Q0-Q7
GVPP
M27W512
AI01584
Table Signal Names
A0-A15 Q0-Q7 GVPP Address Inputs Data Outputs Chip Enable Output Enable Program Supply Supply Voltage Ground Connected Internally Don't
4/21
M27W512
Figure Connections Figure TSOP Connections
M27W512
AI02679
GVPP
GVPP
M27W512
AI01586
Figure Connections
GVPP M27W512
AI01585
5/21
M27W512
DEVICE OPERATION
modes operations M27W512 listed Operating Modes table. single power supply required read mode. inputs levels except GVPP Electronic Signature. Read Mode M27W512 control functions, both which must logically active order obtain data outputs. Chip Enable power control should used device selection. Output Enable output control should used gate data output pins, independent device selection. Assuming that addresses stable, address access time (tAVQV) equal delay from output Table Operating Modes
Mode Read Output Disable Program Program Inhibit Standby Electronic Signature
Note: VIL, 0.5V.
(tELQV). Data available output after delay tGLQV from falling edge assuming that been addresses have been stable least tAVQV-tGLQV. Standby Mode M27W512 standby mode which reduces supply current from 15mA 15µA with voltage operation 3.6V, Read Mode Characteristics table details. M27W512 placed standby mode applying CMOS high signal input. When standby mode, outputs high impedance state, independent GVPP input.
Pulse
GVPP
Q7-Q0 Data Hi-Z Data Hi-Z Hi-Z Codes
Table Electronic Signature
Identifier Manufacturer's Code Device Code Data
Line Output Control Because EPROMs usually used larger memory arrays, product features line control function which accommodates multiple memory connection. line control function allows: lowest possible memory power dissipation, complete assurance that output contention will occur. most efficient these control lines, should decoded used primary device selecting function, while should made common connection devices array connected READ line from system control bus. This ensures that deselected memory devices their power standby
mode that output pins only active when data required from particular memory device. System Considerations power switching characteristics Advanced CMOS EPROMs require careful decoupling devices. supply current, ICC, three segments that interest system designer: standby current level, active current level, transient current peaks that produced falling rising edges magnitude transient current peaks dependent capacitive inductive loading device output. associated transient voltage peaks suppressed complying with line output control properly selected decoupling
6/21
M27W512
pacitors. recommended that 0.1µF ceramic capacitor used every device between VSS. This should high frequency capacitor inherent inductance should placed close device possible. addition, 4.7µF bulk electrolytic capacitor should used between every eight devices. bulk capacitor should located near power supply connection point.The purpose bulk capacitor overcome voltage drop caused inductive effects traces. Figure Programming Flowchart state. Data introduced selectively programming '0's into desired locations. Although only '0's will programmed, both '1's '0's present data word. only change `1's exposure ultraviolet light EPROM). M27W512 programming mode when input 12.75V pulsed VIL. data programmed applied bits parallel data output pins. levels required address data inputs TTL. specified 6.25V 0.25V. PRESTO Programming Algorithm PRESTO Programming Algorithm allows whole array programmed with guaranteed margin, typical time seconds. This achieved with STMicroelectronics M27W512 several design innovations described M27W512 datasheet improve programming efficiency provide adequate margin reliability. Before starting programming internal MARGIN MODE circuit must order guarantee that each cell programmed with enough margin. Then sequence 100µs program pulses applied each byte until correct verify occurs (see Figure 6.). overprogram pulses applied since verify MARGIN MODE much higher than 3.6V, provides necessary margin. Program Inhibit Programming multiple M27W512s parallel with different data also easily accomplished. Except like inputs including GVPP parallel M27W512 common. level pulse applied M27W512's input, with 12.75V, will program that M27W512. high level input inhibits other M27W512s from being programmed. Program Verify verify (read) should performed programmed bits determine that they were correctly programmed. verify accomplished with VIL. Data should verified with tELQV after falling edge Electronic Signature Electronic Signature (ES) mode allows reading binary code from EPROM that will identify manufacturer type. This mode intended programming equipment automatically match device programmed with corresponding programming algorithm. mode functional 25°C ambient temperature range that required when programming M27W512. activate mode, programming equipment must force 11.5V 12.5V address line M27W512. identifier bytes then
6.25V, 12.75V MARGIN MODE
100µs Pulse VERIFY Last Addr Addr
FAIL
RESET MARGIN MODE CHECK BYTES 1st: 2nd: 2.7V
AI00738C
Programming M27W512 been designed fully compatible with M27C512 same electronic signature. result M27W512 programmed M27C512 same programming equipment applying 12.75V 6.25V VCC. M27W512 PRESTO Programming Algorithm that drastically reduces programming time. Nevertheless achieve compatibility with programming equipments, PRESTO Programming Algorithm used well. When delivered (and after each `1's erasure EPROM), bits M27W512
7/21
M27W512
quenced from device outputs toggling address line from VIH. other address lines must held during Electronic Signature mode. Byte VIL) represents manufacturer code byte VIH) device identifier code. STMicroelectronics M27W512, these identifier bytes given Table read-out outputs Note that M27W512 M27C512 have same identifier byte.
ERASURE OPERATION (APPLIES EPROM)
erasure characteristics M27W512 such that erasure begins when cells exposed light with wavelengths shorter than approximately 4000 should noted that sunlight some type fluorescent lamps have wavelengths 3000-4000 range. Research shows that constant exposure room level fluorescent lighting could erase typical M27W512 about years, while would take approximately week cause erasure when exposed direct sunlight. M27W512 exposed these types lighting conditions extended periods time, suggested that opaque labels over M27W512 window prevent unintentional erasure. recommended erasure procedure M27W512 exposure short wave ultraviolet light which wavelength 2537 integrated dose (i.e. intensity exposure time) erasure should minimum W-sec/cm2. erasure time with this dosage approximately minutes using ultraviolet lamp with 12000 µW/cm2 power rating. M27W512 should placed within inch) lamp tubes during erasure. Some lamps have filter their tubes which should removed before erasure.
8/21
M27W512
MAXIMUM RATING
Stressing device outside ratings listed Table cause permanent damage device. These stress ratings only, operation device these, other conditions outside those indicated Operating sections Table Absolute Maximum Ratings
Symbol TBIAS TSTG TLEAD Parameter Ambient Operating Temperature Temperature Under Bias Storage Temperature Lead Temperature during Soldering Input Output Voltage (except Supply Voltage Voltage Program Supply Voltage
this specification, implied. Exposure Absolute Maximum Rating conditions extended periods affect device reliability. Refer also STMicroelectronics SURE Program other relevant quality documents.
Value (note 13.5
ECOPACK®
Unit
Note: Compliant with JEDEC J-STD-020B (for small body, Sn-Pb assermbly), 7191395 specification, European directive Restrictions Hazardous Substances (RoHS) 2002/95/EU. Minimum voltage Input Output -0.5V with possible undershoot -2.0V period less than 20ns. Maximum voltage Output +0.5V with possible overshoot period less than 20ns. Depends range.
9/21
M27W512
PARAMETERS
This section summarizes operating measurement conditions, characteristics device. parameters Characteristic tables that follow derived from tests performed under MeasureTable Measurement Conditions
High Speed Input Rise Fall Times Input Pulse Voltages Input Output Timing Ref. Voltages 10ns 1.5V Standard 20ns 0.4V 2.4V 0.8V
ment Conditions summarized relevant tables. Designers should check that operating conditions their circuit match measurement conditions when relying quoted parameters.
Figure Testing Input Output Waveform
Figure Testing Load Circuit
1.3V
High Speed 1.5V DEVICE UNDER TEST 2.0V 0.8V
AI01822
1N914
3.3k
Standard 2.4V
0.4V
30pF High Speed 100pF Standard includes capacitance
AI01823B
Table Capacitance
Symbol COUT Parameter Input Capacitance Output Capacitance Test Condition (1,2) VOUT Unit
Note: 25°C, 1MHz Sampled only, 100% tested.
10/21
M27W512
Table Read Mode Characteristics
Symbol ICC1 ICC2 Parameter Input Leakage Current Output Leakage Current Supply Current Supply Current (Standby) Supply Current (Standby) CMOS Program Current Input Voltage Input High Voltage Output Voltage Output High Voltage 2.1mA -1mA Test Condition VOUT VIL, VIL, IOUT 0mA, 5MHz 3.6V 0.2V, 3.6V -0.6 Unit
Note: must applied simultaneously with before removed simultaneously after VPP. Maximum voltage Output +0.5V.
Table Read Mode Characteristics
M27W512 Test Condition
3.6V 3.6V
Symbol
Parameter
-100 (-120/-150/-200)
3.6V
Unit
tAVQV tELQV tGLQV tEHQZ tGHQZ tAXQX tACC Address Valid Output Valid Chip Enable Output Valid Output Enable Output Valid Chip Enable High Output Hi-Z Output Enable High Output Hi-Z Address Transition Output Transition VIL, VIL,
Note: must applied simultaneously with before removed simultaneously after VPP. Sampled only, 100% tested. Speed obtained with High Speed measurement conditions.
11/21
M27W512
Figure Read Mode Waveforms
A0-A15
VALID tAVQV tAXQX
VALID
tGLQV tELQV Q0-Q7 tGHQZ Hi-Z tEHQZ
AI00735B
Table Programming Mode Characteristics
Symbol Parameter Input Leakage Current Supply Current Program Current Input Voltage Input High Voltage Output Voltage Output High Voltage Voltage 2.1mA -1mA 11.5 12.5 -0.3 Test Condition (1,2) Unit
Note: 6.25V 0.25V; 12.75V 0.25V must applied simultaneously with before removed simultaneously after VPP.
12/21
M27W512
Table Margin Mode Characteristics
Symbol tA9HVPH tVPHEL tA10HEH tA10LEH tEXA10X tEXVPX tVPXA9X tAS9 tVPS tAS10 tAS10 tAH10 tVPH tAH9 Parameter High High High Chip Enable VA10 High Chip Enable High (Set) VA10 Chip Enable High (Reset) Chip Enable Transition VA10 Transition Chip Enable Transition Transition Transition Transition Test Condition (1,2) Unit
Note: 6.25V 0.25V; 12.75V 0.25V must applied simultaneously with before removed simultaneously after VPP.
Figure Margin Mode Waveforms
tA9HVPH GVPP tVPHEL tA10HEH tEXA10X tEXVPX tVPXA9X
Reset tA10LEH
AI00736B
Note: High level High level 12V.
13/21
M27W512
Table Programming Mode Characteristics
Symbol tAVEL tQVEL tVCHEL tVPHEL tVPLVPH tELEH tEHQX tEHVPX tVPLEL tELQV tEHQZ tEHAX tVCS tOES tPRT tOEH tDFP Parameter Address Valid Chip Enable Input Valid Chip Enable High Chip Enable High Chip Enable Rise Time Chip Enable Program Pulse Width (Initial) Chip Enable High Input Transition Chip Enable High Transition Chip Enable Chip Enable Output Valid Chip Enable High Output Hi-Z Chip Enable High Address Transition Test Condition (1,2) Unit
Note: 6.25V 0.25V; 12.75V 0.25V must applied simultaneously with before removed simultaneously after VPP. Sampled only, 100% tested.
Figure Programming Verify Modes Waveforms
A0-A15 tAVEL Q0-Q7 tQVEL tVCHEL GVPP tVPHEL tELEH PROGRAM DATA
VALID tEHAX DATA tEHQX tELQV tEHVPX tEHQZ
tVPLEL
VERIFY
AI00737
14/21
M27W512
PACKAGE MECHANICAL
Figure FDIP28W Ceramic Frit-seal DIP, with window, Package Outline
FDIPW-a
Note: Drawing scale.
Table FDIP28W Ceramic Frit-seal DIP, with window, Package Mechanical Data
Symbol 7.11 2.54 14.99 33.02 15.24 1.45 0.51 3.91 3.89 0.41 0.23 36.50 13.06 16.18 3.18 1.52 millimeters 5.72 1.40 4.57 4.50 0.56 0.30 37.34 13.36 18.03 4.10 2.49 0.280 0.100 0.590 1.300 0.600 0.057 0.020 0.154 0.153 0.016 0.009 1.437 0.514 0.637 0.125 0.060 inches 0.225 0.055 0.180 0.177 0.022 0.012 1.470 0.526 0.710 0.161 0.098
15/21
M27W512
Figure PDIP28 Plastic DIP, mils width, Package Outline
PDIP
Note: Drawing scale.
Table PDIP28 Plastic DIP, mils width, Package Mechanical Data
millimeters Symbol 3.300 1.78 2.08 36.830 33.020 15.240 13.720 2.540 15.000 12.700 14.800 15.200 14.480 15.200 16.680 0.1299 0.070 0.082 4.445 0.630 3.810 0.450 1.270 0.230 36.580 0.310 37.080 1.4500 1.3000 0.6000 0.5402 0.1000 0.5906 0.5000 0.5827 0.5984 0.5701 0.5984 0.6567 3.050 4.570 0.1750 0.0248 0.1500 0.0177 0.0500 0.0091 1.4402 0.0122 1.4598 0.1201 0.1799 inches
16/21
M27W512
Figure PLCC32 lead Plastic Leaded Chip Carrier, Package Outline
0.51 (.020) 1.14 (.045)
PLCC-A
Note: Drawing scale.
Table PLCC32 lead Plastic Leaded Chip Carrier, Package Mechanical Data
Symbol 0.89 10.16 1.27 7.62 12.32 11.35 4.78 14.86 13.89 6.05 0.00 millimeters 3.18 1.53 0.38 0.33 0.66 3.56 2.41 0.53 0.81 0.10 12.57 11.51 5.66 15.11 14.05 6.93 0.13 0.035 0.400 0.050 0.300 0.485 0.447 0.188 0.585 0.547 0.238 0.000 inches 0.125 0.060 0.015 0.013 0.026 0.140 0.095 0.021 0.032 0.004 0.495 0.453 0.223 0.595 0.553 0.273 0.005
17/21
M27W512
Figure TSOP28 lead Plastic Thin Small Outline, 13.4 Package Outline
TSOP-a
Note: Drawing scale
Table TSOP28 lead Plastic Thin Small Outline, 13.4 Package Mechanical Data
millimeters Symbol 0.550 13.200 11.700 7.900 0.500 0.950 0.170 0.100 1.250 0.200 1.150 0.270 0.210 0.100 13.600 11.900 8.100 0.700 0.0217 0.5197 0.4606 0.3110 0.0197 0.0374 0.0067 0.0039 inches 0.0492 0.0079 0.0453 0.0106 0.0083 0.0039 0.5354 0.4685 0.3189 0.0276
18/21
M27W512
PART NUMBERING
Table Ordering Information Scheme
Example: Device Type Supply Voltage 2.7V 3.6V Device Function Kbit (64Kb Speed (1,2) -100 Design -120 -150 -200 Package FDIP28W PDIP28 PLCC32 TSOP28: 13.4 Temperature Range Options Blank Standard Packing Tape Reel Packing Lead-free RoHS Package, Standard Packing Lead-free RoHS Package, Tape Reel Packing
Note: High Speed, Characteristics section further information. This speed also guarantees 70ns access time 3.0V 3.6V. These speeds replaced 100ns. Packages option available request. Please contact STMicroelectronics local Sales Office.
M27W512
list available options (speed, package, etc.) further information aspect this
device, please contact your nearest Sales Office.
19/21
M27W512
REVISION HISTORY
Table Revision History
Date Version Revision Details FDIP28W Package Dimension, added (Table 12.) TSOP32 Package Dimension changed (Table 15.) 70°C Temperature Range deleted Speed Classes changed Typing error (Table Package mechanical data clarified FDIP28W (Table 12.), PDIP28 (Table 13.), PLCC32 (Table 14., Figure 14.) TSOP28 (Table 15., Figure 15.) Details ECOPACK lead-free package options added
20-Mar-2000
15-Jun-2001 30-Aug-2002 08-Nov-2004
20/21
M27W512
Information furnished believed accurate reliable. However, STMicroelectronics assumes responsibility consequences such information infringement patents other rights third parties which result from use. license granted implication otherwise under patent patent rights STMicroelectronics. Specifications mentioned this publication subject change without notice. This publication supersedes replaces information previously supplied. STMicroelectronics products authorized critical components life support devices systems without express written approval STMicroelectronics. logo registered trademark STMicroelectronics. other names property their respective owners 2004 STMicroelectronics rights reserved STMicroelectronics group companies Australia Belgium Brazil Canada China Czech Republic Finland France Germany Hong Kong India Israel Italy Japan Malaysia Malta Morocco Singapore Spain Sweden Switzerland United Kingdom United States America www.st.com
21/21

Kbit (64K Voltage EPROM EPROM 3.6V SUPPLY VOLTAGE READ OPERATION

Top Searches for this datasheet

Other recent searches