INCH IMAGE SENSOR NTSC CAMERA KC75118C interline transfer area im

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

INCH IMAGE SENSOR NTSC CAMERA KC75118C interline transfer area im

Datasheet Thumbnail

Top Searches for this datasheet

KC75118C
INCH IMAGE SENSOR NTSC CAMERA
KC75118C interline transfer area image sensor developed NTSC inch optical format cameras, object detector image pattern recognizer. High sensitivity achieved through adoption complementary color mosaic filter, on-chip micro lenses. This chip features field integration read system electronic shutter with variable charge storage time.
14Pin
FEATURES
Optical Size inch Format On-chip Complementary Color Mosaic Filter Variable Speed Electronic Shutter (1/60, 1/100 1/10, 000sec) Horizontal Register 3.3V Drive 14pin Ceramic Package Adjust Substrate Bias Field Integration Read System Bias Reset Gate
ORDERING INFORMATION
Device KC75118C Package 14Pin Operating
STRUCTURE
Number Total Pixels: Number Effective Pixels: Chip Size: Unit Pixel Size: Optical Blacks Dummies: 381(H) 506(V) 362(H) 492(V) 3.75mm(H) 3.30mm(V) 8.10µm(H) 4.45µm(V) Refer Figure Below Vertical Line (Even Field Only)
Dummy Pixels Optical Black Pixels
Effective Imaging Area
OUTPUT
V-CCD
Effective Pixels
H-CCD
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
BLOCK DIAGRAM
(Top View)
VOUT
Vertical Shift Register
Vertical Shift Register
Vertical Shift Register
Vertical Shift Register
Horizontal Shift Register
Figure Block Diagram
DESCRIPTION
Table Description Symbol VOUT Description Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock Vertical register transfer clock connection Ground Signal output Symbol Description Output stage drain bias Ground Substrate clock Protection circuit bias Reset gate clock Horizontal transfer clock Horizontal transfer clock
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
ABSOLUTE MAXIMUM RATINGS (NOTE)
Table Absolute Maximum Ratings Characteristics Substrate voltage Vertical clock input voltage Horizontal clock input voltage Voltage difference between vertical horizontal clock input pins Output clock input voltage Protection circuit bias voltage Operating temperature Storage temperature TSTG Symbols Min. -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 -0.3 Max. Unit
NOTE: device destroyed, applied voltage temperature higher than absolute maximum rating voltage temperature.
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
CHARACTERISTICS
Table Characteristics Item Output stage drain bias Reset gate voltage adjustment range Protection circuit bias voltage Output stage drain current Symbol VRGL Min. 14.55 Typ. 15.0 Max. 15.45 Unit Remar
lowest vertical clock level
CLOCK VOLTAGE CONDITIONS
Table Clock Voltage Conditions Item Read-out clock voltage Vertical transfer clock voltage Symbol VVM1 VVM4 VVL1 VVL4 Horizontal transfer clock voltage Charge reset clock voltage VRGLH VRGLL Substrate clock voltage VSUB 21.5 22.5 Min. 14.55 -0.05 -8.5 -0.05 4.75 Typ. 15.0 -8.0 Max. 15.45 0.05 -7.5 5.25 0.05 5.25 23.5 Unit Remark High level (VVH1+V VH2)/2 (VVH1+V VH2)/2 High High Shutter
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
DRIVE CLOCK WAVEFORM CONDITIONS
Read Clock Waveform
100%
VVH3
Vertical Transfer Clock Waveform
VVH1
VVHH VVHL
VVHH VVHL
=1~4)
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
Horizontal Transfer Clock Waveform Diagram
Reset Gate Clock Waveform Diagram
Point waveform VRGLH VRGLL VRGL 0.5V VRGL
waveform
VRGLH maximum value VRGLL minimum value coupling waveform period from Point diagram about rise VRGL (VRGLH VRGLL)/2, VFRG VRGH VRGL
Substrate Clock Waveform
100%
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
CLOCK EQUIVALENT CIRCUIT CONSTANT
Table Clock Equivalent Circuit Constant
Item Read-out clock Vertical clock Symbol Min. Horizontal clock Reset clock Substrate clock Typ. Max. Min. Typ. Max. Min. Typ. Max. Min. Typ. Max. Unit
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
EQUIVALENT CIRCUIT PARAMETERS
Table Equivalent Circuit Parameters Item Capacitance between vertical transfer clock Symbol Capacitance between vertical transfer clocks CV12, CV34 CV23, CV41 CV13 CV24 Capacitance between horizontal transfer clock Capacitance between horizontal transfer clocks Capacitance between substrate clock Vertical transfer clock serial resistor Vertical transfer clock ground resistor Horizontal transfer clock serial resistor Reset gate clock serial resistor CH1, CH12 CSUB RVGND RH1, Typ. 1120 Unit Remark
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
OPERATING CHARACTERISTICS
Device Temperature Table Operating Characteristics Item Sensitivity Saturation signal Smear Blooming margin Uniformity Dark signal (NOTE) Dark shading (NOTE) Image Flicker Flicker red, blue Color uniformity Line stripe Symbol YSAT YLAG FCR, DSR, LCW, LCR, LCG, 1,000 Min. 0.007 0.01 Typ. Max. Unit mV/lux times Remark
NOTE: Test Temperature
TESTING SYSTEM
Signal Output
(3dB down 4MHz) LPF1 Illuminance Signal Output
Chroma Signal Output
LPF2
(3dB down 1MHz)
Figure Testing System
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
TEST CONDITION
light source with color temperature 3,200K hallogen lamp CM-500S filter. light source adjusted accordance with average value signals indicated each item.
COLOR FILTER ARRAY
color filter array this image sensor shown right figure. this complementary mosaic used with operation field integration mode, where photosensors read during each video field. signals from vertically-adjacent photosensor lines, such line couple field summed when signal charges transferred into vertical transfer column. read line pairing shifted down line field sensor output signals through horizontal register (H-CCD) line [G+Cy], [MG+Ye], [G+CY], [Mg+Ye]. These signals processed order compose signals. adding adjacent signals line signal formed follows
signal composed substracting adjacent signals line
Figure Color Filter Array
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
Next, signals through H-CCD line [Mg+Cy], [G+Ye], [Mg+Cy], [G+Ye]. Simmilary, signals composed line follows
Accordingly, signal balanced relation scanning lines, signal takes form -(B-Y) alternate lines. same field.
TEST METHODS
Measure light intensities when averaged illuminance output value standard illuminance output value, 150mV (YA) when half 150mV (1/2 YA).
Adjust light intensity times that signal output average value 150mV) then test signal minimum value YSAT).
Adjust light intensity times that signal output average value 150mV), then remove readout clock drain signal photosensors electronic shutter operation respective horizontal blanking times with other clocks unchanged. Measure maximum illuminance output value (YSM).
Adjust light intensity 1,000 times value with which then inspect whether there blooming phenomenon not.
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
Measure maximum minimum illuminance output value (YMAX, YMIN) when light intensity adjusted make
Measure with horizontal idling time transfer level reference, when device ambient temperature light sources shielded.
Follow test method measure maximum (DMAX) minimum illuminance output (DMIN).
Adjust light intensity signal output value strobe light 150mV (YA), calculate below formula with measuring image signal which qenerated below timing diagram.
YLAG
Light Strobe Timing Signal Output 150mV
YLag
Output
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
Adjust light intensity signal average value 150mV (YA), calculate below formula with measuring signal differences [mV]) between fields.
Adjust light intensity make using blue optical filters respectively, measure differences (CR, between chroma signal values even fields averaged chroma signal values (CR, CB).
where
Adjust light intensity make using blue optical filters respectively, measure minimum (CR,MIN CB,MIN) maximum R,MAX B,MAX) chroma signal values.
where
Adjust light intensity make 150mV(YL) using white filter, (R), green blue optical filters respectively, measure illuminance signal difference values (YLW, YLR, YLG, YLB) between illuminance signal lines same field.
where
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
SPECTRAL RESPONSE CHARACTERISTICS
Excluding Light Source Characteristics
Spectral Response (nsec) Spectral Response NORMALIZED RESPONSE Cyan Green WAVE LENGTH(nm) Wave Length (nm) Figure Spectral Response Characteristics Magenta Yellow
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
APPLICATION CIRCUITS
-7.5V
10µ/16V
3.9K 2SK1070
MA110 10µ/16V
VOUT
100K 1µ/35V
KC75118C
KS7221D
10µ/16V
XSUB XSG1 XSG2
Figure Application Circuits
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
READ-OUT CLOCK TIMING CHART
Unit: [µs]
Field
38.1
Even Field
Figure Read-out Clock Timing Chart
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
CLOCK TIMING CHART (VERTICAL SYNC.)
490492
CLP1
Figure Clock Timing Chart (Vertical Sync.)
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
CLOCK TIMING CHART (HORIZONTAL SYNC.)
CLP1
Figure Clock Timing Chart (Horizontal Sync.)
KC75118C
INCH IMAGE SENSOR NTSC CAMERA
PACKAGE DIMENSIONS
(Unit Glass 7583 Ceramicframe 90%Min. (black) 0.38 Ceramic Base 90%Min. (black) Lead Frame Alloy Inner Outer 0.50 (L/F 0.25 0.30
2.50 (L/F R0.70 4-R0.50 2.600
NOTES:
Glass (7583)
Max. Leakage Hellium Detector Resistance Between Leads Insulation Resistance
:10-8atm. cc/sec mmHg :Above 100HM :Electrical leakage shall exceed nano 100V
Ceamic Material Lead Frame Coplanarity
:Min. al20 (black)
:0.25 Max. (after attach) :0.076/mm, -0.102/mm
4.13
Planarity clad Thickness
1.27
:5um 10um stamp) :2.5um 12.7um (for etch) :Min. 0.762mm from lead :4um 20um
Thickness Coverage thickness Flatness attach seal area Other
:Max. 0.051mm :Max. 0.051mm according semi standards.
Figure Package Dimensions
INCH IMAGE SENSOR NTSC CAMERA
KC75118C
HANDLING INSTRUCTIONS
Static Charge Prevention image sensors easily damaged static discharge. Before handling, sure take following protective measures. chargeable gloves, clothes material. Also conductive shoes. When handling directly, earth band. Install conductive floor working table prevent generation static electricity. Ionized recommended discharging when handling image sensor. shipment mounted substrates, boxes treated prevention static charges.
Soldering Make sure package temperature does exceed Solder dipping mounting furnace causes damage glass other defects. grounded soldering iron solder each less than seconds. repairs remount, cool sufficiently. dismount imaging device, solder suction equipment. When using electronic disoldering tool, thermal controller zero cross on/off type connect ground
Dust Dirt Protection Operate clean environments (around class 1000 will appropriate). either touch glass plates hand have object come contact with glass surface. Should dirt stick glass surface blow with blow (for dirt stuck through static electricity ionized recommended). Clean with cotton ethyl alcohol glass surface grease stained. caerful scratch glass. Keep case protect from dust dirt. prevent condensation, preheat precool when moving room with great temperature differences. When protective tape applied before shipping, just before remove tape applied electrostatic protection. reuse tape.
expose strong light (sun rays) long period, color filter discolored.
Exposure high temperature humidity will affect characteristics. accordingly avoid storage usage such conditions.
image sensors precise optical equipment that should subject mechanical shocks.

INCH IMAGE SENSOR NTSC CAMERA KC75118C interline transfer area im

Top Searches for this datasheet

Other recent searches