Single-Chip Data Release Form (WG) MDS-894-0010E Customer Na

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Single-Chip Data Release Form (WG) MDS-894-0010E Customer Na

Datasheet Thumbnail

Top Searches for this datasheet

MB89475
Single-Chip Data Release Form (WG)
MDS-894-0010E
Customer Name
Customer Contact
Customer Part
Fujitsu Part
MB89475
Application
History
Release Update Previous: MB89475
Automobile Engine Automobile Non-Engine Non-Automobile
Mask Option Item
Package Type
Contents Selection
SH-DIP-48 LQFP
Notes
Mask Data Start Arbitrary
Address
Media Address
Program Data
Address (Fujitsu Internal use)
Fill above blanks hexadecimal verification. Write program data from Start address address.
Power Reset (POR)
(217/fch)
Page
Mask Option Item
Main Clock Oscillation Type (OSC)
Contents Selection
214/fCh 217/fCh 218/fCh Crystal Resonator Ceramic Resonator Resonator
Notes
Clock Mode (CLK)
Single Clock Dual Clock
Operation Frequency
Clock:
frequency written here regarded guaranteed operating frequency.
Stop Mode
Page
Marking Form
Standard (See below:) Special
Customer Spec
(Operating temperature., Operating supply voltage, Supply current, etc.)
Engineering samples have Standard marking with "ES" mark.
Fujitsu Part
Electrical Spec
Standard Special
Logo JAPAN Country Origin Fujitsu Part Program Code Control Code
Mechanical Spec
Standard Special
MB89475 YYYY ZZZZ
Date Code height Fujitsu Logo 2.0mm. other character except logo gothic font height 1.2mm. Control Date Codes
Quality/Reliability
(Burn-in, Screening. etc.)
Standard Special
alphanumeric characters. Program Code assigned Fujitsu.
Other Special Requirements
(Special marking proposal form etc.)
Page
Single-Chip Data Release Form (F2MC-8L)
Rev.6.1
February 1994
Sample Requirement
Engineering Samples (ES) Free Engineering Samples: (Included mask charge) Quantity Req'd Date (MM/DD/YY) Units
Order Type
Non-Risk Order (ROM verification skipped) Risk Order confirmation skipped.) Notes: Refer next Page
Charged Engineering Sample (Additional Quantity Req'd Date (MM/DD/YY) Samples Price Package Type: Unit Ceramic Plastic Committed (P/O: Units
Application
Sales Price: (Including initial Units Engineering Samples) Committed Issued (P/O:
Production Info.
Production Start: (MM/DD/YY) Initial Production: Units Month Production Rate: Units Month Unit Total Production: Units Life Years) Production End: (MM/DD/YY) Expected Committed Expected: Committed Expected: Committed
Expected
Charged Commercial Samples (CS) Quantity Req'd Date (MM/DD/YY) Samples Price Expected Units
Committed (P/O:
Originated
Signature: Title Date
Production Info.
FMI/FMG/FMAP/FDI: PMM: PME: Scheduler: Kawasaki: Kawasaki:
Fujitsu declares that Fujitsu disclose sell your software mask third party. However, even software from third party completely nearly same with yours, Fujitsu doesn't assume responsibility. that case, whenever find software from concerned third party infringe upon your right, Fujtisu concludes have settle infringement problem with concerned third party. Page
Single-Chip Data Release Form
Rev.7.2 2001
Notice
1.PROGRAM DATA
data format should Intel (except Intel extended hex), Motorola Motorola formats. (Recommended Motorola S1/S2). should have offset address. diskette save program data inch diskette (1.44MB). electrical readable file (plain text) sending through e-mail. program data should filled customer addresses from START ADDRESS ADDRESS. Physical Program contains unused addresses after ADDRESS, remainder unused addresses will filled default Fujitsu Fujitsu will sending back confirmation data Motorola format which processed converted Fujitsu's fabrication use. need simple offset adjustment requires your confirmation.
2.SAMPLES
(Engineering Sample) guaranteed only functional/electrical characteristics. Therefore, should used reliability test. Also, marking form Fujitsu STANDARD unless otherwise requested (Commercial Sample) guaranteed reliability equivalent that production parts.
3.ORDER TYPE
Non-Risk Order Risk Order makes after data release starts production after verification. starts production after code confirmation. confirmation skipped.
4.CHANGING AFTER DATA RELEASE
change required released data, will remake mask from beginning. such case, another mask charge corrected DATA RELEASE FORM necessary.
5.SOFTWARE RIGHT
Fujitsu declares that Fujitsu disclose sell your software mask third party. However, even software from third party completely nearly same with yours, Fujitsu doesn't assume responsibility. that case, whenever find software from concerned third party infringe upon your right, Fujtisu concludes have settle infringement problem with concerned third party.
Page

Single-Chip Data Release Form (WG) MDS-894-0010E Customer Na

Top Searches for this datasheet

Other recent searches