AKD5366VR-A AK5366VR Evaluation Board Rev.1 GENERAL DESCRIPT
|
|
|
Top Searches for this datasheet
[AKD5366VR-A]
AKD5366VR-A
AK5366VR Evaluation Board Rev.1
GENERAL DESCRIPTION AKD5366VR-A evaluation board digital audio 24bit 48kHz converter, AK5366VR. AKD5366VR-A includes input circuit also digital interface transmitter. Further, AKD5366VR-A achieve interface with digital audio systems opt-connector. Ordering guide
AKD5366VR-A AK5366VR Evaluation Board (Cable connecting with printer port IBM-AT, compatible control software packed with this.)
FUNCTION with optical output connector external clock input 10pin Header serial control mode
AVDD,DVDD,TVDD AVSS,DVSS
LIN1-5
RIN1-5
AK5366VR
AK4103 (DIT)
Control Data 10pin Header Clock Generator Data 10pin Header
Figure AKD5366VR-A Block Diagram Circuit diagram layout attached this manual.
<KM083701>
2007/03
[AKD5366VR-A]
Evaluation Board Manual Operation sequence
power supply lines. [AVDD] [TVDD] [D3V] [VCC] [AGND] [DGND] (Red) (Orange) (Orange) (Red) (Black) (Black) 4.75 5.25V (typ. 5.0V, AVDD, TVDD AK5366VR) 5.25V (typ. 3.3V, DVDD AK5366VR) 5.25V (typ. 3.3V, 74LVC541) (for logic circuit digital part) (for analog ground) (for logic ground)
Each supply line should distributed from power supply unit. TVDD must same voltage level. evaluation mode, jumper pins switches. (See followings.) Power AK5366VR AK4103 should reset once bringing upon power-up.
Evaluation mode
Slave Mode When evaluating AK5366VR using AK4103, setting AK5366VR's audio interface format should same AK4103's format. setting AK5366VR (No.1 (I2C) parallel mode, serial mode) should same setting AK4103 (No.1 SW3). About AK5366VR's audio interface format, refer AK5366VR's datasheet. About AK4103's audio interface format, Table3. (1-1) evaluation using function AK4103 PORT1 (DIT) used. generates audio bi-phase signal from received data which output through optical connector (TOTX176). possible connect AKM's converter evaluation boards digital-amplifier which equips input. Nothing should connected PORT2 (ROM). case using external clock through connector (J13), select (CLK) short (XTE) open (EXT).
LRCK BICK
<KM083701>
2007/03
[AKD5366VR-A]
Master Mode (2-1) evaluation using function AK4103 PORT1 (DIT) used. generates audio bi-phase signal from received data which output through optical connector (TOTX176). possible connect AKM's converter evaluation boards digital-amplifier which equips input. Nothing should connected PORT2 (ROM). case using external clock through connector (J13), select (CLK) short (XTE) open (EXT).
LRCK BICK
Other jumper pins
(GND): Analog ground Digital ground OPEN: Separated. SHORT: Common. (The connector "DGND" open.) <Default> (M/S): Select Master/Slave mode AK5366VR SLAVE: Slave mode <Default> MASTER: Master mode (TVDD): Select DVDD AK5366VR REG: Supply from regulator TVDD: Supply from TVDD connector <Default> (MCLK): MCLK Frequency 74HC4040 256: MCLK 256fs. (=12.288MHz@fs=48kHz) <Default> 512: MCLK 512fs. (=24.576MHz@fs=48kHz)
<KM083701>
2007/03
[AKD5366VR-A]
Switch
[SW1] (MODE1): Setting evaluation mode AK5366VR "H", "L". Default "L". Name ("L") ("H") 3-wire Control Control CAD0 Fixed CAD1 Fixed Fixed SEL2 Table SEL1 SEL0 Fixed Table Mode Setting AK5366VR SEL1 SEL0 Input Selector LIN1 RIN1 LIN2 RIN2 LIN3 RIN3 LIN4 RIN4 LIN5 RIN5 Table Input Selector
SEL2
Default
[SW3] (MODE2): Setting evaluation mode AK4103 "H", "L". Default "L". Name ("L") ("H") 24bit, justified 24bit, Compatible CKS1 Table CKS0 Table Mode Setting AK4103 CKS1 CKS0 MCLK 256fs 96kHz 512fs 48kHz 384fs 48kHz Table MCLK Frequency Setting AK4103
Mode
Default
function toggle
Upper-side lower-side "L". [SW2] (PDN): Power down reset AK5366VR AK4103. This should brought once upon power-up. Keep during normal operation. [SW4] (SMUTE): Soft mute AK5366VR. This should brought during soft mute.
<KM083701>
2007/03
[AKD5366VR-A]
Serial Control
AKD5366VR-A controlled printer port (parallel port) IBM-AT compatible Connect PORT3 (CTRL) with 10-line flat cable packed with AKD5366VR-A. control software packed with this evaluation board does support control.
Connect
CCLK CDTI
AKD5366VR-A
wire flat cable
10pin Connector
10pin Header
Figure Connect 10-line flat cable
Analog Input/Output Circuits
Input Circuit Analog inputs AK5366VR input (LIN1), (RIN1), (LIN2), (RIN2), (LIN3), (RIN3), (LIN4), (RIN4), (LIN5) (RIN5).
RIN1 RIN1 LIN1 LIN1
RIN2
RIN2
LIN2
LIN2
RIN3
RIN3
LIN3
LIN3
RIN4
RIN4
LIN4
LIN4
RIN5
RIN5
LIN5
LIN5
Figure LIN1-5/RIN1-5 Input circuits
<KM083701>
2007/03
[AKD5366VR-A]
cut-off frequency input circuit this evaluation board below. When changing cut-off frequency, change constant each resistor capacitor. cut-off frequency front Pre-Amp: 3.4Hz 47k, 1µF) cut-off frequency HPF, which composed input resistance IPGAL/R pins capacitor between Pre-Amp output IPGA input: 3.4Hz. 10k, 4.7µF) Output Circuit Pre-Amp outputs AK5366VR output (LOUT) (ROUT).
LOUT
LOUT
ROUT
Figure LOUT/ROUT Output circuits
assumes responsibility trouble when using circuit examples.
<KM083701>
ROUT
2007/03
[AKD5366VR-A]
Control Software Manual Set-up evaluation board control software
AKD5366VR-A according "Evaluation Board Manual". Connect IBM-AT compatible with AKD5366VR-A 10-line type flat cable (packed with AKD5366VR-A). Take care direction 10pin header. (Please install driver CD-ROM when this control software used Windows 2000/XP. Please refer "Installation Manual Control Software Driver device control software". case Windows95/98/ME, this installation needed. This control software does operate Windows NT.) Insert CD-ROM labeled "AKD5366VR-A Evaluation Kit" into CD-ROM drive. Access CD-ROM drive double-click icon "akd5366vr-a.exe" control program. Please evaluate according following.
Operation flow
Keep following flow. control program according explanation above. Click "Port Reset" button.
Explanation each buttons
[Port Reset]: [Write default]: [All Write]: [Function1]: [Function2]: [Function3]: [Function4]: [Function5]: [SAVE]: [OPEN]: [Write]: interface board (AKDUSBIF-A). Initialize register AK5366VR. Write registers that currently displayed. Dialog write data keyboard operation. Dialog write data keyboard operation. sequence register setting executed. sequence that created [Function3] assigned buttons executed. register setting that created [SAVE] function main window assigned buttons executed. Save current register setting. Write saved values register. Dialog write data mouse operation.
Indication data
Input data indicated register map. letter indicates blue indicates "0". Blank part that defined datasheet.
<KM083701>
2007/03
[AKD5366VR-A]
Explanation each dialog [Write Dialog]: Dialog write data mouse operation
There dialogs corresponding each register. Click [Write] button corresponding each register dialog. check check box, data becomes "1". not, "0". want write input data AK5366VR, click [OK] button. not, click [Cancel] button.
[Function1 Dialog]: Dialog write data keyboard operation
Address Box: Input registers address figures hexadecimal. Data Box: Input registers data figures hexadecimal. want write input data AK5366VR, click [OK] button. not, click [Cancel] button.
[Function2 Dialog]: Dialog evaluate IPGA, DATT
This dialog corresponding address: 04H, 05H, 08H, 09H. Address Box: Start Data Box: Data Box: Interval Box: Step Box: Input registers address figures hexadecimal. Input starts data figures hexadecimal. Input data figures hexadecimal. Data written AK5366VR this interval. Data changes this step.
Mode Select Box: check this check box, data reaches data, returns start data. [Example] Start Data Data Data flow: check this check box, data reaches data, does return start data. [Example] Start Data Data Data flow: want write input data AK5366VR, click [OK] button. not, click [Cancel] button.
<KM083701>
2007/03
[AKD5366VR-A]
[Save] [Open] 4-1. [Save]
Save current register setting data. extension file name "akr".
(Operation flow)
Click [Save] Button. file name push [Save] Button. extension file name "akr". 4-2. [Open] register setting data saved [Save] written AK5366VR. file type same [Save].
(Operation flow)
Click [Open] Button. Select file (*.akr) Click [Open] Button.
<KM083701>
2007/03
[AKD5366VR-A]
[Function3 Dialog]
sequence register setting executed. Click [F3] Button. control sequence. address, Data Interval time. "-1" address step where sequence should paused. Click [Start] button. Then this sequence executed. sequence paused step Interval="-1". Click [START] button, sequence restarts from paused step. This sequence saved opened [Save] [Open] button Function3 window. extension file name "aks".
Figure Window [F3]
<KM083701>
2007/03
[AKD5366VR-A]
[Function4 Dialog]
sequence that created [Function3] assigned buttons executed. When [F4] button clicked,
window shown Figure opens.
Figure [F4] window
<KM083701>
2007/03
[AKD5366VR-A]
6-1. [OPEN] buttons left side [START] buttons
Click [OPEN] button select sequence file (*.aks). sequence file name displayed shown Figure.
Figure [F4] window Click [START] button, then sequence executed.
6-2. [SAVE] [OPEN] buttons right side
[SAVE]: sequence file names assign saved. file name *.ak4. [OPEN]: sequence file names assign that saved *.ak4 loaded.
6-3. Note
This function doesn't support pause function sequence function. files need same folder used [SAVE] [OPEN] function right side. When sequence changed [Function3], file should loaded again order reflect change.
<KM083701>
2007/03
[AKD5366VR-A]
[Function5 Dialog] register setting that created [SAVE] function main window assigned buttons executed. When [F5] button clicked, following window shown Figure opens.
Figure [F5] window
7-1. [OPEN] buttons left side [WRITE] button
Click [OPEN] button select register setting file (*.akr).
Click [WRITE] button, then register setting executed.
7-2. [SAVE] [OPEN] buttons right side
[SAVE]: register setting file names assign saved. file name *.ak5. [OPEN]: register setting file names assign that saved *.ak5 loaded.
7-3. Note
files need same folder used [SAVE] [OPEN] function right side. When register setting changed [Save] Button main window, file should loaded again order reflect change.
<KM083701>
2007/03
[AKD5366VR-A]
MEASUREMENT RESULTS
[Measurement condition] Measurement unit: Audio Precision, System Cascade MCLK 256fs 64fs BICK 48kHz 24bit Power Supply AVDD TVDD 5.0V, DVDD 3.3V Interface Temperature Room External Condition Input resistor (Ri) 47k, Feedback resistor (Rf) IPGA Gain Parameter Pre-Amp Characteristics: S/(N+D) (A-weighted) Analog Input Characteristics: S/(N+D) (-0.5dB Input) D-Range (-60dB Input) Interchannel Isolation Result (Lch Rch) Unit
102.9 102.8 107.9 107.6 LIN1/RIN1 Pre-Amp IPGA ADC, IPGA=0dB, ALC=OFF fs=48kHz 92.1 92.2 fs=48kHz, A-weighted 102.1 102.1 fs=48kHz, A-weighted 102.2 102.1 114.4 114.9
<KM083701>
2007/03
[AKD5366VR-A]
[ADC Plot: fs=48kHz]
-100 -110 -120 -130 -140 -150 -160 -170 -180
Figure Plot (Input Level -0.5dB)
-100 -110 -120 -130 -140 -150 -160 -170 -180
Figure Plot (Input Level -60dB)
<KM083701>
2007/03
[AKD5366VR-A]
-100 -110 -120 -130 -140 -150 -160 -170 -180
Figure Plot Input, Noise Floor)
-72.5 -77.5 -82.5 -87.5 -92.5 -97.5 -100 -102.5 -105 -107.5 -110 -112.5 -115 -117.5 -120 -140 -130 -120 -110 -100
Figure THD+N Input Level
<KM083701>
2007/03
[AKD5366VR-A]
-72.5 -77.5 -82.5 -87.5 -92.5 -97.5 -100 -102.5 -105 -107.5 -110 -112.5 -115 -117.5 -120
Figure THD+N Input Frequency
-0.05 -0.1 -0.15 -0.2 -0.25 -0.3 -0.35 -0.4 -0.45 -0.5 -0.55 -0.6 -0.65 -0.7 -0.75 -0.8 -0.85 -0.9 -0.95
Figure Frequency Response
<KM083701>
2007/03
[AKD5366VR-A]
-100 -110 -120 -130 -140 -140
-130
-120
-110
-100
Figure Linearity
-100 -105 -110 -115 -120 -125 -130 -135 -140
Figure Crosstalk
<KM083701>
2007/03
[AKD5366VR-A]
Revision History
Date (YY/MM/DD) 06/04/05 07/03/28 Manual Revision KM083700 KM083701 Board Revision Reason First Edition Circuit Change Manual Change Coment
Condenser: Capacitance Value Change: C32, C33: Open Measurement Result Change: Plot Data Added Control Software Manual Change
IMPORTANT NOTICE These products their specifications subject change without notice. Before considering application, consult Asahi Kasei Microsystems Co., Ltd. (AKM) sales office authorized distributor concerning their current status. assumes liability infringement patent, intellectual property, other right application information contained herein. export these products, devices systems containing them, require export license other official approval under regulations country export pertaining customs tariffs, currency exchange, strategic materials. products neither intended authorized critical components safety, life support, other hazard related device system, assumes responsibility relating such use, except with express written consent Representative Director AKM. used here: hazard related device system designed intended life support maintenance safety applications medicine, aerospace, nuclear energy, other fields, which failure function perform reasonably expected result loss life significant injury damage person property. critical component whose failure function perform reasonably expected result, whether directly indirectly, loss safety effectiveness device system containing which must therefore meet very high standards performance reliability. responsibility buyer distributor product distributes, disposes otherwise places product with third party notify that party advance above content conditions, buyer distributor agrees assume responsibility liability hold harmless from claims arising from said product absence such notification.
<KM083701>
2007/03
TEST8
TEST7
TEST6
TEST5
RIN5
RIN4
RIN3
RIN2
RIN1
LIN5
CSN/CAD1
TEST1 CCLK/SCL
LIN4 CDTI/SDA
TEST2 SEL2
LIN3 SEL1
TEST3 SEL0
LIN2
AK5366VR
SMUTE
TEST4 TVDD
0.1u
LIN1
MCLK
LOPIN
LRCK
LOUT ROPIN IPGAR VCOM IPGAL DVDD ROUT SDTO AVDD DVSS AVSS
BICK
4.7u
0.1u
4.7u
0.1u
0.1u
2.2u
Title Size
AKD5366VR-A-48LQFP
Document Number
Date:
AK5366VR
Sheet
Tuesday, December 2006
RIN5
RIN4
RIN3
RIN2
RIN1
CAD0 CAD1 SEL2 SEL1 SEL0
CAD0
MODE1 CAD0 CAD1 SEL2 SEL1 SEL0
LIN5
CCLK
LIN4
CDTI
DGND
AGND
LIN3
SEL2
SEL1
LIN2
SEL0
SMUTE
LIN1
5366VR_PDN
LOUT
5366VR_MCLK
5366VR_SLRCK LRCK LRCK
SLAVE MASTER
AVDD
(short)
TA48M33F
5366VR_SBICK BICK 0.1u TVDD BICK
0.1u
TVDD
TVDD
(open) SDTO
Title Size
ROUT
(short)
Date:
AKD5366VR-A AK5366VR1 Tuesday, December 2006
Document Number Sheet
HSU119
74HC14
74HC14
0.1u
TRANS
DIF2
RESETN DIF1
MCLK
MCLK
DIF0
DIT_DIF PORT1
SDTI
BICK
0.1u
LRCK
DVSS
FS0/CSN
DVDD
LRCK
FS1/CDTI
CKS1
CKS1
BICK
MCLK
SDTO
MCLK BICK LRCK SDTO
PORT2
FS2/CCLK
CKS0
CKS0
FS3/CDTO
AK4103
74HCT541
Title Size
Date:
0.1u
0.1u
CKS1 CKS0
MODE2
DIT_DIF CKS1 CKS0
Document Number
AKD5366VR-A AK4103
Sheet
Tuesday, December 2006
RIN1
LIN1
LOUT
RIN1
LIN1
LOUT
RIN2
RIN2
LIN2
LIN2 ROUT
ROUT
RIN3
RIN3
LIN3
LIN3
RIN4
RIN4
LIN4
LIN4
RIN5
RIN5
LIN5
LIN5
Title Size
Document Number
Date:
AKD5366VR-A Input/Output
Sheet
Tuesday, December 2006
12.288MHz MCLK
74HCU04
74HCU04
74AC74
MCLK
74HC4040
0.1u
CAD1
HSU119
5366VR_SBICK
74HC14
74HC14
SMUTE
5366VR_SLRCK
PORT3
CCLK/SCL CDTI/SDA SDA(ACK)
74HCT157
0.1u
5366VR_MCLK
5366VR_PDN
CTRL
SMUTE
CCLK
U10A
1.8K CDTI 74HC14, 74HCU04, 74HC4040 74AC74, 74HCT157, 74LS07
74LS07 74LVC541
0.1u
0.1u
0.1u
0.1u
0.1u
0.1u
Title Size
Date:
AKD5366VR-A LOGIC Tuesday, December 2006
Document Number Sheet
Other recent searches
VPM-S600 - VPM-S600 VPM-S600 Datasheet
SP1820 - SP1820 SP1820 Datasheet
NJM2734SCC - NJM2734SCC NJM2734SCC Datasheet
HM24-1A83-10-4 - HM24-1A83-10-4 HM24-1A83-10-4 Datasheet
EC110 - EC110 EC110 Datasheet
CDLE-033-643 - CDLE-033-643 CDLE-033-643 Datasheet
2SK0601G - 2SK0601G 2SK0601G Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
