Power Integrated Slim Mouse Sensor ADNB-3532 mouse bundle small f

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Power Integrated Slim Mouse Sensor ADNB-3532 mouse bundle small f

Datasheet Thumbnail

Top Searches for this datasheet

ADNB-3532
Power Integrated Slim Mouse Sensor
ADNB-3532 mouse bundle small form factor (SFF) illuminated navigation system. bundle consists integrated chip-on-board (COB), mouse sensor ADNS-3530 lens ADNS3150-001. ADNS-3530 low-power optical navigation sensor. new, low-power architecture automatic power management modes, making ideal batteryand power-sensitive applications such cordless input devices. ADNS-3530 capable high-speed motion detection addition, on-chip oscillator integrated minimize external components. ADNS-3530, along with ADNS-3150-001 lens, forms complete compact mouse tracking system. There moving parts which means high reliability less maintenance user. addition, precision optical alignment required, facilitating high volume assembly. bundle sensor programmed registers through four-wire serial port. packaged surface mountable package.
Features
power architecture Small form factor Surface mount technology (SMT) device Self-adjusting power-saving modes longest battery life High speed motion detection Self-adjusting frame rate optimum performance Motion detect output Internal oscillator clock input needed Selectable 1000 resolution Wide operating voltage: nominal Four wire serial port Minimal number passive components Integrated chip-on-board
Applications
Optical mice Optical trackballs Integrated input devices Battery-powered input device
Theory Operation
ADNS-3530 based Optical Navigation Technology, which measures changes position optically acquiring sequential surface images (frames) mathematically determining direction magnitude movement. ADNS-3530 contains Image Acquisition System (IAS), Digital Signal Processor (DSP), four wire serial port. acquires microscopic surface images lens illumination system. These images processed determine direction distance motion. calculates relative displacement values. external microcontroller reads information from sensor serial port. microcontroller then translates data into PS2, USB, signals 0before sending them host game console. Bundle Part Number Part Number ADNB-3532 ADNS-3530 ANDS-3150-001 Description Integrated sensor Small form factor lens
Pinout ADNS-3530 Optical Mouse Sensor
Name MISO SCLK MOSI MOTION XY_LED LED_GND SHTDWN AVDD AGND Description Serial Data Output (Master In/Slave Out) Serial Clock Input Serial Data Input (Master Out/Slave Motion Detect (Active Output) Control Ground Current Shutdown (Active High Input) Positive Terminal Negative Terminal Analog Supply Voltage Ground Ground Analog Ground Supply Voltage Ground Chip Select (Active Input)
AVDD AGND
SHTDWN LED-GND XY-LED MOTION MOSI SCLK MISO
Figure Package outline drawing (top view)
12.90 0.20 (0.508 0.008) 1.00 1.60 (0.039) (0.063)
4.80 (0.189) 9.60 0.20 (0.378 0.008) 8.40 (0.331)
0.80 (0.031)
0.50 (0.020)
1.19 (0.047)
PROTECTIVE KAPTON TAPE
NOTES: DIMENSIONS MILLIMETERS (INCHES). COPLANARITY PADS: CUMULATIVE PITCH TOLERANCE: 0.15 PITCH TOLERANCE: MAXIMUM FLASH: DIMENSIONAL TOLERANCE (UNLESS OTHERWISE STATED): 0.15
OPTICAL CENTER
GUIDE HOLE
4.21 (0.166)
5.61 (0.221)
GUIDE HOLE 5.89 (0.232) 10.35 (0.408) 9.50 (0.374) 1.70 (0.067) 0.85 (0.033)
1.95 (0.077)
1.35 (0.053)
Figure Package outline drawing
CAUTION: advised that normal static precautions taken handling assembly this component prevent damage and/or degradation which induced ESD.
Overview Optical Mouse Sensor Assembly
Avago Technologies provides IGES file drawing describing base plate molding features lens alignment. components interlock they mounted onto defined features base plate. ADNS-3530 sensor designed surface mounting PCB, looking down. There aperture stop features package that align lens. ADNS-3150-001 lens provides optics imaging surface well illumination surface optimum angle. Features lens align sensor base plate.
0.53 (0.21)
0.53 (0.21) 1.60 (0.063) 5.89 (0.232)
0.45 (0.18) 0.45 (0.18) 4.20 (0.165) OPTICAL CENTER
8.40 (0.331)
Figure Recommended customer's PADOUT spacing
CUSTOMER
ADNS-3530
ADNS-3150-001
MOUSE BOTTOM COVER
Figure assembly drawing ADNB-3532
ADNS-3530
ADNS-3150-001
CUSTOMERSUPPLIED BASE PLATE
Figure Exploded view
ADNS-3530
ADNS-3150-001
CUSTOMERSUPPLIED BASE PLATE
Figure Exploded bottom view
Assembly Considerations
Surface mount sensor other electrical components into PCB. Reflow entire assembly no-wash solder process. Place lens onto base plate. Care must taken avoid contaminating staining lens. Remove protective kapton tape from optical aperture sensor LED. Care must taken keep contaminants from entering aperture. Recommend place facing during entire mouse assembly process. Recommend hold first vertically kapton removal process. Insert assembly over lens onto base plate aligning post retain assembly. lens piece alignment posts which will mate with alignment holes sensor aperture. optical position reference base plate lens. Note that motion button presses must minimized maintain optical alignment.
Install mouse case. There MUST feature case press down onto sensor ensure sensor lens components interlocked correct vertical height.
Design Considerations Improved Performance
improved electrostatic discharge performance, typical creepage clearance distance shown table below. Assumption: base plate construction Avago Technologies supplied IGES file ADNS3150-001 lens. Typical Distance Creepage Clearance Millimeters 2.76
Note that lens material polycarbonate therefore, cyanoacrylate-based adhesives other adhesives that damage lens should used.
BOTTOM BOTTOM MATING SURFACE LENS 2.28 (0.09)
SENSOR CUSTOMER'S
CUSTOMER'S BASE PLATE
3.25 BOTTOM NAVIGATION SURFACE (0.13)
2.50 NAVIGATION (0.10) SURFACE
0.29 LENS (0.01) BOTTOM LENS NAVIGATION SURFACE
NAVIGATION SURFACE
0.97 (0.04) BOTTOM MATING SURFACE LENS NAVIGATION SURFACE
Figure Sectional view assembly
CUSTOMER'S
SENSOR
CUSTOMER'S BASE PLATE
LENS
SENSOR
NAVIGATION SURFACE
Figure Sectional view assembly highlighting optical mouse components
Figure Schematic diagram interface between ADNS-3530 microcontroller
Note: supply ground paths should laid using star topology.
Regulatory Requirements
Passes worldwide analogous emission limits when assembled into mouse with shielded cable following Avago Technologies recommendations. Passes IEC-1000-4-3 radiated susceptibility level when assembled into mouse with shielded cable following Avago Technologies recommendations. Passes EN61000-4-4/IEC801-4 tests when assembled into mouse with shielded cable following Avago Technologies recommendations. flammability level UL94 V-0.
Absolute Maximum Ratings
Parameter Storage Temperature Lead Solder Temperature Supply Voltage (Sensor Only) Input Voltage Latchup Current Iout -0.5 -0.5 Symbol Minimum Maximum Units pins, human body model Method 3015 pins pins seconds, below seating plane Notes
Recommended Operating Conditions
Parameter Operating Temperature Power Supply Voltage Power Supply Rise Time Supply Noise (Sinusoidal) Distance from Lens Reference Plane Surface Speed Acceleration Symbol -0.1 0.97 Minimum Typical Maximum Units 0.001 +0.1 volts mVp-p in/sec Including noise Active drive, duty cycle Result Notes
Serial Port Clock Frequency fSCLK
CUSTOMER'S
SENSOR
0.97 (0.04)
LENS
NAVIGATION SURFACE
Figure Distance from lens reference plane surface
Electrical Specifications
Parameter Motion Delay After Reset
Electrical Characteristics over recommended operating conditions. Typical values 25°C, VDD3 2.85
Symbol tMOT-RST Min. Typical Max. Units Notes From POWER_UP_RESET register write valid motion, assuming motion present From SHTDWN active current From SHTDWN inactive valid motion. Notes: RESET must asserted after shutdown. Refer section "Notes Shutdown Forced Rest," also note tMOT-RST From RESTEN bits current From RESTEN bits cleared valid motion From SCLK falling edge MISO data valid, load conditions Data held until next falling SCLK edge Amount time data valid after SCLK rising edge From data valid SCLK rising edge From rising SCLK last first data byte, rising SCLK last second data byte From rising SCLK last first data byte, rising SCLK last second address byte From rising SCLK last first data byte, falling SCLK first address byte next command From rising SCLK last address byte, falling SCLK first data being read Minimum inactive time after motion burst before next usage From falling edge first SCLK rising edge From last SCLK rising edge rising edge, valid MISO data transfer From last SCLK rising edge rising edge, valid MOSI data transfer From rising edge MISO high-Z state supply current during ramp from
Shutdown Wake from Shutdown
tSHTDWN tWAKEUP
Forced Rest Enable Wake from Forced Rest MISO Rise Time MISO Fall Time MISO Delay After SCLK MISO Hold Time MOSI Hold Time MOSI Setup Time Time Between Write Commands
tREST-EN tREST-DIS tr-MISO tf-MISO tDLY-MISO thold-MISO thold-MOSI tsetup-MOSI tSWW
1/fSCLK
Time Between Write tSWR Read Commands Time Between Read tSRW Subsequent Commands tSRR
Read Address-Data Delay Inactive After Motion Burst SCLK Active SCLK Inactive (for Read Operation) SCLK Inactive (for Write Operation) MISO High-Z MOTION Rise Time MOTION Fall Time SHTDWN Pulse Width Transient Supply Current
tSRAD
tBEXIT tNCS-SCLK tSCLK-NCS tSCLK-NCS tNCS-MISO tr-MOTION tf-MOTION tP-SHTDWN IDDT
Electrical Specifications
Parameter Supply Current Various Modes Peak Supply Current Shutdown Supply Current Input Voltage Input High Voltage Input Hysteresis Input Leakage Current Output Voltage
Electrical Characteristics over recommended operating conditions. Typical values 25°C, =2.85 Symbol IDD_RUN IDD_REST1 IDD_REST2 IDD_REST3 Min. Typical 0.15 0.04 Max. 0.40 0.15 Units Notes Average current, including current. load MISO, MOTION. Peak current bandwidth, including current. SCLK, MOSI must within VDD. SHTDWN must within VDD. SCLK, MOSI, NCS, SHTDWN SCLK, MOSI, NCS, SHTDWN SCLK, MOSI, NCS, SHTDWN SCLK, MOSI, NCS, SHTDWN Iout MISO, MOTION Iout MISO, MOTION MOSI, NCS, SCLK, SHTDWN
IDDSHTDWN VI_HYS Ileak
Output High Voltage Input Capacitance
ADNS-3530 RESOLUTION RESOLUTION (CPI)
WHITE PAPER MANILA WHITE FORMICA BLACK COPY WHITE PINE
0.77 0.87 0.97 1.07 1.17 1.27 1.37 1.47 1.57 1.67 1.77 1.87 1.97 Z-HEIGHT (mm)
Figure Mean resolution
TYPICAL PATH DEVIATION
LARGEST SINGLE PERPENDICULAR DEVIATION FROM STRAIGHT LINE DEGREES PATH LENGTH INCHES; SPEED ips; RESOLUTION 1000
MAXIMUM DISTANCE (MOUSE COUNT) WHITE PAPER MANILA WHITE FORMICA WHITE PINE BLACK COPY
0.77 0.87 0.97 1.07 1.17 1.27 1.37 1.47 1.57 1.67 1.77 1.87 1.97 DISTANCE FROM LENS REFERENCE PLANE NAVIGATION SURFACE (mm)
Figure Typical path deviation distance (mm) Relationship mouse count distance (mouse count)/n (cpi). E.g.: Deviation mouse count 7/1000 0.007 inch, where 1000.
Power Management Modes
ADNS-3530 three power-saving modes. Each mode different motion detection period, affecting response time mouse motion (Response Time). sensor automatically changes appropriate mode, depending time since last reported motion (Downshift Time). parameters each mode shown following table. Response Time (Nominal) 16.5 Downshift Time (Nominal)
lines that comprise port: SCLK: Clock input. always generated master (the microcontroller). MOSI: Input data. (Master Out/Slave MISO: Output data. (Master In/Slave Out) NCS: Chip select input (active low). needs activate serial port; otherwise, MISO will high MOSI SCLK will ignored. also used reset serial port case error.
Mode Rest Rest Rest
Chip Select Operation
serial port activated after goes low. raised during transaction, entire transaction aborted serial port will reset. This true transactions. After transaction aborted, normal address-to-data transaction-to-transaction delay still required before beginning next transaction. improve communication reliability, serial transactions should framed NCS. other words, port should remain enabled during periods non-use because EFT/B events could interpreted serial communication chip into unknown state. addition, must raised after each burstmode transaction complete terminate burst-mode. port available further until burst-mode terminated.
Motion Timing
motion level-sensitive output that signals microcontroller when motion occurred. motion lowered whenever motion set; other words, whenever there data Delta_X Delta_Y registers. Clearing motion reading Delta_Y Delta_X, writing Motion register) will motion high.
Mode
power savings, will continuously ADNS-3530 will flash only when needed.
Synchronous Serial Port
synchronous serial port used read parameters ADNS-3530, read motion information. port four wire serial port. host microcontroller always initiates communication; ADNS-3530 never initiates data transfers. SCLK, MOSI, driven directly microcontroller. port pins shared with other slave devices. When high, inputs ignored output tristated.
Write Operation
Write operation, defined data going from microcontroller ADNS-3530, always initiated microcontroller consists bytes. first byte contains address (seven bits) indicate data direction. second byte contains data. ADNS-3530 reads MOSI rising edges SCLK.
SCLK MOSI
MISO
MOSI DRIVEN MICRO-CONTROLLER
Figure Write operation
SCLK
MOSI thold, MOSI tsetup, MOSI
Figure MOSI setup hold time
Read Operation
read operation, defined data going from ADNS3530 microcontroller, always initiated microcontroller consists bytes. first byte contains address, sent microcontroller over MOSI, indicate data direction. second byte contains data driven ADNS-3530 over MISO. sensor outputs MISO bits falling edges SCLK samples MOSI bits every rising edge SCLK.
SCLK CYCLE SCLK MOSI
MISO
tSRAD DELAY
Figure Read operation
SCLK tDLY-MISO MISO tHOLD-MISO
Figure MISO delay hold time
NOTE: 0.5/fSCLK minimum high state SCLK also minimum MISO data hold time ADNS-3530. Since falling edge SCLK actually start next read write command, ADNS-3530 will hold state data MISO until falling edge SCLK. Required Timing Between Read Write Commands There minimum timing requirements between read write commands serial port.
tSWW
SCLK ADDRESS DATA ADDRESS DATA
WRITE OPERATION
WRITE OPERATION
Figure Timing between write commands
rising edge SCLK last data second write command occurs before required delay (tSWW), then first write command complete correctly.
tSWR
SCLK ADDRESS DATA ADDRESS
WRITE OPERATION
NEXT READ OPERATION
Figure Timing between write read commands
rising edge SCLK last address read command occurs before required delay (tSWR), write command complete correctly.
tSRW tSRR
tSRAD
SCLK ADDRESS READ OPERATION DATA ADDRESS
NEXT READ WRITE OPERATION
Figure Timing between read either write subsequent read commands
During read operation SCLK should delayed least tSRAD after last address data ensure that ADNS-3530 time prepare requested data. falling edge SCLK first address either read write command must least tSRR tSRW after last SCLK rising edge last data previous read operation.
Burst Mode Operation
Burst mode special serial port operation mode that used reduce serial transaction time motion read. speed improvement achieved continuous data clocking from multiple registers without need specify register address, requiring normal delay period between data bytes. Burst mode activated reading Motion_Burst register. ADNS-3530 will respond with contents Motion, Delta_Y, Delta_X, SQUAL, Shutter_Upper,
Shutter_Lower Maximum_Pixel registers that order. burst transaction terminated after first three bytes sequence read bringing high. After sending register address, microcontroller must wait tSRAD then begin reading data. data bits read with delay between bytes driving SCLK normal rate. data latched into output buffer after last address received. After burst transmission complete, microcontroller must raise line least tBEXIT terminate burst mode. serial port available until reset with NCS, even second burst transmission.
tSRAD
SCLK MOTION_BURST REGISTER ADDRESS READ FIRST BYTE
FIRST READ OPERATION
READ SECOND BYTE
READ THIRD BYTE
Figure Motion burst timing
Notes Power-Up
ADNS-3530 does perform internal power self-reset; POWER_UP_RESET register must written every time power applied. appropriate sequence follows: Apply power Drive high, then reset port Write 0x5a register 0x3a
Read from registers 0x02, 0x03 0x04 read these same three bytes from burst motion register 0x42) time regardless state motion pin. During power-up there will period time after power supply high before clocks available. table below shows state various pins during power-up reset.
State Signal Pins After Valid MISO SCLK MOSI XY_LED MOTION SHTDWN Power-Up Functional Undefined Ignored Ignored Undefined Undefined Must High Before Reset High Undefined Ignored Ignored Undefined Undefined Must Before Reset Functional Functional Functional Undefined Undefined Must After Reset Functional Depends Depends Depends Functional Functional Functional
Notes Shutdown Forced Rest ADNS-3530 Rest mode through Configuration_Bits register (0x11). This allow further power savings applications where sensor does need operate time. ADNS-3530 Shutdown mode asserting SHTDWN pin. proper operation, SHTDWN pulse width must least tSHTDWN. Shorter pulse widths cause chip enter undefined state. addition, port should accessed when SHTDWN asserted. (Other same accessed, long sensor's asserted.) table below shows state various pins during shutdown. After deasserting SHTDWN, full reset must initiated. Wait tWAKEUP before accessing port, then write 0x5A POWER_UP_RESET register. register settings must then reloaded.
MISO SCLK MOSI XY_LED MOTION
SHTDWN active Functional* Undefined Undefined Undefined Current Undefined
*NCS must held (high) shared with other devices. either state sensor only device addition microcontroller. Note: There long wakeup times from shutdown forced Rest. These features should used power management during normal mouse motion.
Registers ADNS-3530 registers accessible serial port. registers used read motion data status well device configuration. Address 0x00 0x01 0x02 0x03 0x04 0x05 0x06 0x07 0x08 0x09 0x0a 0x0b 0x0c 0x0d 0x0e 0x0f 0x10 0x11 0x12-0x2d 0x2e 0x2f-0x38 0x3a 0x3b-0x3d 0x3e 0x3f 0x42 Register Product_ID Revision_ID Motion Delta_Y Delta_X SQUAL Shutter_Upper Shutter_Lower Maximum_Pixel Pixel_Sum Minimum_Pixel Pixel_Grab CRC0 CRC1 CRC2 CRC3 Self_Test Configuration_Bits Reserved Observation Reserved POWER_UP_RESET Reserved Inverse_Revision_ID Inverse_Product_ID Motion_Burst Read/Write 0xFD 0xF2 Default Value 0x0D 0x02 0x00 0x03
Product_ID Access: Read
Address: 0x00 Reset Value: 0x0D Field PID7 PID6 PID5 PID4 PID3 PID2 PID1 PID0
Data Type:
8-bit unsigned integer
USAGE: This register contains unique identification assigned ADNS-3530. value this register does change; used verify that serial communications link functional.
Revision_ID Access: Read
Address: 0x01 Reset Value: 0x02 Field RID7 RID6 RID5 RID4 RID3 RID2 RID1 RID0
Data Type:
8-bit unsigned integer
USAGE: This register contains revision. subject change when versions released.
Motion Access: Read/Write Field Data Type: field
Address: 0x02 Reset Value: 0x00 PIXRDY PIXFIRST Reserved Reserved
Reserved Reserved
USAGE: Register 0x02 allows user determine motion occurred since last time read. set, then user should read registers 0x03 0x04 accumulated motion. Read this register before reading Delta_Y Delta_X registers. Writing anything this register clears bits, Delta_Y Delta_X registers. written data byte saved. Internal buffers accumulate more than eight bits motion either internal buffers overflows, then absolute path data lost set. This cleared once some motion been read from Delta_X Delta_Y registers,
buffers full scale. Since more data present buffers, cycle reading Motion, Delta_X Delta_Y registers should repeated until motion (MOT) cleared. Until cleared, either Delta_X Delta_Y registers will read either positive negative full scale. motion register been read long time, take read cycles clear buffers, 1000 cpi, cycles. clear overflow, write anything this register. PIXRDY will whenever valid pixel data byte available Pixel_Dump register. Check that this before reading from Pixel_Dump. ensure that Pixel_Grab pointer been reset pixel initial write Pixel_Grab, check PIXFIRST high.
Field Name
Description Motion since last report motion Motion occurred, data ready reading Delta_X Delta_Y registers Pixel Dump data byte available Pixel_Dump register data available data available This when Pixel_Grab register written when complete pixel array been read, initiating increment pixel 0,0. Pixel_Grab data from pixel Pixel_Grab data from pixel Motion overflow, and/or buffer overflowed since last report overflow Overflow occurred
PIXRDY
PIXFIRST
Delta_Y Access: Read
Address: 0x03 Reset Value: Undefined
Field
Data Type: Eight complement number USAGE: movement counts since last report. Absolute value determined resolution. Reading clears register.
MOTION -128 -127 +126 +127
DELTA_Y
NOTE: Avago Technologies RECOMMENDS that registers 0x03 0x04 read sequentially.
Delta_X Access: Read
Address: 0x04 Reset Value: Undefined
Field
Data Type: Eight complement number USAGE: movement counts since last report. Absolute value determined resolution. Reading clears register.
MOTION -128 -127 +126 +127
DELTA_X
NOTE: Avago Technologies RECOMMENDS that registers 0x03 0x04 read sequentially.
SQUAL Access: Read Field
Address: 0x05 Reset Value: Undefined
Data Type: Upper bits 9-bit unsigned integer USAGE: SQUAL (Surface Quality) measure number valid features visible sensor current frame. maximum SQUAL register value 167. Since small changes current frame result changes SQUAL, variations SQUAL when looking surface expected.
Shutter_Upper Access: Read Field Shutter_Lower Access: Read Field
Address: 0x06 Reset Value: Undefined
Address: 0x07 Reset Value: Undefined
Data Type: Sixteen unsigned integer USAGE: Units clock cycles. Read Shutter_Upper first, then Shutter_Lower. They should read consecutively. shutter adjusted keep average maximum pixel values within normal operating ranges. shutter value automatically adjusted.
Maximum_Pixel Access: Read Field
Address: 0x08 Reset Value: Undefined
Data Type: Eight-bit number USAGE: Maximum Pixel value current frame. Minimum value maximum value 254. maximum pixel value vary with every frame.
Pixel_Sum Access: Read
Address: 0x09 Reset Value: Undefined Field
Data Type:
High bits unsigned 17-bit integer
USAGE: This register used find average pixel value. reports seven bits 16-bit counter, which sums pixels current frame. described full divided 512. find average pixel value, following formula: Average Pixel Register Value 128/121 Register Value 1.06 maximum register value 240. minimum pixel value change every frame.
Minimum_Pixel Access: Read Field Data Type:
Address: 0x0a Reset Value: Undefined
Eight-bit number
USAGE: Minimum Pixel value current frame. Minimum value maximum value 254. minimum pixel value vary with every frame.
Pixel_Grab Access: Read/Write Field Data Type:
Address: 0x0b Reset Value: Undefined
Eight-bit word
USAGE: test purposes, sensor will read contents pixel array, pixel frame. start pixel grab, write anything this register reset pointer pixel 0,0. Then read PIXRDY Motion register. When PIXRDY set, there valid data this register read out. After data this register read, pointer will automatically increment next pixel. Reading continue indefinitely; once complete frame's worth pixels been read, PIXFIRST will high indicate start first pixel address pointer will start beginning location again.
(Pixel Array Looking Through ADNS-3150-001 Lens)
BOTTOM VIEW MOUSE
VIEW MOUSE
HOLE MOUSE BOTTOM COVER LENS
POSITIVE
POSITIVE
Figure Surface image pixel address
CRC0 Access: Read
Address: 0x0c Reset Value: Undefined Field CRC07 CRC06 CRC05 CRC04 CRC03 CRC02 CRC01 CRC00
Data Type:
Eight-bit number
USAGE: Register 0x0c reports first byte system self test results. Value 0xAF. Self Test register 0x10.
CRC1 Access: Read
Address: 0x0d Reset Value: Undefined Field CRC17 CRC16 CRC15 CRC14 CRC13 CRC12 CRC11 CRC10
Data Type:
Eight number
USAGE: Register 0x0c reports second byte system self test results. Value 0x4E. Self Test register 0x10.
CRC2 Access: Read
Address: 0x0e Reset Value: Undefined Field CRC27 CRC26 CRC25 CRC24 CRC23 CRC22 CRC21 CRC20
Data Type:
Eight-bit number
USAGE: Register 0x0e reports third byte system self test results. Value 0x31. Self Test register 0x10.
CRC3 Access: Read
Address: 0x0f Reset Value: Undefined Field CRC37 CRC36 CRC35 CRC34 CRC33 CRC32 CRC31 CRC30
Data Type:
Eight-bit number
USAGE: Register 0x0f reports fourth byte system self test results. Value 0x22. Self Test register 0x10.
Self_Test Access: Write Field Data Type:
Address: 0x10 Reset Value: TESTEN Reserved Reserved Reserved Reserved Reserved Reserved Reserved
field
USAGE: TESTEN register 0x10 start system self-test. test takes During this time, write read through port. Results available CRC0-3 registers. After self-test, reset chip start normal operation. Field Name TESTEN Description Enable System Self Test Disabled Enable
Configuration_bits Access: Read/Write Field Data Type: field
Address: 0x11 Reset Value: 0x03 Reserved RESTEN
RESTEN
Reserved Reserved Reserved Reserved
USAGE: Register 0x11 allows user change configuration sensor. Setting RESTEN forces sensor into Rest mode, described power modes section above. allows selection between 1000 resolution. Note: Forced Rest long wakeup time should used power management during normal mouse motion. Field Name RESTEN1-0 Description Puts chip into Rest mode normal operation force Rest1 force Rest2 force Rest3 Sets resolution 1000
Reserved
Address: 0x12-0x2d
Observation Access: Read/Write Field Data Type: field
Address: 0x2e Reset Value: Undefined MODE0 OBS3 OBS2 OBS1 OBS0 MODE1 Reserved Reserved
USAGE: Register 0x2e provides bits that every frame. used during EFTB testing check that chip running correctly. Writing anything this register will clear bits. Field Name MODE1-0 Description Mode Status: Reports which mode sensor Rest1 Rest2 Rest3 every frame
OBS3-0
Reserved
Address: 0x2f-0x39
POWER_UP_RESET Access: Write Field Data Type:
Address: 0x3a Reset Value: Undefined RST6 RST5 RST4 RST3 RST2 RST1 RST0 RST7
8-bit integer
USAGE: Write 0x5A this register reset chip. settings will revert default values.
Inverse_Revision_ID Access: Read Field Data Type:
Address: 0x3e Reset Value: 0xFD NRID6 NRID5 NRID4 NRID3 NRID2 NRID1 NRID0
NRID7
Inverse 8-bit unsigned integer
USAGE: This value inverse Revision_ID. used test port.
Inverse_Revision_ID Access: Read Field Data Type:
Address: 0x3f Reset Value: 0xF2 NPID6 NPID5 NPID4 NPID3 NPID2 NPID1 NPID0
NPID7
Inverse 8-bit unsigned integer
USAGE: This value inverse Product_ID. used test port.
Motion_Burst Access: Read Field Data Type: Various
Address: 0x42 Reset Value:
USAGE: Read from this register activate burst mode. sensor will return data Motion register, Delta_Y, Delta_X, Squal, Shutter_Upper, Shutter_Lower, Maximum_Pixel. minimum bytes should read during burst read. Reading first bytes clears motion data.
ADNS-3150-001
Small Form Factor Lens
ADNS-3150-001 small form factor (SFF) lens designed with Avago Technologies ADNS-3530 integrated sensor. Together with LED, ADNS3150-001 lens provide direct illumination optical imaging necessary proper operation sensor. ADNS-3150-001 lens precision molded optical component should handled with care avoid scratching optical surfaces.
12.90 (0.508) 1.66 (0.065) 1.70 (0.067)
1.50 (0.059) 0.50 (0.020)
4.35 (0.171) 1.90 (0.075)
9.00 (0.354)
(0.220)
5.60
3.00 (0.118)
GATE (MAX. PROTRUDE) EITHER SIDE
3.37 (0.133)
0.89 0.15 (0.035 0.006) 9.50 (0.374) 4.46 (0.176)
5.80 (0.228)
1.28 (0.050)
0.62 (0.024)
0.13 (0.005)
ILLUMINATION LENS SURFACE 0.62 (0.024) ILLUMINATION LENS SURFACE
IMAGING LENS SURFACE IMAGING LENS SURFACE
1.96 (0.077) 0.59 0.15 (0.23 0.006) 0.88 0.15 (0.35 0.006) 0.20 (0.008)
ILLUMINATION LENS SURFACE
SECTION
0.29 (0.011)
NOTES: DIMENSIONS MILLIMETERS (INCHES). DIMENSIONAL TOLERANCE: ±0.1 UNLESS OTHERWISE SPECIFIED. ANGULAR TOLERANCE: ±3°. MAXIMUM FLASH: +0.2
Figure ADNS-3150-001 lens outline drawings details
Lens Design Optical Performance Specifications
Symbol Numerical Aperture Magnification Design Wavelength Depth Field Coverage Radius Min.
specifications based Mechanical Assembly Requirements. Typical 0.1642 ±0.1 0.85 Image circle radius Image nominal location Max. Units Conditions
*Lens material polycarbonate. Cyanoacrylate based adhesives should used they will cause lens material deformation.
Mounting Instructions ADNS-3150-001 Lens Base Plate
IGES format drawing file with design specifications mouse base plate features available. These features useful maintaining proper positioning alignment ADNS-3150-001 when used with Avago Technologies Optical Sensor. This file obtained contacting your local Avago Technologies sales representative.
product information complete list distributors, please website:
www.avagotech.com
Avago, Avago Technologies, logo trademarks Avago Technologies Limited United States other countries. Data subject change. Copyright 2007 Avago Technologies Limited. rights reserved. AV02-0249EN 2007

Power Integrated Slim Mouse Sensor ADNB-3532 mouse bundle small f

Top Searches for this datasheet

Other recent searches