ACT1100 ACT1700 Standard Clock Oscillators ACT1100 full size thro

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

ACT1100 ACT1700 Standard Clock Oscillators ACT1100 full size thro

Datasheet Thumbnail

Top Searches for this datasheet

ACT1100 ACT1700 Standard Clock Oscillators
ACT1100 full size through hole oscillator. ACT1700 half size through hole oscillator. popularity these families still remains even after advent smaller surface mount devices. With wide frequency operating temperature ranges, these series offer cost good reliability ATM, Networking, Microprocessor Consumer applications. option with supply voltage 2.5V available please contact sales desk details. frequencies 500KHz, >125MHz 10ppm stability please refer ACT1100HS/1700HS data.
Specification
Parameter
Frequency Range Frequency Stability Temp Operating Range Temp Storage Range Supply Voltage Supply Current Duty Cycle Output Level Output Level Output Logic Output Load Symbol f/fo Topr Tstg TW/t
Specification
500KHz 125.0MHz ±25ppm, ±50ppm ±100ppm +70°, +70°C -40~85°C 3.3Vdc ±10% 5.0Vdc ±10% 15mA 25mA 25mA 35mA 40/60%, 45/55% 40/60%, 45/55% HCMOS 0.4V max, HCMOS .33V 0.4V max, HCMOS 0.5V 2.4V min, HCMOS 2.97V 2.4V min, HCMOS 4.5V HCMOS Gates CMOS 10nSec max, 3nSec typical Measured between 0.4V 2.4V 15pF) CMOS 10nSec max, 3nSec typical Measured between 10%~ 15pF) 4mSec max, State Connection ±5ppm year
Condition
Please Specify Please Specify Please Specify Please Specify 27MHz 125MHz Measured +1.4Volts Measured 3.3V 5.0V 3.3V 5.0V
Rise Fall Time
tr/tf
Start-up Time Option Aging
Please Specify @25°C
Plating Material leads SnAgCu Soldering conditions please refer page
ACT1100 SERIES ACT1700 'CL' SERIES
Please note that parameters necessarily specified same device
Customer specify Frequency, Operating Temperature Range, Frequency Stability, Supply Voltage, Duty Cycle, Output Enable (Tristate) required
line with ongoing policy product evolvement improvement, above specification subject change without notice
ISO9001:2000 Registered quotations further information please contact Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY,
http://www.actcrystals.com
Issue Date 23/3/6
ACT1100 ACT1700 Standard Clock Oscillators
Reliability tests
Test Test Method Measurement Requirements
Leak
Helium bomb: Pressure 200kpa Time pressure release measure within 30min 750mm height. drops. Onto wood. Peak acceleration 981m/s2 Pulse duration Each axis. shocks each axis 55Hz return 10Hzamplitude 1.5mm sweep time 1min. each axis. Total test time profile fig.1 below and/or soldering iron applied temperature 350±10°C
<4x10-9pa.m3/s
Drop
Shock
Vibration
Resistance Soldering Heat
Aging
85±3°C days measurements after least atmospheric conditions. Specification page must met.
High Temperature 105±3°C measurements after least atmospheric conditions Storage
Temperature -55±3°C 2hrs measurements after least atmospheric conditions Storage 100cycles temperature profile below. Measurements after least atmospheric conditions
Thermal Cycling
Damp Heat Constant
Temperature 40±2°C 90~95% days. Measurements after atmospheric conditions
Solderability
255±5°C 10±0.5s using Rosin resin methyl alcohol flux Solvent (1:4) dipped nominal depth 0.5mm.
line with ongoing policy product evolvement improvement, above specification subject change without notice
ISO9001:2000 Registered quotations further information please contact Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY,
http://www.actcrystals.com
Issue Date 23/3/6
ACT1100 ACT1700 Standard Clock Oscillators
Application circuits
line with ongoing policy product evolvement improvement, above specification subject change without notice
ISO9001:2000 Registered quotations further information please contact Business Centre, Molly Millars Lane, Wokingham, Berkshire, RG41 2EY,
http://www.actcrystals.com
Issue Date 23/3/6

ACT1100 ACT1700 Standard Clock Oscillators ACT1100 full size thro

Top Searches for this datasheet

Other recent searches