SPDT Absorptive Switch High Isolation Insertion Loss 1.1dB 4GHz O

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SPDT Absorptive Switch High Isolation Insertion Loss 1.1dB 4GHz O

Datasheet Thumbnail

Top Searches for this datasheet

HRF-SW1001
SPDT Absorptive Switch
High Isolation Insertion Loss 1.1dB 4GHz Operating Frequency Integrated CMOS Control Logic Integrated Protection Digital Single Positive Supply Voltage Ultra Small LPCC Packaging Impedance matched systems
Product Description
Honeywell HRF-SW1001 high performance single pole double throw (SPDT) absorptive switch that ideal wireless basestation handset applications that require minimum power minimum insertion loss. HRF-SW1001 manufactured with Honeywell's patented Silicon Insulator (SOI) CMOS technology, which provides performance GaAs with economy integration capabilities conventional CMOS technology.
HRF-SW1001 LPCCPackage
Electrical Specifications 25oC
Results Vdd=5.0 10%, unless otherwise stated, Z0=75 ohms Parameter Test Condition Frequency Minimum
Insertion Loss Input Power Vss=Gnd Vss= Two-Tone Inputs Vss=Gnd Vss= Cntl 90%/10%Rf In-Band
Typical
53.5 42.5 39.0 1.1:1 1.2:1 1.2:1
Maximum
Units
Ratio Ratio Ratio
Isolation
VSWR*
1.3:1
Compression
Input
Trise, Tfall* Ton, Toff Transients design
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295
HRF-SW1001
Electrical Specifications 25oC
Parameter Single Supply Voltage CMOS Logic Level CMOS Logic Level Input Leakage Current Performance curves +5.0 Minimum 3.3* Typical Maximum Units
Absolute Maximum Ratings1
Parameter Digital Logic Digital Logic Maximum Input Power Voltage Operating Temperature Range Storage Temperature Range Absolute Maximum +6.0 +125 Units Degrees Degrees
(Note Operation beyond these parameters cause permanent damage. Latch-Up: Unlike conventional CMOS switches, Honeywell's HRF-SW1001 immune latch-up. Protection: Although this device contains protection circuitry digital inputs, conventional precautions should taken ensure that Absolute Maximum Ratings exceeded.
Package Outline Drawing
Bottom View, LPCCPackage ASAT LPCC Marketing Outline Dwg. GMJ00004 more information http://www.asat.com
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295
HRF-SW1001
Truth Table
Switch Control
CMOS Low, CMOS High
Output INPUT
Output INPUT
Configuration
Function
GROUND GROUND SWITCH CONTROL
Function
GROUND GROUND GROUND GROUND
Evaluation Circuit Board Connections
HRFEvaluation
Honeywell HRF-SW1000
Ground Open Control
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295
HRF-SW1001
Performance Curves
Insertion Loss
Insertion Loss versus Frequency
Insertion Loss (dB)
Insertion Loss curve shows worst case loss versus frequency +5.0 +/10%, 25C, Ohms
Frequency
Isolation
Isolation versus Frequency
-20.00 -30.00 -40.00 -50.00
Isolation curve shows typical isolation "off" state output insertion path.
(dB)
-60.00 -70.00 -80.00 -90.00 -100.00
Frequency (GHz)
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295
HRF-SW1001
Return Loss
Input Output Return Losses versus Frequency
0.00 -5.00
Return Loss (dB)
-10.00 -15.00 -20.00 -25.00 -30.00 -35.00 -40.00 -45.00 -50.00
return loss curve shows input return loss S11, output return loss insertion path S22, output return loss isolation state S33.
Frequency (GHz)
Evaluation Circuit Board
Honeywell's evaluation board provides easy method evaluating performance switch. Simply connect power, signals measuring switch performance less than minutes.
HRF-SW1001 Evaluation Board
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295
HRF-SW1001
Evaluation Circuit Board Layout Design Details
Item Switch Chip Capacitor Connector Description Impedance Matched Multi-Layer HRF-SW1001 Switch Panasonic Model ECU-E1C103KBQ Capacitor, .01uf 0402 Johnson Connectors Model 142-0701-801 Coaxial Connector Mil-Max Model 800-10-064-10-001 Header Pins
Ordering Information
Ordering Number
HRF-SW1001-B HRF-SW1001-TR HRF-SW1001-E
(Note Contact Honeywell details
Product
Delivered Chip Tubes Delivered Tape Reel Engineering Evaluation Board
LPCC
registered Trademark ASAT Ltd.
Honeywell reserves right make changes improve reliability, function design. Honeywell does assume liability arising application product circuit described herein; neither does convey license under patent rights rights others.
Site: Email: 2002 1001W www.mysoiservices.com mysoiservices@honeywell.com Published June 2002 Page Honeywell Solid State Electronics Center 12001 State Highway Plymouth, Minnesota 55441-4799 1-800-323-8295

SPDT Absorptive Switch High Isolation Insertion Loss 1.1dB 4GHz O

Top Searches for this datasheet

Other recent searches