Designed with approved amplifiers intrinsically safe barriers explosiv

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Designed with approved amplifiers intrinsically safe barriers explosiv

Datasheet Thumbnail

Top Searches for this datasheet

SMI30 Series Intrinsically Safe Sensors
Designed with approved amplifiers intrinsically safe barriers explosive environments Very high excess gain; range (standard models) Fast response models (200 range) available special order Totally sealed, self-contained, intrinsically safe threaded-barrel opposed mode sensor pairs rugged housings Highly immune noise: best noise immunity selfcontained emitter/receiver pair Internal alignment indicator viewed either from side from front receiver through lens Integral mini-type 3-pin "QD" (quick-disconnect) connector
Rugged, NEMA 6P-plus sensors threaded barrel housings
SMI30 Series sensors, shown with Intrinsic Safety (see page
KEMA 03ATEX1441
Banner SMI30 Series intrinsically safe barrel sensors extremely rugged powerful opposed mode infrared sensor pairs designed most demanding industrial applications. Their high excess gain (460 foot range) provides enough sensing power penetrate heaviest contamination (excess gain curve, page Electronics fully epoxy-encapsulated maximum resistance mechanical shock vibration. Positive sealing both ends, with exposed epoxy interfaces, eliminates leak paths (including capillary leakage). Construction exceeds NEMA (IEC standards. Sensors approximately 1.2" diameter long. SMI30 series receivers operate from These sensors carry entity approval from Factory Mutual Research intrinsically safe operation hazardous atmospheres. SMI30 Series sensors certified being intrinsically safe when used with approved intrinsic safety barriers. SMI30 Series sensors suitable intrinsically safe hazardous locations defined Article National Electrical Code (see classifications, above right). SMI30 Series sensors also certified Factory Mutual non-incendive devices when used Division locations (except Groups without intrinsic safety barriers. SMI30 Series sensors wired either two- three-wire current-sinking operation. three-wire hookup, which requires intrinsic-safety barriers dual barrier), sink current 15mA. two-wire hookup, which requires barrier, sinks 10mA (OFF state) 20mA state). Intrinsic safety barriers available from Banner (see page Current trip point amplifier CI3RC2 also offered (page Several mounting brackets available (see page
(continued page
Specifications
SUPPLY VOLTAGE: Emitters: 25mA. Receivers: 15mA max. Division use, with barriers, requires minimum system supply voltage 10V. hookup information, pages 3-4. OUTPUT: Receivers only: Current sinking open-collector transistor. Three-wire hookup sinks 15mA maximum continuous, 10-30V Two-wire hookup sinks 10mA (OFF state) 20mA state), 10-30V Outputs short-circuit protected. SENSING BEAM: nanometers, infrared; effective beam size 0.75" diameter. RESPONSE TIME: milliseconds on/off (models with response available special order) REPEATABILITY: chart, page Response Time Repeatability specifications independent signal strength. INDICATOR: Internal lights whenever receiver sees modulated light source. Emitters have "power indicator LED. indicators visible through lens from side sensor. CONSTRUCTION: NEMA IP67. 30mm diameter tubular threaded housing, positive sealing both ends; quad-ring sealed acrylic lens. Electronics fully epoxy encapsulated. nuts provided. CABLE: Three-wire mini-type cable long model SMICC-312 long model SMICC-330). Cable electrical properties: 40pf/ft.; .20µH/ft. Order cable separately from sensor. MOUNTING ALTERNATIVES: 30mm clearance hole; SMB30C split clamp mounting bracket (page SMB30MM two-axis mounting bracket (page SMB30S swivel mounting bracket (page OPERATING TEMPERATURE RANGE: +70°C (-40 +18°F).
35331 rev.
Banner SMI30 Series Intrinsically Safe Sensors designed meet following standards:
1604 22.2 #142-M1987 22.2 #157-92 22.2 #213-M1987 3610 FM3611
WARNING These photoelectric presence sensors include self-checking redundant circuitry necessary allow their personnel safety applications. sensor failure malfunction result either energized de-energized sensor output condition.
Never these products sensing devices personnel protection. Their safety devices create unsafe condition which could lead serious injury death. Only MACHINE-GUARD PERIMETER-GUARD Systems, other systems designated, designed meet OSHA ANSI machine safety standards point-of-operation guarding devices. other Banner sensors controls designed meet these standards, they must used sensing devices personnel protection.
Printed
11/06
SMI30 Series Intrinsically Safe Sensors
SMI30 Series receivers have alignment indicator that lights whenever receiver "sees" modulated light source. Emitters have indicate "power on". indicators mounted internally preserve waterproof integrity sensor housing, visible from both side front sensor through sensor's quad-ring sealed acrylic lens. innovative circuitry used SMI30 Series emitters receivers provides best noise immunity self-contained opposed mode sensor pair. applications where optical crosstalk between sensors might problem, SMI30 Series emitters receivers available with choice three modulation frequencies (frequency "A", frequency "B", frequency "C"). This makes possible highpowered sensor pairs different frequencies close proximity each other without crosstalk. (NOTE: frequency standard; frequencies available special order. emitter receiver must same modulation frequency.) chart page summary models. Each unit supplied with hexagonal nuts. 30mm clearance hole required mounting, mounting bracket models SMB30MM, SMB30S, SMB30C available (page models have built-in standard quick-disconnect ("QD") connector. "QD" models mate with 12-foot long model SMICC-312 30-foot long model SMICC-330 mini-type cable (sold separately from sensor).
SMI30 Series Dimensions
PVC-covered mini-type cable
MBCC Series Cable
(order separately)
SMICC-312 feet, 36356) SMICC-330 feet, 36357) 3-wire cable emitters receivers
Sensor (male connector)
Cable (female connector)
Hookup Information
SMI30 Series sensors certified intrinsically safe ONLY when used with certified energy-limiting intrinsically safe barriers. Emitter units two-wire hookup (there output connection). Note from hookup diagram (page that receiver installation made using either single barrier (2-wire hookup) with dual channel barrier (3-wire hookup). 2-wire configuration, sensor acts current sink, drawing less than 10mA state more than 20mA state. customer must provide current sensing device ("current sensor" diagram) convert current logic level. SMI30 Series sensors used with Banner Current Amplifier Control Module CI3RC2. CI3RC2 module purchased (with model RS-11 module socket, dual-channel barrier, rail barrier mounts included) specifying model CI2BK-2. dualchannel intrinsic barrier (alone) ordered specifing model CI2B-1. photo, page 3-wire configuration, output used directly control loads less than 15mA. selecting barrier, important consider barrier's resistance. sensors must have least volts across brown blue power leads proper operation, barrier will cause voltage drop resistance. formula that determines much resistance allowed
Cable connector (female, SMICC cable, side view)
Note that, 3-wire hookup, barrier series with load. This results apparent saturation voltage output that higher than sensor output amount (current times voltage) drop through barrier. Emitters 2-wire hookup; receivers either 3-wire hookup. chart (page summary models. Barriers generally classified either "positive input" "negative input". SMI30 Series intrinsically safe sensors require "positive input" barriers both supply load. blue (negative supply) lead sensor normally connected ground terminal barrier. user this equipment responsible proper installation maintenance equipment, must conform with certification requirements relating barriers maximum allowable capacitance inductance field wiring. doubt about these requirements, applications engineers refer appropriate authority.
(supply voltage volts).
supply voltage then maximum resistance ohms. supply voltage then maximum resistance ohms. This includes resistance current sensing device used 2-wire configuration), barrier resistance must further reduced current sensor resistance.
SMI30 Series Intrinsically Safe Sensors
Hookup Diagrams
SAFE AREA
BARRIERS REQUIRED DIV. MAX. (Reference NOTE CSA)
HAZARDOUS AREA
3-WIRE HOOKUP
BARRIER
CSA:
I.S.
BLACK
Entity parameters: Vmax Imax
MAX.
SMI30 Series Sensor
BOTTOM VIEW (colors shown arefor mating cable MBCC-312) INSTALLATION NOTES: Barriers must installed accordance with manufacturer's instructions.
OPERATING VOLTAGE: INPUT (CONNECTION CONTROL ROOM 18-30 EQUIPMENT SHOULD GENERATE MORE THAN 250V)
BROWN
EARTH GROUND (less than ohm)
BUSBAR
BLUE
Barrier entity parameters must meet following requirements: Ccable Vmax Lcable Maximum non-hazardous area voltage must exceed 250V. guidance installation, ANSI/ISA RP12.6, "Installation Intrinsically Safe Instrument Systems Hazardous (Classified) Locations". sensors suitable installation without barriers Class Div. Groups Class Div. Group Class Div. when installed through wall suitable enclosure with provision connection rigid metal conduit National Electrical Code, acceptable local inspection authority having jurisdiction.
NOTE: Emitters have output connection connection black wire)
SAFE AREA
BARRIERS REQUIRED DIV. MAX. (Reference NOTE CSA)
HAZARDOUS AREA
BLACK CSA:
2-WIRE HOOKUP
I.S.
Entity parameters: Vmax Imax
(OFF STATE) STATE)
BARRIER
SMI30 Series Sensor
KEMA Vmax Imax
OPERATING VOLTAGE: INPUT 18-30
CURRENT SENSOR
(CONNECTION CONTROL ROOM EQUIPMENT SHOULD GENERATE MORE THAN 250V)
BROWN
BOTTOM VIEW (colors shown mating cable MBCC-312) INSTALLATION NOTES:
EARTH GROUND (less than ohm)
BUSBAR
BLUE
Barriers must installed accordance with manufacturer's instructions. Barrier entity parameters must meet following requirements: Ccable Vmax Lcable Maximum non-hazardous area voltage must exceed 250V. Install accordance with Canadian Electrical Code, Part sensors suitable installation without barriers Class Div. Groups when installed through wall suitable enclosure with provision connection rigid metal conduit Canadian Electrical Code, acceptable local inspection authority having jurisdiction.
Sensor Models Emitter 10ms Models Receiver Opr. Receiver Opr. Emitter Models Receiver Opr. Receiver Opr.
Frequency SMI306EQ SMI30AN6RQ SMI30RN6RQ SMI306EYQ SMI30AN6RYQ SMI30RN6RYQ
Frequency SMI306EBQ SMI30AN6RBQ SMI30RN6RBQ
Frequency SMI306ECQ SMI30AN6RCQ SMI30RN6RCQ SMI306EYCQ SMI30AN6RYCQ SMI30RN6RYCQ
Div. installations (without barriers), observe following warnings: WARNING: EXPLOSION HAZARD DISCONNECT EQUIPMENT UNLESS POWER BEEN SWITCHED AREA KNOWN NON-HAZARDOUS. AVERTISSEMENT: RISQUE D'EXPLOSION AVANT DECONNECTER L'EQUIPMENT, COUPER COURANT S'ASSURER L'EMPLACEMENTS DESIGNE DANGEREUX. barriers with Volt/Ohm parameters used, following parameters shall apply: Single-Channel Barrier Systems (max), (min) Single-Channel Barrier Dual-Channel Systems (max), (min) (max), (min) (max), (min) (max), (min) diode return
Banner Engineering Corp. 9714 Tenth Avenue North Minneapolis, 55441 MANUFACTURING DRAWING #35392 rev.
CHANGES MADE THIS DRAWING WITHOUT PRIOR APPROVAL FACTORY MUTUAL
HOOKUP DIAGRAM: SMI30 SERIES INTRINSICALLY-SAFE SENSORS
CI3RC2 Current Amplifier Module
Hookup Banner MAXI-AMP CI3RC2 Current Amplifier Module
SAFE AREA
(see data sheet packed with CI3RC2 more information)
HAZARDOUS AREA
Hookup using single-channel barriers
BROWN BLUE
SMI30 Series Emitter
I.S.
INPUT: (OFF STATE) STATE) AUX. INPUT COMMON OPTO-COUPLER OUTPUT: 20mA max.
BARRIER
BLACK
RELAY OUTPUT CONTACTS
BROWN
SMI30 Series Receiver
I.S. BARRIERG
BLUE
130V SUPPLY
CI3RC2
250V
SAFE AREA
BUSBAR
EARTH GROUND (less than
BOTTOM VIEW SENSOR (colors shown mating cable model MBCC-312)
HAZARDOUS AREA
Dual Barrier I.S.
BROWN
Series Emitter
BLUE
Hookup using dual-channel barrier
RELAY OUTPUT CONTACTS
INPUT: (OFF STATE) STATE) AUX. INPUT COMMON OPTO-COUPLER OUTPUT: 20mA max.
BLUE
BLACK
BROWN
BUSBAR
Series Receiver
130V SUPPLY
CI3RC2
EARTH GROUND (less than
250V
BOTTOM VIEW CABLE CONNECTOR SENSOR (colors shown mating cable model MBCC-312)
MAXI-AMPCI3RC2 Module
Banner MAXI-AMP module model CI3RC2 (part number 36606) self-contained module which converts current output signal SMI30 Series sensor trip point switch. Both sensors opposed mode pair wired model CI3RC2 using two-wire hookup, which requires single channel dual channel intrinsic safety barrier(s). this mode, SMI30 receiver sinks milliamps "OFF" state milliamps "ON" state. CI3RC2 senses this current change switches internal relays which easily wired most loads and/ additional control circuitry. Model CI3RC2 powered either 105-130 210-250V CI3RC2 supplies power operate both emitter receiver. Inputs protected against short circuits. Built-in circuit diagnostics indicate overload either input pulsing status light. CI3RC2 module isolated output switches. There rated SPDT electromechanical relay, solid-state transistor switch which used logic-level interfaces.
Functional Schematic, CI3RC2
SPECIFICATIONS, CI3RC2
SUPPLY VOLTAGE: 250V 50/60 (8VA). OUTPUT CONFIGURATION: SPDT electromechanical relay: Contact rating: 250V max., max., amps max. (resistive load), 1/10 240V Install transient suppressor (MOV) across contacts that switch inductive loads. Closure time: milliseconds max. Release time: 10milliseconds max. Maximum switching speed: operations/second. Mechanical life: 20,000,000 operations Solid-state relay: SPST optically-coupled transistor; max., 20mA max. INPUTS: Trip point output "OFF": milliamps Trip point output "ON": milliamps Trip point range input overload indication: 30mA 80mA. INDICATOR LEDs: Status indicator OUTPUT "ON" INPUT overload/short. OPERATING TEMPERATURE: 50°C 122°F). CONSTRUCTION: rugged NORYL® polyphenylene oxide (PPOTM) housing, 1.6" 2.3" Standard round-pin 11-pole base. RS-11 socket equivalent.
SMI30 Series Intrinsically Safe Sensors
Models: part numbers, frequencies, response times
SMI30 Series Intrinsically Safe Sensors Part Numbers
Sensor Models Frequency (standard)
Repeatability:
Frequency (special order)
Repeatability:
Frequency (special order)
Excess Gain Curve
Repeatability:
100,000
Models with response time
Emitters Receivers (light operate) Receivers (dark operate)
SMI306EQ (35268) SMI30AN6RQ (35271) SMI30RN6RQ (35274)
Repeatability:
SMI306EBQ (35269) SMI30AN6RBQ (35272) SMI30RN6RBQ (35275)
SMI306ECQ (35270) SMI30AN6RCQ (35273) SMI30RN6RCQ (35276)
Repeatability:
10,000
SMI30 series opposed mode intrinsically safe sensors
1,000 10ms response models DISTANCE 1000
response models
Models with response time
Emitters Receivers (light operate) Receivers (dark operate)
SMI306EYQ (35277) SMI30AN6RYQ (35279) SMI30RN6RYQ (35281)
SMI306EYCQ (35278) SMI30AN6RYCQ (35280) SMI30RN6RYCQ (35282)
Accessories: apertures, barriers, kits, mounting brackets
APG30S Aperture SM30 Series Sensors (27533)
These water-tight apertures SM30 Series sensors used size shape effective beam limit excess gain avoiding "burn-through" effects. Apertures sold kit, which includes thread-on stainless steel housing, flat glass lens, quad-ring seals, round slotted aperture disks. stainless steel aperture housing functions equally well with VALOX® stainless steel sensor models. glass lens useful protecting SM30's acrylic lens against substances that hostile acrylics, such concentrated acids alkalis industrial solvents. Aperture sizes include following. Round: .06", .12", .70" diameter Slotted: .04", .10", .20" wide
Intrinsic Safety Kits with Intrinsic Safe Sensors
CI2BK-1 (36860) includes CI3RC2 current amplifier, RS11 socket, DIN-rail mount, single-channel intrinsically safe barrier. CI2BK-2 (36605) includes CI3RC2 current amplifier, RS11 socket, DIN-rail mount, dual-channel intrinsically safe barrier.
Barriers available separately: Single channel barrier (model CIB-1, 27030) Dual channel barrier (model CI2B-1, 36865)
Mounting Brackets
Accessory mounting bracket model SMB30MM (27162) curved mounting slots versatility mounting orientation. sensor mounts bracket using nuts provided. Bracket material 11-gauge zincplated steel. Curved mounting slots have clearance 1/4" screws.
SMB30MM Mounting Bracket (27162)
SMB30S Swivel Bracket
(33204)
model SMB30S swivel-mount bracket (33204, right) offers ultimate mounting versatility SMI30s other sensors with threads. SMI30 threads into adjustable captive ball bracket, which then held firmly place when locking bolts tightened. Bracket material black PBT. Stainless steel mounting hardware included. Split Clamp Bracket model SMB30C (32636, right) similar SMB30S, without adjustable captive swivel ball. grips M30x1,5 threaded sensor threaded barrel (S30 EZBEAM sensor shown). Bracket material black PBT. Stainless steel mounting hardware included.
Special Conditions Safe
SMB30C Split Clamp
(32636)
Parts enclosure non-conducting generate ignition-capable level ESD. Cleaning equipment shall done only with damp cloth.
WARRANTY: Banner Engineering Corporation warrants products free from defects year. Banner Engineering Corporation will repair replace, free charge, product manufacture found defective time returned factory during warranty period. This warranty does cover damage liability improper Banner products. This warranty lieu other warranty either expressed implied.
Banner Engineering Corp.
9714 Tenth Ave. Minneapolis, 55441
Telephone: (763)544-3164
(applications): (763)544-3573

Designed with approved amplifiers intrinsically safe barriers explosiv

Top Searches for this datasheet

Other recent searches