Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511

Datasheet Thumbnail

Top Searches for this datasheet

19-4760; 8/02
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
MAX4511/MAX4512/MAX4513 quad, singlepole/single-throw (SPST), fault-protected analog switches. They pin-compatible with industry-standard nonprotected DG201/DG202/DG213. These switches feature fault-protected inputs Rail-to-Rail® signal handling capability. normally open (NO_) normally closed (NC_) terminals protected from overvoltage faults during power-up power-down. During fault condition, terminal becomes open circuit only nanoamperes leakage current flow from source, switch output (COM_) furnishes 10mA appropriate polarity supply voltage load. This ensures unambiguous rail-to-rail outputs when fault begins ends. On-resistance matched between switches max. off-leakage current only 0.5nA +25°C 10nA +85°C. MAX4511 four normally closed switches. MAX4512 four normally open switches. MAX4513 normally closed normally open switches. These CMOS switches operate with dual power supplies ranging from ±4.5V ±18V single supply between +36V. digital inputs have +0.8V +2.4V logic thresholds, ensuring both TTL- CMOS-logic compatibility when using ±15V single +12V supply.
Features
±40V Fault Protection with Power ±36V Fault Protection with ±15V Supplies Switches with Power Rail-to-Rail Signal Handling Output Clamped Appropriate Supply Voltage During Fault Condition; Transition Glitch Signal Paths with ±15V Supplies Power-Supply Sequencing Required ±4.5V ±18V Dual Supplies +36V Single Supply Power Consumption, <2mW Four Separately Controlled SPST Switches Pin-Compatible with Industry-Standard DG411/DG412/DG413, DG201/DG202/DG213 TTL- CMOS-Compatible Logic Inputs with Single +15V ±15V Supplies
MAX4511/MAX4512/MAX4513
Configurations/ Functional Diagrams/Truth Tables
VIEW
Applications
Equipment Data Acquisition Industrial ProcessControl Systems Avionics Redundant/Backup Systems
COM1 VGND COM4
COM2 N.C. COM3
Ordering Information
PART MAX4511CPE MAX4511CSE MAX4511CUE MAX4511C/D MAX4511EPE MAX4511ESE MAX4511EUE MAX4511MJE TEMP RANGE +70°C +70°C +70°C +70°C -40°C +85°C -40°C +85°C -40°C +85°C -55°C +125°C PIN-PACKAGE Plastic Narrow TSSOP Dice* Plastic Narrow TSSOP CERDIP
MAX4511
DIP/SO/TSSOP
MAX4511 LOGIC SWITCH
Ordering Information continued data sheet. *Contact factory dice specifications. Rail-to-Rail registered trademark Nippon Motorola, Ltd.
N.C. CONNECTED SWITCHES SHOWN LOGIC INPUT. SWITCHES WITH POWER REMOVED.
Continued data sheet.
Maxim Integrated Products
free samples latest literature: http://www.maxim-ic.com, phone 1-800-998-8800. small orders, phone 408-737-7600 ext. 3468.
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
ABSOLUTE MAXIMUM RATINGS
(Voltages Referenced GND) .-0.3V +44.0V .-44.0V +0.3V V-.-0.3V +44.0V COM_, (Note .(V- 0.3V) 0.3V) NC_, (Note 2).(V+ 36V) 36V) NC_, COM_ .-36V +36V Continuous Current into Terminal.±30mA Peak Current into Terminal (pulsed 1ms, duty cycle).±50mA Continuous Power Dissipation +70°C) (Note Plastic (derate 10.53mW/°C above +70°C) .842mW Narrow (derate 8.70mW/°C above +70°C) .696mW TSSOP (derate 9.4mW/°C above +70°C) .754.7mW CERDIP (derate 10.00mW/°C above +70°C) .800mW Operating Temperature Ranges MAX451_C_ .0°C +70°C MAX451_E_ .-40°C +85°C MAX451_MJE .-55°C +125°C Storage Temperature Range .-65°C +150°C Lead Temperature (soldering, 10s) .+300°C
Note COM_ pins fault protected. Signals COM_ exceeding clamped internal diodes. Limit forward diode current maximum current rating. Note pins fault protected. Signals exceeding -36V +36V damage device. These limits apply with power applied ±40V with
Stresses beyond those listed under "Absolute Maximum Ratings" cause permanent damage device. These stress ratings only, functional operation device these other conditions beyond those indicated operational sections specifications implied. Exposure absolute maximum rating conditions extended periods affect device reliability.
ELECTRICAL CHARACTERISTICS-Dual Supplies
+15V, -15V, TMIN TMAX, unless otherwise noted. Typical values +25°C.)
PARAMETER ANALOG SWITCH Fault-Protected Analog Signal Range Fault-Free Analog Signal Range Non-Protected Analog Signal Range (COM_ Output) COM_ -NO_ COM_ -NC_ On-Resistance COM_ -NO_ COM_ -NC_ On-Resistance Match Between Channels (Note Leakage Current (Note COM_ Leakage Current (Note COM_ Leakage Current (Note VNO_, VNC_ VNO_, VNC_ VCOM_ Applies with power (Note Applies with power (Note Applies with power (Note VCOM_ ±10V, ICOM_ +25°C +25°C VCOM_ ±10V, ICOM_ INO_(OFF), INC_(OFF) VCOM_ ±14V; VNO_, VCOM VCOM_ ±14V; VNO_, VCOM +25°C +25°C +25°C ICOM_(ON) VCOM_ ±14V -0.5 -200 -0.5 -200 -0.5 -400 0.01 0.01 0.01 SYMBOL CONDITIONS (Note UNITS
ICOM_(OFF)
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
ELECTRICAL CHARACTERISTICS-Dual Supplies (continued)
+15V, -15V, TMIN TMAX, unless otherwise noted. Typical values +25°C.)
PARAMETER SYMBOL CONDITIONS (Note UNITS
MAX4511/MAX4512/MAX4513
FAULT +15V, -15V, unless otherwise noted.) COM_ Output Leakage Current, Supplies Input Leakage Current, Supplies Input Leakage Current, Supplies COM_ Output Current, Supplies COM_ Output Resistance, Supplies LOGIC INPUT LOGIC INPUT Input Logic Threshold High Input Logic Threshold Input Current Logic High VIN_H VIN_L IINH_, IINL VIN_ 0.8V 2.4V +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C 0.03 +25°C ICOM_ VNO_ VNC_ ±33V INO_, INC_ VNO_ VNC_ ±25V, VCOM_ VNO_ VNC_ ±40V, VNO_ VNC_ VNO_ VNC_ -33V VNO_ VNC_ ±33V +25°C +25°C +25°C +25°C -200 -200 -200
INO_, INC_
ICOM_ RCOM_
SWITCH DYNAMIC CHARACTERISTICS SWITCH DYNAMIC CHARACTurn-On Time VCOM_ ±10V, Figure VCOM_ ±10V, Figure VCOM_ ±10V, Figure 1.0nF, VNO_ Figure 1MHz, Figure 1MHz, Figure 1MHz, Figure 15pF, 1VRMS, 1MHz, Figure 15pF, 1VRMS, 1MHz, Figure
Turn-Off Time Break-Before-Make Time Delay (MAX4513 Only) Charge Injection (Note Off-Capacitance COM_ Off-Capacitance COM_ On-Capacitance Isolation (Note Channel-to-Channel Crosstalk (Note
tOFF
tBBM CN_(OFF) CCOM_(OFF) CCOM_(ON) VCISO
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
ELECTRICAL CHARACTERISTICS-Dual Supplies (continued)
+15V, -15V, TMIN TMAX, unless otherwise noted. Typical values +25°C.)
PARAMETER POWER SUPPLY Power-Supply Range Supply Current Supply Current IAll VIN_ VIN_ VIN_ Supply Current IGND VIN_ VIN_ C,E, +25°C +25°C +25°C +25°C 0.01 ±4.5 SYMBOL CONDITIONS (Note UNITS
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
ELECTRICAL CHARACTERISTICS-Single +12V Supply
+10.8V +13.2V, TMIN TMAX, unless otherwise noted. Typical values +25°C.) PARAMETER ANALOG SWITCH Fault-Protected Analog Signal Range Fault-Free Analog Signal Range Non-Protected Analog Signal Range (COM_ Output) COM_ -NO_ COM_ -NC_ On-Resistance COM_ -NO_ COM_ -NC_ On-Resistance Match Between Channels (Note Leakage Current (Notes COM_ Leakage Current (Notes COM_ Leakage Current (Notes FAULT COM_ Output Leakage Current, Supply Input Leakage Current, Supply Input Leakage Current, Supply COM_ Output Current, Supply COM_ Output Resistance, Supply ICOM_ VNO_ VNC_ ±30V, VNO_ VNC_ ±25V, VCOM_ VNO_ VNC_ ±40V, VNO_ VNC_ 25V, VNO_ VNC_ +25°C +25°C +25°C +25°C +25°C -200 -200 -200 VNO_, VNC_ VNO_, VNC_ VCOM_ Applies with power (Note Applies with power (Note Applies with power (Note 12V, VCOM_ 10V, ICOM_ 12V, VCOM_ 10V, ICOM_ 12V; VCOM_ 10V; VNO_, 12V; VCOM VNO_, VNC_ 12V, VCOM_ +25°C +25°C +25°C +25°C +25°C -0.5 -200 -0.5 -200 -0.5 -400 0.01 0.01 0.01 -0.3 SYMBOL CONDITIONS (Note UNITS
ION_(OFF), INC_(OFF)
ICOM_(OFF)
ICOM_(ON)
INO_, INC_
INO_, INC_
ICOM_ RCOM_
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
ELECTRICAL CHARACTERISTICS-Single +12V Supply (continued)
+10.8V +13.2V, TMIN TMAX, unless otherwise noted. Typical values +25°C.) PARAMETER LOGIC INPUT Input Logic Threshold High Input Logic Threshold Input Current Logic High VIN_H VIN_L IIN_H, IIN_L VIN_ 0.8V 2.4V +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C +25°C 0.03 1000 1500 1200 SYMBOL CONDITIONS (Note UNITS
SWITCH DYNAMIC CHARACTERISTICS Turn-On Time Turn-Off Time Break-Before-Make Time Delay (MAX4513 Only) Charge Injection (Note Capacitance COM_ Capacitance COM_ Capacitance Isolation (Note Channel-to-Channel Crosstalk (Note POWER SUPPLY Power-Supply Range Supply Current VIN_ VIN_ Supply Current IGND VIN_ Note Note Note Note Note Note Note Note Note C,E, +25°C +25°C +25°C tOFF tBBM (OFF) CCOM_ (OFF) CCOM_ (ON) VISO VCOM_ 10V, Figure VCOM_ 10V, Figure VCOM_ 10V, Figure 1.0nF, VNO_ Figure 1MHz, Figure VCOM_ GND, 1MHz, Figure VCOM_ VNO_ GND, 1MHz, Figure 15pF, 1VRMS, 1MHz, Figure 15pF, 1VRMS, 1MHz, Figure
COM_ pins fault protected. Signals COM_ exceeding clamped internal diodes. Limit forward diode current maximum current rating. pins fault protected. Signals exceeding -36V +36V damage device. These limits apply with power applied ±40V with algebraic convention used this data sheet; most negative value shown minimum column. RON(MAX) RON(MIN). Leakage parameters 100% tested maximum rated temperature guaranteed correlation +25°C. Guaranteed design. isolation log10 VCOM_ (VNC_ VNO_) VCOM_ output, VNC_ VNO_ input switch. Between switches. Leakage testing single-supply operation guaranteed testing with dual supplies.
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
_Typical Operating Characteristics
+25°C, unless otherwise noted.)
SWITCH ON-RESISTANCE VCOM (DUAL SUPPLIES)
MAX4511-01
MAX4511/MAX4512/MAX4513
SWITCH ON-RESISTANCE VCOM TEMPERATURE (DUAL SUPPLIES)
MAX4511-02
SWITCH ON-RESISTANCE VCOM (SINGLE SUPPLY)
SWITCH ON-RESISITANCE
MA4511-03
SWITCH ON-RESISTANCE VCOM +15V -15V +20V -20V +10V -10V +12V -12V
SWITCH ON-RESISTANCE +15V -15V -55°C -40°C +25°C +125°C +85°C
1000
+12V
+15V +20V +24V +30V
VCOM VCOM
SWITCH ON-RESISTANCE VCOM TEMPERATURE (SINGLE SUPPLY)
MAX4511-04
ID(ON), IS(OFF), ID(OFF) LEAKAGES TEMPERATURE
MAX4511-05
CHARGE INJECTION VCOM (DUAL SUPPLIES)
(pC) VCOM SINGLE +12V SUPPLY DUAL ±15V SUPPLIES +15V -15V
MAX4511-06
SWITCH ON-RESISTANCE +125°C +85°C
100n ICOM(OFF) @VNO -14V, VCOM +14V ICOM(OFF) @VNO +14V, VCOM -14V ICOM(ON) @VNO VCOM -14V
LEAKAGE +25°C -40°C
+12V
100p
ICOM(ON) @VNO VCOM +14V INO(OFF) @VNO -14V, VCOM +14V INO(OFF) @VNO +14V, VCOM -14V
-55°C
VCOM TEMPERATURE (°C)
TIMES SUPPLY VOLTAGE
tON, tOFF (ns) SUPPLY VOLTAGE (±V) tOFF (DUAL SUPPLIES) tOFF (SINGLE SUPPLY) (DUAL SUPPLIES) (SINGLE SUPPLY)
MAX4511-07
TIMES TEMPERATURE
MAX4511-08
POWER-SUPPLY CURRENT TEMPERATURE
MAX4511-09
1000
tOFF
SUPPLY CURRENT (µA)
tON, tOFF (ns)
IGND
TEMPERATURE (°C)
TEMPERATURE (°C)
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
Typical Operating Characteristics (continued)
+25°C, unless otherwise noted.)
LOGIC-LEVEL THRESHOLD
MAX4511-10
FREQUENCY RESPONSE
LOSS (dB) -100 -110 -120 PHASE LOSS LOSS
MAX186-14A
-100 -120 PHASE (DEGREES)
LOGIC-LEVEL THRESHOLD
0.01
1000
FREQUENCY (MHz)
Description
NAME IN1-IN4 COM1- COM4 FUNCTION Logic Control Digital Inputs Analog Switch Common* Terminals
Detailed Description
Overview Traditional Fault-Protected Switches
MAX4511/MAX4512/MAX4513 fault-protected CMOS analog switches with unusual operation construction. Traditional fault-protected switches constructed three series FETs. This produces good characteristics, fairly high on-resistance when signals within about each supply rail. voltage side switch approaches within about either supply rail fault condition), switch impedance becomes higher, limiting output signal range protected side switch) approximately less than appropriate polarity supply voltage. During fault condition, output current that flows from protected side switch into load comes from fault source other side switch. switch open load extremely high impedance, input current will very low. switch load impedance, enough current will flow from source maintain load voltage less than supply.
NO1-NO4 Analog Switch Fault-Protected Normally NC1-NC4 Open* Normally Closed* Terminals VGND N.C. Negative Analog Supply Voltage Input. Connect single-supply operation. Ground. Connect digital ground. (Analog signals have ground reference.) Connection-not internally connected Positive Analog Digital Supply-Voltage Input. Internally connected substrate.
long voltage does exceed NC_) COM_ pins identical interchangeable. Either considered input output; signals pass equally well either direction.
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
NORMALLY OPEN SWITCH CONSTRUCTION
HIGH FAULT (NC_) FAULT COM_
V-ESD DIODE SWITCH
Figure Block Diagram
Overview MAX4511/MAX4512/MAX4513
MAX4511/MAX4512/MAX4513 differ considerably from traditional fault-protection switches, with several advantages. First, they constructed with parallel FETs, allowing very on-resistance when switch Second, they allow signals pins that within slightly beyond supply rails passed through switch terminal, allowing rail-to-rail signal operation. Third, when signal exceeds supply rails about 50mV fault condition), voltage COM_ limited appropriate polarity supply voltage. Operation identical both fault polarities. faultprotection extends ±36V from GND. During fault condition, input becomes high impedance regardless switch state load resistance. switch COM_ output current furnished from "booster" FETs connected each supply pin. These FETs typically source sink 10mA.
When power removed, fault protection still effect. this case, terminals virtual open circuit. fault ±40V. COM_ pins fault protected; they normal CMOS switch pins. voltage source connected COM_ pin, should limited supply voltages. Exceeding supply voltage will cause high currents flow through protection diodes, possibly damaging device (see Absolute Maximum Ratings).
Compatibility
These switches have identical pinouts common nonfault-protected CMOS switches. Care should exercised considering them direct replacements existing printed circuit boards, however, since only pins each switch fault protected.
Internal Construction
Internal construction shown Figure with analog signal paths shown bold. single normally open
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
(NO) switch shown; normally closed (NC) configuration identical except logic-level translator becomes inverter. analog switch formed parallel combination N-channel Pchannel which driven simultaneously according input fault condition logic-level state.
COM_ Pins
FETs source about ±10mA from COM_ fault condition. Ensure that COM_ connected low-resistance load, absolute maximum current rating 30mA never exceeded, both normal fault conditions. GND, COM_, pins have fault protection. Reverse ESD-protection diodes internally connected between GND, COM_, both signal GND, COM_, exceeds more than 300mV, these diodes will conduct heavily. During normal operation these reverse-biased diodes leak nanoamps current
Normal Operation
comparators continuously compare voltage NC_) with When signal between switch acts normally, with FETs turning response signals. parallel combination forms low-value resistor between NC_) COM_ that signals pass equally well either direction.
Fault-Protection Voltage Power
maximum fault voltage pins ±36V with power applied ±40V with power off.
Positive Fault Condition
When signal NC_) exceeds about 50mV, high-fault comparator output high, turning FETs This makes NC_) high impedance regardless switch state. switch state "off", FETs turned both NC_) COM_ high impedance. switch state "on", turned sourcing current from COM_.
Failure Modes
MAX4511/MAX4512/MAX4513 lightning arrestors surge protectors. Exceeding fault-protection voltage limits NC_, even very short periods, cause device fail. failure modes obvious, failure switch affect other switches same package.
Negative Fault Condition
When signal NC_) exceeds about 50mV, low-fault comparator output high, turning FETs This makes NC_) high impedance regardless switch state. switch state "off," FETs turned both NC_) COM_ high impedance. switch state "on," turned sinking current from COM_
Ground
There connection between analog signal paths GND. analog signal paths consist N-channel P-channel MOSFET with their sources drains paralleled their gates driven phase logic-level translators. power internal logic logic-level translators input logic thresholds. logiclevel translators convert logic levels switched signals drive gates analog switches. This drive signal only connection between power supplies analog signals. GND, IN_, COM_ have ESD-protection diodes
Transient Fault Response Recovery
When fast rise-time fall-time transient exceeds output (COM_) follows input (IN_) supply rail with only nanoseconds delay. This delay switch on-resistance circuit capacitance ground. When input transient returns within supply rails, however, there longer output recovery time delay. positive faults, recovery time typically 3.5µs. negative faults, recovery time typically 1.3µs. These values depend COM_ output resistance capacitance, production tested guaranteed. delays dependent fault amplitude. Higher COM_ output resistance capacitance increase recovery times.
Logic-Level Thresholds
logic-level thresholds CMOS compatible when +15V. raised threshold increases slightly, when reaches level threshold about 2.8V-above output high level minimum 2.4V, still compatible with CMOS outputs (see Typical Operating Characteristics). Increasing effect logic-level thresholds, does increase gate-drive voltage signal FETs, reducing their on-resistance.
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
Bipolar Supplies
MAX4511/MAX4512/MAX4513 operate with bipolar supplies between ±4.5V ±18V. supplies need symmetrical, their difference exceed absolute maximum rating 44V. 20MHz, on-response several minor peaks that highly layout dependent. problem with high-frequency operation turning switch turning off. off-state switch acts like capacitor passes higher frequencies with less attenuation. 10MHz, isolation about -42dB systems, becoming worse (approximately 20dB decade) frequency increases. Higher circuit impedances also make isolation worse. Adjacent channel attenuation about above that bare socket entirely capacitive coupling.
MAX4511/MAX4512/MAX4513
Single Supply
MAX4511/MAX4512/MAX4513 operate from single supply between +36V when connected GND.
High-Frequency Performance
systems, signal response reasonably flat 50MHz (see Typical Operating Characteristics). Above
Test Circuits/Timing Diagrams
+10V VIN_
VIN_
MAX4511 MAX4512 MAX4513 COM_
10pF
+10V VOUT VOUT
tOFF
CONNECTED (0V) SINGLE-SUPPLY OPERATION.
Figure Switch Turn-On/Turn-Off Times
VIN_ +10V VIN_
VNO_, VNC_ COM_ COM_ VOUT V10pF VOUT tOPEN
MAX4513
CONNECTED (0V) SINGLE-SUPPLY OPERATION.
Figure MAX4513 Break-Before-Make Interval
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
Test Circuits/Timing Diagrams (continued)
VIN_ VIN_
MAX4511 MAX4512 MAX4513
COM_ VVOUT 1000pF
VOUT
VOUT
VOUT MEASURED VOLTAGE CHARGETRANSFER ERROR WHEN CHANNEL TURNS OFF. VOUT
CONNECTED (0V) SINGLE-SUPPLY OPERATION.
Figure Charge Injection
ADDRESS SELECT
MAX4511 MAX4512 MAX4513
COM_ V1MHz CAPACITANCE ANALYZER
CONNECTED (0V) SINGLE-SUPPLY OPERATION.
Figure COM_, NO_, Capacitance
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
Test Circuits/Timing Diagrams (continued)
10nF NETWORK ANALYZER COM_ ISOLATION LOSS VOUT NO_, VMEAS. REF. CROSSTALK VOUT VOUT VOUT
MAX4511/MAX4512/MAX4513
MAX4511 MAX4512 MAX4513
ADDRESS SELECT
10nF
MEASUREMENTS STANDARDIZED AGAINST SHORT SOCKET TERMINALS. ISOLATION MEASURED BETWEEN COM_ "OFF" TERMINALS. LOSS MEASURED BETWEEN COM_ "ON" TERMINALS. CROSSTALK MEASURED BETWEEN COM_ TERMINALS WITH SWITCHES SIGNAL DIRECTION THROUGH SWITCH REVERSED; WORST VALUES RECORDED. CONNECTED (0V) SINGLE-SUPPLY OPERATION.
Figure Frequency Response, Isolation, Crosstalk
Configurations/Functional Diagrams/Truth Tables (continued)
VIEW COM1 VGND COM4 COM2 COM1 VGND COM4 COM2
MAX4512
N.C. COM3
MAX4513
N.C. COM3
DIP/SO
MAX4512 LOGIC SWITCH LOGIC
DIP/SO
MAX4513 SWITCHES SWITCHES
N.C. CONNECTED SWITCHES SHOWN LOGIC INPUT. SWITCHES WITH POWER REMOVED.
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
Chip Topographies
MAX4511
COM1 COM2
Ordering Information (continued)
PART MAX4512CPE MAX4512CSE MAX4512CUE MAX4512C/D MAX4512EPE MAX4512ESE MAX4512EUE MAX4512MJE MAX4513CPE MAX4513CSE MAX4513CUE MAX4513C/D MAX4513EPE MAX4513ESE MAX4513EUE MAX4513MJE TEMP RANGE +70°C +70°C +70°C +70°C -40°C +85°C -40°C +85°C -40°C +85°C -55°C +125°C +70°C +70°C +70°C +70°C -40°C +85°C -40°C +85°C -40°C +85°C -55°C +125°C PIN-PACKAGE Plastic Narrow TSSOP Dice* Plastic Narrow TSSOP CERDIP Plastic Narrow TSSOP Dice* Plastic Narrow TSSOP CERDIP
VGND 0.138" (3.51mm)
COM4 COM3 0.086" (2.261mm)
Contact factory dice specifications.
MAX4512
COM1 COM2 COM1
MAX4513
COM2
VGND 0.138" (3.51mm) VGND
0.138" (3.51mm)
COM4 COM3 0.086" (2.261mm)
COM4 COM3 0.086" (2.261mm)
TRANSISTOR COUNT: SUBSTRATE CONNECTED
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
Package Information
(The package drawing(s) this data sheet reflect most current specifications. latest package outline information, www.maxim-ic.com/packages.)
SOICN .EPS
MAX4511/MAX4512/MAX4513
INCHES 0.069 0.053 0.010 0.004 0.014 0.019 0.007 0.010 0.050 0.150 0.157 0.228 0.244 0.016 0.050
MILLIMETERS 1.35 1.75 0.10 0.25 0.35 0.49 0.19 0.25 1.27 3.80 4.00 5.80 6.20 0.40 1.27
VARIATIONS:
INCHES
MILLIMETERS 4.80 8.55 9.80 5.00 8.75 10.00 MS012
VIEW
0.189 0.337 0.386
0.197 0.344 0.394
FRONT VIEW
SIDE VIEW
PROPRIETARY INFORMATION TITLE:
PACKAGE OUTLINE, .150" SOIC
APPROVAL DOCUMENT CONTROL REV.
21-0041
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511/MAX4512/MAX4513
Package Information (continued)
(The package drawing(s) this data sheet reflect most current specifications. latest package outline information, www.maxim-ic.com/packages.)
PDIPN.EPS CDIPS.EPS
Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches
Package Information (continued)
(The package drawing(s) this data sheet reflect most current specifications. latest package outline information, www.maxim-ic.com/packages.)
TSSOP4.40mm.EPS
MAX4511/MAX4512/MAX4513
Maxim cannot assume responsibility circuitry other than circuitry entirely embodied Maxim product. circuit patent licenses implied. Maxim reserves right change circuitry specifications without notice time.
Maxim Integrated Products, Gabriel Drive, Sunnyvale, 94086 408-737-7600_17 2002 Maxim Integrated Products Printed registered trademark Maxim Integrated Products.

Quad, Rail-to-Rail, Fault-Protected, SPST Analog Switches MAX4511

Top Searches for this datasheet

Other recent searches