Quad 2-Input Exclusive Gate MC54/74HC86A identical pinout LS86; t
|
|
|
Top Searches for this datasheet
Quad 2-Input Exclusive Gate
MC54/74HC86A identical pinout LS86; this device similar function MM74C86 L86, different pinout. device inputs compatible with standard CMOS outputs; with pullup resistors, they compatible with LSTTL outputs. Output Drive Capability: LSTTL Loads Outputs Directly Interface CMOS, NMOS, Operating Voltage Range: Input Current: High Noise Immunity Characteristic CMOS Devices Compliance with Requirements Defined JEDEC Standard Chip Complexity: FETs Equivalent Gates
MC54/74HC86A
SUFFIX CERAMIC PACKAGE CASE 632-08
SUFFIX PLASTIC PACKAGE CASE 646-06
SUFFIX SOIC PACKAGE CASE 751A-03
SUFFIX TSSOP PACKAGE CASE 948G-01
LOGIC DIAGRAM
ORDERING INFORMATION MC54HCXXAJ MC74HCXXAN MC74HCXXAD MC74HCXXADT Ceramic Plastic SOIC TSSOP
ASSIGNMENT
FUNCTION TABLE
Inputs Output
3/97
Motorola, Inc. 1997
MC54/74HC86A
MAXIMUM RATINGS*
Symbol Parameter Value Unit Supply Voltage (Referenced GND) Input Voltage (Referenced GND) Vout Output Voltage (Referenced GND) Input Current, Iout Output Current, Supply Current, Pins Power Dissipation Still Air, Plastic Ceramic SOIC Package TSSOP Package Storage Temperature Tstg
This device contains protection circuitry guard against damage high static voltages electric fields. However, precautions must taken avoid applications voltage higher than maximum rated voltages this high-impedance circuit. proper operation, Vout should constrained range (Vin Vout) VCC. Unused inputs must always tied appropriate logic voltage level (e.g., either VCC). Unused outputs must left open.
Lead Temperature, from Case Seconds (Plastic DIP, SOIC TSSOP Package) (Ceramic DIP)
Maximum Ratings those values beyond which damage device occur. Functional operation should restricted Recommended Operating Conditions. Derating Plastic DIP: mW/_C from 125_C Ceramic DIP: mW/_C from 100_ 125_C SOIC Package: mW/_C from 125_C TSSOP Package: mW/_C from 125_C high frequency heavy load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
RECOMMENDED OPERATING CONDITIONS
Symbol Parameter
Unit
Supply Voltage (Referenced GND)
Vin, Vout
Input Voltage, Output Voltage (Referenced GND) Operating Temperature, Package Types Input Rise Fall Time (Figure
1000
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit
Symbol
Parameter
Test Conditions
25_C 3.15 1.35
85_C 125_C
3.15 1.35 3.15 1.35
Unit
Minimum High-Level Input Voltage
Vout |Iout|
Maximum Low-Level Input Voltage
Vout |Iout|
Minimum High-Level Output Voltage
|Iout|
|Iout| |Iout| |Iout|
2.48 3.98 5.48
2.34 3.84 5.34
2.20 3.70 5.20
High-Speed CMOS Logic Data DL129
MC54/74HC86A
ELECTRICAL CHARACTERISTICS (Voltages Referenced GND)
Guaranteed Limit Symbol Parameter Test Conditions 25_C
85_C 125_C
0.33 0.33 0.33 0.40 0.40 0.40
Unit
Maximum Low-Level Output Voltage
|Iout|
|Iout| |Iout| |Iout| Iout
0.26 0.26 0.26
Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package)
NOTE: Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D).
ELECTRICAL CHARACTERISTICS Input
Guaranteed Limit Symbol tPLH, tPHL Parameter 25_C
85_C 125_C
Unit
Maximum Propagation Delay, Input Output (Figures
tTLH, tTHL
Maximum Output Transition Time, Output (Figures
Maximum Input Capacitance
NOTES: propagation delays with loads other than Chapter Motorola High-Speed CMOS Data Book (DL129/D). Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D). Typical 25°C, Power Dissipation Capacitance (Per Gate)*
Used determine no-load dynamic power consumption: load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
High-Speed CMOS Logic Data DL129
MC54/74HC86A
tPHL OUTPUT tTLH tTHL Includes probe capacitance TEST POINT OUTPUT tPLH DEVICE UNDER TEST
INPUT
Figure Switching Waveforms
Figure Test Circuit
EXPANDED LOGIC DIAGRAM (1/4 Device)
High-Speed CMOS Logic Data DL129
MC54/74HC86A
OUTLINE DIMENSIONS
SUFFIX CERAMIC PACKAGE CASE 632-08 ISSUE
-A14
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEAD WHEN FORMED PARALLEL. DIMESNION NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. INCHES 0.750 0.785 0.245 0.280 0.155 0.200 0.015 0.020 0.055 0.065 0.100 0.008 0.015 0.125 0.170 0.300 0.020 0.040 MILLIMETERS 19.05 19.94 6.23 7.11 3.94 5.08 0.39 0.50 1.40 1.65 2.54 0.21 0.38 3.18 4.31 7.62 0.51 1.01
-TSEATING PLANE
0.25 (0.010)
0.25 (0.010)
SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE
NOTES: LEADS WITHIN 0.13 (0.005) RADIUS TRUE POSITION SEATING PLANE MAXIMUM MATERIAL CONDITION. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 0.052 0.095 0.008 0.015 0.115 0.135 0.300 0.015 0.039 MILLIMETERS 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 1.32 2.41 0.20 0.38 2.92 3.43 7.62 0.39 1.01
SEATING PLANE
SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE
0.25 (0.010)
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSIONS INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.127 (0.005) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION.
SEATING PLANE
0.25 (0.010)
MILLIMETERS 8.75 8.55 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 0.25 0.19 0.25 0.10 5.80 6.20 0.25 0.50
INCHES 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 0.008 0.009 0.004 0.009 0.228 0.244 0.010 0.019
High-Speed CMOS Logic Data DL129
MC54/74HC86A
OUTLINE DIMENSIONS
SUFFIX PLASTIC TSSOP PACKAGE CASE 948G-01 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION DOES INCLUDE MOLD FLASH, PROTRUSIONS GATE BURRS. MOLD FLASH GATE BURRS SHALL EXCEED 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE INTERLEAD FLASH PROTRUSION. INTERLEAD FLASH PROTRUSION SHALL EXCEED 0.25 (0.010) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.08 (0.003) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. TERMINAL NUMBERS SHOWN REFERENCE ONLY. DIMENSION DETERMINED DATUM PLANE -W-. MILLIMETERS 4.90 5.10 4.30 4.50 1.20 0.05 0.15 0.50 0.75 0.65 0.50 0.60 0.09 0.20 0.09 0.16 0.19 0.30 0.19 0.25 6.40 INCHES 0.193 0.200 0.169 0.177 0.047 0.002 0.006 0.020 0.030 0.026 0.020 0.024 0.004 0.008 0.004 0.006 0.007 0.012 0.007 0.010 0.252
0.10 (0.004) 0.15 (0.006)
0.25 (0.010)
IDENT.
DETAIL
0.15 (0.006)
SECTION
0.10 (0.004) SEATING
PLANE
DETAIL
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters which provided Motorola data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer. Mfax trademark Motorola, Inc. reach EUROPE Locations Listed: Motorola Literature Distribution; P.O. 5405, Denver, Colorado 80217. 303-675-2140 1-800-441-2447 JAPAN: Nippon Motorola Ltd.; Tatsumi-SPD-JLDC, Seibu-Butsuryu-Center, 3-14-2 Tatsumi Koto-Ku, Tokyo 135, Japan. 81-3-3521-8315
MfaxTM: RMFAX0@email.sps.mot.com TOUCHTONE 602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Ping Industrial Park, Canada ONLY 1-800-774-1848 Ting Road, N.T., Hong Kong. 852-26629298 INTERNET: http://www.mot.com/SPS/
MC74HC86A/D High-Speed CMOS Logic Data DL129
Other recent searches
MDDM-00066N - MDDM-00066N MDDM-00066N Datasheet
MAC15A6FP - MAC15A6FP MAC15A6FP Datasheet
LRDC-10-2-75J+ - LRDC-10-2-75J+ LRDC-10-2-75J+ Datasheet
HER501 - HER501 HER501 Datasheet
HER508 - HER508 HER508 Datasheet
FSBB20CH60L - FSBB20CH60L FSBB20CH60L Datasheet
74VHC244 - 74VHC244 74VHC244 Datasheet
1N4728A - 1N4728A 1N4728A Datasheet
1N4752A - 1N4752A 1N4752A Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
