Quad 2-Input Gate MC54/74HC08A identical pinout LS08. device inpu
|
|
|
Top Searches for this datasheet
Quad 2-Input Gate
MC54/74HC08A identical pinout LS08. device inputs compatible with Standard CMOS outputs; with pullup resistors, they compatible with LSTTL outputs.
MC54/74HC08A
SUFFIX CERAMIC PACKAGE CASE 632-08
Output Drive Capability: LSTTL Loads Outputs Directly Interface CMOS, NMOS Operating Voltage Range: Input Current: High Noise Immunity Characteristic CMOS Devices Compliance With JEDEC Standard Requirements Chip Complexity: FETs Equivalent Gates
SUFFIX PLASTIC PACKAGE CASE 646-06
SUFFIX SOIC PACKAGE CASE 751A-03
LOGIC DIAGRAM
SUFFIX TSSOP PACKAGE CASE 948B-03
ORDERING INFORMATION MC54HCXXAJ MC74HCXXAN MC74HCXXAD MC74HCXXADT Ceramic Plastic SOIC TSSOP
FUNCTION TABLE
Inputs Output
Pinout: 14-Lead Packages (Top View)
2/98
Motorola, Inc. 1998
MC54/74HC08A
MAXIMUM RATINGS*
Symbol Parameter Value Unit Supply Voltage (Referenced GND) Input Voltage (Referenced GND) Vout Output Voltage (Referenced GND) Input Current, Iout Output Current, Supply Current, Pins Power Dissipation Still Air, Plastic Ceramic SOIC Package TSSOP Package Storage Temperature Tstg
This device contains protection circuitry guard against damage high static voltages electric fields. However, precautions must taken avoid applications voltage higher than maximum rated voltages this high-impedance circuit. proper operation, Vout should constrained range (Vin Vout) VCC. Unused inputs must always tied appropriate logic voltage level (e.g., either VCC). Unused outputs must left open.
Lead Temperature, from Case Seconds Plastic DIP, SOIC TSSOP Package Ceramic
Maximum Ratings those values beyond which damage device occur. Functional operation should restricted Recommended Operating Conditions. Derating Plastic DIP: mW/_C from 125_C Ceramic DIP: mW/_C from 100_ 125_C SOIC Package: mW/_C from 125_C TSSOP Package: mW/_C from 125_C high frequency heavy load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
Symbol Parameter Unit Supply Voltage (Referenced GND) Vin, Vout Input Voltage, Output Voltage (Referenced GND) Operating Temperature, Package Types Input Rise Fall Time (Figure 1000
RECOMMENDED OPERATING CONDITIONS
High-Speed CMOS Logic Data DL129
MC54/74HC08A
CHARACTERISTICS (Voltages Referenced GND)
|Iout| 2.4mA |Iout| 4.0mA |Iout| 5.2mA |Iout| 2.4mA |Iout| 4.0mA |Iout| 5.2mA Guaranteed Limit 25°C 1.50 2.10 3.15 4.20 0.50 0.90 1.35 1.80 2.48 3.98 5.48 0.26 0.26 0.26 ±0.1 85°C 1.50 2.10 3.15 4.20 0.50 0.90 1.35 1.80 2.34 3.84 5.34 0.33 0.33 0.33 ±1.0 125°C 1.50 2.10 3.15 4.20 0.50 0.90 1.35 1.80 2.20 3.70 5.20 0.40 0.40 0.40 ±1.0 Unit
Symbol
Parameter Minimum High-Level Input Voltage
Condition Vout 0.1V -0.1V |Iout| 20µA
Maximum Low-Level Input Voltage
Vout 0.1V 0.1V |Iout| 20µA
Minimum High-Level Output Voltage
|Iout| 20µA =VIH
Maximum Low-Level Output Voltage
|Iout| 20µA
Maximum Input Leakage Current Maximum Quiescent Supply Current (per Package)
Iout
NOTE: Information typical parametric values found Chapter Motorola High-Speed CMOS Data Book (DL129/D).
CHARACTERISTICS 50pF, Input 6ns)
Symbol tPLH, tPHL Parameter Maximum Propagation Delay, Input Output (Figures Guaranteed Limit 25°C 85°C 125°C Unit
tTLH, tTHL
Maximum Output Transition Time, Output (Figures
Maximum Input Capacitance
NOTE: propagation delays with loads other than information typical parametric values, Chapter Motorola High- Speed CMOS Data Book (DL129/D). Typical 25°C, Power Dissipation Capacitance (Per Buffer)* Used determine no-load dynamic power consumption: load considerations, Chapter Motorola High-Speed CMOS Data Book (DL129/D).
High-Speed CMOS Logic Data DL129
MC54/74HC08A
INPUT tPLH OUTPUT tTLH
tPHL
tTHL
Figure Switching Waveforms
TEST POINT OUTPUT DEVICE UNDER TEST
*Includes probe capacitance
Figure Test Circuit
Figure Expanded Logic Diagram (1/4 Device)
High-Speed CMOS Logic Data DL129
MC54/74HC08A
OUTLINE DIMENSIONS
SUFFIX CERAMIC PACKAGE CASE 632-08 ISSUE
-A14 NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: INCH. DIMENSION CENTER LEAD WHEN FORMED PARALLEL. DIMESNION NARROW 0.76 (0.030) WHERE LEAD ENTERS CERAMIC BODY. INCHES 0.750 0.785 0.245 0.280 0.155 0.200 0.015 0.020 0.055 0.065 0.100 0.008 0.015 0.125 0.170 0.300 0.020 0.040 MILLIMETERS 19.05 19.94 7.11 6.23 5.08 3.94 0.39 0.50 1.40 1.65 2.54 0.21 0.38 4.31 3.18 7.62 0.51 1.01
-TSEATING PLANE
0.25 (0.010)
0.25 (0.010)
SUFFIX PLASTIC PACKAGE CASE 646-06 ISSUE
NOTES: LEADS WITHIN 0.13 (0.005) RADIUS TRUE POSITION SEATING PLANE MAXIMUM MATERIAL CONDITION. DIMENSION CENTER LEADS WHEN FORMED PARALLEL. DIMENSION DOES INCLUDE MOLD FLASH. ROUNDED CORNERS OPTIONAL. INCHES 0.715 0.770 0.240 0.260 0.145 0.185 0.015 0.021 0.040 0.070 0.100 0.052 0.095 0.008 0.015 0.115 0.135 0.300 0.015 0.039 MILLIMETERS 18.16 19.56 6.10 6.60 3.69 4.69 0.38 0.53 1.02 1.78 2.54 1.32 2.41 0.20 0.38 2.92 3.43 7.62 0.39 1.01
SEATING PLANE
High-Speed CMOS Logic Data DL129
MC54/74HC08A
OUTLINE DIMENSIONS
SUFFIX PLASTIC SOIC PACKAGE CASE 751A-03 ISSUE
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSIONS INCLUDE MOLD PROTRUSION. MAXIMUM MOLD PROTRUSION 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.127 (0.005) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION.
0.25 (0.010)
SEATING PLANE
0.25 (0.010)
MILLIMETERS 8.75 8.55 4.00 3.80 1.75 1.35 0.49 0.35 1.25 0.40 1.27 0.25 0.19 0.25 0.10 5.80 6.20 0.25 0.50
INCHES 0.337 0.344 0.150 0.157 0.054 0.068 0.014 0.019 0.016 0.049 0.050 0.008 0.009 0.004 0.009 0.228 0.244 0.010 0.019
SUFFIX PLASTIC TSSOP PACKAGE CASE 948B-03 ISSUE
0.200 (0.008)
IDENTIFICATION
NOTES: DIMENSIONING TOLERANCING ANSI Y14.5M, 1982. CONTROLLING DIMENSION: MILLIMETER. DIMENSION DOES INCLUDE MOLD FLASH, PROTRUSIONS GATE BURRS. MOLD FLASH GATE BURRS SHALL EXCEED 0.15 (0.006) SIDE. DIMENSION DOES INCLUDE INTERLEAD FLASH PROTRUSION. INTERLEAD FLASH PROTRUSION SHALL EXCEED 0.25 (0.010) SIDE. DIMENSION DOES INCLUDE DAMBAR PROTRUSION. ALLOWABLE DAMBAR PROTRUSION SHALL 0.08 (0.003) TOTAL EXCESS DIMENSION MAXIMUM MATERIAL CONDITION. TERMINAL NUMBERS SHOWN REFERENCE ONLY. DIMENSIONS DETERMINED DATUM PLANE -U-.
0.100 (0.004) SEATING
PLANE
SECTION
MILLIMETERS 5.10 4.30 4.50 1.20 0.05 0.25 0.45 0.55 0.65 0.50 0.60 0.09 0.24 0.09 0.18 0.16 0.32 0.16 0.26 6.30 6.50
INCHES 0.200 0.169 0.177 0.047 0.002 0.010 0.018 0.022 0.026 0.020 0.024 0.004 0.009 0.004 0.007 0.006 0.013 0.006 0.010 0.248 0.256
High-Speed CMOS Logic Data DL129
MC54/74HC08A
Motorola reserves right make changes without further notice products herein. Motorola makes warranty, representation guarantee regarding suitability products particular purpose, does Motorola assume liability arising application product circuit, specifically disclaims liability, including without limitation consequential incidental damages. "Typical" parameters which provided Motorola data sheets and/or specifications vary different applications actual performance vary over time. operating parameters, including "Typicals" must validated each customer application customer's technical experts. Motorola does convey license under patent rights rights others. Motorola products designed, intended, authorized components systems intended surgical implant into body, other applications intended support sustain life, other application which failure Motorola product could create situation where personal injury death occur. Should Buyer purchase Motorola products such unintended unauthorized application, Buyer shall indemnify hold Motorola officers, employees, subsidiaries, affiliates, distributors harmless against claims, costs, damages, expenses, reasonable attorney fees arising directly indirectly, claim personal injury death associated with such unintended unauthorized use, even such claim alleges that Motorola negligent regarding design manufacture part. Motorola registered trademarks Motorola, Inc. Motorola, Inc. Equal Opportunity/Affirmative Action Employer.
Mfax trademark Motorola, Inc. reach EUROPE Locations Listed: Motorola Literature Distribution; P.O. 5405, Denver, Colorado 80217. 1-303-675-2140 1-800-441-2447 Customer Focus Center: 1-800-521-6274 MfaxTM: RMFAX0@email.sps.mot.com TOUCHTONE 1-602-244-6609 ASIA/PACIFIC: Motorola Semiconductors H.K. Ltd.; Ping Industrial Park, Motorola Back System Canada ONLY 1-800-774-1848 Ting Road, N.T., Hong Kong. 852-26629298 http://sps.motorola.com/mfax/ HOME PAGE: http://motorola.com/sps/ JAPAN: Nippon Motorola Ltd.: SPD, Strategic Planning Office, 141, 4-32-1 Nishi-Gotanda, Shagawa-ku, Tokyo, Japan. 03-5487-8488
High-Speed CMOS Logic Data DL129
MC74HC08A/D
Other recent searches
REJ03F0062-0100Z - REJ03F0062-0100Z REJ03F0062-0100Z Datasheet
MJE5740 - MJE5740 MJE5740 Datasheet
KIA7125FV - KIA7125FV KIA7125FV Datasheet
K4D261638E - K4D261638E K4D261638E Datasheet
GS2962 - GS2962 GS2962 Datasheet
FSQ510 - FSQ510 FSQ510 Datasheet
FSQ510H - FSQ510H FSQ510H Datasheet
FSF150D - FSF150D FSF150D Datasheet
FSF150R - FSF150R FSF150R Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
