Complete Resistor Products Solutions CTS, world leader design man
|
|
|
Top Searches for this datasheet
ELECTROCOMPONENTS
Complete Resistor Products Solutions
CTS, world leader design manufacture resistor products, consistently industry development thick film materials introduction standard package configurations. utilizing latest electronic technology, such (Electronic Data Interchange), established maintained shortest lead times industry. Most resistor network users, including largest most demanding, exempt products from incoming quality testing. These exemptions generate significant savings customers without tradeoff quality performance. solid ceramic resistor products have proven reliability that made world leader design manufacture quality resistor products. accumulated excess 1,965,920,560 hours life test data with percent confidence level failure rate only 0.000397 percent. That's reliability! It's standard others strive meet. Resistor/Electrocomponents registered 9001/ 9000 manufacturer. CTS's dedication continuous improvement corrective action programs insure resistor products meet customer expectations quality, performance service. Application Specific Resistor Products readily available from CTS. Typically, there engineering tooling charges supply Application Specific device meet special needs customer. Best all, manufacturing lead times Application Specific Resistor Products same standard products.
Catalog Updates
Resistor/Electrocomponents catalog World Wide www.ctscorp.com. This version catalog regularly updated incorporate product introductions.
Advantages Solid Ceramic Resistor Products
"solid ceramic" resistor products have been manufactured since 1963. These resistor products have excellent performance characteristics proven reliability that make resistor network industry leader. solid ceramic construction even more advantageous surface mounting. Resistor products used surface mounted applications exposed temperature extremes during manufacturing, aggressive cleaning procedures thereafter. There material interfaces permit entry harmful liquids with piece ceramic body. Solid ceramic construction allows substrates that physically larger than those used manufacturers "insert molded" devices without increasing overall package size. This allows products operate higher temperatures than similar sized molded products. design characteristics that allow solid ceramic products operate higher temperatures translate into long term reliability.
Internal Dendrite Growth Products
Metal migration, commonly called dendrite growth, classic cause internal shorting electronic devices when silver and/or lead present. mechanism dendrite growth includes voltage potential between metal electrodes presence moisture. Failure occurs after moisture penetrates body molded network during thermal shock soldering aqueous cleaning process. Because does include plastic molded outer package, solid ceramic construction will support internal dendrite growth. solid ceramic resistor products offer approximately percent more internal surface area resistor network design than comparably sized molded products. This extra design space allows provide many custom circuit designs that possible with molded products.
Committed Consistently Manufacturing High-Quality Products
certified Class MRPII user, which assures customers that systems place allow offer shortest lead times industry meet delivery promises every time. good environmental citizen. eliminated Ozone Depleting Substances from manufacturing operations.
Surface Mount Chips Chip Arrays
Series Description
Leadless Chip Array Leadless Chip Array Leadless Chip Array Leadless Chip Array Leadless Chip Array
Pads Available
4-8-16
Resistor Power@70°C
0.063W 0.100W 0.125W 0.063W 0.031W
Area
0.0074-028 013-026 018-036
Area
4.9-17.8 8.5-16.7 11.8-23.1 28.4
Comments
General Purpose, Power, Cost, Isolated Resistors General Purpose, Power, Cost, Isolated Resistors General Purpose, Power, Cost, Isolated Resistors General Purpose, Power, Cost, Bussed Resistors General Purpose, Power, Cost, Bussed Resistors
Pages
Resistor Products Selection Guide
Table Contents
Chip Resistor Arrays 742-746 .6-9 Surface Mount Series .10-11
Surface Mount Networks
Series Description
Leadless Network Leadless Network (.150 in.) Narrow Body (.220 in.) Medium Body (.220 in.) Medium Body
Surface Mount Series .12-13 Surface Mount Series .14-15
Leads/Pads Available
8-9-10-12 16-18 20-24 8-9-10-12 16-18 20-24 8-14-16 14-16 14-16-20
Package Power@70°C
0.8-1.3W 0.4-0.55W 0.60-1.2W 1.0-1.5W 1.0-2.0W
Area
0.06-.08 0.03-.04 0.06-.12 0.15-.17 0.15-.20
Area
Comments
Inductance, Capacitance, High Power, High Density, Application Specific Schematics Available Inductance, Capacitance, High Power, High Density, Application Specific Schematics Available Wave Reflow Solder, High Density, Application Specific Schematics Available Cost, Reflow Solder, High Density, Application Specific Schematics Available Cost, Wave Reflow Solder, Application Specific Schematics Available
Pages
16-17 18-19 10-11 12-13 14-15
Surface Mount Series .16-17 Surface Mount Series .18-19 Terminators.20-21 Series .22-23 Network Application Notes .24-25 Thick Film Pointing Device Series TrackStik® .26-29 Series SurfStik® .30-31 Dual Terminator Resistor Values .32-33 Surface Mount Land Patterns.34-35 Standard Packaging .36-37 Environmental Performance Specifications .38-39 Sales Offices.40-43
Through Hole Networks
Series Description
Conformal Network
specifications subject change without notice. Catalog 3756E
Leads Available
Package Power@70°C
0.4-1.35W
Area
0.04-.12
Area
26-78
Comments
Cost, Power Network
Pages
22-23
Check Website latest specifications product information.
Concave Chip Resistor Arrays Series 742-745
(Ohms) Code (Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 22000 27000 33000 39000 47000 51000 56000 68000 82000 100000 110000 120000 150000 180000 220000 270000 330000 390000 470000 510000 560000 680000 820000 1000000
Standard Packages Style Codes
Concave Termination
pitch (0.8mm) pitch (1.27mm) pitch (1.27mm) pitch (1.27mm) Mark (Dot) Mark (Triangle)
Thick Film Chip Resistor Arrays cost High density packaging Leadless surface mount construction Tape reel packaging Solder-coated nickel barrier pads Isolated bussed circuits Compatible with solder processes Wave, reflow, Vapor phase reflow High Density Packaging: less space resistor than 0603 chip resistors. less space resistor than 0805 chip resistors. Placement Efficiency: Arrays require fewer placements than discrete components. Larger overall size eases handling compared discrete components. Profile: used PCMCIA cards Resistance Tolerance: Standard: (whichever greater) Operating Temperature Range: -55°C +125°C Temperature Coefficient (TCR): Standard: 200PPM/°C
742C043 Resistors Terminations
742C083 Resistors Terminations
742C163 Resistors Terminations
743C043 Resistors Terminations
743C083 Resistors Terminations
744C043 Resistors Terminations
744C083 Resistors Terminations
Package Outlines
Concave Termination Type
Termination Area (all places) Dimensions: inch Series Area (in2) Resistor Circuit Type
745C101 Resistors Terminations
745C102 Resistors Terminations
Resistance Range
70°C Power Resistor*
Maximum Operating Voltage
742C 743C 744C 745C
0.0037 0.0071 0.0094 0.0058
Isolated Isolated Isolated Bussed
100K
0.063W 0.100W 0.125W 0.063W
100V 200V
Total package power equals total number resistors times rated power resistor.
Power Derating Land Patterns Packaging
page pages 34-35 pages 36-37
Size Code Part Circuit Code Pads Res.
Isolated Isolated
1.60±0.20 0.063±.008
Environmental Performance Specifications
pages 38-39
mounting surface will affect long term reliability solder joint between Series 742-745 mounting surface. Application requirements vary each user must determine Series 742-745 appropriate application.
1000 1100 1500 1800 2200 2700 *50m
000X
0603 742C043 0603 742C083 0603 742C163 0805 743C043 0805 743C083 1206 744C043 1206 744C083 1203 745C101 745C102
+0.10 3.20±0.20 1.60±0.20 0.80±0.05 0.60 ±0.25 0.5±0.15 0.30±0.20 0.40±0.15 0.126±.008 0.063±.008 0.032±.002 +.004 0.020±.006 0.012±.008 0.016±.006 0.024 .010 6.40±0.20 Isolated 0.252±.008 2.54±0.20 0.100±.008 2.0±0.20 1.27±0.05 0.60±0.10 0.80±0.15 0.40±0.30 0.55±0.15 5.08±0.30 0.079±.008 0.050±.002 0.024±.004 0.031±.006 0.016±.012 0.022±.006 0.200±.012 2.54±0.20 0.100±.008
Order Chip Resistor Arrays
742C
Series 742C 743C 744C 745C
Isolated Isolated Isolated
Terminations (742 only) (745 only)
3.20±0.20 1.27±0.05 0.60±0.10 0.80±0.15 0.50±0.30 0.55±0.15 5.08±0.30 0.126±.008 0.050±.002 0.024±.004 0.031±.006 0.020±.012 0.022±.006 Isolated 0.200±.012 Bussed 6.40±0.20 3.10±0.20 1.27±0.05 0.60±0.15 0.60±0.15 0.35±0.15 0.55±0.15 0.252±.008 0.122±.008 0.050±.002 0.024±.006 0.024±.006 0.014±.006 0.022±.006
Resistor Code Digit Code digit Code
Tolerance (Standard) F=±1% Zero Jumper
Schematic Bussed (745) Bussed (745 only) Isolated (742, 743, 744)
NOTE: dashes spaces appear part number. Example: 742C083101J page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 74XCB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 74XCB
Convex Chip Resistor Arrays Series 742, 745,
(Ohms) Code (Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 22000 27000 33000 39000 47000 51000 56000 68000 82000 100000 110000 120000 150000 180000 220000 270000 330000 390000 470000 510000 560000 680000 820000 1000000
Package Outlines
Standard Packages Style Codes
Convex Termination
pitch (1.27mm) Common Designator
Convex Termination Type Thick Film Chip Resistor Arrays cost High density packaging Leadless surface mount construction Tape reel packaging Solder-coated nickel barrier pads Isolated bussed circuits Compatible with solder processes reflow, Vapor phase reflow High Density Packaging: less space resistor than 0603 chip resistors less space resistor than 0805 chip resistors Placement Efficiency: Arrays require fewer placements than discrete components. Larger overall size eases handling compared discrete components. Profile: used PCMCIA cards Resistance Tolerance: Standard: (whichever greater) Operating Temperature Range: -55°C +125°C Temperature Coefficient (TCR): Standard: 200PPM/°C
Size Code Part Circuit Code Pads Res.
Isolated
Dimensions:
inch
Termination Area (all places) 745X101 Resistors Terminations 745X102 Resistors Terminations
Note: Marking Concept Convex Concave Series Different.
Power Derating Land Patterns Packaging Environmental Performance Specifications
page pages 34-35 pages 36-37
pages 38-39
mounting surface will affect long term reliability solder joint between Series 742, 745, mounting surface. Application requirements vary each user must determine Series 742, 745, appropriate application.
0603 742X083 745X101 1203 745X102 0603 746X101
1.6±0.2 0.8±0.05 0.5±0.1 0.5±0.15 0.3±0.15 0.3±0.15 3.2±0.2 0.126±008 0.063±008 0.032±002 0.020±004 0.020±006 0.012±006 0.024±006
1000 1100 1500 1800 2200 2700 *50m
000X
6.4±0.2 3.2±0.2 1.27±0.05 0.6±0.1 0.9±0.15 0.5±0.2 0.5±0.15 1.1±0.15 Bussed 0.252±008 0.126±008 0.050±002 0.024±004 0.035±006 0.020±008 0.020±006 0.043±006 Bussed 3.3±0.1 1.65±0.15 0.64±0.05 0.6±0.1 0.35±0.05 0.4±0.10 0.45±0.10 0.5±0.05 0.130±004 0.065±006 0.025±002 0.024±004 0.014±002 0.016±004 0.018±004 0.020±002
Order Chip Resistor Arrays
742X
Series 742X 745X 746X
Series
Area (in2) Resistor
Circuit Type
Resistance Range
70°C Power Resistor*
Maximum Operating Voltage
Terminations (745 only)
Resistor Code Digit Code Digit Code Tolerance (Standard) F=±1% Zero Jumper
742X 745X 746X
0.0037 0.0058 0.0013
Isolated Bussed Bussed
100K 100K
0.063W 0.063W 0.031W
Schematic Bussed (745 only) Bussed (745 only) Isolated (742)
NOTE: dashes spaces appear part number. Example: 742X083101J
Total package power equals total number resistors times rated power resistor.
page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 74XXCB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 74XXCB
Surface Mount Series
Bussed Schematic
(Ohms) Code 000X
1000 1100 1200 1500 1800 2000 2200 2700
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 56000 68000 82000 100000 110000 120000 150000 180000 200000 220000 270000 330000 390000 470000 560000 680000 820000 1000000
0.20 -0.03 0.008 +0.002
-0.001
+0.05
DIM.
Narrow Body Design Series requires less board space than molded products same power rating Packaged tape reel slide packs Solid ceramic construction Meets SOGN-0001 outline internal dendrite growth Application specific circuits available Compatible with solder processes Wave, reflow, Vapor phase reflow Recommended bottom side attachment Resistance Range: Standard: Resistance Tolerance: Standard: (whichever greater) Special: ±0.25% (whichever greater) Maximum Operating Voltage: exceed rated power Temperature Coefficient: Standard: ±100PPM/°C typical ±200PPM/°C typical Operating Temperature Range: -55°C +125°C Dielectric Strength: Power Rating (Total Network Power): @25°C 0.9w 1.6w 1.8w @70°C 0.6w 1.0w 1.2w Maximum Resistor Power: (not exceed total network power) Schematic @25°C 0.12w 0.24w 0.12w 0.12w @70°C 0.08w 0.16w 0.08w 0.08w
0.81 -0.31 0.032 +0.013
+0.33
6.000 ±0.20 0.236 ±0.008
PART DATE
3.90 0.154
±0.10 ±0.004
Isolated Schematic
-0.012
BELOW SEATING PLANE
MARK
Dual Terminator Schematic
INSULATION COATING APPLIED SURFACES
0.51 TYP. 0.020
1.55 ±0.20 0.061 ±0.008
0.43 0.017
±0.05 ±0.002
0.180 ±0.08 0.007 ±0.003 1.27 TYP. 0.050
Note
R/2R Ladder Schematic
Pins
Dimension
Notes: Lead COPLANARITY 0.10 MAX. 0.004 inch DIMENSIONS EQUIVALENT General Tolerances ±0.25 inch ±0.010 Dimensions mm/in.
4.90 0.10 0.193 0.004 8.65 0.10 0.340 0.004 9.90 0.10 0.390 0.004 0.005
Order Products
Series
Reel Size dia. dia.
Application Notes pages 24-25 Power Derating Land Patterns Packaging Environmental Performance Specifications page pages 34-35 pages 36-37
Number Pins Schematic Bussed Isolated Dual Terminator Ladder
Resistor Code Page Schematic Tolerance Schematic ±1/2%
Packaging Tape Reel Slide Pack (see page
Schematic
Schematic
schematic ±1LSB products ±1/2LSB tolerance. (LSB=Least Significant Bit)
page part marking information.
pages 38-39
NOTE: dashes spaces appear part number. Example: 766143101GTR13
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 766B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 766B
Surface Mount Series
Bussed Schematic
(Ohms) Code
1000 1100 1200 1500 1800 2000 2200 2700 000X
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 56000 68000 82000 100000 110000 120000 150000 180000 200000 220000 270000 330000 390000 470000 560000 680000 820000 1000000
0.20 0.008
+0.05 -0.03 +0.002 0.001
DIM.
Ample Space Between Body Board Having ample space between body board allows fast, thorough cleaning after soldering, ease solder joint inspection. 0.220" wide body Solid ceramic construction internal dendrite growth Clearance ease board cleaning 0.030" Compatible with PDP-100 SOGN-0002 24mm tape reel slide packs Application specific circuits available Compatible with solder processes Wave, reflow, Vapor phase reflow Resistance Range: Standard: Resistance Tolerance: Standard: (whichever greater) Special: ±0.25% (whichever greater) Maximum Operating Voltage: exceed rated power Temperature Coefficient: Standard: ±100PPM/°C typical ±200 PPM/°C typical Operating Temperature Range: -55°C +125°C Dielectric Strength: Power Rating (Total Network Power): @25°C 2.0w 2.3w @70°C 1.3w 1.5w Maximum Resistor Power: (not exceed total network power) Schematic @25°C 0.15w 0.3w 0.15w 0.15w @70°C 0.1w 0.2w 0.1w 0.1w
0.81 -0.31 0.032 +0.013
+0.33
-0.012
7.62 0.300
PART DATE
5.59 -0.30 0.220 +0.005
+0.13
Isolated Schematic
-0.010
BELOW SEATING PLANE
MARK
Dual Terminator Schematic
INSULATION COATING APPLIED SURFACES 2.16 ±0.20 0.085 ±0.008
MAX. TYP. 0.053 0.760 ±0.13 0.030 ±0.005
NOTE 0.43 ±0.05 0.017 ±0.002 1.27 TYP. 0.050
R/2R Ladder Schematic
Pins
Dimension
0.25 0.13 0.390 0.010 0.005 9.91 11.18 0.25 0.13 0.440 0.010 0.005
Notes: Lead COPLANARITY 0.10 MAX. 0.004 inch DIMENSIONS EQUIVALENT General Tolerances ±0.25 inch ±0.010 Dimensions mm/in.
Order Series Products
Application specific custom products marked with either customer part number non-descriptive part number. Send documentation Sales Office giving schematic, resistor values tolerance, other non-standard information. pages 24-25 application notes.
Series
Resistor Code Page Schematic Tolerance Schematic ±1/2%
Number Pins
Packaging Tape Reel Slide Pack (see page
Application Notes pages 24-25 Power Derating Land Patterns Packaging Environmental Performance Specifications page pages 34-35 pages 36-37
Schematic
Bussed Isolated Dual Terminator Ladder
pages 38-39
NOTE: dashes spaces appear part number. Example: 767143101GTR
Schematic schematic products (not marked) tolerance.
Schematic ±1LSB ±1/2LSB (LSB=Least Significant Bit)
page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 767B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 767B
Surface Mount Series
Bussed Schematic
(Ohms) Code
1000 1100 1200 1500 1800 2000 2200 2700 000X
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 56000 68000 82000 100000 110000 120000 150000 180000 200000 220000 270000 330000 390000 470000 560000 680000 820000 1000000
0.20 -0.03 0.008 +0.002 -0.001
+0.05
DIM.
Medium Body, Small Outline Products profile-board network clearance 0.005"/0.010" Conforms PDP-100 SOGN-0002 24mm tape reel slide Application specific circuits available internal dendrite growth Compatible with solder processes Wave, reflow, Vapor phase reflow Recommended bottom side attachment Resistance Range: Standard: Resistance Tolerance: Standard: (whichever greater) Special: ±0.25% (whichever greater) Maximum Operating Voltage: exceed rated power Temperature Coefficient: Standard: ±100PPM/°C typical ±200 PPM/°C typical Operating Temperature Range: -55°C +125°C Dielectric Strength: Power Rating (Total Network Power): @25°C 2.0w 2.3w 3.0w @70°C 1.5w 2.0w Maximum Resistor Power: (not exceed total network power) Schematic @25°C 0.15w 0.3w 0.15w 0.15w @70°C 0.1w 0.2w 0.1w 0.1w
Isolated Schematic
0.81 0.032
+0.33 0.30 +0.013 0.012
7.62 0.300
PART DATE
5.59 0.220
+0.13 0.25 +0.005 0.010
BELOW SEATING PLANE
MARK
Dual Terminator Schematic
INSULATION COATING APPLIED SURFACES 1.60 ±0.20 0.063 ±0.008
1.35 MAX. TYP. 0.053
±0.06 0.19 0.0075 ±0.0025
NOTE
0.43 ±0.05 0.017 ±0.002
1.27 TYP. 0.050
R/2R Ladder Schematic
Pins
Dimension
Notes: Lead COPLANARITY 0.10 MAX. 0.004 inch DIMENSIONS EQUIVALENT General Tolerances ±0.25 inch ±0.010 Dimensions mm/in.
9.91 0.390 11.18
0.25 0.13 0.010 0.005 0.25 0.13 0.010 0.005 0.25 0.13 0.010 0.005
Order Series Products
Application specific custom products marked with either customer part number non-descriptive part number. Send documentation Sales Office giving schematic, resistor values tolerance, other non-standard information. pages 24-25 application notes.
Series
Resistor Code Page Schematic
0.440 13.70 0.540
Application Notes pages 24-25 Power Derating Land Patterns Packaging Environmental Performance Specifications page pages 34-35 pages 36-37
Number Pins Schematic Bussed Isolated Dual Terminator Ladder
Packaging Tape Reel Slide Pack (see page
Tolerance Schematic ±1/2%
Schematic schematic products tolerance. (not marked)
Schematic ±1LSB ±1/2LSB (LSB=Least Significant Bit)
pages 38-39
NOTE: dashes spaces appear part number. Example: 768143101GTR page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 768B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 768B
Surface Mount Series
Bussed Schematic
(Ohms) Code
1000 1100 1200 1500 1800 2000 2200 2700
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 56000 68000 82000 100000 110000 120000 150000 180000 200000 220000 270000 330000 390000 470000 560000 680000 820000 1000000
Single Termination (SRT)
MARK
PART DATE 2.03 ±0.12 0.080 ±0.005 2.41 ±0.12 0.095 ±0.005
In-Line Surface Mount Resistor Products High density packaging profile Input/outputs available: Dual Terminations Single Terminations Nickel barrier solder-coated pads Designed visual inspection solder joints Designed board cleaning 24mm tape reel packaging Application specific circuits available Compatible with solder processes Wave, reflow, Vapor phase reflow Resistance Range: Standard: Resistance Tolerance: Standard: (whichever greater) Special: (whichever greater) Maximum Operating Voltage: exceed rated power Temperature Coefficient: Standard: ±200PPM/°C Special: ±100PPM/°C Meg) Dielectric Strength: Operating Temperature Range: -55°C +125°C Power Rating (Total Network Power): Number input/outputs (watts) @25°C @70°C 0.85 0.95 Maximum Resistor Power: (Not Exceed Total Network Power) Bussed Dual Isolated Terminator Schematic Schematic @25°C 0.12w 0.24w @70°C 0.08w 0.16w
Bussed Schematic
0.05 ±0.05 0.002 ±0.002 1.52 0.060 0.64 ±0.12 0.025 ±0.005 SEATING PLANE
Dimensions mm/in.
Input/Outputs Dim.
Isolated Schematic
11.81 ±0.12 13.08 ±0.12 14.35 ±0.12 16.89 ±0.12
0.465 ±0.005 0.515 ±0.005 0.565 ±0.005 0.665 ±0.005
Available
1.27 TYP. 0.050
11.81 ±0.12 13.08 ±0.12 14.35 ±0.12 16.89 ±0.12
0.465 ±0.005 0.515 ±0.005 0.565 ±0.005 0.665 ±0.005
Isolated Schematic
Available
Dual Termination (DRT)
MARK
PART DATE
2.03 ±0.12 0.080 ±0.005
2.41 ±0.12 0.095 ±0.005
Dual Terminator Schematic
0.05 0.002
±0.05 ±0.002
SEATING PLANE
Available
Values Code listed page
1.52 0.060 0.64 ±0.12 0.025±0.005
Order Series Products
Application specific custom products marked with either customer part number non-descriptive part number. Send documentation Sales Office giving schematic, resistor values tolerance, other non-standard information. pages 24-25 application notes.
Series
Resistor Code Page Schematic
1.27 TYP. 0.050
mounting surface will affect long term reliability solder joint between Series mounting surface. Application requirements vary each user must determine whether Series appropriate application. Thermal shock data solder joint fatigue available request.
Application Notes pages 24-25 Power Derating Land Patterns Packaging Environmental Performance Specifications page pages 34-35 pages 36-37
Input/Outputs Schematic
Packaging Tape Reel Bulk (see page
Bussed Isolated Dual Terminator
Tolerance Schematic ±1/2%
Schematic schematic products tolerance. (not marked)
pages 38-39
NOTE: dashes spaces appear part number. Example: 752163101GTR page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 752B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 752B
Surface Mount Series
Bussed Schematic
(Ohms) Code
1000 1100 1200 1500 1800 2000 2200 2700
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 56000 68000 82000 100000 110000 120000 150000 180000 200000 220000 270000 330000 390000 470000 560000 680000 820000 1000000
Single Termination (SRT)
MARK
Dual Termination (DRT)
MARK
In-Line Surface Mount Resistor Products High density packaging Solid ceramic construction profile Available terminations package: Dual Terminations Single Terminations Solder-coated pads Designed visual inspection solder joints Designed board cleaning 16mm tape reel packaging Resistance Range: Standard: Resistance Tolerance: Standard (whichever greater) Special: (whichever greater) Maximum Operating Voltage: exceed rated power Temperature Coefficient: Standard: ±200PPM/°C Operating Temperature Range: -55°C +125°C Power Rating (Total Network Power): Number input/outputs @25°C 0.60 0.64 0.68 0.82 0.60 0.64 0.68 0.82 @70°C 0.40 0.43 0.45 0.55 0.40 0.43 0.45 0.55 Maximum Resistor Power: (Not Exceed Total Network Power) Bussed Dual Isolated @25°C 0.06w 0.12w @70°C 0.04w 0.08w
Bussed Schematic
PART IDENTIFICATION
PART IDENTIFICATION
Isolated Schematic
Available
Isolated Schematic
Available
Seating Plane
Seating Plane
Dual Terminator Schematic
Terminations Dim. Dimension ±0.12 ±0.005
Available
Values Code listed page
2.41±0.12 2.03±0.12 0.64±0.12 0.71±0.12 0.33±0.08 0.08±0.08 0.89 Ref.
0.095±0.005 0.080±0.005 0.025±0.005 0.028±0.005 0.013±0.003 0.003±0.003 0.035 Ref.
6.22 6.86 7.49 8.76 6.22 6.86 7.49 8.76
0.245 0.270 0.295 0.345 0.245 0.270 0.295 0.345
Order Series Products
Application specific custom products marked with either customer part number non-descriptive part number. Send documentation Sales Office giving schematic, resistor values tolerance, other non-standard information. pages 24-25 application notes.
Series
Terminations
Resistor Code Page Schematic
mounting surface will affect long term reliability solder joint between Series mounting surface. Application requirements vary each user must determine whether Series appropriate application. Thermal shock data solder joint fatigue available request.
Application Notes pages 24-25 Power Derating Land Patterns Packaging Environmental Performance Specifications page pages 34-35 pages 36-37
Packaging Tape Reel Bulk (see page
pages 38-39
NOTE: dashes spaces appear part number.
Schematic Bussed Isolated (not available I/Os) Dual Terminator available I/Os.)
Example: 753163101GTR
Tolerance
schematic products tolerance. (not marked)
page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 753B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 753B
pages 16-19 physical dimensions, power rating other information. Termination
Spice Equivalent Circuit
Terminator Resistance Value/2
High Speed Digital Termination Networks inductance leadless construction Excellent high frequency response Very crosstalk High power dissipation versus board space Spice models available circuit simulation Solder-coated nickel barrier pads Tape reel packaging Designed work with standard automated surface mount pick place solder processes Resistance Tolerance: Standard (whichever greater) Special: Temperature Coefficient (TCR): Standard: ±200PPM/°C Operating Temperature Range: -55°C +125°C
0.5nH
0.5nH 0.08pF 0.1pF 0.6nH
0.5nH 0.08pF 0.1pF
0.08pF
0.1pF
Termination
0.2nH Apply 250mV Spice Result Measured Result Spice Result 28pS Measured Result 28pS 0.2nH 0.6nH 0.2nH
Apply View View
Standard Resistance Values Standard Resistance Values
4.4mV 3.1mV 4.4mV 3.0mV 3.1mV 3.0mV
4.5mV 3.0mV 5.0mV 2.4mV 3.0mV 2.6mV
48mV 28mV 55mV 30mV 30mV 30mV
34mV 22mV 34mV 16mV 22mV 16mV
Testing based pulse using Tektronix 11802 digitizing scope. 28ps pulse applied, filter applied measurement. Terminator value tested
Value Code Value Code page available value codes
Thev
Code 500A 750B 101B 121B 121A 131A 181A 191A
Apply View View Apply View View
Order Series Products
Series Series
Pads (GTL) (ECL)
Resistor Code digit
page available value codes
Standard Product Offering Termination Type Series# Rated Package Power @25°C Resistor Power @25°C Term. Pitch Term. Lines
Packaging Tape Reel Bulk (see page
(parallel)
0.82W 2.0W 0.82W 2.0W
0.06W 0.08W 0.06W 0.08W
0.025" 0.050" 0.025" 0.050"
Termination G=GTL E=ECL
Tolerance (standard)
page part marking information.
(Thevenin)
NOTE: dashes spaces appear part number. Example: 75324G101GTR
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 75XB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 75XB
Single-In-Line Conformal Series
Bussed Schematic
2.41 MAX. 0.095 DIM. 4.95 MAX. 0.195 3.43 0.135
±0.25 ±0.010
(Ohms) Code
Available through Pins
(Ohms) Code
3300 3900 4700 5100 5600 6800 8200 10000 11000 12000 15000 18000 20000 22000 27000 33000 39000 47000 51000 56000 68000 82000 100000 110000 120000 150000 180000 220000 270000 330000 390000 470000 510000 560000 680000 820000 1000000
DATE
PART NUMBER
TYP. Available Pins
Profile Conformal Products CTS' expertise resistor network technology available space-saving conformal products. High-reliability cermet resistors Space saving over individual resistors Available even number pins from leads 2.54mm/100in. spacing Resistance Range: Standard: through Resistance Tolerance: Standard: (whichever greater) Maximum Operating Voltage: 100V exceed rated power Temperature Coefficient: ±100PPM/°C typical ±200PPM/°C typical Operating Temperature Range: -55°C +125°C Dielectric Strength:
0.25 -0.08 0.010 +0.005
0.003
+0.13
2.54 TYP. 0.100 1.24 MAX. 0.049
0.51 0.020
+0.13 -0.008 +0.005 -0.003
TYP.
1.02 TYP. 0.040
Isolated Schematic
NOTES: General Tolerances ±0.25 inch ±0.010
Dimensions mm/in. Copper Alloy Leads, Solder-coated Product Color Blue
Available Pins
Number Pins
Dimension ±0.25/0.010
Package Power @25°C
Package Power @70°C
Dual Terminator Schematic
Schematic
10.11/0.398 12.65/0.498 15.19/0.598 17.30/0.698 20.27/0.798 22.81/0.898 25.35/0.998 27.89/1.098 30.43/1.198
0.60 0.83 0.96 1.18 1.32 1.49 1.66 1.83 2.00W
Resistor Power @25°C
0.40 0.52 0.64 0.76 0.88 1.00 1.11 1.24 1.35
Resistor Power @70°C
1000 1100 1200 1500 1800 2200 2700
0.15 0.30
0.10 0.20
Order Series Products
Series
Power Derating Land Patterns Packaging Environmental Performance Specifications
page pages 34-35 pages 36-37 Schematic pages 38-39 Bussed Isolated Dual Terminator Resistor Code Schematics Resistor Value Schematic Example 220/330 220/330 standard part numbers Number Pins
NOTE: dashes spaces appear part number.
Example: 770103103
page part marking information.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 770B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 770B
Application Specific Products
Application specific resistor products readily available from provide designer with optimum performance cost effective solutions. There tooling engineering charges supply resistor products with application specific schematics. Lead times application specific products same standard manufactured products. Application specific products available 752, 753, 766, products. Examples Application Specific Products: Customer part number maintain design confidentiality. Multiple and/or non-standard resistor values. Resistor products designed capacitance inductance. Non-standard tolerances matching requirements. Non-standard schematics. Maximum operating voltage should specified each resistor when resistor value high enough supersede power rating. Crossovers should avoided. necessary, second level provided utilizing opposite side substrate surface. each resistor affected geometry resistor number resistor formulations required. tracking between resistors screened same time dependent comparative resistor length. ±200 considered standard multiple formulation products resistors ohms less. Buried nodes should avoided. Resistance values must read with special test equipment that result reduced measuring accuracy. tolerance each resistor should specified based circuit requirements. Resistor tolerance ±0.25% usually closest tolerance available. tolerance standard 752, 753, 766, products. Consult with factory prior finalization application specific products obtain optimum network design. table page shows general empirical rules which usually apply application specific schematics. Actual capabilities dependent required schematic should verified CTS.
Capability Guidelines Characteristics Thick Film Products 10-30 Resistance Ranges 31-99 100-1Meg
Best Absolute tolerance Ratio Match (50:1 ratio)* Parallel Circuit Resistance Tolerance(>50:1 ratio* Loop) Parallel Circuit Resistance Tolerance(<50:1 ratio* Loop) Best (-55°C +125°C) Best Tracking <3:1 ratio* (Same ink/same side) Best Tracking >3:1 ratio* (Same ink/same side) Maximum Resistor Power (Not exceed maximum package power)
±0.3 ±0.3 ±0.3 ±0.3 ±200PPM 75PPM 100PPM
±0.3 ±0.3 ±0.3 ±0.3 ±100PPM 50PPM 75PPM
±0.25% ±0.25% ±0.25% ±0.25% ±100PPM 50PPM 75PPM
(total package power) (Total number resistors) *Ratio Highest Resistance Value Lowest Resistance Value
Application Specific Schematics
Resistor values, tolerance, TCR, power rating circuit connections factors which determine resistor network design meet circuit designers' optimum performance cost goals. following information provided assist specifying application specific products which meet performance requirements lowest cost. Similar resistor values should grouped resistor network. Each group resistor values require different resistor formulation. Normally larger range resistor values obtained single resistor pin-outs selected network designer. Usually, three resistor formulations maximum that used network. Each formulation required will increase cost. power dissipation each resistor should specified based performance requirements. Total power must conform maximum package power specification unless specified which resistors operated given time.
Catalog Schematics
Bussed Schematic bussed schematic consists (N-1) resistors (with equal number pins) same value connected common buss. These products commonly used pull up/down resistors impedance matching terminating resistors. They also used other applications where circuit requires number same value resistors connected common point.
Dual Terminator Schematic
dual terminator schematic consists (2N-2) resistors different values with each resistor value connected common buss. resistor values form standard Thevenin equivalent resistance values which used termination different voltages. These products typically used termination.
Resistor Values Available
Resistor Values available selected networks current sensing applications.
Isolated Schematic isolated schematic consists (N/2) resistors same value which electrically isolated from each other. Normally these products used current limiting resistors termination resistors. They also used other applications where circuit requires number same value resistors which connect various points. Since resistors same network processed identically, isolated products have been used fabricate very accurate voltage dividers cost selectively connecting resistors series.
R/2R Schematic R/2R ladder network commonly used digital analog analog digital conversions successive steps. Input signals applied each ladder signal taken from output terminal where signal used drive operational amplifier. R/2R ladder products available with ladder accuracy ±1/2 (least significant bit) maximum bits bits.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com ASPB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com ASPB
Series TrackStik
Axis Ceramic Strain Gage Pointing Device Type 106B
View
0.30 0.15 0.012 0.006 Places) 2.00 0.08 0.079 0.003 Places) 9.00 0.354 2.36 0.08 Places) 0.093 0.003
Series TrackStik
Axis Ceramic Strain Gage Pointing Device
View
4.40 0.08 0.173 0.003 2.30 0.08 0.091 0.003
Bias 7.00 0.08 0.276 0.003 3.2K Bias
;;;;;;;
Features:
Smooth Motion Control Solid Ceramic Thick Film Strain Resistors Cost Pointing Solution Moving Mechanical Parts Durable Reliable Linear Repeatable Output Very Output Hysteresis Built Metallic Shield Proven Cermet Resistor Technology Patent Pending Construction
4.30 0.169
4.40 0.173 6.20 0.244 0.50 0.020 8.50 0.335 8.80 0.08 0.346 0.003 2.00 0.079 1.00 0.039 Flex Cable 4.50 0.08 0.177 0.003 9.00 0.08 0.354 0.003 3.56 0.005 0.140 +0.004
0.002 +0.100
2.50 0.098
Electrical Schematic
16.00 0.630 12.40 0.488
Chamfer
4.50 0.177
4.50 0.08 0.177 0.003
0.30 0.08 Places) 0.012 0.003
Applications:
Cursor Control Computer Display Directional Control Stick Applications Video Game Controllers
Plastic Adaptor Front View
2.60 0.102
Standard Resistance Value: 3.2K Standard Resistor Tolerance: ±5.0% Standard Resistance Match: ±1.0% Cycle Life: >8,000,000 cycles Maximum Force: Horizontal Vertical 10Kg Typical Output Characteristics: Axis 2.4µV/V/gram Axis 0.225µV/V/gram
0.51 0.020
1.55 Max. 0.061 6.12 0.200 0.241 0.008
Isometric View Scale
8.38 Max. 0.330
Stainless Steel Mounting Plate
3.71 0.146 4.78 0.188 1.50 0.08 0.059 0.003
0.38 Max. 0.015
Front View
1.93 0.08 0.076 0.003
Electrical Schematic
NOTES: General Tolerances ±0.25 inch ±0.010 Dimensions mm/in. Overall post heights achieved interchanging Plastic Adaptor Cap. output sensitivity dependent overall post height. actual assignment electrical schematic dependent configuration flex cable. Custom configurations base mounting plate, post height flex cable accommodated.
1.00 0.08 0.039 0.003
0.13 Chamfer 0.005 Places)
0.50 0.076 0.020 0.003
Bias 3.2K Bias
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 106B
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 108A
Series Pointing Device
Technology
strain gage resistors fabricated using conventional thick film ceramic processes. However, thick film resistor inks specially formulated sensitive mechanical stress. When resistor stressed, repeatable change resistance occurs. This resistance change associated with strain resistor negative under compression, positive under tension. pointing device constructed using square ceramic post with strain sensitive resistors located each side (north, south, east west). resistors strategically located maximum stress realized when pressure applied perpendicular post. typical pointing device application, resistors opposite sides ceramic post configured voltage divider circuits (north/south, east/west). output voltage each divider changes with respect applied force. Both direction force determined from output voltage dividers. There moving electromechanical components therefore mechanical components wear with these pointing devices.
Information
Temperature Sensitivity
pointing devices capable operating over temperature range -50°C +105°C. tracking strain resistors ppm. This gives worst case error less than 0.001% over operating temperature range. Maximum error output stage temperature change 0.4% with amplifier gain 400.
Control Circuitry
strain sensitive resistors arranged balanced bridge circuit pointing device. When force applied pointing stick, resistance changes proportion that force. That results voltage change that input micro controller which controls movement cursor. will recommend design components appropriate electronic control circuit upon request.
Connectors
Pointing sticks available either four connector configurations. connector option supplied single sided PWB, four connection requires sided PWB. Flex cables supplied with 1.0, connector pitch.
Hysteresis
hysteresis "repeatability error" resistors when configured voltage divider less than .0025%. Maximum hysteresis error output stage 1.0% with amplifier gain 400.
Order Series
pointing sticks manufactured customer order meet mounting dimensions customer's application. drawing sketch specifying desired mounting configuration required. Variations such height post, size mounting base shape flex cable optimized specific applications. application engineers available assist with your application. more information about products consult your local sales representative World Wide Web.
Circuit Stability Drift
Stability accuracy control circuit important during steady state condition when force applied stick. circuit drift that present during steady state condition could mistaken "movement" pointing device. advantageous perform "software calibration" microprocessor.
Flex Cables
Polyimide flex cables designed custom circuit routing available with pressure sensitive adhesive flex cable assembly. pitch different from connector end. Tooling required manufacture custom polyimide flex cables.
Output Linearity Calculation Angular Output
Output voltage divider circuit specified linear within ±1.0%. Actual output voltage calculated multiplying maximum output voltage cosine angle applied force.
Example Circuit Amplify Outputs
Strain Resistors
Strain Resistors
multi-turn multi-turn
(Rgain) VERTICAL OUTPUT
(Rgain) HORIZONTAL OUTPUT
G=400
G=400 Analog Devices AMP-04 inst.
Analog Devices AMP-04 inst.
NOTES: Vdivider
Vout (Vref-Vdivider) Output Change 9.2uV/gram Gain Gain
Adjust VREF volts output steady state position. Maximum swing output volts volts. resistors should metal film equivalent.
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com PSIB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com PSIB
Series SurfStik
Axis Ceramic Strain Gage Pointing Device
10.30 0.30 0.406 0.012 7.50 0.295
Features:
Compatible with Standard Surface Mount Process Compatible 105, Series TrackStik® Ultra Small Size Full Motion Control Durable Reliable Linear Repeatable Output Proven Cermet Resistor Technology
1.40 0.15 0.065 0.006
1.27 0.05 0.050 0.002 0.76 0.030
1.78 0.05 0.070 0.002 Square Substrate Surface Mount Base 0.25 0.010 2.23 0.088 5.26 0.25 0.207 0.010
7.50 0.295
5.48 0.216
0.40 0.05 0.016 0.002
0.50 0.020 0.80 0.30 0.031 0.012 0.03 0.03 0.001 0.002
0.001 0.05
Applications:
Cursor Control Computer Display Notebook Computer Internet Appliance Palm &Hand Held computer Sub-Notebook Computer Directional Control Stick Applications Video Game Controllers
0.30 0.012 4.96 0.195 1.01 0.040 Below Horizontal
1.80 0.071
Front View
View
Standard Resistance Value: 2.5K Standard Bridge Resistance Tolerance: ±1.0% Standard Resistance Match: ±1.0% Output Linearity: 1.0%
Operating Temperature: -20°C +80°C Maximum Reflow Temperature: 215°C seconds Cycle Life: >8,000,000 cycles Maximum Force: Horizontal Vertical 20Kg Typical Output Characteristics: Axis 0.85µV/V/gram Axis 0.125µV/V/gram
6.00 0.236
Schematic Diagram
NOTES: General Tolerances ±0.127 inch ±0.005 Dimensions mm/in. Overall post heights achieved utilizing Plastic Adaptor Cap. output sensitivity dependent overall post height.
Bottom View
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 109A
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com 109A
Dual Terminator Schematics
Standard Dual Terminator products contain (2N-2) resistors different values with each resistor value connected common buss. assigns resistance value portion standard part numbers dual terminator network different methods.
Dual Terminator Resistor Values Codes
Ohms 4.7K 2.2K 1.5K Thevenin Equivalent Code 150A 190A 290A 330A 340A 400A 500B 670A 590A 500A 780A 670B 810A 600A 650A 730A 710A 750B 720A 600B 750A 990A 960A 101D 101B 111B 131C 121A 111A 101A 171D 131A 121B 111D 101C 171C 131B 171A Ohms 1.1K 1.2K 1.5K 1.5K 2.2K 2.2K 2.2K 3.3K 3.9K 4.7K 6.8K 2.3K 3.3K 2.2K 1.2K 1.5K 3.3K 5.6K 4.4K 3.3K 6.2K 4.7K 3.3K 100K Thevenin Equivalent Code 1031 1000 1579 1467 1320 2022 1200 1939 1788 3873 2500 5194 8361 33,333 111C 880A 191A 221A 181A 131D 171B 241B 231A 241A 321A 281A 311A 251A 351A 361A 401A 381A 571A 771A 671A 731A 601A 751A 102A 102B 162A 152A 132A 202A 122A 192A 182A 392A 252A 522A 842A 333A
Power Derating Curve Resistor Networks
160%
140%
120% Percent Rated Power
100%
Series part number includes actual values resistors dual terminator. example: 770105180/470 R1=180 R2=470
Series 752, 766, part number includes Code value Thevenin equivalent resistances Thevenin equivalent resistance calculated following way: suffix letter relates only sequence variations which equal same equivalent resistance. Reference chart. R1R2 Examples: 766165131A R1=220 R2=330 Req=132 767145191A R1=330 R2=470 Req=194 768205131C R1=180 R2=470 Req=130 common common Series 766, common common Series 752, dual terminator schematics. tolerances ±2%. Other values available request. Suffix letter significance-assigned sequential order.
Degrees Centigrade
Part Marking
following chart indicates characters marked parts with standard marking.
Part 742, 743, 745, 766, 767, Series Pins/Pads Schematic Resistor Value Code Tolerance Date Code YRWK
3-digit 3-digit 3-digit 3-digit 2-digit 2-digit
4-digit 4-digit
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com DTCB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com PDC/PMC
Surface Mount Land Patterns
Concave Convex Chip Resistor Arrays 742-746
Surface Mount Series
Stencil Opening
Solder Paste Stencil Opening
Surface Mount Series
Land Patterns
Dim.
Stencil Opening
Solder Paste Stencil Opening
Land Patterns
Dim.
Concave/Convex
Series Dimensions mm/inch
0.66 0.76 1.52 0.38 0.026 0.030 0.060 0.015 0.051 0.064 1.40 0.30 0.020 0.025 0.055 0.012
Pads
0.125 0.050 0.030 0.050 0.025 0.050
3.18 1.27 0.76 1.27 0.64 1.27
0.51 0.30 1.32 0.15 0.020 0.012 0.052 0.006 0.028 0.030 1.47 0.15 0.011 0.012 0.058 0.006
0.120 0.025 0.017 0.050 0.020 0.035
3.05 0.64 0.43 1.27 0.51 0.89
1.80 0.071 1.90 0.075 3.00 0.118 3.00 0.118 1.52 0.060
0.80 0.032 1.27 0.050 1.27 0.050 1.27 0.050 0.64 0.025
0.50 0.020 0.80 0.032 0.80 0.032 0.80 0.032 0.35 0.014
0.90 0.035 1.20 0.047 1.30 0.051 1.30 0.051 0.80 0.032 Stencil Opening
Solder Paste Stencil Opening
Pads
0.350 0.400 0.450 0.550 0.350 0.400 0.450 0.550
8.89 10.16 11.43 13.97 8.89 10.16 11.43 13.97
Stencil Opening
Solder Paste Stencil Opening
0.175 0.200 0.225 0.275 0.175 0.200 0.225 0.275
4.44 5.08 5.72 6.99 4.44 5.08 5.72 6.99
2.40 0.76 0.38 0.095 0.030 0.015 1.90 0.63 0.33 0.075 0.025 0.013
2.75 0.30 0.15 0.108 0.012 0.006 1.72 0.30 0.15 0.068 0.012 0.006
NOTE: Land Patterns Concave Convex termination same.
Surface Mount Series 766,
Lead Count
Series Land Patterns
DUAL TERMINATION
Series Stencil Openings
Solder Paste Stencil Opening
766-8P 766-14P 766-16P
3.60 0.140 3.60 0.140 3.60 0.140 5.34 0.210 5.34 0.210 5.34 0.210 5.34 0.210 5.34 0.210
5.60 0.220 5.60 0.220 5.60 0.220 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290 7.37 0.290
7.60 0.300 7.60 0.300 7.60 0.300 9.40 0.370 9.40 0.370 9.40 0.370 9.40 0.370 9.40 0.370
3.81 0.150 7.60 0.300 8.90 0.350 7.60 0.300 8.90 0.350 7.60 0.300 8.90 0.350 11.43 0.450
SINGLE TERMINATION
0.63 TYP. 0.025
767-14 767-16
Keep zone stand offs. Circuit board traces should avoided this area allow stand rest directly PCB.
Radius
TYP. 0.050
768-14 768-16
2.03 TYP. 0.080
768-20
Radius
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com SMLPB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com SMLPB
Standard Packaging
Series 752, 753, 766, 767,
Tape Reel Specifications EIA-481-2 Carrier Tape: Cover Tape: Reels: Cover Tape Pull: Slide Pacs: Resistivity X105 ohm/sq. Antistatic .004 max. Molded plastic Antistatic Coding Available coding reel boxes available request. normally uses code configuration accordance with (AIM) symbol specification. Outer container marketing EIA-556.
Series
Tape Reel
Parts/reel Tape width Tape pitch Reel diameter
5000 1000 min. 16mm
2000 1000 min. 16mm
Bulk Pack parts/bag
DIRECTION FEED
PART
PART
PART
PART
PART
Series 742,743,744,745,
Tape Reel 742C043 742C083 742X083 742C163 743C043 743C083 744C043 744C083 745C101 745X101 746X101 745C102 745X102
Series
Bulk Pack Slide Pack Products Parts/Bag Tube Length 457mm/18
Pins Qty/Tube
Parts/Reel Pitch Carrier Width Material Reel diameter
5000 paper
5000 paper
4000 12mm plastic
4000 plastic
4000 12mm plastic
4000 plastic
4000 12mm plastic
4000 12mm plastic
4000 12mm plastic
5000 paper
Series 766/767/768 Series
Tape Reel
PART DATE PART DATE PART DATE PART DATE PART DATE PART DATE
Network Package
12mm 3,000 99ii
16mm 3,000 56ii
16mm 3,000 49ii
767/768 24mm 12mm 2,000
767/768 24mm 12mm 2,000
24mm 12mm 2,000
Bulk Pack parts/bag
Tape Reel
Parts/reel Tape width Tape pitch Reel diameter
5000 1000 min. 24mm
2000 1000 min. 24mm 12mm
Tape width Tape pitch Reel diameter #parts/reel* Reel diameter #parts/reel*
Slide Packs
DATE
PART
DIRECTION FEED
Tube length #parts/slide pac*
48ii
43ii
35ii
DIRECTION FEED
*nominal full reels slide packs
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
Environmental Performance Specifications
Test Max. Mil. Std. Method Test Cond. Test Description Test Max. Mil. Std. Method Test Cond. Test Description
Thermal Cycling Series 752, 753, 766, Series 767, Series 742, 743, 744, 745, Short Time Overload Series 766, Series 752, Series 767, Series 742, Series Series Series Moisture Resistance Series 752, 753, 766, 767, 768, Series 742, 743, 744, 745, Load Humidity Series 752, 753, 766, 767, 768, High Temp Exposure Series 752, 753, 766, 767, 768, Series 742, 743, 744, 745, Load Life Series 752, 753, 766, 767, Series Series 742, 743, 744, 745, Resistance Solder Heat Series 752, 753, 766, 767, Series Series 742, 743, 744, 745, Resistance Leach Series 742, 743, 744, 745, 746, 752, Mechanical Shock Series 752, 753, 766, 767, 768, Vibration Series 752, 753, 766, 768,
0.5% 0.25% 1.0% 0.5% 0.5% 0.25% 2.0% 2.0% 2.0% 2.0% 0.5% 2.0% 1.0%
cycles, -65°C +125°C cycles, -55°C +125°C rated voltage, (100V Max.) rated voltage, (50V Max.) rated voltage, sec. (100V Max.) rated voltage, (100V Max.) rated voltage, sec. (200V Max.) rated voltage, (400V Max.) rated voltage, (50V Max.)
Terminal Strength Series 766, 767, Series Temp Storage Series 752, 753, 766, 768, Temp Operation Series 752, 753, 766, 768, Flammability (UL) Series 752, 753, 766, 768, Non-Fungus MIL-STD 810C Resistance Solvents Solderability
0.25%
pull, sec., bends pull, sec., three bends hours -65°C, load
0.25%
0.25%
-65°C, full load
Series 752, 766, 767, 768, Series Series
94V-0
hours, rated load, -10°C +65°C,
Isopropyl alcohol Flux, 230°C, Seconds dip, coverage
1000 hours, rated load, 70°C, 85-92%
1.0% 1.0% 1.0% 1.0% 0.25% 0.25% 1.0% 0.25%
hours, load, 125°C 1000 hours, load, 125°C 2000 hours 70°C, rated load 1000 hours @70°C, rated load 1000 hours 70°C, rated load seconds 218°C, dwell second dwell 350°C solder second dwell 260°C solder seconds 260°C solder 100g, msec., shocks each plane
0.25%
20g, 10-2000Hz, hours/plane
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com EPSB
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com EPSC
North American Sales Offices
CANADA
ALBERTA
North American Sales Offices
ILLINOIS IOWA MICHIGAN MONTANA
MEXICO
Ciber Electronica, S.A. C.V. Lopez Mateos 1480, Suite Col. Campo Polo Chapalita Guadalajara, Jalisco Mexico 45040 Phone: (52) 3-647-5217/647-1998 Fax: (52) 3-121-3331 E-Mail: cservice@ciber.com.mx Ciber Electronica, S.A. C.V. Interior B-6, Col. Nicolas Garza Nuevo Leon, 66477 Mexico Phone: (52) 8-327-7380 Fax: (52) 8-327-7381
ARKANSAS
CONNECTICUT
Electro Source Inc. 2635-37th Avenue Suite Calgary, Alberta Phone: (403) 735-6230 Fax: (403) 735-0599
BRITISH COLUMBIA
Gold Star Sales Inc. Inca Lane Springs Village, 71909 Phone/Fax: (501) 922-0807 E-mail: rozema@ipa.net
CALIFORNIA
Massachusetts
DELAWARE
Eastern Pennsylvania
FLORIDA
Electro Source Inc. 6830 Burlington Avenue Burnaby, B.C. Phone: (604) 435-2533 Fax: (604) 435-2538
MANITOBA
Northern CAEwing-Foley, Inc. 10495 Bandley Drive Cupertino, 95014-1972 Phone: (408) 342-1220 Fax: (408) 342-1221 E-mail: info@ewingfoley.com Website: www.ewingfoley.com
Ewing-Foley, Inc. Linden Ave. Auburn, 95603 Phone: (530) 885-6591 Fax: (530) 885-6594 E-mail: info@ewingfoley.com Website: www.ewingfoley.com
M-Squared, Inc. 25400 U.S. Suite Clearwater, 33763-2188 Phone: (727) 669-2408 Fax: (727) 669-0431 Website: www.m2i.com M-Squared, Inc. 2431 Aloma Avenue, Suite Winter Park, 32792 Phone: (407) 682-6662 Fax: (407) 682-7038 Website: www.m2i.com M-Squared, Inc. 4945 Avenue Boca Raton, 33431 Phone: (954) 214-6310 Fax: (954) 447-0086 E-mail: sparish@m2i.com Website: www.m2i.com
GEORGIA
Northern ILMax Technical Sales 2121 West Army Trail Road, Suite Addison, 60101 Phone: (630) 953-9722 Fax: (630) 953-9744 E-mail: sales @maxtechsales.com Website: www.maxtechsales.com Southern Missouri
INDIANA
Seltec Sales Corp. Third Ave., S.E., Suite P.O. 2172 Cedar Rapids, 52406 Phone: (319) 364-7660 Fax: (319) 364-7906 E-mail: tomekland@seltecsales.com www.seltecsales.com
KANSAS
Bailey's Electronics Sales Technology, Inc. 22601 Shadow Pine Novi, 48375 Phone: (248) 449-1159 Fax: (248) 449-1163 Bailey's Electronics Sales Technology, Inc. 5321 Huron Hills Drive Commerce Township, 48382 Phone: (248) 363-5384 Fax: (248) 363-5709 Bailey's Electronics Sales Technology, Inc. 3261 Stoneridge Drive Rockford, 49341 Phone: (616) 863-6464 Fax: (616) 863-6465 Bailey's Electronics Sales Technology, Inc. 2711 Ferncliff Royal Oak, 48073 Phone: (248) 288-9380 Fax: (248) 288-9381
MINNESOTA
Washington
NEBRASKA
Advanced Technical Sales, Inc. Collins Cedar Rapids, 52402 Phone: (319) 393-8280 Fax: (319) 393-7258 E-mail: david@techalli.com
NEVADA
Alberta
MARITIME PROVINCES
UNITED STATES
ALABAMA
Ontario
ONTARIO
(Delco/Delphi Only) AlphaTech 1777 East Lincoln Road Kokomo, 46902 Phone: (765) 455-5000 Fax: (765) 455-5010 E-mail: microcom@netusa1.net Bailey's Electronics Sales Technology, Inc. 3208 LaFountain Kokomo, 46902-3712 Phone: (765) 455-0777 Fax: (765) 455-0888 Bailey's Electronics Sales Technology, Inc. 1132 Rangeline Road, Suite Carmel, 46032 Phone: (317) 848-9958 Fax: (317) 848-0952 Bailey's Electronics Sales Technology, Inc. 1725 Ardmore Avenue Fort Wayne, 46802 Phone: (219) 434-0942 Fax: (219) 434-0573
Advanced Technical Sales, Inc. 2012 Prairie Circle, Suite Olathe, 66062 Phone: (913) 782-8702 Fax: (913) 782-8641 E-mail: dduwe@atsks.com Website: www.atsks.com
KENTUCKY
Northern NVSee California- Ewing-Foley, Inc. Southern NVSee California- Westrep
Vegas- Arizona
HAMPSHIRE
Electro Source Inc. Hines Road, Suite Kanata, Ontario Phone: (613) 592-3214 Fax: (613) 592-4256 Electro Source Inc. Galaxy Blvd. Rexdale, Ontario Phone: (416) 675-4490 Fax: (416) 675-6871
QUEBEC
M-Squared, Inc. 4960 Corporate Drive, Suite 115D Huntsville, 35805 Phone: (256) 830-0498 Fax: (256) 837-7049 E-Mail: jvickers@m2i.com Website: www.m2i.com
ALASKA
IndianaBailey's Electronic Sales Tech., Inc., Carmel
LOUISIANA
Massachusetts
JERSEY
Washington
ARIZONA
Southern CAWESTREP 2557 West Woodland Drive Anaheim, 92801 Phone: (714) 527-2822 Fax: (714) 527-3868 Website: www.westrep.com
WESTREP 16885 Bernardo #285 Diego, 92127 Phone: (858) 674-1880 Fax: (858) 674-1878 Website: www.westrep.com
COLORADO
Northern NJSee York-Metro Southern NJSee Eastern Pennsylvania
MEXICO
Texas
MAINE
Massachusetts
MARYLAND
Electro Source Inc. 6600 Trans Canada Hwy. #420 Point Claire, Quebec Phone: (514) 630-7486 Fax: (514) 630-7421
SASKATCHEWAN
Compass Marketing Sales, Inc. 11801 North Tatum Blvd., Suite Phoenix, 85028 Phone: (602) 996-0635 Fax: (602) 996-0586 Website: www.compassaz.com Compass Marketing Sales, Inc. 2410 Ruthrauff Road, Suite Tuscon, 85705 Phone: (520) 292-0222 Fax: (520) 292-1008 Website: www.compassaz.com
M-Squared, Inc. 6465 East Johns Crossing, Suite Duluth, 30097 Phone: (800) 789-7937 Fax: (770) 889-7534 Website: www.m2i.com
HAWAII
Cetan, Inc. 9708 Monroe Street, Suite Cockeysville, 21030 Phone: (410) 666-7300 Fax: (410) 666-1171 E-mail: sales@cetaninc.com
MASSACHUSETTS
Robert Marshall Co., Inc. 3234 Rice Street Paul, 55126-3047 Phone: (651) 287-0011 Fax: (651) 287-0017 E-mail: info@rmarshall.com Website: www.rmarshall.com
MISSISSIPPI
Compass Marketing Sales Inc. 11217 Morocco Albuquerque, 87111 Phone: (505) 296-8878 Fax: (505) 292-1809 Website: www.compassaz.com
YORK-NY METRO
IN-CTS Elcom, Inc. 12200 Briarwood Ave., #175 Englewood, 80112 Phone: (303) 792-3330 Fax: (303) 792-2221 E-mail: Info@elcom-inc.com Website: www.elcom-inc.com
IDAHO
Alabama
MISSOURI
Southern Colorado Northern Washington
Alberta
Selmark Assoc., Inc. Medway Road, Suite Milford, 01757 Phone: (508) 478-9088 Fax: (508) 478-5145 E-mail: salesin@selmark.com Website: www.selmark.com
Advanced Technical Sales, Inc. 13765 Charles Rock Rd., Suite Bridgeton, 63044 Phone: (314) 291-5003 Fax: (314) 291-7958 E-mail: atsstl@aol.com
Neptune Electronics Co., Inc. Oval Drive, Suite Islandia, 11749 Phone: (631) 234-2525 Fax: (631) 234-2707 E-mail: info@neccoelect.com
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
North American Sales Offices
YORK-UPSTATE OREGON TENNESSEE WASHINGTON
International Sales Offices
AFRICA
SOUTH AFRICA FINLAND UNITED KINGDOM JAPAN
Nycom, Inc. Adler Syracuse, 13057 Phone: (315) 437-8343 Fax: (315) 437-1208 E-mail: nycominc@prodigy.net
NORTH CAROLINA
Halco Incorporated 10725 S.W. Barbur Boulevard, Suite Portland, 97219 Phone: (503) 452-7520 Fax: (503) 452-7521
PENNSYLVANIA
Alabama
TEXAS
M-Squared, Inc. 7101 Creedmoor Road, Suite Raleigh, 27613 Phone: (919) 848-4300 Fax: (919) 848-1125 Website: www.m2i.com
NORTH DAKOTA
Eastern PAGSA Sales, Inc. Lakeside Drive Southampton, 18966 Phone: (215) 355-4600 Fax: (215) 245-4817 Western PACentury Technical Sales, Inc. 20120 Route Suite 105-198 Cranberry Township, 16066 Phone: (412) 464-6616 Fax: (412) 464-6617
PUERTO RICO
Gold Star Sales Inc. 2309 Coit Road, Suite Plano, 75075 Phone: (972) 398-6661 Fax: (972) 398-6662 E-mail: info@goldstarsales.com Website: www.goldstarsales.com Gold Star Sales Inc. Ranch Road 620S, PMB#C-7 Austin, 78734 Phone: (800) 824-0486/ (512) 261-3860 Fax: (512) 261-3584 E-mail: info@goldstarsales.com Website: www.goldstarsales.com Gold Star Sales Inc. 19703-B Eastex Freeway, Suite Humble, 77338 Phone: (281) 296-0938 Fax: (281) 296-8758 E-mail: info@goldstarsales.com Website: www.goldstarsales.com
UTAH
Halco 14734 N.E. Street Redmond, 98052 Phone: (425) 497-8500 Fax: (425) 497-8555 E-mail: georgealecci@ halco-sales.com Website: www.halco-sales.com
WEST VIRGINIA
Power Trend (Pty) Ltd. Central Street Houghton, Johannesburg Gauteng 2198 South Africa Phone: (728) 3102 Fax: (728) 6789 E-mail: trend@infonet.co.za
UNLISTED COUNTRIES
Compomill Finland Renbackavagen FIN-02700 Grankulla, Finland Phone: (358) 9-586-44-70
FRANCE
Eastern WVSee Maryland Western WVSee Ohio-Century, Columbus
WISCONSIN
South Africa
Allee chataigniers buisson couldre 78190 Trappes, France Phone: (33) 1-30-62-64-64 Fax: (33) 1-30-62-40-10 E-mail: p2mblgm@iway.fr Website: www.p2m.com
GERMANY
Corporation U.K., Ltd. Blantyre Industrial Estate High Blantyre Glasgow, Scotland, United Kingdom Phone: (44) 1-698-505050 Fax: (44) 1-698-506050
UNLISTED COUNTRIES
Corporation 2-17-2, Midori-Cho, Fuchu-Shi Tokyo 183-0006, Japan Phone: (81) 42-336-5767 Fax: (81) 42-336-5353 E-mail: spg@koanet.co.mp
KOREA
U.K., Ltd.
MIDDLE EAST/ASIA
INDIA
AMERICA-NORTH
Resistor/Electrocomponents Parr Road Berne, 46711 Phone: (219) 589-3111 Fax: (219) 589-3243 E-mail: resistors@rb.ctscorp.com
Minnesota
OHIO
Century Technical Sales, Inc. 8977 Columbia Road, Suite Loveland, 45140 Phone: (513) 677-5088 Fax: (513) 677-1775 E-mail: ctscinci@centsales.com Website: www.centsales.com Century Technial Sales, Inc. 24600 Center Ridge Rd., Suite Westlake, 44145 Phone: (440) 808-9171 Fax: (440) 871-9681 E-mail: ctscleve@centsales.com Website: www.centsales.com Century Technical Sales, Inc. 6161 Busch Blvd., Suite Columbus, 43229 Phone: (614) 433-7500 Fax: (614) 433-9085 E-mail: ctscol@centsales.com Website: www.centsales.com
OKLAHOMA
Electronic Sales Associates Calle #293 Extension Agustin Piedras, P.R. 00926 Phone: (787) 767-6706 Fax: (787) 754-9170 E-mail: esapr@compuserve.com
RHODE ISLAND
Eastern WIMax Technical Sales 2717 Grandview Blvd., Suite Waukesha, 53188 Phone: (262) 513-0494 Fax: (262) 513-0751 E-mail: sales@maxtechsales.com Website: www.maxtechsales.com Western WISee Minnesota
WYOMING
Eurocomp Elektronik GmbH Terrassenstrasse D-61231 Nauheim Phone: (49) 6032-9308-33 Fax: (49) 6032-9308-30
ITALY
Motwane Private Limited 127, Mahatma Gandhi Road P.O. 1312 Fort, Bombay 023, India Phone: (91) 22-2673845 Fax: (91) 22-2626969
Industrial Kwanak Hyundai Apt. 125-902 #1001, Bongchun Dong, Kwanak-Ku, Seoul 151-053 Korea Phone: (822) 874-8844 Fax: (822) 873-3211 E-mail: bansukoh@kornet.net
SINGAPORE
AMERICA-SOUTH
BRAZIL
Massachusetts
SOUTH CAROLINA
North Carolina
SOUTH DAKOTA
Elcom, Inc. 3348 Main Street Salt Lake City, 84115 Phone: (801) 486-7775 Fax: (801) 486-7793 E-mail: info@elcom-inc.com Website: www.elcom-inc.com
VERMONT
Colorado
Ciber Electronica Ipanema-303 Santo Andre Paulo, Brazil 09271-500 Phone: (55-11) 7600-3486 Fax: (55-11) 7600-3486
Fast Elettronica Italiana, S.p.A. Rovetta 20127 Milan, Italy Phone: (39) 0-2-2610141 Fax: (39) 0-2-2822287
SWEDEN
ASIA PACIFIC
AUSTRALIA
EUROPE
AUSTRIA
Compomill Nordic Components Dragonvagen Upplands Vasby, Sweden Phone: (46) 8-594-111-50 Fax: (46) 8-594-211-60 Compomill West Molndalsvagen Gothenburg, Sweden Phone: (46) 31-733-2150 Fax: (46) 31-703-4070
Zatek Australia Pty. Ltd. Arrow Electronics Australia Pty. Ltd. 9-10 Bastow Place Mulgrave Victoria 3170, Australia Phone: (61) 3-9562-1520 Fax: (61) 3-9561-2148 E-mail: robin.aitken@arwnet.com.au
HONG KONG
Electronics Pte. Ltd. 605-B MacPherson Road, #05-10 Citimac Industrial Complex Singapore 1336 Phone: (65) 382-5551 Fax: (65) 382-4282 E-mail: jflel@cyberway.com.sg
TAIWAN
Iowa
Massachusetts
VIRGINIA
Maryland
Perpetual Bauelementeagentur Spitzbergweg A-4800 Attnang-Pucheim, Austria Phone: (43) 7674-62536-0 Fax: (43) 7674-62536-2 E-Mail: office@perpetual.at
DENMARK
Electronics Hong Kong, Ltd. Room 1533 15/F, Metro Centre Phase Hing Street Kowloon Bay, Kowloon Hong Kong Phone: (852) 2-756-5638 Fax: (852) 2-750-7042
Road Electronics Ltd. 18-3 Chien Chung City, Taipei Hsien, Taiwan Republic China Phone: (886) 2-8226-5686 Fax: (886) 2-8226-5687 Website: amroad.com.tw
THAILAND
Texas
Compomill Tagtaekkervej DK-5230 Odense Denmark Phone: (45) 66-15-76-32 Fax: (45) 66-15-76-42 E-mail: compomill@compomill.dk
Platworth Co., Ltd. Floor, Phaholyothin Place Bldg. 408/14, Phaholyothin Road, Sam-Sean Nai, Phayathai, Bangkok 10400, Thailand Phone: (662) 619-1331-3 Fax: (662) 619-1334 E-mail: kaelic@mozart.inet.co.th
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
Resistor/Electrocomponents Parr Road Berne, 46711 fax: (219) 589-3243 www.ctscorp.com
Resistor/Electrocomponents Products Catalog also World Wide www.ctscorp.com. Catalog updated regularly provide customers with latest information products improvements. also contact resistors@rb.ctscorp.com
Around World, Your Single Source Excellence
Other recent searches
WC1602K - WC1602K WC1602K Datasheet
S5S3 - S5S3 S5S3 Datasheet
MMBT6428LT1G - MMBT6428LT1G MMBT6428LT1G Datasheet
MMBT6429LT1G - MMBT6429LT1G MMBT6429LT1G Datasheet
MB2198-01-E - MB2198-01-E MB2198-01-E Datasheet
CRO2925A-LF - CRO2925A-LF CRO2925A-LF Datasheet
AN020903-0808 - AN020903-0808 AN020903-0808 Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
