ORIGINAL FIRST SHEET THIS DRAWING BEEN REPLACED. CURRENT CAGE COD

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

ORIGINAL FIRST SHEET THIS DRAWING BEEN REPLACED. CURRENT CAGE COD

Datasheet Thumbnail

Top Searches for this datasheet

REVISIONS DESCRIPTION Updated drawing reflect MIL-H-38534 processing. Editorial changes throughout. Correct paragraphs 4.3.1.b. Correct table Update drawing boilerplate. DATE (YR-MO-DA) 91-12-10 02-02-13 APPROVED Alan Barone Raymond Monnin
ORIGINAL FIRST SHEET THIS DRAWING BEEN REPLACED.
CURRENT CAGE CODE 67268
SHEET SHEET STATUS SHEETS PMIC SHEET
PREPARED Donald Osborne CHECKED DiCenzo
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS POST OFFICE 3990 COLUMBUS, OHIO 43216-5000
THIS DRAWING AVAILABLE DEPARTMENTS AGENCIES DEPARTMENT DEFENSE AMSC
APPROVED Nelson Hauck
MICROCIRCUIT, HYBRID, LINEAR, WIDE BAND POWER OPERATIONAL AMPLIFIER, THICK FILM
DRAWING APPROVAL DATE 85-10-21 REVISION LEVEL SIZE SHEET CAGE CODE
14933
85089
5962-E358-01
DSCC FORM 2233 DISTRIBUTION STATEMENT Approved public release; distribution unlimited.
SCOPE Scope. This drawing documents product assurance class, class (high reliability) choice case outlines lead finishes available reflected Part Identifying Number (PIN). PIN. shall shown following example: 85089 Drawing number Device type (see 1.2.1) Case outline (see 1.2.2) Lead finish (see 1.2.3)
1.2.1 Device type(s). device type(s) shall identify circuit function follows: Device type Generic number LH0101A, FLH0101AK LH0101, FLH01010K Circuit function Power operational amplifier Power operational amplifier
1.2.2 Case outline(s). case outline(s) shall designated MIL-STD-1835 follows: Outline letter Descriptive designator figure Terminals Package style Metal base flange mount (TO-3)
1.2.3 Lead finish. lead finish shall specified MIL-PRF-38534. Absolute maximum ratings. Supply voltage (±VS). Input voltage range. Power dissipation (PD) Power dissipation (PD) Differential input voltage. Peak output current pulse) Output short circuit duration Storage temperature range Lead temperature (soldering, seconds). Thermal resistance: Junction-to-case (JC) Junction-to-ambient (JA) Junction temperature (TJ) Recommended operating conditions. Ambient operating temperature range (TA). -55°C +125°C Continuous -65°C +150°C +300°C 2°C/W 25°C/W +150°C
+25°C. Derate linearly 25°C/W zero 150°C. +25°C. Derate linearly 2°C/W zero 150°C. +25°C, 0.35. Rating applies long package power dissipation exceeded.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
APPLICABLE DOCUMENTS Government specification, standards, handbooks. following specification, standards, handbooks form part this drawing extent specified herein. Unless otherwise specified, issues these documents those listed issue Department Defense Index Specifications Standards (DoDISS) supplement thereto, cited solicitation. SPECIFICATION DEPARTMENT DEFENSE MIL-PRF-38534 Hybrid Microcircuits, General Specification for. STANDARDS DEPARTMENT DEFENSE MIL-STD-883 Test Method Standard Microcircuits. MIL-STD-1835 Interface Standard Electronic Component Case Outlines. HANDBOOKS DEPARTMENT DEFENSE MIL-HDBK-103 List Standard Microcircuit Drawings. MIL-HDBK-780 Standard Microcircuit Drawings. (Unless otherwise indicated, copies specification, standards, handbooks available from Standardization Document Order Desk, Robbins Avenue, Building Philadelphia, 19111-5094.) Order precedence. event conflict between text this drawing references cited herein, text this drawing takes precedence. Nothing this document, however, supersedes applicable laws regulations unless specific exemption been obtained. REQUIREMENTS Item requirements. individual item performance requirements device class shall accordance with MIL-PRF-38534. Compliance with MIL-PRF-38534 include performance tests herein designated device manufacturer's Quality Management (QM) plan designated applicable device class. Therefore, tests inspections herein performed applicable device class (see MIL-PRF-38534). Furthermore, manufacturers take exceptions alternate methods tests inspections herein perform them. However, performance requirements defined MIL-PRF-38534 shall applicable device class. modification plan shall affect form, fit, function described herein. Design, construction, physical dimensions. design, construction, physical dimensions shall specified MIL-PRF-38534 herein. 3.2.1 Case outline(s). case outline(s) shall accordance with 1.2.2 herein figure 3.2.2 Terminal connections. terminal connections shall specified figure
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
Electrical performance characteristics. Unless otherwise specified herein, electrical performance characteristics specified table shall apply over full specified operating temperature range. Electrical test requirements. electrical test requirements shall subgroups specified table electrical tests each subgroup defined table Marking device(s). Marking device(s) shall accordance with MIL-PRF-38534. device shall marked with listed herein. addition, manufacturer's vendor similar also marked MIL-HDBK-103 QML-38534. Data. addition general performance requirements MIL-PRF-38534, manufacturer device described herein shall maintain electrical test data (variables format) from initial quality conformance inspection group sample, each device type listed herein. Also, data should include summary parameters manually tested, those which, any, guaranteed. This data shall maintained under document revision level control manufacturer made available preparing activity (DSCC-VA) upon request. Certificate compliance. certificate compliance shall required from manufacturer order supply this drawing. certificate compliance (original copy) submitted DSCC-VA shall affirm that manufacturer's product meets performance requirements MIL-PRF-38534 herein. Certificate conformance. certificate conformance required MIL-PRF-38534 shall provided with each microcircuits delivered this drawing. QUALITY ASSURANCE PROVISIONS Sampling inspection. Sampling inspection procedures shall accordance with MIL-PRF-38534 modified device manufacturer's Quality Management (QM) plan. modification plan shall affect form, fit, function described herein. Screening. Screening shall accordance with MIL-PRF-38534. following additional criteria shall apply: Burn-in test, method 1015 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available either DSCC-VA acquiring activity upon request. Also, test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1015 MIL-STD-883. specified accordance with table method 1015 MIL-STD-883.
Interim final electrical test parameters shall specified table herein, except interim electrical parameter tests prior burn-in optional discretion manufacturer.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
TABLE Electrical performance characteristics.
Test
Symbol
Conditions -55°C +125°C unless otherwise specified
Group subgroups
Device type
Limits
Unit
Input offset voltage Input bias current Input offset current Large signal voltage gain AVOL +25°C 100, +25°C +25°C Common mode rejection ratio footnotes table. CMRR +25°C
1000 1000 V/mV
Output voltage swing
±11.7
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
TABLE Electrical performance characteristics Continued.
Test
Symbol
Conditions -55°C +125°C unless otherwise specified
Group subgroups
Device type
Limits
Unit
Power supply rejection ratio PSRR +25°C +25°C +25°C Supply current Slew rate +25°C +25°C +25°C
V/µs
Gain-bandwidth product
Unless otherwise specified,
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
Case outline
Symbol
Millimeters 38.33 39.35 22.35 23.50 19.30 19.69 8.76 10.03 0.92 1.12 2.16 2.66 12.57 12.83 29.90 30.40 14.96 15.22 5.59 7.11 3.89 4.04 24.89 25.91
Inches 1.509 1.549 0.880 0.925 0.760 0.775 0.345 0.395 0.036 0.044 0.085 0.105 0.495 0.505 1.177 1.197 0.589 0.599 0.220 0.280 0.153 0.159 0.980 1.020
NOTES: Leads true position within 0.010 inch (0.25 seating plane. preferred system measurement metric This case outline originally designed using inchpound units measurement, event conflict between metric inch-pound units, inch-pound shall take precedence. numbers reference marked package. FIGURE Case outline(s).
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
Device type Case outline Terminal number Case
Terminal symbol +Current limit (ISC+) Feedback (See note) -VIN +VIN -Current limit (ISC-) Output
NOTE: electrically connected internally. connection should made pin.
FIGURE Terminal connections.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
TABLE Electrical test requirements. MIL-PRF-38534 test requirements Subgroups accordance with MIL-PRF-38534, group test table) -1*,
Interim electrical parameters Final electrical parameters Group test requirements Group end-point electrical parameters applies subgroup
Conformance periodic inspections. Conformance inspection (CI) periodic inspection (PI) shall accordance with MIL-PRF-38534 specified herein. 4.3.1 Group inspection (CI). Group inspection shall accordance with MIL-PRF-38534 follows: Tests shall specified table herein. Subgroups shall omitted.
4.3.2 Group inspection (PI). Group inspection shall accordance with MIL-PRF-38534. 4.3.3 Group inspection (PI). Group inspection shall accordance with MIL-PRF-38534 follows: End-point electrical parameters shall specified table herein. Steady-state life test, method 1005 MIL-STD-883. Test condition test circuit shall maintained manufacturer under document revision level control shall made available either DSCC-VA acquiring activity upon request. Also, test circuit shall specify inputs, outputs, biases, power dissipation, applicable, accordance with intent specified test method 1005 MIL-STD-883. specified accordance with table method 1005 MIL-STD-883. Test duration: 1,000 hours, except permitted method 1005 MIL-STD-883.
4.3.4 Group inspection (PI). Group inspection shall accordance with MIL-PRF-38534. PACKAGING Packaging requirements. requirements packaging shall accordance with MIL-PRF-38534.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
NOTES Intended use. Microcircuits conforming this drawing intended Government microcircuit applications (original equipment), design applications, logistics purposes. Replaceability. Microcircuits covered this drawing will replace same generic device covered contractorprepared specification drawing. Configuration control SMD's. proposed changes existing SMD's will coordinated with users record individual documents. This coordination will accomplished accordance with MIL-STD-973 using Form 1692, Engineering Change Proposal. Record users. Military industrial users shall inform Defense Supply Center Columbus when system application requires configuration control applicable SMD. DSCC will maintain record users this list will used coordination distribution changes drawings. Users drawings covering microelectronic devices (FSC 5962) should contact DSCC-VA, telephone (614) 692-0544. Comments. Comments this drawing should directed DSCC-VA, Post Office 3990, Columbus, Ohio 432165000, telephone (614) 692-0536. Sources supply. Sources supply listed MIL-HDBK-103 QML-38534. vendors listed MIL-HDBK103 QML-38534 have submitted certificate compliance (see herein) DSCC-VA have agreed this drawing.
STANDARD MICROCIRCUIT DRAWING
DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
SIZE
REVISION LEVEL
85089
SHEET
DSCC FORM 2234
STANDARD MICROCIRCUIT DRAWING BULLETIN DATE: 02-02-13 Approved sources supply 85089 listed below immediate acquisition information only shall added MIL-HDBK-103 QML-38534 during next revisions. MIL-HDBK-103 QML-38534 will revised include addition deletion sources. vendors listed below have agreed this drawing certificate compliance been submitted accepted DSCC-VA. This bulletin superseded next dated revisions MIL-HDBK-103 QML-38534.
Standard microcircuit drawing 8508901YA 8508902YA
Vendor CAGE number 27851 27851
Vendor similar FLH0101AK/883 FLH0101K/883
lead finish shown each PIN, representing hermetic package, most readily available from manufacturer listed that part. desired lead finish listed contact Vendor determine availability. Caution. this number item acquisition. Items acquired this number satisfy performance requirements this drawing.
Vendor CAGE number 27851
Vendor name address Film Microelectronics, Incorporated Cedar Hill Street Marlborough, 01752
information contained herein disseminated convenience only Government assumes liability whatsoever inaccuracies information bulletin.

ORIGINAL FIRST SHEET THIS DRAWING BEEN REPLACED. CURRENT CAGE COD

Top Searches for this datasheet

Other recent searches