Product specification IC20 Data Handbook 1996 Product specificati

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Product specification IC20 Data Handbook 1996 Product specificati

Datasheet Thumbnail

Top Searches for this datasheet

80C31/80C51/87C51 CMOS single-chip 8-bit microcontrollers
Product specification IC20 Data Handbook 1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
DESCRIPTION
Philips 80C31/80C51/87C51 high-performance microcontroller fabricated with Philips high-density CMOS technology. CMOS 8XC51 functionally compatible with NMOS 8031/8051 microcontrollers. Philips CMOS technology combines high speed density characteristics HMOS with power attributes CMOS. Philips epitaxial substrate minimizes latch-up sensitivity. 8XC51 contains (80C51) EPROM (87C51), RAM, lines, 16-bit counter/timers, five-source, two-priority level nested interrupt structure, serial port either multi-processor communications, expansion full duplex UART, on-chip oscillator clock circuits. addition, device software selectable modes power reduction-idle mode power-down mode. idle mode freezes while allowing RAM, timers, serial port, interrupt system continue functioning. power-down mode saves contents freezes oscillator, causing other chip functions inoperative.
CONFIGURATIONS
P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 RxD/P3.0 TxD/P3.1 INT0/P3.2 INT1/P3.3 T0/P3.4 CERAMIC PLASTIC DUAL IN-LINE PACKAGE P0.0/AD0 P0.1/AD1 P0.2/AD2 P0.3/AD3 P0.4/AD4 P0.5/AD5 P0.6/AD6 P0.7/AD7 EA/VPP ALE/PROG PSEN P2.7/A15 P2.6/A14 P2.5/A13 P2.4/A12 P2.3/A11 P2.2/A10 P2.1/A9 P2.0/A8
FEATURES
T1/P3.5 WR/P3.6 RD/P3.7 XTAL2 XTAL1
8031/8051 compatible
(80C51) EPROM (87C51) ROMless (80C31) 16-bit counter/timers Full duplex serial channel Boolean processor
Memory addressing capability
CERAMIC PLASTIC LEAD CHIP CARRIER
Power control modes:
Idle mode Power-down mode
CMOS compatible Five speed ranges
12MHz 16MHz 24MHz 33MHz
PLASTIC QUAD FLAT PACK
Five package styles Extended temperature ranges package available
SU00001
PAGE FUNCTIONS.
1996
853-0169 17187
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
CERAMIC PLASTIC LEADED CHIP CARRIER FUNCTIONS
PLASTIC QUAD FLAT PACK FUNCTIONS
PQFP
Function P2.7/A15 PSEN ALE/PROG EA/VPP P0.7/AD7 P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 Function P1.5 P1.6 P1.7 P3.0/RxD P3.1/TxD P3.2/INT0 P3.3/INT1 P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD XTAL2 XTAL1 Function P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14 P2.7/A15 PSEN
Function P0.6/AD6 P0.5/AD5 P0.4/AD4 P0.3/AD3 P0.2/AD2 P0.1/AD1 P0.0/AD0 P1.0 P1.1 P1.2 P.13 P1.4
Function P1.0 P1.1 P1.2 P1.3 P1.4 P1.5 P1.6 P1.7 P3.0/RxD P3.1/TxD P3.2/INT0 P3.3/INT1
Function P3.4/T0 P3.5/T1 P3.6/WR P3.7/RD XTAL2 XTAL1 P2.0/A8 P2.1/A9 P2.2/A10 P2.3/A11 P2.4/A12 P2.5/A13 P2.6/A14
ALE/PROG EA/VPP P0.7/AD7
CONNECT
SU00002
CONNECT
SU00003
LOGIC SYMBOL
XTAL1 PORT ADDRESS DATA
XTAL2
SECONDARY FUNCTIONS
EA/VPP PSEN ALE/PROG INT0 INT1
PORT
PORT
PORT
ADDRESS
SU00004
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ORDERING INFORMATION
PHILIPS NORTH AMERICA EPROM SC87C51CCF40 SC87C51CCK44 SC87C51CCN40 SC87C51CCA44 SC87C51CCB44 SC87C51ACF40 SC87C51ACN40 SC87C51ACA44 SC87C51ACB44 SC87C51CGF40 SC87C51CGK44 SC87C51CGN40 SC87C51CGA44 SC87C51CGB44 SC87C51AGF40 SC87C51AGN40 SC87C51AGA44 SC87C51AGB44
DRAWING NUMBER DRAWING NUMBER
ROMless
TEMPERATURE RANGE PACKAGE1 +70, Ceramic Dual In-line Package, +70, Ceramic Leaded Chip Carrier,
Freq
0590B 1472A
SOT129-1 SOT187-2 SOT307-2
SC80C31BCCN40 SC80C31BCCA44 SC80C31BCCB44
SC80C51BCCN40 SC80C51BCCA44 SC80C51BCCB44
SOT129-1 SOT187-2 SOT307-2
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier, +70, Plastic Quad Flat Pack, +85, Ceramic Dual In-line Package,
0590B
SOT129-1 SOT187-2 SOT307-2
SC80C31BACN40 SC80C31BACA44 SC80C31BACB44
SC80C51BACN40 SC80C51BACA44 SC80C51BACB44
SOT129-1 SOT187-2 SOT307-2
+85, Plastic Dual In-line Package, +85, Plastic Leaded Chip Carrier, +85, Plastic Quad Flat Pack, +70, Ceramic Dual In-line Package, +70, Ceramic Leaded Chip Carrier,
0590B 1472A
SOT129-1 SOT187-2 SOT307-2
SC80C31BCGN40 SC80C31BCGA44 SC80C31BCGB44
SC80C51BCGN40 SC80C51BCGA44 SC80C51BCGB44
SOT129-1 SOT187-2 SOT307-2
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier, +70, Plastic Quad Flat Pack, +85, Ceramic Dual In-line Package,
0590B
SOT129-1 SOT187-2 SOT307-2
SC80C31BAGN40 SC80C31BAGA44 SC80C31BAGB44
SC80C51BAGN40 SC80C51BAGA44 SC80C51BAGB44
SOT129-1 SOT187-2 SOT307-2
+85, Plastic Dual In-line Package, +85, Plastic Leaded Chip Carrier, +85, Plastic Quad Flat Pack,
SC87C51CPF40 SC87C51CPK44 SC87C51CPN40 SC87C51CPA44
0590B 1472A
SOT129-1 SOT187-2
+70, Ceramic Dual In-line Package, +70, Ceramic Leaded Chip Carrier, SC80C31BCPN40 SC80C31BCPA44 SC80C51BCPN40 SC80C51BCPA44
SOT129-1 SOT187-2
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier,
SC87C51APF40 SC87C51APN40 SC87C51APA44
0590B
SOT129-1 SOT187-2
+85, Ceramic Dual In-line Package, SC80C31BAPN40 SC80C31BAPA44 SC80C51BAPN40 SC80C51BAPA44
SOT129-1 SOT187-2
+85, Plastic Dual In-line Package, +85, Plastic Leaded Chip Carrier,
SC87C51CYF40 SC87C51CYK44 SC87C51CYN40 SC87C51CYA44
0590B 1472A
SOT129-1 SOT187-2
+70, Ceramic Dual In-line Package, +70, Ceramic Leaded Chip Carrier, SC80C31BCYN40 SC80C31BCYA44 SC80C51BCYN40 SC80C51BCYA44
SOT129-1 SOT187-2
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier,
Time Programmable EPROM. Erasable EPROM SOT311 replaced SOT307-2.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ORDERING INFORMATION (Continued)
PHILIPS ROMless
(ORDER NUMBER)
ROMless
(MARKING NUMBER)
DRAWING NUMBER
TEMPERATURE RANGE PACKAGE1
Freq
PCB80C31-2 PCB80C31-2
PCB80C31BH2-12P
PCB80C51BH-2P
SOT129-1 SOT187-2 SOT307-22
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier, +70, Plastic Quad Flat Pack,
PCB80C31BH2-12WP PCB80C51BH-2WP PCB80C31BH2-12H PCB80C51BH-2H
PCB80C31-3 PCB80C31-3
PCB80C31BH3-16P
PCB80C51BH-3P
SOT129-1 SOT187-2 SOT307-22
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier, +70, Plastic Quad Flat Pack,
PCB80C31BH3-16WP PCB80C51BH-3WP PCB80C31BH3-16H PCB80C51BH-3H
PCF80C31-3 PCF80C31-3
PCF80C31BH3-16P PCF80C31BH3-16WP PCF80C31BH3-16H PCA80C31BH3-16P
PCF80C51BH-3P PCF80C51BH-3WP PCF80C51BH-3H PCA80C51BH-3P
SOT129-1 SOT187-2 SOT307-22 SOT129-1 SOT187-2
+85, Plastic Dual In-line Package, +85, Plastic Leaded Chip Carrier, +85, Plastic Quad Flat Pack, +125, Plastic Dual In-line Package +125, Plastic Leaded Chip Carrier
PCA80C31BH3-16WP PCA80C51BH-3WP
PCB80C31-4 PCB80C31-4
PCB80C31BH4-24P
PCB80C51BH-4P
SOT129-1 SOT187-2 SOT307-22
+70, Plastic Dual In-line Package, +70, Plastic Leaded Chip Carrier, +70, Plastic Quad Flat Pack,
PCB80C31BH4-24WP PCB80C51BH-4WP PCB80C31BH4-24H PCB80C51BH-4H
PCF80C31-4 PCF80C31-4
PCF80C31BH4-24P PCF80C31BH4-24WP PCF80C31BH4-24H
PCF80C51BH-4P PCF80C51BH-4WP PCF80C51BH-4H
SOT129-1 SOT187-2 SOT307-22
+85, Plastic Dual In-line Package, +85, Plastic Leaded Chip Carrier, +85, Plastic Leaded Chip Carrier,
PCB80C31-5 PCB80C31-5 PCB80C31-5
PCB80C31BH5-30P
PCB80C51BH-5P
SOT129-1 SOT187-2 SOT307-22
+70, Plastic Dual In-line Package +70, Plastic Leaded Chip Carrier +70, Plastic Quad Flat Pack
PCB80C31BH5-30WP PCB80C51BH-5WP PCB80C31BH5-30H PCB80C51BH-5H
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
BLOCK DIAGRAM
P0.0-P0.7 P2.0-P2.7
PORT DRIVERS ADDR REGISTER PORT LATCH
PORT DRIVERS
PORT LATCH
ROM/EPROM
REGISTER
STACK POINTER
TMP2
TMP1
PROGRAM ADDRESS REGISTER
PCON
SCON SBUF
TMOD
TCON
BUFFER
INTERRUPT, SERIAL PORT TIMER BLOCKS
INCREMENTER
PROGRAM COUNTER PSEN ALE/PROG EA/VPP TIMING CONTROL INSTRUCTION REGISTER
DPTR
PORT LATCH
PORT LATCH
OSCILLATOR PORT DRIVERS XTAL1 XTAL2 P1.0-P1.7 PORT DRIVERS
P3.0-P3.7
SU00005
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
DESCRIPTION
MNEMONIC P0.0-0.7 39-32 43-36 37-30 TYPE Ground: reference. Power Supply: This power supply voltage normal, idle, power-down operation. Port Port open-drain, bidirectional port. Port pins that have written them float used high-impedance inputs. Port also multiplexed low-order address data during accesses external program data memory. this application, uses strong internal pull-ups when emitting Port also outputs code bytes during program verification 87C51. External pull-ups required during program verification. Port Port 8-bit bidirectional port with internal pull-ups. Port pins that have written them pulled high internal pull-ups used inputs. inputs, port pins that externally pulled will source current because internal pull-ups. (See Electrical Characteristics: IIL). Port also receives low-order address byte during program memory verification. Port Port 8-bit bidirectional port with internal pull-ups. Port pins that have written them pulled high internal pull-ups used inputs. inputs, port pins that externally being pulled will source current because internal pull-ups. (See Electrical Characteristics: IIL). Port emits high-order address byte during fetches from external program memory during accesses external data memory that 16-bit addresses (MOVX @DPTR). this application, uses strong internal pull-ups when emitting During accesses external data memory that 8-bit addresses (MOV @Ri), port emits contents special function register. Port Port 8-bit bidirectional port with internal pull-ups. Port pins that have written them pulled high internal pull-ups used inputs. inputs, port pins that externally being pulled will source current because pull-ups. (See Electrical Characteristics: IIL). Port also serves special features 80C51 family, listed below: (P3.0): Serial input port (P3.1): Serial output port INT0 (P3.2): External interrupt INT1 (P3.3): External interrupt (P3.4): Timer external input (P3.5): Timer external input (P3.6): External data memory write strobe (P3.7): External data memory read strobe Reset: high this machine cycles while oscillator running, resets device. internal diffused resistor permits power-on reset using only external capacitor VCC. Address Latch Enable/Program Pulse: Output pulse latching byte address during access external memory. normal operation, emitted constant rate oscillator frequency, used external timing clocking. Note that pulse skipped during each access external data memory. This also program pulse input (PROG) during EPROM programming. Program Store Enable: read strobe external program memory. When device executing code from external program memory, PSEN activated twice each machine cycle, except that PSEN activations skipped during each access external data memory. PSEN activated during fetches from internal program memory. External Access Enable/Programming Supply Voltage: must externally held enable device fetch code from external program memory locations 0000H 0FFFH. held high, device executes from internal program memory unless program counter contains address greater than 0FFFH. This also receives 12.75V programming supply voltage (VPP) during EPROM programming. Crystal Input inverting oscillator amplifier input internal clock generator circuits. Crystal Output from inverting oscillator amplifier. NAME FUNCTION
P1.0-P1.7
40-44,
P2.0-P2.7
21-28
24-31
18-25
P3.0-P3.7
10-17
13-19
7-13
ALE/PROG
PSEN
EA/VPP
XTAL1 XTAL2
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
Table
SYMBOL ACC* AUXR# AUXR1# DPTR: IPH# PCON#1 PSW* SADDR# SADEN# SBUF SCON* TCON* T2MOD#
80C52/80C54/80C58 Special Function Registers
DESCRIPTION Accumulator Auxiliary Auxiliary (Note register Data Pointer bytes) Data Pointer High Data Pointer Interrupt Enable Interrupt Priority Interrupt Priority High Port Port Port Port Power Control Program Status Word Slave Address Slave Address Mask Serial Data Buffer Serial Control Stack Pointer Timer Control Timer Mode Control Timer High Timer High Timer Timer DIRECT ADDRESS T2OE DCEN xxxxxx00B
SM0/FE
ADDRESS, SYMBOL, ALTERNATIVE PORT FUNCTION WUPD
RESET VALUE xxxxxxx0B xxxx00x0B
AD14 SMOD0
PT2H AD13
AD12
PT1H AD11 INT1
PX1H AD10 INT0
PT0H T2EX
PX0H xxxxxxxxB 00xx0000B x0000000B x0000000B
AD15 SMOD1
TMOD Timer Mode GATE SFRs addressable. SFRs modified from added 80C51 SFRs. Reserved bits. Reset value depends reset source. Available only SC80C51.
GATE
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
OSCILLATOR CHARACTERISTICS
XTAL1 XTAL2 input output, respectively, inverting amplifier. pins configured on-chip oscillator, shown logic symbol. drive device from external clock source, XTAL1 should driven while XTAL2 left unconnected. There requirements duty cycle external clock signal, because input internal clock circuitry through divide-by-two flip-flop. However, minimum maximum high times specified data sheet must observed.
IDLE MODE
idle mode, puts itself sleep while on-chip peripherals stay active. instruction invoke idle mode last instruction executed normal operating mode before idle mode activated. contents, on-chip RAM, special function registers remain intact during this mode. idle mode terminated either enabled interrupt which time process picked interrupt service routine continued), hardware reset which starts processor same manner power-on reset.
RESET
reset accomplished holding high least machine cycles oscillator periods), while oscillator running. insure good power-up reset, must high long enough allow oscillator time start (normally milliseconds) plus machine cycles.
POWER-DOWN MODE
power-down mode, oscillator stopped instruction invoke power-down last instruction executed. Only contents on-chip preserved. hardware reset only terminate power-down mode. control bits reduced power modes special function register PCON. Table shows state ports during current operating modes.
Table External Status During Idle Power-Down Modes
MODE Idle Idle Power-down Power-down PROGRAM MEMORY Internal External Internal External PSEN PORT Data Float Data Float PORT Data Data Data Data PORT Data Address Data Data PORT Data Data Data Data
CODE SUBMISSION
When submitting code 80C51, following must specified: byte user data byte encryption (SC80C51 only) security bits (SC80C51 only). ADDRESS 0000H 0FFFH 1000H 101FH 1020H 1020H CONTENT DATA BIT(S) COMMENT User Data Encryption Security Security
Security When programmed, this effects masked parts: External MOVC disabled, latched Reset. Security When programmed, this inhibits Verify User ROM.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
Electrical Deviations from Commercial Specifications Extended Temperature Range (87C51) parameters included here same commercial temperature range table.
ELECTRICAL CHARACTERISTICS
Tamb -40°C +85°C, ±10%, (Philips North America SC87C51); SC87C51 (33MHz only), Tamb +70°C, Tamb -40°C +85°C, ±10%, (PCB80C31/51 PCF80C31/51 Philips Parts Only) TEST SYMBOL VIL1 VIH1 PARAMETER Input voltage, except (Philips North America) Input voltage, except (Philips) Input voltage Input high voltage, except XTAL1, Input high voltage XTAL1, Logical input current, ports Logical 1-to-0 transition current, ports Power supply current: Active mode1 16MHz (Philips PCB80C31/51, PCF80C31/51) Active mode 12MHz (Philips North America SC87C51) Idle mode2 16MHz (Philips PCB80C31/51, PCF80C31/51) Idle mode 12MHz (Philips North America SC87C51) Power-down mode3 (Philips PCB80C31/51, PCF80C31/51) Power-down mode (Philips North America SC87C51) 0.45V 2.0V 4.5-5.5V CONDITIONS -0.5 -0.5 -0.5 0.2VCC+1 0.7VCC+0.1 LIMITS 0.2VCC-0.15 0.2VCC-0.25 0.2VCC-0.45 VCC+0.5 VCC+0.5 -750 UNIT
NOTES: operating supply current measured with output pins disconnected; XTAL1 driven with 10ns; 0.5V; 0.5V; XTAL2 connected; Port VCC. idle mode supply current measured with output pins disconnected; XTAL1 driven with 10ns; 0.5V; 0.5V; XTAL2 connected; Port VCC; VSS. power-down current measured with output pins disconnected, XTAL2 connected, Port VCC; VSS.
ABSOLUTE MAXIMUM RATINGS1,
PARAMETER Operating temperature under bias Storage temperature range Voltage EA/VPP Voltage other Maximum Power dissipation (based package heat transfer limitations, device power consumption) RATING +150 +13.0 -0.5 +6.5 UNIT
NOTES: Stresses above those listed under Absolute Maximum Ratings cause permanent damage device. This stress rating only functional operation device these conditions other than those described Electrical Characteristics section this specification implied. This product includes circuitry specifically designed protection internal devices from damaging effects excessive static charge. Nonetheless, suggested that conventional precautions taken avoid applying greater than rated maxima. Parameters valid over operating temperature range unless otherwise specified. voltages with respect unless otherwise noted.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
Tamb +70°C -40°C +85°C, ±20%, (PCB80C31/51 PCF80C31/51) (12, 24MHz versions) Tamb +70°C -40°C +85°C, ±10%, (87C51 24MHz versions) (PCB80C31/51 33MHz version); SC87C51 (33MHz only) Tamb +70°C, TEST SYMBOL VIL1 VIH1 VOL1 PARAMETER Input voltage, except Input voltage CONDITIONS -0.5 0.2VCC+0.9 0.7VCC PSEN3 1.6mA2 3.2mA2 -60µA, -25µA -10µA -800µA, -300µA -80µA 0.45V note note 11.5 0.75VCC 0.9VCC 0.75VCC 0.9VCC -650 LIMITS TYPICAL1 0.2VCC-0.1 0.2VCC-0.3 VCC+0.5 VCC+0.5 0.45 0.45 UNIT
ELECTRICAL CHARACTERISTICS
Input high voltage, except XTAL1, RST7 Input high voltage, XTAL1, RST7
Output voltage, ports
Output voltage, port ALE, PSEN11 Output high voltage, ports ALE,
VOH1
Output high voltage (port external mode)
Logical input current, ports Logical 1-to-0 transition current, ports Input leakage current, port Power supply Active mode 12MHz8 (Philips) Active mode 12MHz5 (Philips North America) Idle mode 12MHz9 (Philips) Idle mode 12MHz (Philips North America) Power-down mode10 (Philips Philips North America) Internal reset pull-down resistor (Philips North America) (Philips) current:7
RRST
capacitance12 NOTES: Typical ratings guaranteed. values listed room temperature, Capacitive loading ports cause spurious noise superimposed VOLs ports noise external capacitance discharging into port port pins when these pins make 1-to-0 transitions during operations. worst cases (capacitive loading 100pF), noise pulse exceed 0.8V. such cases, desirable qualify with Schmitt Trigger, address latch with Schmitt Trigger STROBE input. exceed these conditions provided that single output sinks more than more than outputs exceed test conditions. Capacitive loading ports cause PSEN momentarily fall below 0.9VCC specification when address bits stabilizing. Pins ports source transition current when they being externally driven from transition current reaches maximum value when approximately ICCMAX other frequencies (for Philips North America parts) given Active mode: ICCMAX 1.43 FREQ 1.90; Idle mode: ICCMAX 0.14 FREQ +2.31, where FREQ external oscillator frequency MHz. ICCMAX given Figure Figures through test conditions. Philips North America parts when Tamb -40°C +85°C Philips parts when Tamb -40°C +125°C, Electrical Characteristics table previous page. operating supply current measured with output pins disconnected; XTAL1 driven with 10ns; 0.5V; 0.5V; XTAL2 connected; Port VCC. idle mode supply current measured with output pins disconnected; XTAL1 driven with 10ns; 0.5V; 0.5V; XTAL2 connected; Port VCC; VSS. power-down current measured with output pins disconnected, XTAL2 connected, Port VCC; VSS. Under steady state (non-transient) conditions, must externally limited follows: 15mA Maximum port pin: 26mA Maximum 8-bit port: 67mA Maximum total outputs: exceeds test condition, exceed related specification. Pins guaranteed sink current greater than listed test conditions. capacitance ceramic package 15pF maximum.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ELECTRICAL CHARACTERISTICS PHILIPS NORTH AMERICA DEVICES (SC80C31 SC80C51)
Tamb +70°C -40°C +85°C, ±10%; SYMBOL VIH1 VOL1 VOH1 Input voltage Input high voltage (ports Input high voltage, XTAL1, Output voltage, ports Output voltage, port ALE, PSEN8, Output high voltage, ports Output high voltage (port external mode), ALE9, PSEN3 Logical input current, ports Logical 1-to-0 transition current, ports Input leakage current, port Power supply current (see Figure Active mode 16MHz5 Idle mode 16MHz5 Power-down mode Internal reset pull-down resistor capacitance10 (except 4.5V 1.6mA2 4.5V 3.2mA2 4.5V -30µA 4.5V -3.2mA 0.4V 2.0V note 0.45 note Tamb +70°C Tamb +85°C 11.5 -650 PARAMETER TEST CONDITIONS 4.5V 5.5V LIMITS -0.5 0.2VCC+0.9 0.7VCC TYP1 UNIT 0.2VCC-0.1 VCC+0.5 VCC+0.5
RRST
NOTES: Typical ratings guaranteed. values listed room temperature, Capacitive loading ports cause spurious noise superimposed VOLs ports noise external capacitance discharging into port port pins when these pins make 1-to-0 transitions during operations. worst cases (capacitive loading 100pF), noise pulse exceed 0.8V. such cases, desirable qualify with Schmitt Trigger, address latch with Schmitt Trigger STROBE input. exceed these conditions provided that single output sinks more than more than outputs exceed test conditions. Capacitive loading ports cause PSEN momentarily fall below (VCC-0.7) specification when address bits stabilizing. Pins ports source transition current when they being externally driven from transition current reaches maximum value when approximately Figures through test conditions. Active Mode: FREQ 8.0; Idle Mode: 0.14 FREQ +2.31; Figure This value applies Tamb +70°C. Tamb -40°C +85°C, -750µA. Load capacitance port ALE, PSEN 100pF, load capacitance other outputs 80pF. Under steady state (non-transient) conditions, must externally limited follows: 15mA (*NOTE: This 85°C specification.) Maximum port pin: Maximum 8-bit port: 26mA 71mA Maximum total outputs: exceeds test condition, exceed related specification. Pins guaranteed sink current greater than listed test conditions. tested VOH1, except when then voltage specification. capacitance characterized tested. capacitance less than 25pF. capacitance ceramic package less than 15pF (except 25pF).
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
Tamb +70°C -40°C +85°C, ±10%, (SC87C51 24MHz versions); SC87C51 (33MHz only) Tamb +70°C,
ELECTRICAL CHARACTERISTICS SC87C51 12-33MHz PHILIPS NORTH AMERICA DEVICES
VARIABLE CLOCK3 SYMBOL 1/tCLCL FIGURE Oscillator frequency: SC87C51 PARAMETER Speed Versions 2tCLCL-40 tCLCL-13 tCLCL-20 4tCLCL-65 tCLCL-13 3tCLCL-20 3tCLCL-45 tCLCL-10 5tCLCL-55 UNIT
tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ tAVIV tPLAZ Data Memory tRLRH tWLWH tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tQVWX tWHQX tRLAZ tWHLH External Clock tCHCX tCLCX tCLCH tCHCL
pulse width Address valid Address hold after valid instruction PSEN PSEN pulse width PSEN valid instruction Input instruction hold after PSEN Input instruction float after PSEN Address valid instruction PSEN address float
pulse width pulse width valid data Data hold after Data float after valid data Address valid data Address valid Data valid transition Data hold after address float high high
6tCLCL-100 6tCLCL-100 5tCLCL-90 2tCLCL-28 8tCLCL-150 9tCLCL-165 3tCLCL-50 4tCLCL-75 tCLCL-20 tCLCL-20 tCLCL-20 tCLCL+25 3tCLCL+50
High time time Rise time Fall time
NOTES: Parameters valid over operating temperature range unless otherwise specified. Load capacitance port ALE, PSEN 100pF, load capacitance other outputs 80pF. Philips North America speed versions only. Interfacing 87C51 devices with float times 50ns permitted. This limited contention will cause damage port drivers.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ELECTRICAL CHARACTERISTICS PHILIPS DEVICES
Tamb +70°C, ±20%, (PCB80C31/51, PCF80C31/51)1, VARIABLE CLOCK3 SYMBOL 1/tCLCL FIGURE PARAMETER Oscillator frequency: Speed Versions PCB8031/51 PCA/PCB/PCF80C31/51 PCB/PCF80C31/51 PCB/FB80C31/51 pulse width Address valid Address hold after valid instruction PSEN PSEN pulse width PSEN valid instruction Input instruction hold after PSEN Input instruction float after PSEN Address valid instruction PSEN address float tCLCL-25 5tCLCL-80 tCLCL-25 3tCLCL-45 3tCLCL-60 2tCLCL-40 tCLCL-25 tCLCL-25 4tCLCL-65 UNIT
tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ tAVIV tPLAZ Data Memory tRLRH tWLWH tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tQVWX tWHQX tRLAZ tWHLH External Clock tCHCX tCLCX tCLCH tCHCL
pulse width pulse width valid data Data hold after Data float after valid data Address valid data Address valid Data valid transition Data hold after address float high high
6tCLCL-100 6tCLCL-100 5tCLCL-90 2tCLCL-28 8tCLCL-150 9tCLCL-165 3tCLCL-50 4tCLCL-75 tCLCL-30 tCLCL-25 tCLCL-25 tCLCL+25 3tCLCL+50
High time time Rise time Fall time
NOTES: Parameters valid over operating temperature range unless otherwise specified. Load capacitance port ALE, PSEN 100pF, load capacitance other outputs 80pF. Philips speed versions only. Interfacing 80C31/51 devices with float times 30ns permitted. This limited contention will cause damage port drivers. ±10% 33MHz.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ELECTRICAL CHARACTERISTICS PHILIPS NORTH AMERICA DEVICES (SC80C31 SC80C51)
Tamb +70°C -40°C +85°C, ±10%, 0V1, SYMBOL 1/tCLCL tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ tAVIV tPLAZ Data Memory tRLRH tWLWH tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tQVWX tWHQX tQVWH tRLAZ tWHLH External Clock tCHCX tCLCX tCLCH tCHCL Shift Register tXLXL tQVXH tXHQX tXHDX Serial port clock cycle time Output data setup clock rising edge Output data hold after clock rising edge Input data hold after clock rising edge 12tCLCL 10tCLCL-133 2tCLCL-117 High time time Rise time Fall time tCLCL-tCLCX tCLCL-tCHCX pulse width pulse width valid data Data hold after Data float after valid data Address valid data Address valid Data valid transition Data hold after Data valid high address float high high tCLCL-40 3tCLCL-50 4tCLCL-130 tCLCL-50 tCLCL-50 7tCLCL-150 tCLCL+40 2tCLCL-60 8tCLCL-150 9tCLCL-165 3tCLCL+50 6tCLCL-100 6tCLCL-100 5tCLCL-165 FIGURE PARAMETER Oscillator frequency Speed versions pulse width Address valid Address hold after valid instruction PSEN PSEN pulse width PSEN valid instruction tCLCL-25 5tCLCL-105 tCLCL-30 3tCLCL-45 3tCLCL-105 16MHz CLOCK VARIABLE CLOCK 2tCLCL-40 tCLCL-40 tCLCL-30 4tCLCL-100 UNIT
Input instruction hold after PSEN Input instruction float after PSEN Address valid instruction PSEN address float
tXHDV Clock rising edge input data valid 10tCLCL-133 NOTES: Parameters valid over operating temperature range unless otherwise specified. Load capacitance port ALE, PSEN 100pF, load capacitance other outputs 80pF. Interfacing 80C31/51 devices with float times 45ns permitted. This limited contention will cause damage Port drivers. application note AN457 external memory interfacing.
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
ELECTRICAL CHARACTERISTICS PHILIPS NORTH AMERICA DEVICES (SC80C31 SC80C51)
Tamb +70°C -40°C +85°C, ±10%, 0V1, SYMBOL 1/tCLCL FIGURE PARAMETER Oscillator frequency Speed versions (24MHz) (33MHz) pulse width Address valid Address hold after valid instruction PSEN PSEN pulse width PSEN valid instruction Input instruction hold after PSEN Input instruction float after PSEN Address valid instruction PSEN address float pulse width pulse width valid data Data hold after Data float after valid data Address valid data Address valid Data valid transition Data hold after Data valid high address float high high High time time Rise time Fall time Serial port clock cycle time Output data setup clock rising edge Output data hold after clock rising edge Input data hold after clock rising edge 12tCLCL 10tCLCL-133 2tCLCL-80 tCLCL-25 3tCLCL-50 4tCLCL-75 tCLCL-30 tCLCL-25 7tCLCL-130 tCLCL+25 tCLCL-tCLCX tCLCL-tCHCX 2tCLCL-28 8tCLCL-150 9tCLCL-165 3tCLCL+50 6tCLCL-100 6tCLCL-100 5tCLCL-90 tCLCL-25 5tCLCL-80 24MHz CLOCK tCLCL-25 3tCLCL-45 3tCLCL-60 2tCLCL-40 tCLCL-25 tCLCL-25 4tCLCL-65 VARIABLE CLOCK4 33MHz CLOCK UNIT
tLHLL tAVLL tLLAX tLLIV tLLPL tPLPH tPLIV tPXIX tPXIZ tAVIV tPLAZ Data Memory tRLRH tWLWH tRLDV tRHDX tRHDZ tLLDV tAVDV tLLWL tAVWL tQVWX tWHQX tQVWH tRLAZ tWHLH tCHCX tCLCX tCLCH tCHCL Shift Register tXLXL tQVXH tXHQX tXHDX
External Clock
tXHDV Clock rising edge input data valid 10tCLCL-133 NOTES: Parameters valid over operating temperature range unless otherwise specified. Load capacitance port ALE, PSEN 100pF, load capacitance other outputs 80pF. Interfacing SC80C31/51 devices with float times 45ns permitted. This limited contention will cause damage Port drivers. Variable clock specified oscillator frequencies greater than 16MHz 33MHz. frequencies equal less than 16MHz, 16MHz Electrial Characteristics", page 1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
EXPLANATION SYMBOLS
Each timing symbol five characters. first character always time). other characters, depending their positions, indicate name signal logical status that signal. designations are: Address Clock Input data Logic level high Instruction (program memory contents) Logic level low, PSEN Output data signal Time Valid signal longer valid logic level Float Examples: tAVLL Time address valid low. tLLPL= Time PSEN low.
tLHLL
tAVLL
tLLPL
PSEN
tPLPH tLLIV tPLIV tPLAZ tPXIX
INSTR
tLLAX
tPXIZ
PORT
A0-A7
A0-A7
tAVIV
PORT A0-A15 A8-A15
SU00006
Figure External Program Memory Read Cycle
tWHLH
PSEN
tLLDV tLLWL
tRLRH
tAVLL
PORT
tLLAX tRLAZ
A0-A7 FROM
tRLDV tRHDX
DATA
tRHDZ
A0-A7 FROM
INSTR
tAVWL tAVDV
PORT P2.0-P2.7 A8-A15 FROM A0-A15 FROM
SU00007
Figure External Data Memory Read Cycle
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
tWHLH
PSEN
tLLWL
tWLWH
tAVLL
PORT
tLLAX
tQVWX
tWHQX
A0-A7 FROM
DATA
A0-A7 FROM
INSTR
tAVWL
PORT P2.0-P2.7 A8-A15 FROM A0-A15 FROM
SU00008
Figure External Data Memory Write Cycle
INSTRUCTION
tXLXL
CLOCK
tQVXH
OUTPUT DATA WRITE SBUF
tXHQX
tXHDV
INPUT DATA VALID CLEAR VALID
tXHDX
VALID VALID VALID VALID VALID VALID
SU00027
Figure Shift Register Mode Timing
VCC-0.5 0.45V
0.7VCC 0.2VCC-0.1
tCHCL
tCLCX tCLCL
tCHCX tCLCH
SU00009
Figure External Clock Drive
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
VCC-0.5
0.2VCC+0.9 0.2VCC-0.1
0.45V
NOTE: inputs during testing driven -0.5 logic 0.45V logic `0'. Timing measurements made logic logic `0'.
SU00010
Figure Testing Input/Output
VLOAD+0.1V VLOAD VLOAD-0.1V
TIMING REFERENCE POINTS
VOH-0.1V VOL+0.1V
NOTE: timing purposes, port longer floating when 100mV change from load voltage occurs, begins float when 100mV change from loaded VOH/VOL level occurs. IOH/IOL ±20mA.
SU00011
Figure Float Waveform
ACTIVE MODE (ICCMAX 1.43 freq 1.9)
ACTIVE MODE
IDLE MODE IDLE MODE
4MHz
8MHz
12MHz
16MHz
20MHz
24MHz
30MHz
33MHz
FREQ XTAL1
SU00012
Figure FREQ Valid only within frequency specifications device under test
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
(NC) CLOCK SIGNAL XTAL2 XTAL1 (NC) CLOCK SIGNAL XTAL2 XTAL1
SU00719
SU00720
Figure Test Condition, Active Mode other pins disconnected
Figure Test Condition, Idle Mode other pins disconnected
VCC-0.5 0.45V
0.7VCC 0.2VCC-0.1
tCHCL
tCLCX tCLCL
tCHCX tCLCH
SU00015
Figure Clock Signal Waveform Tests Active Idle Modes tCLCH tCHCL
(NC) XTAL2 XTAL1
SU00016
Figure Test Condition, Power Down Mode other pins disconnected. 5.5V
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
EPROM CHARACTERISTICS
87C51 programmed using modified Quick-Pulse Programmingalgorithm. differs from older methods value used (programming supply voltage) width number ALE/PROG pulses. 87C51 contains signature bytes that read used EPROM programming system identify device. signature bytes identify device 87C51 manufactured Philips Corporation. Table shows logic levels reading signature bytes, programming program memory, encryption table, security bits. circuit configuration waveforms quick-pulse programming shown Figures Figure shows circuit configuration normal program memory verification.
Program Verification
security been programmed, on-chip program memory read program verification. address program memory locations read applied ports shown Figure other pins held `Verify Code Data' levels indicated Table contents address location will emitted port External pull-ups required port this operation. encryption table been programmed, data presented port will exclusive program byte with encryption bytes. user will have know encryption table contents order correctly decode verification data. encryption table itself cannot read out. Reading Signature Bytes signature bytes read same procedure normal verification locations 030H 031H, except that P3.6 P3.7 need pulled logic low. values are: (030H) indicates manufactured Philips (031H) indicates 87C51
Quick-Pulse Programming
setup microcontroller quick-pulse programming shown Figure Note that 87C51 running with 6MHz oscillator. reason oscillator needs running that device executing internal address program data transfers. address EPROM location programmed applied ports shown Figure code byte programmed into that location applied port RST, PSEN pins ports specified Table held `Program Code Data' levels indicated Table ALE/PROG pulsed times shown Figure program encryption table, repeat pulse programming sequence addresses through 1FH, using `Pgm Encryption Table' levels. forget that after encryption table programmed, verification cycles will produce only encrypted data. program security bits, repeat pulse programming sequence using `Pgm Security Bit' levels. After security programmed, further programming code memory encryption table disabled. However, other security still programmed. Note that EA/VPP must allowed above maximum specified level amount time. Even narrow glitch above that voltage cause permanent damage device. source should well regulated free glitches overshoot.
Program/Verify Algorithms
algorithm agreement with conditions listed Table which satisfies timing specifications, suitable.
Erasure Characteristics
Erasure EPROM begins occur when chip exposed light with wavelengths shorter than approximately 4,000 angstroms. Since sunlight fluorescent lighting have wavelengths this range, exposure these light sources over extended time (about week sunlight, years room level fluorescent lighting) could cause inadvertent erasure. this secondary effects, recommended that opaque label placed over window. elevated temperature environments where solvents being used, apply Kapton tape Fluorglas part number 2345-5, equivalent. recommended erasure procedure exposure ultraviolet light 2537 angstroms) integrated dose least 15W-sec/cm2. Exposing EPROM ultraviolet lamp 12,000µW/cm2 rating minutes, distance about inch, should sufficient. Erasure leaves array state.
Table EPROM Programming Modes
MODE Read signature Program code data Verify code data encryption table security PSEN ALE/PROG EA/VPP P2.7 P2.6 P3.7 P3.6
security NOTES: Valid that pin, valid high that pin. 12.75V +0.25V. 5V±10% during programming verification. *ALE/PROG receives programming pulses while held 12.75V. Each programming pulse 100µs (±10µs) high minimum 10µs.
TMTrademark phrase Intel Corporation. 1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
A0-A7 P3.6 P3.7 XTAL2 4-6MHz XTAL1 87C51 DATA +12.75V 100µs PULSES GROUND A8-A11
EA/VPP ALE/PROG PSEN P2.7 P2.6 P2.0-P2.3
SU00017
Figure Programming Configuration
ALE/PROG:
PULSES
ALE/PROG:
10µs
100µs+10
SU00018
Figure PROG Waveform
A0-A7 P3.6 P3.7 XTAL2 4-6MHz XTAL1 87C51 DATA ENABLE A8-A11
EA/VPP ALE/PROG PSEN P2.7 P2.6 P2.0-P2.3
SU00019
Figure Program Verification
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
EPROM PROGRAMMING VERIFICATION CHARACTERISTICS
Tamb 21°C +27°C, 5V±10%, (See Figure SYMBOL 1/tCLCL tAVGL tGHAX tDVGL tGHDX tEHSH tSHGL tGHSL tGLGH tAVQV tELQZ tEHQZ tGHGL PARAMETER Programming supply voltage Programming supply current Oscillator frequency Address setup PROG Address hold after PROG Data setup PROG Data hold after PROG P2.7 (ENABLE) high setup PROG hold after PROG PROG width Address data valid ENABLE data valid Data float after ENABLE PROG high PROG 48tCLCL 48tCLCL 48tCLCL 48tCLCL 48tCLCL 48tCLCL 48tCLCL 48tCLCL 12.5 13.0 UNIT
PROGRAMMING* P1.0-P1.7 P2.0-P2.4 ADDRESS
VERIFICATION* ADDRESS
tAVQV
PORT DATA DATA
tDVGL tAVGL
ALE/PROG
tGHDX tGHAX
tGLGH tSHGL
tGHGL tGHSL
LOGIC EA/VPP LOGIC
LOGIC
tEHSH
P2.7 ENABLE
tELQV
tEHQZ
SU00020
NOTE:
PROGRAMMING VERIFICATION FIGURE VERIFICATION CONDITIONS FIGURE
Figure EPROM Programming Verification
1996
0590B
1996
NOTE 0.098 (2.49) 0.040 (1.02)
CMOS single-chip 8-bit microcontrollers
853-0590B 06688
0.098 (2.49) 0.040 (1.02)
NOTES: Controlling dimension: Inches. Millimeters shown parentheses. Dimension tolerancing ANSI Y14. 5M-1982. "T", "D", reference datums body include allowance glass overrun meniscus seal line, base mismatch. These dimensions measured with leads constrained perpendicular plane numbers start with continue counterclockwise when viewed from top. Denotes window location EPROM products.
0.598 (15.19) 0.571 (14.50)
2.087 (53.01) 2.038 (51.77)
0.100 (2.54)
40-PIN (600 mils wide) CERAMIC DUAL IN-LINE PACKAGE (WITH WINDOW (FA) PACKAGE)
0.225 (5.72) MAX. 0.175 (4.45) 0.145 (3.68) 0.165 (4.19) 0.125 (3.18) 0.055 (1.40) 0.020 (0.51) 0.010 (0.254) 0.015 (0.38) 0.010 (0.25)
0.070 (1.78) 0.050 (1.27)
0.620 (15.75) 0.590 (14.99) (NOTE
SEATING PLANE
0.600 (15.24) (NOTE 0.695 (17.65) 0.600 (15.24)
0.023 (0.58) 0.015 (0.38)
80C31/80C51/87C51
Product specification
1472A
1996
3.05 (0.120) 2.29 (0.090) 0.38 (0.015)
CMOS single-chip 8-bit microcontrollers
853-1472A 05854
1.02 (0.040) CHAMFER
17.65 (0.695) 17.40 (0.685) 16.89 (0.665) 16.00 (0.630)
NOTES: dimensions tolerances conform ANSI Y14.5-1982. window optional. Dimensions include glass protrusion. Glass protrusion 0.005 inches maximum each side. Controlling dimension millimeters. dimensions tolerances include lead trim offset lead plating finish. Backside solder relief optional dimensions reference only.
0.51 (0.02) 17.65 (0.695) 17.40 (0.685) 16.89 (0.665) 16.00 (0.630)
44-PIN CERQUAD J-BEND PACKAGE
0.63 (0.025) MIN.
4.83 (0.190) 3.94 (0.155)
SEATING PLANE
0.73 0.08 (0.029 0.003) 1.27 (0.050) TYP. 0.25 (0.010) MIN. 1.52 (0.060) REF. TYP. PLACES 0.15 (0.006) MIN.
1.02 0.25 (0.040 0.010) DETAIL 0.482 (0.019 0.002) SEATING PLANE BASE PLANE
17.65 (0.656) 17.40 (0.685)
1.27 (0.050)
0.076 (0.003) MIN.
4.83 (0.190) 3.94 (0.155)
SEATING PLANE
DETAIL
12.7 (0.500) NOMINAL
0.25 (0.010) 0.15 (0.006)
0.508 (0.020) MIN.
80C31/80C51/87C51
8.13 (0.320) 7.37 (0.290)
8.13 (0.320) 7.37 (0.290)
DETAIL TYP. SIDES mm/(inch)
DETAIL mm/(inch)
Product specification
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
DIP40: plastic dual in-line package; leads (600 mil)
SOT129-1
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
PLCC44: plastic leaded chip carrier; leads
SOT187-2
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
QFP44: plastic quad flat package; leads (lead length mm); body 1.75
SOT307-2
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
NOTES
1996
Product specification
CMOS single-chip 8-bit microcontrollers
80C31/80C51/87C51
DEFINITIONS
Data Sheet Identification
Objective Specification
Product Status
Formative Design
Definition
This data sheet contains design target goal specifications product development. Specifications change manner without notice. This data sheet contains preliminary data, supplementary data will published later date. Philips Semiconductors reserves right make changes time without notice order improve design supply best possible product. This data sheet contains Final Specifications. Philips Semiconductors reserves right make changes time without notice, order improve design supply best possible product.
Preliminary Specification
Preproduction Product
Product Specification
Full Production
Philips Semiconductors Philips Electronics North America Corporation reserve right make changes, without notice, products, including circuits, standard cells, and/or software, described contained herein order improve design and/or performance. Philips Semiconductors assumes responsibility liability these products, conveys license title under patent, copyright, mask work right these products, makes representations warranties that these products free from patent, copyright, mask work right infringement, unless otherwise specified. Applications that described herein these products illustrative purposes only. Philips Semiconductors makes representation warranty that such applications will suitable specified without further testing modification. LIFE SUPPORT APPLICATIONS Philips Semiconductors Philips Electronics North America Corporation Products designed life support appliances, devices, systems where malfunction Philips Semiconductors Philips Electronics North America Corporation Product reasonably expected result personal injury. Philips Semiconductors Philips Electronics North America Corporation customers using selling Philips Semiconductors Philips Electronics North America Corporation Products such applications their risk agree fully indemnify Philips Semiconductors Philips Electronics North America Corporation damages resulting from such improper sale. Philips Semiconductors East Arques Avenue P.O. 3409 Sunnyvale, California 94088-3409 Telephone 800-234-7381 Philips Semiconductors Philips Electronics North America Corporation register eligible circuits under Semiconductor Chip Protection Act. Copyright Philips Electronics North America Corporation 1996 rights reserved. Printed U.S.A.

Product specification IC20 Data Handbook 1996 Product specificati

Top Searches for this datasheet

Other recent searches