Servo mount Shaft support front rear precision ball bearings Non-stand

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Servo mount Shaft support front rear precision ball bearings Non-stand

Datasheet Thumbnail

Top Searches for this datasheet

Servo mount Shaft support front rear precision ball bearings Non-standard features specifications available Gangable cups
6534 Precision Potentiometer
Electrical Characteristics1
Standard Resistance Range.1 ohms Total Resistance Tolerance .±10 Independent Linearity .±0.5 Effective Electrical Angle .320 Voltage.0.1 maximum (0.25 ohms, ohm) Output Smoothness .0.1 Dielectric Withstanding Voltage (MIL-STD-202, Method 301) Level .750 minimum Power Rating (Voltage Limited Power Dissipation VAC, Whichever Less) °C.1 watt +125 °C.0 watt Insulation Resistance (500 VDC).1,000 megohms minimum Resolution .Essentially infinite
Product Dimensions
5.08 MIN. (.200) 3.170 .000/- .008 DIA. (.1248+.0000/-.0003)
(.010) CHAMFER
22.23 (.875) DIA.
19.050 +.000/ .013 (.75+.0000/-.0005) 1.57 (.062) 1.45 MIN. (.057) 12.70 (1/2 1/32) 5.08 EACH ADDITIONAL CUP. (.200)
Environmental Characteristics1
Operating Temperature Range.+1 +125 Storage Temperature Range.-65 +125 Temperature Coefficient Over Storage Temperature Range .±500 ppm/°C maximum Vibration Wiper Bounce .0.1 millisecond maximum Total Resistance Shift maximum Shock Wiper Bounce .0.1 millisecond maximum Rotational Life Load).25,000,000 shaft revolutions Total Resistance Shift .±10 maximum Moisture Resistance (MIL-STD-202, Method 103, Condition Total Resistance Shift .±10 maximum Rating
12.07 (.475)
1.57 (.062)
MAX.
Mechanical Characteristics1
Mechanical Angle .Continuous Torque (Starting Running) .0.18 N-cm (0.25 oz.-in.) maximum Shaft Runout.0.025 (0.001 in.) T.I.R. Lateral Runout .0.05 (0.002 in.) T.I.R. Shaft Play .0.08 (0.003 in.) T.I.R. Shaft Radial Play .0.08 (0.003 in.) T.I.R. Pilot Diameter Runout.0.025 (0.001 in.) T.I.R. Backlash .0.1 maximum Weight grams Terminals .Side exit turret style Soldering Condition .Recommended hand soldering using Sn95/Ag5 clean solder, 0.025 wire diameter. Maximum temperature (750 seconds. wash process used with clean flux. Marking .Manufacturer's name part number, resistance value tolerance, linearity tolerance, wiring diagram, date code. Ganging.10 cups maximum
15.24 MAX. (.600)
TOLERANCES: EXCEPT WHERE NOTED DECIMALS: .XXX (.02), (.005) FRACTIONS: ±1/64 DIMENSIONS: (IN.)
WIPER
room ambient: nominal relative humidity nominal, except noted.
CLOCKWISE
Recommended Part Numbers Part Number* 6534S-1-102 6534S-1-202 6534S-1-502 6534S-1-103 6534S-1-203 6534S-1-503 6534S-1-104 Resistance 1,000 2,000 5,000 10,000 20,000 50,000 100,000
REV. 04/03 Specifications subject change without notice.

Servo mount Shaft support front rear precision ball bearings Non-stand

Top Searches for this datasheet

Other recent searches