IF-D95 IF-D95T IF-D95OC photologic detectors Industrial Fiber Opt

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

IF-D95 IF-D95T IF-D95OC photologic detectors Industrial Fiber Opt

Datasheet Thumbnail

Top Searches for this datasheet

Plastic Fiber Optic Photologic Detectors
IF-D95
IF-D95T IF-D95OC photologic detectors Industrial Fiber Optics' family low-cost, medium-frequency, short-distance fiber optic LEDs detectors. Each detector consists polycarbonate (PC) housing, internal active element such photodetector subcomponent, cinch hold fiber place. housing optimizes coupling between active element jacketed 1000 plastic fiber. IF-D95T contains photologic detector with totem-pole output IFD95OC similar detector with open-collector option. Both versions contain with photodiode, linear amplifier, voltage regulator, Schmitt trigger. devices feature TTL/CMOS compatible logic level output which drive over supply voltages ranging from volts. Working with this family fiber optics simple: special tools training required. Only sharp knife razor blade needed terminate plastic fiber. When fiber inserted into detector housing, tighten cinch nut. Thereafter, fiber removed simply loosening nut.
Household Appliances Motor Controller Triggering PC-to-Peripheral Links Medical Instruments Automotive Electronics Audio Systems Electronic Games Robotics Communications Reduction Lightning Voltage Transient Susceptablity
Optical Design Required Mates with Standard 1000 Core Jacketed Plastic Fiber Cable Internal Micro-Lens Efficient Coupling Inexpensive Plastic Connector Housing Connector-Less Fiber Termination Connection Interference-Free Transmission from Light-Tight Housing Totem-Pole Open Collector Output Options
Inverting Output Option Available Special Order
25°C)
Operating Storage Temperature Range (TOP, TSTG).-40° 85°C Soldering Temperature from case bottom) (TS) .240°C Supply Voltage, (VS) Voltage Output lead (IF-95OC only) Sinking Current, (IC) Source Current (IO) (IF-95T only) Power Dissipation (PTOT) TA=25°C .100 De-rate Above 25°C .1.33 mW/°C
(TA=25°C)
Parameter
Peak Sensitivity Spectral Sensitivity (S=10% SMAX) Operating Voltage (max) Supply Current (max) Light Required Trigger VCC=5 RL=1k, =660 IF-D95T High Level Output Voltage (IOH= -1.0 Level Output Voltage (IOH= Output Rise Fall Times 10.0 kHz, Loads) (max) Propagation Delay, Low-High, High-Low 10.0 kHz, Loads) IF-D95OC High Level Output Current (VOH=30 Level Output Voltage (IOL=16 Output Rise Fall Times 10.0 kHz, RL=300) (max) Propagation Delay, Low-High, High-Low 10.0 kHz, RL=300 PEAK tPLH, tPHL tPLH, tPHL
Symbol
Value
400-1100 (-30) -2.1 0.34
Unit
µW(dBm)
Industrial Fiber Optics, Inc.
IF-D95
Plastic Fiber Optic Photologic Detectors
FIGURE
Typical detector response versus wavelength.
FIGURE Cross-section fiber optic device.
ends optical fiber with singleedge razor blade sharp knife. obtain precise 90-degree angle (square). Insert fiber through locking into connector until core seats against internal micro-lens. Screw connector locking down snug fit, locking fiber place.
FIGURE
Normalized threshold irradiance amb. temp.
PACKAGE IDENTIFICATION:
D95T- Black housing Yellow D95OC- Black housing Brown Ground Output
FIGURE
Case outline.
Industrial Fiber Optics, Inc.

IF-D95 IF-D95T IF-D95OC photologic detectors Industrial Fiber Opt

Top Searches for this datasheet

Other recent searches