SCOPE Scope. This specification covers performance requirements silico
|
|
|
Top Searches for this datasheet
INCH-POUND MIL-PRF-19500/260F December 1999 SUPERSEDING MIL-PRF-19500/260E August 1999 PERFORMANCE SPECIFICATION SEMICONDUCTOR DEVICE, DIODE, SILICON, POWER RECTIFIER, TYPES 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A VERSIONS JAN, JANTX, JANTXV, JANS, JANHC JANKC 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650, 1N1124RA 1N1126RA, 1N1128RA 1N3649R, 1N3650R ONLY This specification approved Departments Agencies Department Defense.
SCOPE Scope. This specification covers performance requirements silicon semiconductor power rectifier diodes. Four levels product assurance provided each encapsulated 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A device type specified MIL-PRF-19500, levels product assurance each unencapsulated device type. level product assurance provided each device type specified MIL-PRF-19500, 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650. normal reverse suffix) type devices 3.3.1. Physical dimensions. figure (DO-203AA, formerly DO-4) figure (JANHC JANKC). Maximum ratings. 150°C If(surge) 150°C 1/120 Barometric pressure (reduced) mmHg
VRWM
TSTG
1N1202A +200 1N1204A +200 1N1206A +200 1N3671A +200 1N3673A 1000 +200 1N1124A +175 1N1126A +175 1N1128A +175 1N3649 +175 1N3650 1,000 +175 Derate linearly percent 150°C 200°C. 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650 reverse versions have been moved from MIL-S-19500/104, which been canceled, inactive design. Derate linearly dc/°C 50°C 150°C. Primary electrical characteristics. °C/W maximum. Beneficial comments (recommendations, additions, deletions) pertinent data which improving this document should addressed Commander, Defense Supply Center Columbus, ATTN: DSCCVAC, 3990 East Broad St., Columbus, 43216-5000, using addressed Standardization Document Improvement Proposal Form 1426) appearing this document letter. AMSC DISTRIBUTION STATEMENT Approved public release; distribution unlimited. 5961
MIL-PRF-19500/260F
APPLICABLE DOCUMENTS General. documents listed this section specified sections this specification. This section does include documents cited other sections this specification recommended additional information examples. While every effort been made ensure completeness this list, document users cautioned that they must meet specified requirements documents cited section this specification, whether they listed. 2.1.1 Specifications, standards, handbooks. following specifications, standards, handbooks form part this document extent specified herein. Unless otherwise specified, issues these documents those listed issue Department Defense Index Specifications Standards (DODISS) supplement thereto, cited solicitation (see 6.2). SPECIFICATION DEPARTMENT DEFENSE MIL-PRF-19500 STANDARD FEDERAL FED-STD Screw Thread Standards Federal Services Semiconductor Devices, General Specification for.
DEPARTMENT DEFENSE MIL-STD-750 Test Methods Semiconductor Devices.
(Unless otherwise indicated, copies above specifications, standards, handbooks available from Defense Automated Printing Service, Building (DPM-DODSSP), Robbins Avenue, Philadelphia, 191115094.) Order precedence. event conflict between text this specification references cited herein (except associated detail specifications, specification sheets standards), text this specification takes precedence. Nothing this specification, however, supersedes applicable laws regulations unless specific exemption been obtained. REQUIREMENTS Associated specification. individual item requirements shall accordance with MIL-PRF-19500, specified herein. Abbreviations, symbols, definitions. Abbreviations, symbols, definitions used herein shall specified MIL-PRF-19500. Interface requirements physical dimensions. interface requirements physical dimensions shall specified MIL-PRF-19500 figures (DO-203AA, formerly DO-4) figure (JANHC JANKC). 3.3.1 Normal reverse suffix) types. Reverse normal types identical except: normal types have cathode connected stud reverse types have anode connected stud. 3.3.2 Lead finish. Lead finish shall solderable accordance with MIL-PRF-19500, MIL-STD-750 herein. Where choice lead finish desired, shall specified contract purchase order (see 6.2).
MIL-PRF-19500/260F
Dimensions Inches 0.405 0.424 0.424 0.075 0.437 0.175 0.800 0.250 0.060 0.422 0.453 1.52 10.72 11.51 10.77 1.90 Millimeters 10.29 10.77 11.10 4.44 20.32 6.35
Notes
NOTES: Dimensions inches. Metric equivalents given general information only. Units must damaged torque inchpounds applied 10-32NF-2B assembled thread. Diameter unthreaded portion 0.189 inch (4.80 0.163 inch (4.14 min. Complete threads extend within threads seating plane. Angular orientation this terminal undefined. pitch diameter plated threads shall basic pitch diameter 0.169 inch (4.31 reference FEDSTD-H28 (Screw Thread Standards Federal Services.) A.S.A. thread reference 10-32UNF2A. Terminal shape unrestricted.
3,5,7
FIGURE Physical dimensions.(DO-203AA, formerly DO-4). 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A versions, 1N1124A, 1N1126A, 1N1128A, versions 1N3649, 1N3650, versions.
MIL-PRF-19500/260F
Version
Inches 0.116 0.147 0.009
Dimensions Millimeters 2.95 3.73 0.229 3.10 3.89 0.305
0.122 0.153 0.012
NOTES: Dimensions inches. Metric equivalents given general information only. physical characteristics are: Metallization {front (anode), consists thickness 1,200 minimum, thickness 2,000 minimum, thickness 4,000 minimum. Metallization {back, (cathode)} consists thickness 1,200 minimum, thickness 2,000 minimum, thickness 4,000 minimum.
FIGURE Physical dimensions JANHC JANKC. 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A
MIL-PRF-19500/260F
Marking. Marking shall accordance with MIL-PRF-19500. 3.4.1 Polarity. polarity shall indicated graphic symbol with arrow pointing toward negative forward bias. reversed units shall also marked with suffix part number. Electrical performance characteristics. Unless otherwise specified herein, electrical performance characteristics specified 1.3, 1.4, table herein. Electrical test requirements. electrical test requirements shall subgroups specified table herein. Qualification. Devices furnished under this specification shall products that authorized qualifying activity listing applicable qualified manufacturer's list before contract award (see
4.VERIFICATION Classification Inspections. inspection requirements specified herein classified follows: Qualification inspection (see 4.2). Screening (see 4.3) Conformance inspection (see 4.4). 4.1.1 Sampling inspection. Sampling inspection shall accordance with MIL-PRF-19500 herein, except accumulation period shall months lieu weeks. Qualification inspection. Qualification inspection shall accordance with MIL-PRF-19500 herein. 4.2.1 JANHC JANKC devices. Qualification JANHC JANKC devices shall accordance with MIL-PRF-19500.
MIL-PRF-19500/260F
Screening. Screening shall accordance with MIL-PRF-19500 (table IV), specified herein. following measurements shall made accordance with table herein. Devices that exceed limits table herein shall acceptable. Screen (see table MIL-PRF-19500) Measurement JANTX JANTXV levels Surge (see 4.3.1) Thermal response (see 4.3.2) applicable
JANS level Surge (see 4.3.1) Thermal response (see 4.3.2)
applicable
MIL-STD-750, method 1038, test condition hours IR1; Subgroup table herein, V(pk) from initial value; percent from initial value, whichever greater.
MIL-STD-750, method 1038, test condition hours Subgroup table herein, ±0.1 V(pk) from initial value; percent from initial value, whichever greater.
Burn-in, 4.3.3 4.5.1. MIL-STD-750, method 1038, test condition Subgroups table herein; (PK); percent from initial value, whichever greater.
applicable
applicable
Surge shall precede thermal response. These tests shall performed anytime after screen before screen measurement shall indicative open condition. screen shall apply screen JANTX JANTXV.
4.3.1 Surge current. Surge current, MIL-STD-750, method 4066. VRM(w) IFSM 275A; surges; 25°C, surge minute maximum. 4.3.2 Thermal response. thermal response measurements shall performed accordance with method 3101 MIL-STD-750. thermal response conditions maximum thermal response limit shall derived each vendor. chosen thermal response measurement conditions each device qualification shall submitted qualification report thermal response curve shall plotted. chosen thermal response values shall considered final after manufacturer opportunity test five consecutive lots. Heating current (IH) rated 4.3.3 Power burn-in. Power burn-in conditions follows: MIL-STD-750, method 1038, test condition 150°C, (see 4.5.1); rated VRWM (pk) (see 1.3). 4.3.4 Screening (JANHC JANKC). Screening JANHC JANKC shall accordance with MIL-PRF19500. minimum, shall 100-percent probed ensure compliance with group subgroup
MIL-PRF-19500/260F
Conformance inspection. Conformance inspection shall accordance with MIL-PRF-19500, specified herein. 4.4.1 Group inspection. Group inspection shall conducted accordance with MIL-PRF-19500, table herein. 4.4.2 Group inspection. Group inspection shall conducted accordance with conditions specified subgroup testing table (JANS) table (JAN, JANTX, JANTXV) MIL-PRF-19500 paragraphs 4.4.2.1 4.4.2.2 herein. Electrical measurements (end-points) shall accordance with table subgroup herein. Delta measurements shall accordance with table herein. 4.4.2.1 Group inspection, table (JANS) MIL-PRF-19500. Subgroup Method 4066 Condition 150°C; Rated (see 1.3), (surge) 1/120 surges. surge minute maximum. 0.25 Rated applied Rated (see 4.5.2) 2,000 cycles. rated (see 1.3), 125°C; adjusted required chosen give average 275°C (see 4.5.1), 2.0°C/W maximum; rated
1037 1027
3101
4.4.2.2 Group inspection, table (JAN, JANTX JANTXV) MIL-PRF-19500. Subgroup Method 4066 Condition 150°C; Rated (see 1.3), (surge) 1/120 surges. surge minute maximum. 0.25 Rated applied Rated (see 4.5.2) 2,000 cycles. Condition hrs.
1037 1038 1049
required.
4.4.3 Group inspection. Group inspection shall conducted accordance with conditions specified subgroup testing table MIL-PRF-19500 follows. Electrical measurements (end-points) shall accordance with table subgroup herein. Delta measurements shall accordance with table herein. 4.4.3.1 Group inspection, table MIL-PRF-19500. Subgroup Method 1056 2036 2036 2036 Condition Test condition Test condition Weight pounds, Test condition method weight pounds, Test condition seal torque ounce-inches,
MIL-PRF-19500/260F
2036 3101 1037
Test condition stud torque pound-inches, 2.0°C/W maximum; rated 0.25 Rated applied Rated (see 4.5.2) 6,000 cycles.
4.4.4 Group inspection. Group inspection shall conducted accordance with conditions specified subgroup testing table MIL-PRF-19500. Electrical measurements (end-points) shall accordance with table subgroup herein. Delta measurements shall accordance with table herein. 4.4.4.1 Group inspection, table MIL-PRF-19500. Subgroup Method 1056 1038 1049 2101 Condition 100°C, cycles. Condition 1,000 hrs. Sampling plan devices, devices,
Photos cross sections shall submitted devices, qualification report. Vendors shall retain duplicate photos. 2.0°C/W maximum; devices, rated rated (see 1.3), While devices, test being performed, shall monitored shall exceed group limits. Voltage during test 1N1202A 1N1204A 1N1206A 1N3671A 1N3673A 1,000
3101
1001
Methods inspection. Methods inspection shall specified appropriate tables follows. 4.5.1 Burn-in steady-state operation life tests. These tests shall conducted with half-sine waveform specified peak voltage impressed across diode reverse direction followed half-sine waveform specified average rectifier current. forward conduction angle rectified current greater than degrees less than degrees. 4.5.2 intermittent operation life. cycle shall consist "on" period, when power applied suddenly, gradually, device time necessary achieve delta case temperature 85°C +15°C -5°C followed "off" period, when power suddenly removed, cooling. Auxiliary (forced) cooling permitted during period only. tHeating VFPK using sine wave current. full wave current equivalent half sine wave current) shall used power required during period. test power, current, shall least free rating. Within time interval cycles before cycles after termination test, sample units shall removed from specified test conditions allowed reach room ambient conditions. Specified end-point measurements qualification quality conformance inspection shall completed within hours after removal sample units from specified test conditions. Additional readings taken discretion manufacturer.
MIL-PRF-19500/260F
TABLE Group inspection. MIL-STD-750 Inspection Method Subgroup Visual mechanical inspection Subgroup Forward voltage 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A Forward voltage 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650 Reverse current Subgroup High temperature operation: Reverse current 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650 temperature operation Reverse current 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A Subgroups applicable Subgroup Forward voltage Forward voltage footnotes next page. 4011 4011 IFSM IFSM 4026 4016 150°C 4011 (pk) pulse; pulse width <8.5 duty cycle percent pulse 1.35 (pk) 2071 Conditions Symbol Limits Unit
4011
(pulse): msec; method, Rated (dc) (see 1.3)
(pk)
4016
method, Rated VR(pk) (see 1.3)
4016
150°C +5°C, -0°C -65°C method, Rated (dc) (see 1.3)
MIL-PRF-19500/260F
sampling plan, MIL-PRF-19500. shall performed with either This subgroup does apply 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650,
TABLE Groups delta measurements.
Step
Inspection Method
MIL-STD-750 Conditions 4.3.2: 2.0°C/W maximum;
Symbol
Limits
Unit
Thermal response
3101
Forward voltage
4011
maximum change from previous post intermittent life thermal shock measurement tests (JANS only). percent (whichever greater) change from initial Group reading.
Reverse current
4016
method, Rated VR(dc) (see 1.3)
Devices which exceed group limits this test shall rejected. delta electrical measurements table (JANS) MIL-PRF-19500 follows: Subgroup table herein, steps Subgroup table herein, steps Subgroup table herein, step
delta electrical measurements table (JAN, JANTX JANTXV) MIL-PRF-19500 follows: Subgroup table herein, step delta electrical measurements table MIL-PRF-19500 follows: Subgroup table herein, step (JAN, JANTX JANTXV), steps (JANS). Subgroup table herein, steps (JANS), step (JAN, JANTX JANTXV). delta electrical measurements table MIL-PRF-19500 follows: Subgroup table herein, step Subgroup table herein, step
MIL-PRF-19500/260F
PACKAGING Packaging. acquisition purposes, packaging requirements should specified contract order (see 6.2). When actual packaging material performed personnel, these personnel need contact responsible packaging activity ascertain requisite packaging requirements. Packaging requirements maintained Inventory Control Points' packaging activity within Military Department Defense Agency, within Military Departments' System Command. Packaging data retrieval available from managing Military Departments' Defense Agency's automated packaging files, CD-ROM products, contacting responsible packaging activity. NOTES (This section contains information general explanatory nature that helpful, mandatory.) Notes. notes specified MIL-PRF-19500 applicable this specification. Acquisition requirements. Acquisition documents must specify following: Issue DODISS cited solicitation (see 2.1.1). lead finish specified (see 3.3.2). Type designation quality assurance level. Packaging requirements (see 5.1). acquisition, JANHC JANKC letter version must specified (see figure
Suppliers JANHC JANKC die. qualified JANHC JANKC suppliers with applicable letter version (example, JANHCA1N1202A) will identified QML.
JANHC JANKC ordering information Manufacturer 1N1202A 1N1204A 1N1206A 1N3671A 1N3673A 59377 JANHCA1N1202A, JANKCA1N1202A JANHCA1N1204A, JANKCA1N1204A JANHCA1N1206A, JANKCA1N1206A JANHCA1N3671A, JANKCA1N3671A JANHCA1N3673A, JANKCA1N3673A
Qualification. With respect products requiring qualification, awards will made only products which are, time award contract, qualified inclusion Qualified Manufacturer's List QML-19500 whether such products have actually been listed that date. attention contractors called these requirements, manufacturers urged arrange have products that they propose offer Federal Government tested qualification order that they eligible awarded contracts purchase orders products covered this specification. Information pertaining qualification products obtained from Defense Supply Center Columbus, DSCC-VQE, Columbus, 43216. Changes from previous issue. Marginal notations used this revision identify changes with respect previous issue extent changes.
MIL-PRF-19500/260F
Custodians: Army Navy Force NASA Review activities: Army Navy Force
Preparing activity: (Project 5961-2142)
STANDARDIZATION DOCUMENT IMPROVEMENT PROPOSAL INSTRUCTIONS preparing activity must complete blocks block both document number revision letter should given. submitter this form must complete blocks preparing activity must provide reply within days from receipt form. NOTE: This form used request copies documents, request waivers, clarification requirements current contracts. Comments submitted this form constitute imply authorization waive portion referenced document(s) amend contractual requirements. DOCUMENT NUMBER MIL-PRF-19500/260F DOCUMENT DATE December 1999
RECOMMEND CHANGE:
DOCUMENT TITLE SEMICONDUCTOR DEVICE, DIODE, SILICON, POWER RECTIFIER, TYPES 1N1202A, 1N1204A, 1N1206A, 1N3671A, 1N3673A JAN, JANTX, JANTXV, JANS. JANHC JANKC; 1N1124A, 1N1126A, 1N1128A, 1N3649, 1N3650, 1N1124RA, 1N1126RA, 1N1128RA, 1N3649R, 1N3650R ONLY NATURE CHANGE (Identify paragraph number include proposed rewrite, possible. Attach extra sheets needed.)
REASON RECOMMENDATION
SUBMITTER NAME (Last, First, Middle initial)
ORGANIZATION
ADDRESS (Include Code)
TELEPHONE (Include Area Code) COMMERCIAL EMAIL
DATE SUBMITTED
PREPARING ACTIVITY Point Contact Alan Barone ADDRESS Defense Supply Center Columbus, ATTN: DSCC-VAC, 3990 East Broad Street, Columbus, 43213-1999 Form 1426, 1999 (EG) TELEPHONE Commercial EMAIL 614-692-0510 850-0510 614-692-6939 alan_barone@dscc.dla.mil RECEIVE REPLY WITHIN DAYS, CONTACT: Defense Standardization Program Office (DLSC-LM) 8725 John Kingman, Suite 2533, Fort Belvoir, 22060-6221 Telephone (703) 767-6888 427-6888 Previous editions obsolete WHS/DIOR,
Other recent searches
VDE01 - VDE01 VDE01 Datasheet
PTD08A010W - PTD08A010W PTD08A010W Datasheet
Privacy Policy | Disclaimer
© 2012 Datasheet Archive
