Data Sheet August 2002 FN2903.5 100MHz, High Input Impedance, Ver

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Data Sheet August 2002 FN2903.5 100MHz, High Input Impedance, Ver

Datasheet Thumbnail

Top Searches for this datasheet

HA-2620, HA-2625
Data Sheet August 2002 FN2903.5
100MHz, High Input Impedance, Very Wideband, Uncompensated Operational Amplifiers
HA-2620/2625 bipolar operational amplifiers that feature very high input impedance (500M, HA-2620) coupled with wideband performance. high resistance input stage complemented offset voltage (0.5mV, HA-2620) bias offset current (1nA, HA-2620) facilitate accurate signal processing. Input offset reduced further means external nulling potentiometer. 100MHz gain bandwidth product (HA-2620/2625 stable closed loop gains greater than 35V/µs slew rate 150kV/V open loop gain enables HA-2620/2625 perform high gain amplification very fast, wideband signals. These dynamic characteristics, coupled with fast settling times, make these amplifiers ideally suited pulse amplification designs well high frequency (e.g., video) applications. frequency response amplifier tailored exact design requirements means external bandwidth control capacitor connected from Comp GND. addition application pulse video amplifier designs, HA-2620/2625 particularly suited other high performance designs such high-gain distortion audio amplifiers, high-Q wideband active filters highspeed comparators. more information, please refer Application Notes AN509, AN519 AN546.
Features
Gain Bandwidth Product 100MHz High Input Impedance 500M Input Bias Current. Input Offset Current Input Offset Voltage 0.5mV High Gain 150kV/V Slew Rate. 35V/µs Output Short Circuit Protection Compensation Unity Gain Capability
Applications
Video Amplifier Pulse Amplifier Audio Amplifiers Filters High-Q Active Filters High Speed Comparators Distortion Oscillator
Pinouts
HA-2625 (PDIP, SOIC) VIEW
Ordering Information
PART NUMBER (BRAND) HA2-2620-2 HA2-2625-5 HA3-2625-5 HA9P2625-9 (H26259) TEMP. RANGE (oC) PACKAGE Metal Metal PDIP SOIC PKG. T8.C T8.C E8.3 M8.15
COMP
HA-2620, HA-2625 (METAL CAN) VIEW
COMP
CAUTION: These devices sensitive electrostatic discharge; follow proper Handling Procedures. 1-888-INTERSIL 321-724-7143 Intersil (and design) trademark Intersil Americas Inc. Copyright Intersil Americas Inc. 2002. Rights Reserved
HA-2620, HA-2625
Absolute Maximum Ratings
Supply Voltage (Between Terminals) Differential Input Voltage Peak Output Current Full Short Circuit Protection
Thermal Information
Thermal Resistance (Typical, Note (oC/W) (oC/W) PDIP Package SOIC Package Metal Package Maximum Junction Temperature (Hermetic Package) .175oC Maximum Junction Temperature (Plastic Package) .150oC Maximum Storage Temperature Range -65oC 150oC Maximum Lead Temperature (Soldering 10s) 300oC (SOIC Lead Tips Only)
Operating Conditions
Temperature Range HA-2620-2 -55oC 125oC HA-2625-5 75oC HA-2625-9 -40oC 85oC
CAUTION: Stresses above those listed "Absolute Maximum Ratings" cause permanent damage device. This stress only rating operation device these other conditions above those indicated operational sections this specification implied.
NOTE: measured with component mounted evaluation board free air.
Electrical Specifications
PARAMETER INPUT CHARACTERISTICS Offset Voltage (Note Average Offset Voltage Drift Bias Current Offset Current Differential Input Resistance (Note Input Noise Voltage Density 1kHz) Input Noise Current Density 1kHz) Common Mode Range TRANSFER CHARACTERISTICS Large Signal Voltage Gain (Notes Common Mode Rejection Ratio (Note Minimum Stable Gain Gain Bandwidth Product (Notes OUTPUT CHARACTERISTICS Output Voltage Swing (Note Output Current (Note Full Power Bandwidth (Notes
VSUPPLY ±15V, Unless Otherwise Specified TEMP. (oC) Full Full Full Full Full Full Full HA-2620-2 0.16 HA-2625-5, 0.16 UNITS µV/oC nV/Hz pA/Hz kV/V kV/V
Full
TRANSIENT RESPONSE (Note Rise Time (Notes Slew Rate (Notes V/µs
HA-2620, HA-2625
Electrical Specifications
PARAMETER Supply Current Power Supply Rejection Ratio (Note NOTES: This parameter value guaranteed design calculations. Offset externally adjusted zero. VOUT ±10V. ±10V. VOUT 90mV. 40dB Gain. Transient Response Test Circuits Waveforms. (The HA-2620 family stable unity gain without external compensation). ±5V. VOUT ±5V. Slew Rate Full Power Bandwidth guaranteed slew rate measurement: FPBW PEAK VSUPPLY ±15V, Unless Otherwise Specified (Continued) TEMP. (oC) Full HA-2620-2 HA-2625-5, UNITS
POWER SUPPLY CHARACTERISTICS
Test Circuits Waveforms
±40mV INPUT INPUT
±200mV OUTPUT
RISE TIME
OUTPUT
SLEW RATE
NOTE: Measured both positive negative transitions from +200mV -200mV output. TRANSIENT RESPONSE SLEW RATE
100k
1.6k 50pF COMP
NOTE: Tested Offset Adjustment |VOS 1mV| minimum referred output. Typical range ±10mV with 100k. SLEW RATE TRANSIENT RESPONSE SUGGESTED ADJUSTMENT COMPENSATION HOOK-UP
HA-2620, HA-2625 Schematic Diagram
COMPENSATION +INPUT 1.35 2.5K 4.5K 2.0K 1.6K 1.6K 1.6K 4.0K VQ45 4.18K 1.56K 1.56K
16pF
-INPUT
Typical Applications
2.2k +15V 2.2k VOUT +5.0V, 50pF (NOTE) 0.01µF HA-2620 COMP 2.2k HA-2600 100k 50pF (NOTE)
HA-2620
4.25V 1N916 VREF -15V 1N916
OUTPUT
~OUTPUT
FIGURE HIGH INPUT IMPEDANCE COMPARATOR
FIGURE FUNCTION GENERATOR
HA-2620, HA-2625 Typical Applications
(Continued)
2.2k
2620 1MHz GAIN 40dB
VOUT 50pF (NOTE)
NOTE: small load capacitance least 30pF (including stray capacitance) recommended prevent possible high frequency oscillations. FIGURE VIDEO AMPLIFIER
Typical Performance Curves
CURRENT (nA) BIAS
±15V, 25oC, Unless Otherwise Specified
EQUIVALENT INPUT NOISE (µV)
EQUIVALENT INPUT NOISE BANDWIDTH SOURCE RESISTANCE SOURCE RESISTANCE
OFFSET
THERMAL NOISE RESISTOR 100Hz 1kHz 10kHz 100kHz 1MHz UPPER FREQUENCY LOWER FREQUENCY 10Hz 10MHz
TEMPERATURE (oC)
FIGURE INPUT BIAS CURRENT OFFSET CURRENT TEMPERATURE
FIGURE BROADBAND NOISE CHARACTERISTICS
OPEN LOOP VOLTAGE GAIN (dB) GAIN 10Hz 100Hz PHASE 1kHz 10kHz 100kHz FREQUENCY 1MHz 10MHz 100MHz PHASE ANGLE (DEGREES) INPUT IMPEDANCE 1000
TEMPERATURE (oC)
FIGURE OPEN LOOP FREQUENCY RESPONSE
FIGURE INPUT IMPEDANCE TEMPERATURE, 100Hz
HA-2620, HA-2625 Typical Performance Curves
±15V, 25oC, Unless Otherwise Specified (Continued)
OPEN LOOP VOLTAGE GAIN (dB) PEAK VOLTAGE SWING (±V) 10Hz 0.01V 10kHz 100kHz 1MHz FREQUENCY 10MHz 100MHz 115pF 300pF 1000pF
10pF 35pF 50pF
±20V SUPPLY ±15V SUPPLY ±10V SUPPLY 0.1V
100Hz
1kHz
100kHz 10kHz FREQUENCY
1MHz
10MHz
NOTE: External Compensation required closed loop gain external compensation used, also connect 100pF capacitor from output ground. FIGURE OPEN LOOP FREQUENCY RESPONSE VARIOUS VALUES CAPACITORS FROM COMP.
FIGURE OUTPUT VOLTAGE SWING FREQUENCY
-55oC 125oC COMMON MODE RANGE (±V)
±20V SUPPLY GAIN (dB) ±15V SUPPLY ±10V SUPPLY
SUPPLY
SUPPLY VOLTAGE (±V)
TEMPERATURE (oC)
FIGURE COMMON MODE VOLTAGE RANGE SUPPLY VOLTAGE
1000 INPUT NOISE VOLTAGE (nV/Hz)
FIGURE OPEN LOOP VOLTAGE GAIN TEMPERATURE
INPUT NOISE CURRENT (pA/Hz)
INPUT NOISE CURRENT
INPUT NOISE VOLTAGE
FREQUENCY (Hz)
0.01 100K
FIGURE NOISE DENSITY FREQUENCY
HA-2620, HA-2625 Characteristics
DIMENSIONS: mils mils mils 1750µm 1420µm 483µm METALLIZATION: Type: Thickness: SUBSTRATE POTENTIAL (POWERED UP): Unbiased PASSIVATION: Type: Nitride (Si3N4) over Silox (SiO2, Phos.) Silox Thickness: Nitride Thickness: TRANSISTOR COUNT: PROCESS: Bipolar Dielectric Isolation
Metallization Mask Layout
HA-2620, HA-2625
COMP
HA-2620, HA-2625 Dual-In-Line Plastic Packages (PDIP)
INDEX AREA -B-AD BASE PLANE SEATING PLANE 0.010 (0.25) -CA2
E8.3 (JEDEC MS-001-BA ISSUE
LEAD DUAL-IN-LINE PLASTIC PACKAGE INCHES SYMBOL
MILLIMETERS 0.39 2.93 0.356 1.15 0.204 9.01 0.13 7.62 6.10 5.33 4.95 0.558 1.77 0.355 10.16 8.25 7.11 NOTES Rev. 12/93
0.015 0.115 0.014 0.045 0.008 0.355 0.005 0.300 0.240
0.210 0.195 0.022 0.070 0.014 0.400 0.325 0.280
NOTES: Controlling Dimensions: INCH. case conflict between English Metric dimensions, inch dimensions control. Dimensioning tolerancing ANSI Y14.5M-1982. Symbols defined Series Symbol List" Section Publication Dimensions measured with package seated JEDEC seating plane gauge GS-3. dimensions include mold flash protrusions. Mold flash protrusions shall exceed 0.010 inch (0.25mm). measured with leads constrained perpendicular datum measured lead tips with leads unconstrained. must zero greater. maximum dimensions include dambar protrusions. Dambar protrusions shall exceed 0.010 inch (0.25mm). maximum number terminal positions. Corner leads E8.3, E16.3, E18.3, E28.3, E42.6 will have dimension 0.030 0.045 inch (0.76 1.14mm).
0.100 0.300 0.115 0.430 0.150
2.54 7.62 10.92 3.81 2.93
HA-2620, HA-2625 Small Outline Plastic Packages (SOIC)
INDEX AREA SEATING PLANE 0.25(0.010)
M8.15 (JEDEC MS-012-AA ISSUE
LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE INCHES SYMBOL
MILLIMETERS 1.35 0.10 0.33 0.19 4.80 3.80 5.80 0.25 0.40 1.75 0.25 0.51 0.25 5.00 4.00 6.20 0.50 1.27 NOTES Rev. 12/93
0.0532 0.0040 0.013 0.0075 0.1890 0.1497 0.2284 0.0099 0.016
0.0688 0.0098 0.020 0.0098 0.1968 0.1574 0.2440 0.0196 0.050
0.25(0.010)
0.10(0.004)
0.050
1.27
NOTES: Symbols defined Series Symbol List" Section Publication Number Dimensioning tolerancing ANSI Y14.5M-1982. Dimension does include mold flash, protrusions gate burrs. Mold flash, protrusion gate burrs shall exceed 0.15mm (0.006 inch) side. Dimension does include interlead flash protrusions. Interlead flash protrusions shall exceed 0.25mm (0.010 inch) side. chamfer body optional. present, visual index feature must located within crosshatched area. length terminal soldering substrate. number terminal positions. Terminal numbers shown reference only. lead width "B", measured 0.36mm (0.014 inch) greater above seating plane, shall exceed maximum value 0.61mm (0.024 inch). Controlling dimension: MILLIMETER. Converted inch dimensions necessarily exact.
HA-2620, HA-2625 Metal Packages (Can)
REFERENCE PLANE BASE SEATING PLANE BASE METAL LEAD FINISH
T8.C MIL-STD-1835 MACY1-X8 (A1)
LEAD METAL PACKAGE INCHES SYMBOL
MILLIMETERS 4.19 0.41 0.41 0.41 8.51 7.75 2.79 4.70 0.48 0.53 0.61 9.40 8.51 4.06 NOTES Rev. 5/18/94
0.165 0.016 0.016 0.016 0.335 0.305 0.110
0.185 0.019 0.021 0.024 0.375 0.335 0.160
0.200 0.100 0.027 0.027 0.500 0.250 0.010 0.040 0.034 0.045 0.750 0.050 0.045
5.08 2.54 1.02 0.86 1.14 19.05 1.27 1.14 0.69 0.69 12.70 6.35 0.25
SECTION
NOTES: (All leads) applies between applies between 0.500 from reference plane. Diameter uncontrolled beyond 0.500 from reference plane. Measured from maximum diameter product. basic spacing from centerline terminal basic spacing each lead lead position places) from looking bottom package. maximum number terminal positions. Dimensioning tolerancing ANSI Y14.5M 1982. Controlling dimension: INCH.
Intersil semiconductor products manufactured, assembled tested under ISO9000 quality systems certification.
Intersil semiconductor products sold description only. Intersil Corporation reserves right make changes circuit design and/or specifications time without notice. Accordingly, reader cautioned verify that data sheets current before placing orders. Information furnished Intersil believed accurate reliable. However, responsibility assumed Intersil subsidiaries use; infringements patents other rights third parties which result from use. license granted implication otherwise under patent patent rights Intersil subsidiaries.
information regarding Intersil Corporation products, site www.intersil.com

Data Sheet August 2002 FN2903.5 100MHz, High Input Impedance, Ver

Top Searches for this datasheet

Other recent searches