Option Optocouplers Safe Electrical Insulation 0884* These optoco

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Option Optocouplers Safe Electrical Insulation 0884* These optoco

Datasheet Thumbnail

Top Searches for this datasheet

Optocoupler Option
Option Optocouplers Safe Electrical Insulation 0884*
These optocouplers suitable safe electrical insulation only within safety maximum ratings. Compliance with safety maximum ratings must ensured protective circuits. partial discharge measurement ensures that partial discharge occurs during operation maximum permissible operating insulation voltage (VIORM). Permanent partial discharge affects insulating materials result high voltage breakdown. Time-Test Voltage Diagram 0884* recommended that tests with insulation test voltage (VISOL) should made, otherwise partial discharge occur impairing insulation characteristics. Thus partial discharges also occur maximum permissible operating insulation voltage. insulation test 0884 carried after other tests.
INITIAL kV/us IORM
IORM
0.1s 0.1s
measuring time partial dischage
measuring time partial dischage
Procedure Type sampling tests, destructive tests 0884, edition June 1992
Procedure Routine tests, non-destructive tests
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
April 2000-11
Description
Symbol
System DIP4 SFH610A-. SFH615A-. SFH615AA-. SFH615AGB-. SFH615AGR-. SFH617A-. SFH618A-. SFH620A-. SFH620AA-. SFH620AGB-. SFH628A-. SFH6106-. SFH6116-. SFH6156-. SFH6186-. SFH6206-. SFH6286-. DIP8 ILCT6 ILD1/2/5/74 ILD30/31/55 ILD32 ILD66-. ILD250/1/2 ILD255 ILD610-. ILD615-. ILD616-. ILD620-. ILD621GB-. ILD621-. ILD621GB-. ILD755-. ILD766-. MCT6 DIP16 ILQ1/2/5/74 ILQ30/31/55 ILQ32 ILQ66-. ILQ615-. ILQ620-. ILQ620GB-. ILQ621-. ILQ621GB-.
Unit
Installation Category (DIN 0110) Rated Line Voltages VRMS Rated Line Voltages VRMS Rated Line Voltages 1000 VRMS Climatic Category (DIN Part 1/9.80) Pollution Degree (DIN 0110 Part 1/1.89) Maximum Operation Insulating Voltage Test Voltage Input/Output, Procedure 1.875 VIORM, Routine Test, Partial Discharge Test Voltage Input/Output, Procedure VIORM, Type Sampling Test Partial Discharge VIORM 55/100/21 1669
1335 8000 8000
Maximum Permissible Overvoltage (Transient Overvoltage) VIOPartial Discharge Test Voltage VINITIAL Safety Maximum Ratings (Maximum Permissible Ratings Case Fault, also Refer Diagram) Package Temperature Current (Input Current 25°C) Derating with Higher Ambient Temp. Power (Output Total Power Dissipation, 25°C) Derating with Higher Ambient Temp. Insulation Resistance VI/O=500
-1.83 -2.67
mA/K mW/K
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Description
Symbol
System 4N25/26/27/28 4N35/36/37/38/39 4N32/33 CNY17-. CNY17F-. H11A-. H11AA1-. H11B-. H11B1-. H11C-. H11D-. IL1/2/5/74 IL2B-. IL30/31/55 IL55B-. IL66-. IL66B-. IL201/202/203 IL250 IL251 IL252 IL255-. IL400 IL755-. IL755B-. IL766-. IL766B-. MCA230/231 MCA255 MCT2/2E MCT270/271 MCT272 MCT273/274 MCT275 MCT276/277 MCT5210 MCT5211 SFH600-. SFH601-. SFH608-. SFH640-. MOC8050 IL56B-. MOC8021 MOC8112 MOC8102/ 03/04/05
Unit
Installation Category (DIN 0110) Rated Line Voltages VRMS Rated Line Voltages VRMS Rated Line Voltages 1000 VRMS Climatic Category (DIN Part 1/9.80) Pollution Degree (DIN 0110 Part 1/1.89) Maximum Operation Insulating Voltage Test Voltage Input/Output, Procedure 1.875 VIORM, Routine Test, Partial Discharge Test Voltage Input/Output, Procedure VIORM, Type Sampling Test Partial Discharge Partial Discharge Test Voltage Safety Maximum Ratings (Maximum Permissible Ratings Case Fault, also Refer Diagram) Package Temperature Current (Input Current 25°C) Derating with Higher Ambient Temp. Power (Output Total Power Dissipation, 25°C) Derating with Higher Ambient Temp. Insulation Resistance VI/O=500 VIORM I-IV I-IV I-III 55/100/21 1669
1335 8000 8000
Maximum Permissible Overvoltage (Transient Overvoltage) VIOVINITIAL
-2.67 -4.67
mA/K mW/K
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Description
Symbol
System IL410 IL420 IL4116 IL4117 IL4118 IL4216 IL4217 IL4218
System 6N135 6N136 SFH6135 SFH6136 6N138 SFH6138 SFH6139 6N139 SFH6345
System IL300 IL300E IL300F IL300EF IL300DEFG
Unit
Installation Category (DIN 0110) Rated Line Voltages VRMS Rated Line Voltages VRMS Rated Line Voltages 1000 VRMS Climatic Category (DIN Part 1/9.80) Pollution Degree (DIN 0110 Part 1/1.89) Maximum Operation Insulating Voltage Test Voltage Input/Output, Procedure 1.875 VIORM, Routine Test, Partial Discharge Test Voltage Input/Output, Procedure VIORM, Type Sampling Test Partial Discharge Partial Discharge Test Voltage Safety Maximum Ratings (Maximum Permissible Ratings Case Fault, also Refer Diagram) Package Temperature Current (Input Current 25°C) Derating with Higher Ambient Temp. Power (Output Total Power Dissipation, 25°C) Derating with Higher Ambient Temp. Insulation Resistance VI/O=500 Description VIORM I-IV I-III I-II 55/100/21 1594 I-IV I-IV I-III 55/100/21 1181 I-IV I-IV I-III 55/100/21 1669
1275 6000 6000
8000 8000
1335 8000 8000
Maximum Permissible Overvoltage (Transient Overvoltage) VIOVINITIAL
Symbol
-1.65 -3.33 System LH1262 LH1485 LH1500 LH1502
4)5)
-3.33
-1.57 -3.1
mA/K mW/K
Unit
LH1513 LH1514 LH1518 LH1521
LH1531
LH1532 LH1533 LH1535 LH1537 LH1540 LH1541 LH1544 LH1546 LH1547 LH1550 AACTR-X017 AAC-X001
Optocoupler Options 1/2/6/7/8/9
LH1501
LH1520
LH1503 LH1504 LH1505 LH1511
LH1522 LH1523 LH1525 LH1527 AT-X016 AAB-X017
LH1510
LH1526
3)4)
LH1512 AT-X001 AT1-X001
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
LH1530
April 2000-11
Description
Symbol
System AB-X001 BB-X001 CB-X001 AABTR-X017 AAB-X001 AABTR-X001 AT1-X016 AAB1-X016 AAB1-X017 AAB1TR-X017 AAB1-X001 AAB1TR-X001 AB-X016 AAC-X017 AACTR-X001 BB-X016 BAC-X017 BACTR-X017 BAC-X001 BACTR-X001 CB-X016 CAC-X017 CACTR-X017 CAC-X001 CACTR-X001
Unit
Installation Category (DIN 0110) Rated Line Voltages VRMS Rated Line Voltages VRMS Rated Line Voltages 1000 VRMS Climatic Category (DIN Part 1/9.80) Pollution Degree (DIN 0110 Part 1/1.89) Maximum Operation Insulating Voltage Test Voltage Input/Output, Procedure 1.875 VIORM, Routine Test, Partial Discharge Test Voltage Input/Output, Procedure VIORM, Type Sampling Test Partial Discharge VIORM I-IV I-IV I-III 40/85/21 1669 I-IV I-IV I-III 40/85/21 1130 2119
1335 8000 8000
1695 8000 8000
Maximum Permissible Overvoltage (Transient Overvoltage) VIOPartial Discharge Test Voltage VINITIAL Safety Maximum Ratings (Maximum Permissible Ratings Case Fault, also Refer Diagram) Package Temperature Current (Input Current 25°C) Derating with Higher Ambient Temp. Power (Output Total Power Dissipation, 25°C) Derating with Higher Ambient Temp. Insulation Resistance VI/O=500
-4.67
-4.67
mA/K mW/K
voltages referred peak values except otherwise specified. time-test voltage diagram preparation Testing input/output voltage requires input pins output pins shorted.
Option Tested 0884 Option Wide lead spacing (10.16 creepage/clearance distances Option Surface mount leads (creepage/clearance distances Option Surface mount leads CECC 00802, edition soldering conditions devices (option "-." means dash selections.
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Option High-Rel Optocoupler With Very High Long-Term Stability Coupling Factor (CTR)
Each optocoupler tested degradation characteristics (change current transfer ratio). degradation behavior optocouplers tested during short burn-in provides information long-term stability. Only optocouplers showing minimum change current transfer ratio during burn-in supplied. These optocouplers feature excellent long-term stability. Test procedure: First data logging coupling factor (CTRl) IF=1 VCE=5 logged. Load Short-time burn-in: emitter loaded with forward current lF=150 room temperature (25°C) minutes. Second data logging coupling factor (CTR2) IF=1 VCE=5 logged. Evaluation Determination relative change coupling factor: DCTR (%)=100 (1-CTR2/CTRl) change coupling factor DCTR caused burn-in greater than defined range. Thus high longterm stability coupling factor shown graph specified. couplers show similar degradation behavior meaning that even after longer operating time coupling factor spread very wide.
1431 Years
Years
IF=1mA
Years
60mA
300mA
Service life relative temperature current-load Average expected service life extrapolated from laboratory tests. service life defined time when falls initial value. Confidence level 90%.
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Option Optocouplers with 0.4" (10.16 Lead Spread.
leads optocouplers bent according spacing 0.4" (10.16 mm). Dimensions deviating from standard type are: Lead spacing Creepage distance Clearance 10.16 (0.4") >8.0 >8.0
.407 (10.36) .391 (9.96) .307 (7.8) .291 (7.4) .255 (6.5) .248 (6.3)
This version additionally complies with following standards: 0805/05 (System only) Reinforced insulation operating voltage VRMS
.014 (0.35) .010 (0.25)
.400 (10.16) .430 (10.92)
Clearance-creepage distance=8.0 standard version configuration
Option Lead Bends Surface Mount Optocouplers
These optocouplers suitable surface mounting. Dimensions deviating from standard type are: Creepage distance Clearance >8.0 >8.0
.028 (0.7) MIN.
.300 (7.62) TYP. .255 (6.5) .248 (6.3)
.180 (4.6) .160 (4.1)
.020 (0.5) .020 (0.5) .040 (1.02)
This version additionally complies with following standards: 0805/05 (System only) Reinforced insulation operating voltage VRMS During soldering process, package should wetted with tin-lead solder prevent impairment isolation features. Apart from iron soldering, only reflow soldering methods (vapor phase, infrared gas) permissible. Permissible soldering conditions: 260°C seconds 215°C seconds soldering process repeated times most. Attention must paid cooling down device 25°C between soldering processes.
.315 (8.0) MIN. .331 (8.4) MIN. .406 (10.3) MAX.
.300 (7.62) TYP. .268 (6.81) .255 (6.48)
.150 (3.81) .130 (3.30)
4/8/16
.020 (0.50) .000 (0.00)
.016(0.4) typ.
.365 (9.27) MIN. .472 (12.00) MAX.
.015 (0.38) typ.
.031 (0.79)typ. .050(1.27) typ.
Clearance creepage distances must considered solder design. Clearance-creepage distance=8.0 min. standard version configuration.
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Option Lead Bends Surface Mount Optocouplers
These optocouplers suitable surface mounting. Dimensions deviating from standard type are: Creepage distance Clearance >8.0 >8.0
This version additionally complies with following standards: 0805/05 (System only) Reinforced insulation operating voltage VRMS During soldering process, package should wetted with tin-lead solder prevent impairment isolation features. Apart from iron soldering, only reflow soldering methods (vapor phase, infrared gas) permissible. Permissible soldering conditions: 260°C seconds 215°C seconds soldering process repeated times most. Attention must paid cooling down device 25°C between soldering processes.
.300 (7.62) TYP. .255 (6.5) .248 (6.3)
.020 (0.50) .000 (0.00)
.150 (3.81) .130 (3.30)
.020 (0.5) .020 (0.5) .040 (1.02)
.365 (9.27) MIN. .472 (12.00) MAX.
.300 (7.62) TYP. .268 (6.81) .255 (6.48)
.020 (0.50) .000 (0.00)
.150 (3.81) .130 (3.30)
.015 (0.38) typ.
.016(0.4) typ. .031 (0.79)typ. .050(1.27) typ.
.331 (8.4) MIN. .406(10.3) MAX.
Clearance creepage distances must considered solder design. Clearance-creepage distance=8.0 min. standard version configuration.
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11
Option Lead Bends Surface Mount Optocouplers
During soldering process, package should wetted with tin-lead solder prevent impairment isolation features. Apart from iron soldering, only reflow soldering methods (vapor phase, infrared gas) permissible. Permissible soldering conditions: 260°C seconds 215°C seconds soldering process repeated times most. Attention must paid cooling down device 25°C between soldering processes.
.015 (0.38) typ.
.375 (9.53) .395 (10.03) .300 (7.62) ref.
.0040 (.102) .0098 (.249)
.012 (.30) typ.
.020 (.51) .040 (1.02)
max.
.016(0.4) typ. .031 (0.79)typ. .050(1.27) typ.
4/8/16
.020 (0.5) .020 (0.5) .040 (1.02)
2000 Infineon Technologies Corp. Optoelectronics Division Jose, www.infineon.com/opto 1-888-Infineon (1-888-463-4636) OSRAM Opto Semiconductors GmbH Regensburg, Germany www.osram-os.com +49-941-202-7178
Optocoupler Options 1/2/6/7/8/9
April 2000-11

Option Optocouplers Safe Electrical Insulation 0884* These optoco

Top Searches for this datasheet

Other recent searches