Update referenced documents, Edit replace 6.4. Delete substitute PIN,

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Update referenced documents, Edit replace 6.4. Delete substitute PIN,

Datasheet Thumbnail

Top Searches for this datasheet

Update referenced documents, Edit replace 6.4. Delete substitute PIN, editorial changes, update latest DSCC format
DATE
APPROVED
Kendall Cottongim Kendall Cottongim
CURRENT DESIGN ACTIVITY CAGE CODE 037Z3 DEFENSE LOGISTICS AGENCY DEFENSE SUPPLY CENTER COLUMBUS COLUMBUS, OHIO 43216-5000
ORIGINAL FIRST PAGE THIS DRAWING BEEN REPLACED.
Prepared accordance with ASME Y14.100 PAGE STATUS PAGES
Selected item drawing
PAGES
DESIGN ACTIVITY DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, 45444-5000 TITLE FUSE, ENCLOSED LINK; MINIATURE, PRINTED CIRCUIT APPLICATION, NONINDICATING
PMIC
PREPARED David Corbett CHECKED Beymer
Original date drawing
February 1990
APPROVED Randy Larson SIZE CODE IDENT. 14933
89096 PAGE
5920-E052
AMSC DISTRIBUTION STATEMENT Approved public release; distribution unlimited.
SCOPE Scope. This drawing describes requirements family electrical surge arrestors used overvoltages. Part Identifying Number (PIN). complete follows: 89096I Drawing number APPLICABLE DOCUMENTS Government documents. 2.1.1 Specifications, standards, handbooks. following specifications, standards, handbooks form part this document extent specified herein. Unless otherwise specified, issues these documents those listed issue Department Defense Index Specifications Standards (DoDISS) supplement thereto, cited solicitation (see 6.2). SPECIFICATIONS DEPARTMENT DEFENSE DoD-D-1000 MIL-PRF-23419 Drawing, Engineering Associated List. Fuse, Cartridge, Instrument Type, General Specification for. -001 Dash number (See table
(Unless otherwise indicated, copies above specifications, standards, handbooks available from Document Automation Production Service, Building (DPM-DODSSP), Robbins Avenue, Philadelphia, 19111-5094.) Order precedence. event conflict between text this document references cited herein, text this document takes precedence. Nothing this document, however, supersedes applicable laws regulations unless specific exemption been obtained. REQUIREMENTS Drawing precedence. This drawing takes precedence over documents referred herein shall interpreted accordance with DoD-D-1000. Interface physical dimension requirements. figure Mounting. Termination style (see table intended directly soldered onto printed wiring board. Termination style (see table intended used with applicable socket. Socket shall Bussmann PCS-A equivalent. Characteristic. characteristic described "normal" "instantaneous" overload interrupt time accordance with table MIL-PRF-23419. Current rating. table Voltage rating. table Current-carrying capacity. Current-carrying capacity shall percent rating -55°C; percent rating +25°C; percent rating +85°C. temperature rise case, body, terminals shall, point, rise more than +80°C above ambient temperature.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE
Inches .005 .015 .020 .025 .184 .200 .345 .350 NOTES:
0.13 0.38 0.51 0.64 4.67 5.08 8.76 8.89
Dimensions inches. Metric equivalents given general information only. Unless otherwise specified, tolerance ±0.010 (0.25 place decimals ±0.005 (0.13 three place decimals.
FIGURE Design dimensions.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE
TABLE Fuse dash numbers applicable characteristics.
Part identifying number (PIN) 89096 Dimension (see figure Inches 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 0.780 19.81 0.130 3.30 Termination style Maximum voltage rating Current rating (amperes) 1-1/2 2-1/2
Tolerance 0.780 inch dimension ±0.010 (terminal style Tolerance 0.130 inch dimension ±0.020 (terminal style
TABLE Overload interrupt times.
Percent current rating Overload interrupting time -55°C through +85°C Minimum Maximum seconds second
Resistance, maximum cold. table IIl. Overload interrupt. Overload interrupt shall accordance with table MIL-PRF-23419. 3.10 Maximum current clearing When fuses tested, amount ampere-squared seconds passed fuse during melting, arcing clearing shall exceed value specified table III. TABLE III. Fuse overload resistance data.
89096001, 003, 005, 007, 009, 011, 013, 015, Maximum clearing (ampere seconds) volts volts 0.006 0.016 0.020 0.090 0.200 0.300 0.750 7.000 1,000 0.006 0.016 0.020 0.090 0.200 0.300 0.750 5.000 10,000 0.006 0.016 0.020 0.090 0.200 0.300 0.750 5.000 0.006 0.016 0.020 0.090 0.200 0.300 0.750 0.006 0.016 0.020 0.090 0.200 0.300 0.750
Maximum cold resistance (ohms) 1.90 0.85 0.56 0.28 0.17 0.11 0.08 0.026
Measured percent less rated current.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE
3.11 Shock. Shock shall accordance with method MIL-PRF-23419. Termination style shall mounted printed circuit board. Termination style shall mounted applicable socket. 3.12 Thermal shock. Thermal shock shall accordance with method 107, test condition MIL-STD-202. 3.13 Vibration. Vibration shall accordance with method 204, test condition (10-2000 Hz), MIL-STD-202. Termination style shall mounted printed circuit board. Termination style shall mounted applicable socket. 3.14 Moisture resistance. Moisture resistance shall accordance with MIL-PRF-23419. 3.15 Insulation resistance. Insulation resistance shall accordance with MIL-PRF-23419. Following test, insulation resistance shall 10,000 ohms minimum. 3.16 Salt spray. Salt spray shall accordance with MIL-PRF-23419. 3.17 Solderability. Solderability shall accordance with MIL-PRF-23419. 3.18 Resistance soldering heat. Resistance soldering heat shall accordance with MIL-PRF-23419. 3.19 Marking. Fuses shall marked with current voltage rating shown figure Fuses marked with manufacturer's part number, name trademark. unit package shall marked accordance with herein. 3.20 Certificate compliance. certificate compliance shall required from manufacturer order listed suggested source supply (see 6.4). 3.21 Statement lieu group testing. acquiring activity, discretion, accept statement compliance lieu manufacturer performing group inspection (see 6.2c). 3.22 Recycled, recovered, environmentally preferable materials. Recycled, recovered, environmentally preferable materials should used maximum extent possible provided that material meets exceeds operational maintenance requirements, promotes economically advantageous life cycle costs. 3.23 Workmanship. Workmanship shall accordance with MIL-PRF-23419.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE
VERIFICATION Conformance inspection. 4.1.1 Inspection product delivery. Inspection product delivery shall consist group inspection MIL-PRF-23419. 4.1.2 Inspection packaging. Inspection packaging shall accordance with MIL-PRF-23419. 4.1.3 Maximum current clearing maximum clearing shall determined from oscillogram showing current trace. determination shall made application Simpson's rule integrating planimeter shown U.L. Standards 198C, 198D, 198E. Fuses shall subjected symmetrical currents with tolerance +20, percent. power factor shall percent. closing angle shall essentially zero voltage wave (maximum offset) later, produce start arcing within electrical degrees prior system peak voltage. test voltage shall less than rated voltage (see table III). maximum peak voltage occurring during interruption shall more than 3000 volts. This voltage shall measured with instrument having frequency response that linear from hertz. PACKAGING Packaging. acquisition purposes, packaging requirements shall specified contract order (see 6.2). When actual packaging materiel performed personnel, these personnel need contact responsible packaging activity ascertain requisite packaging requirements. Packaging requirements maintained Inventory Control Point's packaging activity within Military Department Defense Agency, within Military Department's System Command. Packaging data retrieval available from managing Military Departments Defense Agency's automated packaging files, CD-ROM products, contacting responsible packaging activity. Marking. unit package shall marked with DSCC drawing (see 1.2), DSCC CAGE code (14933), manufacturer's CAGE code, date code, symbol minimum. NOTES (This section contains information general explanatory nature that helpful, mandatory.) Intended use. Devices conforming this drawing intended when military specifications exist qualified military devices that will perform required function available application. Ordering data. contract purchase order should specify following: Complete (see 1.2). Requirements delivery copy conformance inspection data certificate compliance that parts have passed conformance inspection with each shipment parts manufacturer. Whether manufacturer performs group inspection provides statement compliance lieu performing group inspection (see 3.22). Requirements notification change product contracting activity, applicable. Requirements packaging packing. Users record. Coordination this document future revisions coordinated only with suggested sources supply users record this document. Requests added recorded user this drawing should writing Defense Supply Center, Columbus, ATTN: DSCC/VAT, Post Office 3990, Columbus, 43216-5000 telephone (614) 692-0556 850-0556.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE
Suggested sources supply. Suggested sources supply listed herein. Additional sources will added they become available. assistance this drawing, contact Defense Supply Center, Columbus, ATTN: DSCC-VAT, Post Office 3990, Columbus, 43216-5000 telephone (614)-692-0556 850-0556.
DSCC drawing 89096- Vendor similar designation type number PCB1/2 PCC1/2 PCB3/4 PCC3/4 PCB1 PCC1 PCB1 PCC1 PCB2 PCC2 PCB2 PCC2 PCB3 PCC3 PCD5 PCE5 Vendor CAGE Vendor name address
71400
Bussmann Division
Cooper Industries P.O. 14460 Louis, 63178 (314) 394-2877
Parts must purchased this DSCC assure that performance requirements tests met.
DEFENSE ELECTRONIC SUPPLY CENTER DAYTON, OHIO
SIZE
CODE IDENT 14933
89096
PAGE

Update referenced documents, Edit replace 6.4. Delete substitute PIN,

Top Searches for this datasheet

Other recent searches