Configuring Line Card configure line card Configure Interfaces IP

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Configuring Line Card configure line card Configure Interfaces IP

Datasheet Thumbnail

Top Searches for this datasheet

been initialized that software able communicate with line card.
Configuring Line Card
configure line card Configure Interfaces IPactionSoftware Configuration Guide documentation internet.
Removing Line Card
Loosen screws located both ends faceplate. Grasp finger levers pull line card completely system.
Forwarding Engine DS-3 Channelized Ports
Inserting Line Card
Grasp front line card that going install with faceplate toward component-side left. Pull finger levers towards unlock open) them. Gently slide line card into slot that identified. Push back into chassis until stops.
NOTE: important that insert line card properly into guides chassis. This ensures that connector back line card fits properly into connector backplane. also ensures that line card does against another card (already place) damage gasket across faceplate.
finger levers complete insertion lock board place. Tighten locking screws both ends faceplate ensure good backplane connection.
Customer Support Information
Release Notes: Technical Documentation User Name: Password: E-mail: Phone: ipi/axi540/userdocs/relnotes/ ipi/axi540/userdocs/ torrent fastrouter axi-support@ericsson.com (240) 314-3500 1(800) 996-9544
Quick Reference Guide
Technical Notes On-line updates (get User Name Password from back page)
Control Number EN/LZT 4185/1
gwe, 2.2, 10/1/00
Introduction
Channelized DS-3 forwarding engine provides 75-ohm coaxial DS-3 connections DB-15 DS-1 connection. Each DS-3 port used clear-channel mode subdivided into, from 128, independent channels (i.e. virtual interfaces). DS-1 port, Port presently supported IPactionv2.2 software. When activated subsequent release, Port used injection test streams data port. This forwarding engine installed slot Platform. This Quick Reference Guide will help become familiar with Channelized DS-3 Forwarding Engine.
Figure DS-3 Forwarding Engine
Indicators
This forwarding engine three line card LEDs, reset button, LEDs TX/RX port, four LEDs Craft port five ports (Figure Each port identification number next
Line Card Stat Acty Color Green Green Yellow Green Definition Line card receiving power. Hardware functioning properly Hardware faulty shut down Hardware been initialized software able communicate with line card. Definition Frames being received. Frames being transmitted. DS-3 port enabled. DS-3 port enabled there loss ignal (LOS). DS-3 port enabled. Alarm indication signal DS-3 port. frame error DS-3 port. Far-end receive failure Alarm condition present (not alarm).
Safety Precautions
handle line card unless wearing proper electrostatic discharge equipment. Connect supplied wriststrap equivalent grounded socket lower left corner Platform. remove line card from anti-static shielded until ready install touch connector back line card other electronic components such pins, solder connections, etc. Instead, handle board faceplate edges. operate Platform with open slots. Cover open slots with blank faceplates ensure designed levels shielding airflow. Contact Ericsson Infrastructure obtain additional blank faceplates.
Port EN/LOS
Color Yellow Yellow Green Yellow None Yellow Yellow Yellow Yellow
NOTE: Damage that results from covered warranty provided Ericsson Infras tructure.
Inspect Forwarding Engine Damage
find damage, contact shipping company file report. Then call Ericsson Infrastructure's Customer Support Department (see back page) Return Manufacturer Authorization (RMA) return address product. Lastly, repack card original anti-static packaging shipping carton return shipping carton damaged cannot reused-repack line card carton that provides equivalent protection against static damage breakage.
FERF ALARMS
Record Serial Number(s)
Record serial number(s) found upper right side line card shipping list. will need this information need contact Ericsson Infrastructure's Customer Support (see back page). Serial Number(s)
Visual Checkout with Panel LEDs
Monitor indicators faceplate forwarding engine. When power turned should illuminate immediately. This indicates that line card receiving power. Continue monitor indicators. Stat should illuminate after system determines that hardware functioning properly Acty should illuminate, signifying that hardware

Configuring Line Card configure line card Configure Interfaces IP

Top Searches for this datasheet

Other recent searches