Single-chip 16-bit/32-bit microcontrollers; kB/16 kB/32 flash with ISP

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Single-chip 16-bit/32-bit microcontrollers; kB/16 kB/32 flash with ISP

Datasheet Thumbnail

Top Searches for this datasheet

LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers; kB/16 kB/32 flash with ISP/IAP, fast ports 10-bit
Rev. January 2006 Preliminary data sheet
LPC2101/2102/2103 microcontrollers based 16-bit/32-bit ARM7TDMI-S with real-time emulation that combines microcontroller with embedded high-speed flash memory. 128-bit wide memory interface unique accelerator architecture enable 32-bit code execution maximum clock rate. critical performance interrupt service routines algorithms, this increases performance over Thumb mode. critical code size applications, alternative 16-bit Thumb mode reduces code more than with minimal performance penalty. their tiny size power consumption, LPC2101/2102/2103 ideal applications where miniaturization requirement. blend serial communications interfaces ranging from multiple UARTs, I2C-buses, combined with on-chip SRAM kB/4 kB/8 make these devices very well suited communication gateways protocol converters. superior performance also makes these devices suitable math coprocessors. Various 32-bit 16-bit timers, improved 10-bit ADC, features through output match timers, fast GPIO lines with nine edge level sensitive external interrupt pins make these microcontrollers particularly suitable industrial control medical systems.
Features
features
16-bit/32-bit ARM7TDMI-S microcontroller tiny LQFP48 package. kB/4 kB/8 on-chip static kB/16 kB/32 on-chip flash program memory. 128-bit wide interface/accelerator enables high-speed operation. ISP/IAP on-chip bootloader software. Single flash sector full chip erase programming bytes EmbeddedICE offers real-time debugging with on-chip RealMonitor software. 10-bit converter provides eight analog inputs, with conversion times 2.44 channel dedicated result registers minimize interrupt overhead. 32-bit timers/external event counters with combined seven capture seven compare channels. 16-bit timers/external event counters with combined three capture seven compare channels. power Real-Time Clock (RTC) with independent power dedicated clock input. Multiple serial interfaces including UARTs (16C550), Fast I2C-buses (400 kbit/s), with buffering variable data length capabilities.
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Vectored interrupt controller with configurable priorities vector addresses. thirty-two tolerant fast general purpose pins. edge level sensitive external interrupt pins available. maximum clock available from programmable on-chip with possible input frequency settling time On-chip integrated oscillator operates with external crystal range from MHz. Power saving modes include Idle mode, Power-down mode with active, Power-down mode. Individual enable/disable peripheral functions well peripheral clock scaling additional power optimization. Processor wake-up from Power-down mode external interrupt RTC.
Ordering information
Table Ordering information Package Name LPC2101FBD48 LPC2102FBD48 LPC2103FBD48 LPC2103FA44 LQFP48 LQFP48 LQFP48 PLCC44 Description plastic profile quad flat package; leads; body plastic profile quad flat package; leads; body plastic profile quad flat package; leads; body plastic leaded chip carrier; leads Version SOT313-2 SOT313-2 SOT313-2 SOT187-2 Type number
Ordering options
Table Ordering options Flash memory inputs inputs inputs inputs Temperature range (°C) Type number LPC2101FBD48 LPC2102FBD48 LPC2103FBD48 LPC2103FA44
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Block diagram
TRST XTAL2 VDD(3V3) VDD(1V8) XTAL1
LPC2101/2102/2103
HIGH SPEED GENERAL PURPOSE
TEST/DEBUG INTERFACE
P0[31:0]
BOOT
ARM7TDMI-S
BRIDGE
system clock
SYSTEM FUNCTIONS
ARM7 local
VECTORED INTERRUPT CONTROLLER
AMBA (Advanced High-performance Bus) INTERNAL SRAM CONTROLLER MEMORY ACCELERATOR
kB/4 SRAM
kB/16 FLASH
BRIDGE (ARM peripheral bus)
EINT2 EINT0(1) CAP0(1) CAP1(1) CAP2(1) MAT0(1) MAT1(1) MAT2(1) MAT3(1) AD0[7:0]
EXTERNAL INTERRUPTS
I2C-BUS SERIAL INTERFACES
SCL0, SCL1(1) SDA0, SDA1(1) SCK0, SCK1(1)
CAPTURE/COMPARE EXTERNAL COUNTER TIMER 0/TIMER TIMER 2/TIMER
SERIAL INTERFACES
MOSI0, MOSI1(1) MISO0, MISO1(1) SSEL0, SSEL1(1) TXD0, TXD1(1)
UART0/UART1
RXD0, RXD1(1)
DSR1, CTS1, RTS1, DTR1 DCD1,
RTXC1 RTXC2 VBAT
P0[31:0]
GENERAL PURPOSE
REAL-TIME CLOCK
WATCHDOG TIMER
SYSTEM CONTROL
002aab814
Pins shared with GPIO.
Block diagram
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Pinning information
Pinning
P0.12/DSR1/MAT1.0/AD0.5 P0.11/CTS1/CAP1.1/AD0.4 P0.10/RTS1/CAP1.0/AD0.3 P0.24/AD0.2 P0.23/AD0.1 P0.22/AD0.0 VSSA P0.9/RXD1/MAT2.2 P0.8/TXD1/MAT2.1 P0.7/SSEL0/MAT2.0 DBGSEL RTCK RTXC2 P0.0/TXD0/MAT3.1 P0.1/RXD0/MAT3.2 P0.30/TDI/MAT3.3 P0.31/TDO VDD(3V3) P0.2/SCL0/CAP0.0 RTXC1 P0.3/SDA0/MAT0.0 P0.4/SCK0/CAP0.1 P0.5/MISO0/MAT0.1 P0.6/MOSI0/CAP0.2
002aab821
Koninklijke Philips Electronics N.V. 2006. rights reserved.
P0.14/DCD1/SCK1/EINT1
P0.16/EINT0/MAT0.2
P0.13/DTR1/MAT1.1
P0.18/CAP1.3/SDA1
P0.17/CAP1.2/SCL1
P0.15/RI1/EINT2
P0.19/MAT1.2/MISO1 P0.20/MAT1.3/MOSI1 P0.21/SSEL1/MAT3.0 VBAT VDD(1V8) P0.27/TRST/CAP2.0 P0.28/TMS/CAP2.1
LPC2101/2102/2103
P0.29/TCK/CAP2.2
LQFP48 configuration
LPC2101_02_03_1
Preliminary data sheet
Rev. January 2006
P0.25/AD0.6
P0.26/AD0.7
VDD(3V3)
VDDA
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
P0.19/MAT1.2/MISO1 P0.20/MAT1.3/MOSI1 P0.21/SSEL1/MAT3.0
P0.12/DSR1/MAT1.0/AD0.5 P0.11/CTS1/CAP1.1/AD0.4 P0.10/RTS1/CAP1.0/AD0.3 P0.24/AD0.2 P0.23/AD0.1 P0.22/AD0.0 VSSA P0.9/RXD1/MAT2.2 P0.8/TXD1/MAT2.1 P0.7/SSEL0/MAT2.0 DBGSEL RTXC2 P0.6/MOSI0/CAP0.2
002aab920
Koninklijke Philips Electronics N.V. 2006. rights reserved.
P0.14/DCD1/SCK1/EINT1
P0.16/EINT0/MAT0.2
P0.13/DTR1/MAT1.1 P0.3/SDA0/MAT0.0
P0.18/CAP1.3/SDA1
P0.17/CAP1.2/SCL1
P0.15/RI1/EINT2
VDD(1V8) P0.27/TRST/CAP2.0 P0.28/TMS/CAP2.1 P0.29/TCK/CAP2.2 P0.0/TXD0/MAT3.1 P0.1/RXD0/MAT3.2 P0.30/TDI/MAT3.3 P0.31/TDO P0.2/SCL0/CAP0.0 RTXC1 P0.4/SCK0/CAP0.1 P0.5/MISO0/MAT0.1
LPC2101/2102/2103
PLCC44 configuration
LPC2101_02_03_1
Preliminary data sheet
Rev. January 2006
P0.25/AD0.6
VDD(3V3)
VDDA
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
description
Table Symbol P0.0 P0.31 description LQFP48 PLCC44 Type Description Port Port 32-bit port with individual direction controls each bit. total pins Port used general purpose bidirectional digital I/Os while P0.31 output only pin. operation port pins depends upon function selected connect block. P0.0 General purpose Input/output digital (GPIO). TXD0 Transmitter output UART0. MAT3.1 output Timer P0.1 General purpose Input/output digital (GPIO). RXD0 Receiver input UART0. MAT3.2 output Timer P0.2 General purpose Input/output digital (GPIO). SCL0 I2C0 clock Input/output. Open-drain output (for I2C-bus compliance). CAP0.0 Capture input Timer channel P0.3 General purpose Input/output digital (GPIO). SDA0 I2C0 data input/output. Open-drain output (for I2C-bus compliance). MAT0.0 output Timer channel P0.4 General purpose Input/output digital (GPIO). SCK0 Serial clock SPI0. clock output from master input slave. CAP0.1 Capture input Timer channel P0.5 General purpose Input/output digital (GPIO). MISO0 Master Slave SPI0. Data input master data output from slave. MAT0.1 output Timer channel P0.6 General purpose Input/output digital (GPIO). MOSI0 Master Slave SPI0. Data output from master data input slave. CAP0.2 Capture input Timer channel P0.7 General purpose Input/output digital (GPIO). SSEL0 Slave Select SPI0. Selects interface slave. MAT2.0 output Timer channel P0.8 General purpose Input/output digital (GPIO). TXD1 Transmitter output UART1. MAT2.1 output Timer channel P0.9 General purpose Input/output digital (GPIO). RXD1 Receiver input UART1. MAT2.2 output Timer channel
P0.0/TXD0/ MAT3.1
P0.1/RXD0/ MAT3.2
P0.2/SCL0/ CAP0.0
P0.3/SDA0/ MAT0.0
P0.4/SCK0/ CAP0.1
P0.5/MISO0/ MAT0.1
P0.6/MOSI0/ CAP0.2
P0.7/SSEL0/ MAT2.0
P0.8/TXD1/ MAT2.1
P0.9/RXD1/ MAT2.2
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Table Symbol
description .continued LQFP48 PLCC44 Type Description P0.10 General purpose Input/output digital (GPIO). RTS1 Request Send output UART1. CAP1.0 Capture input Timer channel AD0.3 input P0.11 General purpose Input/output digital (GPIO). CTS1 Clear Send input UART1. CAP1.1 Capture input Timer channel AD0.4 input P0.12 General purpose Input/output digital (GPIO). DSR1 Data Ready input UART1. MAT1.0 output Timer channel AD0.5 input P0.13 General purpose Input/output digital (GPIO). DTR1 Data Terminal Ready output UART1. MAT1.1 output Timer channel P0.14 General purpose Input/output digital (GPIO). DCD1 Data Carrier Detect input UART1. SCK1 Serial Clock SPI1. clock output from master input slave. EINT1 External interrupt input. P0.15 General purpose Input/output digital (GPIO). Ring Indicator input UART1. EINT2 External interrupt input. P0.16 General purpose Input/output digital (GPIO). EINT0 External interrupt input. MAT0.2 output Timer channel P0.17 General purpose Input/output digital (GPIO). CAP1.2 Capture input Timer channel SCL1 I2C1 clock Input/output. Open-drain output (for I2C-bus compliance). P0.18 General purpose Input/output digital (GPIO). CAP1.3 Capture input Timer channel SDA1 I2C1 data Input/output. Open-drain output (for I2C-bus compliance). P0.19 General purpose Input/output digital (GPIO). MAT1.2 output Timer channel MISO1 Master Slave SSP. Data input master data output from slave. P0.20 General purpose Input/output digital (GPIO). MAT1.3 output Timer channel MOSI1 Master Slave SSP. Data output from master data input slave.
Koninklijke Philips Electronics N.V. 2006. rights reserved.
P0.10/RTS1/ CAP1.0/AD0.3
P0.11/CTS1/ CAP1.1/AD0.4
P0.12/DSR1/ MAT1.0/AD0.5
P0.13/DTR1/ MAT1.1
P0.14/DCD1/ SCK1/EINT1
P0.15/RI1/ EINT2
P0.16/EINT0/ MAT0.2
P0.17/CAP1.2/ SCL1
P0.18/CAP1.3/ SDA1
P0.19/MAT1.2/ MISO1
P0.20/MAT1.3/ MOSI1
LPC2101_02_03_1
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Table Symbol
description .continued LQFP48 PLCC44 Type Description P0.21 General purpose Input/output digital (GPIO). SSEL1 Slave Select SPI1. Selects interface slave. MAT3.0 output Timer channel P0.22 General purpose Input/output digital (GPIO). AD0.0 input P0.23 General purpose Input/output digital (GPIO). AD0.1 input P0.24 General purpose Input/output digital (GPIO). AD0.2 input P0.25 General purpose Input/output digital (GPIO). AD0.6 input P0.26 General purpose Input/output digital (GPIO). AD0.7 input P0.27 General purpose Input/output digital (GPIO). TRST Test Reset JTAG interface. CAP2.0 Capture input Timer channel P0.28 General purpose Input/output digital (GPIO). Test Mode Select JTAG interface. CAP2.1 Capture input Timer channel P0.29 General purpose Input/output digital (GPIO). Test Clock JTAG interface. CAP2.2 Capture input Timer channel P0.30 General purpose Input/output digital (GPIO). Test Data JTAG interface. MAT3.3 output Timer P0.31 General purpose output only digital (GPIO). Test Data JTAG interface. Input oscillator circuit. Output from oscillator circuit. Returned test clock output: Extra signal added JTAG port. Assists debugger synchronization when processor frequency varies. Bidirectional with internal pull-up. Input oscillator circuit internal clock generator circuits. Output from oscillator amplifier. Debug select: When LOW, part operates normally. When HIGH, debug mode entered. Input with internal pull-down. External reset input: this resets device, causing ports peripherals take their default states processor execution begin address with hysteresis, tolerant. Ground: reference.
Koninklijke Philips Electronics N.V. 2006. rights reserved.
P0.21/SSEL1/ MAT3.0
P0.22/AD0.0 P0.23/AD0.1 P0.24/AD0.2 P0.25/AD0.6 P0.26/AD0.7 P0.27/TRST/ CAP2.0
n.c.
P0.28/TMS/ CAP2.1
P0.29/TCK/ CAP2.2
P0.30/TDI/ MAT3.3
P0.31/TDO RTXC1 RTXC2 RTCK
n.c.
DBGSEL
LPC2101_02_03_1
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Table Symbol VSSA
description .continued LQFP48 PLCC44 Type Description Analog ground: reference. This should nominally same voltage should isolated minimize noise error. Analog power supply: This should nominally same voltage VDD(3V3) should isolated minimize noise error. This voltage used power on-chip PLL. This also provides voltage reference level ADC. core power supply: This power supply voltage internal circuitry. power supply: This power supply voltage ports. power supply: this supplies power RTC.
VDDA
VDD(1V8) VDD(3V3) VBAT
n.c.
tolerant providing digital functions with levels hysteresis slew rate control. tolerant providing digital functions with levels hysteresis slew rate control. configured input function, this utilizes built-in glitch filter that blocks pulses shorter than Open-drain tolerant digital I2C-bus specification compatible pad. requires external pull-up provide output functionality. tolerant providing digital (with levels hysteresis slew rate control) analog input function. configured input function, this utilizes built-in glitch filter that blocks pulses shorter than When configured input, digital section disabled. provides special analog functionality.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Functional description
Architectural overview
ARM7TDMI-S general purpose 32-bit microprocessor, which offers high performance very power consumption. architecture based Reduced Instruction Computer (RISC) principles, instruction related decode mechanism much simpler than those microprogrammed Complex Instruction Computers (CISC). This simplicity results high instruction throughput impressive real-time interrupt response from small cost-effective processor core. Pipeline techniques employed that parts processing memory systems operate continuously. Typically, while instruction being executed, successor being decoded, third instruction being fetched from memory. ARM7TDMI-S processor also employs unique architectural strategy known Thumb, which makes ideally suited high-volume applications with memory restrictions, applications where code density issue. idea behind Thumb that super-reduced instruction set. Essentially, ARM7TDMI-S processor instruction sets:
standard 32-bit set. 16-bit Thumb set.
Thumb set's 16-bit instruction length allows approach twice density standard code while retaining most ARM's performance advantage over traditional 16-bit processor using 16-bit registers. This possible because Thumb code operates same 32-bit register code. Thumb code able provide code size ARM, performance equivalent processor connected 16-bit memory system. particular flash implementation LPC2101/2102/2103 allows full speed execution also mode. recommended program performance critical short code sections mode. impact overall code size will minimal speed increased over Thumb mode.
On-chip flash program memory
LPC2101/2102/2103 incorporate flash memory system respectively. This memory used both code data storage. Programming flash memory accomplished several ways. programmed System serial port. application program also erase and/or program flash while application running, allowing great degree flexibility data storage field firmware upgrades, etc. entire flash memory available user code bootloader resides separate memory. LPC2101/2102/2103 flash memory provides minimum 100,000 erase/write cycles years data-retention memory.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
On-chip static
On-chip static used code and/or data storage. SRAM accessed 8-bits, 16-bits, 32-bits. LPC2101/2102/2103 provide static RAM.
Memory
LPC2101/2102/2103 memory incorporates several distinct regions, shown Figure addition, interrupt vectors re-mapped allow them reside either flash memory (the default) on-chip static RAM. This described Section 6.17 "System control".
PERIPHERALS 3.75 PERIPHERALS
0xFFFF FFFF 0xF000 0000 0xE000 0000
RESERVED ADDRESS SPACE
0xC000 0000
BOOT BLOCK RESERVED ADDRESS SPACE
0x8000 0000 0x7FFF FFFF 0x7FFF E000 0x7FFF DFFF 0x4000 2000 0x4000 1FFF
ON-CHIP STATIC (LPC2103) ON-CHIP STATIC (LPC2102) ON-CHIP STATIC (LPC2101) RESERVED ADDRESS SPACE ON-CHIP NON-VOLATILE MEMORY (LPC2103) ON-CHIP NON-VOLATILE MEMORY (LPC2102) ON-CHIP NON-VOLATILE MEMORY (LPC2101)
0x4000 1000 0x4000 0FFF 0x4000 0800 0x4000 07FF 0x4000 0000 0x0000 8000 0x0000 7FFF 0x0000 4000 0x0000 3FFF 0x0000 2000 0x0000 1FFF 0x0000 0000
002aab822
LPC2101/2102/2103 memory
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Interrupt controller
accepts interrupt request inputs categorizes them FIQ, vectored IRQ, non-vectored defined programmable settings. programmable assignment scheme means that priorities interrupts from various peripherals dynamically assigned adjusted. highest priority. more than request assigned FIQ, combines requests produce signal processor. fastest possible latency achieved when only request classified FIQ, because then service routine does need branch into interrupt service routine from interrupt vector location. more than request assigned class, service routine will read word from that identifies which source(s) (are) requesting interrupt. Vectored IRQs have middle priority. Sixteen interrupt requests assigned this category. interrupt requests assigned vectored slots, among which slot highest priority slot lowest. Non-vectored IRQs have lowest priority. combines requests from vectored non-vectored IRQs produce signal processor. service routine start reading register from jumping there. vectored IRQs pending, provides address highest-priority requesting IRQs service routine, otherwise provides address default routine that shared non-vectored IRQs. default routine read another register what IRQs active.
6.5.1 Interrupt sources
Each peripheral device interrupt line connected Vectored Interrupt Controller, have several internal interrupt flags. Individual interrupt flags also represent more than interrupt source.
connect block
connect block allows selected pins microcontroller have more than function. Configuration registers control multiplexers allow connection between chip peripherals. Peripherals should connected appropriate pins prior being activated, prior related interrupt(s) being enabled. Activity enabled peripheral function that mapped related should considered undefined. Control Module with select registers defines functionality microcontroller given hardware environment. After reset pins Port configured input with following exceptions: debug enabled, JTAG pins will assume their JTAG functionality. pins associated with I2C0 interface open-drain.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Fast general purpose parallel
Device pins that connected specific peripheral function controlled GPIO registers. Pins dynamically configured inputs outputs. Separate registers allow setting clearing number outputs simultaneously. value output register read back, well current state port pins. LPC2101/2102/2103 introduce accelerated GPIO functions over prior LPC2000 devices:
GPIO registers relocated local fastest possible timing. Mask registers allow treating sets port bits group, leaving other bits
unchanged.
GPIO registers byte addressable. Entire port value written instruction.
6.7.1 Features
Bit-level clear registers allow single instruction clear number
bits port.
Direction control individual bits. Separate control output clear. default inputs after reset. 10-bit converter
LPC2101/2102/2103 contain analog digital converter. single 10-bit successive approximation analog digital converter with eight channels.
6.8.1 Features
Measurement range Each converter capable performing more than 400,000 10-bit samples second. Burst conversion mode single multiple inputs. Optional conversion transition input Timer Match signal. Every analog input dedicated result register reduce interrupt overhead.
UARTs
LPC2101/2102/2103 each contain UARTs. addition standard transmit receive data lines, UART1 also provides full modem control handshake interface. Compared previous LPC2000 microcontrollers, UARTs LPC2101/2102/2103 include fractional baud rate generator both UARTs. Standard baud rates such 115200 achieved with crystal frequency above MHz.
6.9.1 Features
byte Receive Transmit FIFOs. Register locations conform `550 industry standard. Receiver FIFO trigger points bytes
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Built-in fractional baud rate generator covering wide range baud rates without
need external crystals particular values.
Transmission FIFO control enables implementation software (XON/XOFF) flow
control both UARTs.
UART1 equipped with standard modem interface signals. This module also
provides full support hardware flow control (auto-CTS/RTS).
6.10 I2C-bus serial controllers
LPC2101/2102/2103 each contain I2C-bus controllers. I2C-bus bidirectional, inter-IC control using only wires: Serial Clock Line (SCL), Serial Data Line (SDA). Each device recognized unique address operate either receiver-only device (e.g., driver) transmitter with capability both receive send information such serial memory. Transmitters and/or receivers operate either master slave mode, depending whether chip initiate data transfer only addressed. I2C-bus multi-master bus, controlled more than master connected I2C-bus implemented LPC2101/2102/2103 supports rates kbit/s (Fast I2C).
6.10.1 Features
Compliant with standard I2C-bus interface. Easy configure Master, Slave, Master/Slave. Programmable clocks allow versatile rate control. Bidirectional data transfer between masters slaves. Multi-master central master). Arbitration between simultaneously transmitting masters without corruption serial data bus. serial bus.
Serial clock synchronization allows devices with different rates communicate Serial clock synchronization used handshake mechanism suspend
resume serial transfer.
I2C-bus also used test diagnostic purposes. 6.11 serial controller
LPC2101/2102/2103 each contain controller. full duplex serial interface, designed handle multiple masters slaves connected given bus. Only single master single slave communicate interface during given data transfer. During data transfer master always sends bits bits data slave, slave always sends bits bits data master.
6.11.1 Features
Compliant with specification. Synchronous, Serial, Full Duplex, Communication.
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Combined master slave. Maximum data rate eighth input clock rate. 6.12 serial controller
LPC2101/2102/2103 each contain SSP. controller capable operation SPI, 4-wire SSI, Microwire bus. interact with multiple masters slaves bus. However, only single master single slave communicate during given data transfer. supports full duplex transfers, with data frames bits bits flowing from master slave from slave master. Often only these data streams carries meaningful data.
6.12.1 Features
Compatible with Motorola SPI, 4-wire TI's National Semiconductor's
Microwire buses.
Synchronous Serial Communication. Master slave operation. 8-frame FIFOs both transmit receive. Four bits bits frame.
6.13 General purpose 32-bit timers/external event counters
Timer/Counter designed count cycles peripheral clock (PCLK) externally supplied clock optionally generate interrupts perform other actions specified timer values, based four match registers. also includes four capture inputs trap timer value when input signal transitions, optionally generating interrupt. Multiple pins selected perform single capture match function, providing application with `or' `and', well `broadcast' functions among them. LPC2101/2102/2103 count external events capture inputs minimum external pulse equal longer than period PCLK. this configuration, unused capture lines selected regular timer capture inputs used external interrupts.
6.13.1 Features
32-bit timer/counter with programmable 32-bit prescaler. External event counter timer operation. Four 32-bit capture channels timer/counter that take snapshot timer
value when input signal transitions. capture event also optionally generate interrupt.
Four 32-bit match registers that allow:
Continuous operation with optional interrupt generation match. Stop timer match with optional interrupt generation. Reset timer match with optional interrupt generation.
Four external outputs timer/counter corresponding match registers, with
following capabilities: match.
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
HIGH match. Toggle match. nothing match.
6.14 General purpose 16-bit timers/external event counters
Timer/Counter designed count cycles peripheral clock (PCLK) externally supplied clock optionally generate interrupts perform other actions specified timer values, based four match registers. also includes three capture inputs trap timer value when input signal transitions, optionally generating interrupt. Multiple pins selected perform single capture match function, providing application with `or' `and', well `broadcast' functions among them. LPC2101/2102/2103 count external events capture inputs minimum external pulse equal longer than period PCLK. this configuration, unused capture lines selected regular timer capture inputs used external interrupts.
6.14.1 Features
16-bit timer/counters with programmable 16-bit prescaler. External event counter timer operation. Three 16-bit capture channels that take snapshot timer value when
input signal transitions. capture event also optionally generate interrupt.
Four 16-bit match registers that allow:
Continuous operation with optional interrupt generation match. Stop timer match with optional interrupt generation. Reset timer match with optional interrupt generation.
Four external outputs timer/counter corresponding match registers, with
following capabilities: match. HIGH match. Toggle match. nothing match.
6.15 Watchdog timer
purpose watchdog reset microcontroller within reasonable amount time enters erroneous state. When enabled, watchdog will generate system reset user program fails `feed' reload) watchdog within predetermined amount time.
6.15.1 Features
Internally resets chip periodically reloaded. Debug mode. Enabled software requires hardware reset watchdog reset/interrupt
disabled.
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Incorrect/Incomplete feed sequence causes reset/interrupt enabled. Flag indicate watchdog reset. Programmable 32-bit timer with internal pre-scaler. Selectable time period from (TPCLK (TPCLK multiples TPCLK
6.16 Real-time clock
Real-Time Clock (RTC) designed provide counters measure time when normal idle operating mode selected. been designed little power, making suitable battery powered systems where running continuously (Idle mode).
6.16.1 Features
Measures passage time maintain calendar clock. Ultra-low power design support battery powered systems. Provides Seconds, Minutes, Hours, Month, Month, Year, Week,
Year.
either dedicated oscillator input clock derived from
external crystal/oscillator input XTAL1. Programmable Reference Clock Divider allows fine adjustment RTC.
Dedicated power supply connected battery main 6.17 System control
6.17.1 Crystal oscillator
On-chip integrated oscillator operates with external crystal range MHz. oscillator output frequency called fosc processor clock frequency referred CCLK purposes rate equations, etc. fosc CCLK same value unless running connected. Refer Section 6.17.2 "PLL" additional information.
6.17.2
accepts input clock frequency range MHz. input frequency multiplied into range with Current Controlled Oscillator (CCO). multiplier integer value from practice, multiplier value cannot higher than this family microcontrollers upper frequency limit CPU). operates range MHz, there additional divider loop keep within frequency range while providing desired output frequency. output divider divide produce output clock. Since minimum output divider value insured that output duty cycle. turned bypassed following chip reset enabled software. program must configure activate PLL, wait Lock, then connect clock source. settling time
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
6.17.3 Reset wake-up timer
Reset sources LPC2101/2102/2103: RESET watchdog reset. RESET Schmitt trigger input with additional glitch filter. Assertion chip reset source starts wake-up timer (see wake-up timer description below), causing internal chip reset remain asserted until external reset de-asserted, oscillator running, fixed number clocks have passed, on-chip flash controller completed initialization. When internal reset removed, processor begins executing address which reset vector. that point, processor peripheral registers have been initialized predetermined reset values. wake-up timer ensures that oscillator other analog functions required chip operation fully functional before processor allowed execute instructions. This important power types reset, whenever aforementioned functions turned reason. Since oscillator other functions turned during Power-down mode, wake-up processor from Power-down mode makes wake-up timer. wake-up timer monitors crystal oscillator means checking whether safe begin code execution. When power applied chip, some event caused chip exit Power-down mode, some time required oscillator produce signal sufficient amplitude drive clock logic. amount time depends many factors, including rate ramp case power on), type crystal electrical characteristics quartz crystal used), well other external circuitry (e.g., capacitors), characteristics oscillator itself under existing ambient conditions.
6.17.4 Code security
This feature LPC2101/2102/2103 allow application control whether debugged protected from observation. after reset on-chip bootloader detects valid checksum flash reads 0x8765 4321 from address 0x1FC flash, debugging will disabled thus code flash will protected from observation. Once debugging disabled, only enabled performing full chip erase using ISP.
6.17.5 External interrupt inputs
LPC2101/2102/2103 include three edge level sensitive External Interrupt Inputs selectable functions. When pins combined, external events processed three independent interrupt signals. External Interrupt Inputs optionally used wake-up processor from Power-down mode. Additionally capture input pins also used external interrupts without option wake device from Power-down mode.
6.17.6 Memory mapping control
Memory Mapping Control alters mapping interrupt vectors that appear beginning address 0x0000 0000. Vectors mapped bottom on-chip flash memory, on-chip static RAM. This allows code running different memory spaces have control interrupts.
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
6.17.7 Power control
LPC2101/2102/2103 supports reduced power modes: Idle mode Power-down mode. Idle mode, execution instructions suspended until either reset interrupt occurs. Peripheral functions continue operation during Idle mode generate interrupts cause processor resume execution. Idle mode eliminates power used processor itself, memory systems related controllers, internal buses. Power-down mode, oscillator shut down chip receives internal clocks. processor state registers, peripheral registers, internal SRAM values preserved throughout Power-down mode logic levels chip output pins remain static. Power-down mode terminated normal operation resumed either reset certain specific interrupts that able function without clocks. Since dynamic operation chip suspended, Power-down mode reduces chip power consumption nearly zero. Selecting external clock instead PCLK clock-source on-chip will enable microcontroller have active during Power-down mode. Power-down current increased with active. However, significantly lower than Idle mode. Power Control Peripherals feature allows individual peripherals turned they needed application, resulting additional power savings during active Idle mode.
6.17.8
divider determines relationship between processor clock (CCLK) clock used peripheral devices (PCLK). divider serves purposes. first provide peripherals with desired PCLK that they operate speed chosen processor. order achieve this, slowed down processor clock rate. Because must work properly power-up (and timing cannot altered does work since divider control registers reside bus), default condition reset processor clock rate. second purpose divider allow power savings when application does require peripherals full processor rate. Because divider connected output, remains active running) during Idle mode.
6.18 Emulation debugging
LPC2101/2102/2103 support emulation debugging JTAG serial port.
6.18.1 EmbeddedICE
Standard EmbeddedICE logic provides on-chip debug support. debugging target system requires host computer running debugger software EmbeddedICE protocol convertor. EmbeddedICE protocol convertor converts Remote Debug Protocol commands JTAG data needed access core. core Debug Communication Channel function built-in. debug communication channel allows program running target communicate with host debugger another separate host without stopping program flow even
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
entering debug state. debug communication channel accessed co-processor program running ARM7TDMI-S core. debug communication channel allows JTAG port used sending receiving data without affecting normal program flow. debug communication channel data control registers mapped addresses EmbeddedICE logic.
6.18.2 RealMonitor
RealMonitor configurable software module, developed Inc., which enables real time debug. lightweight debug monitor that runs background while users debug their foreground application. communicates with host using DCC, which present EmbeddedICE logic. LPC2101/2102/2103 contain specific configuration RealMonitor software programmed into on-chip boot memory.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Limiting values
Table Limiting values accordance with Absolute Maximum Rating System (IEC 60134). Symbol VDD(1V8) VDD(3V3) VDDA Vi(VBAT) Parameter supply voltage (1.8 supply voltage (3.3 analog supply voltage input voltage VBAT analog input voltage input voltage tolerant pins other pins Tstg Ptot(pack) supply current ground current storage temperature total power dissipation (per package) based package heat transfer, device power consumption
Conditions
-0.5 -0.5 -0.5 -0.5 -0.5 -0.5 -0.5
+2.5 +3.6
Unit
[10] [11]
following applies Limiting values: This product includes circuitry specifically designed protection internal devices from damaging effects excessive static charge. Nonetheless, suggested that conventional precautions taken avoid applying greater than rated maximum. Parameters valid over operating temperature range unless otherwise specified. voltages with respect unless otherwise noted. Core internal rail. External rail. related pins. Including voltage outputs 3-state mode. Only valid when VDD(3V3) supply voltage present. exceed supply pin. peak current limited times corresponding maximum current.
[10] ground pin. [11] Dependent package type.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Static characteristics
Table Static characteristics commercial applications, unless otherwise specified. Symbol VDD(1V8) VDD(3V3) VDDA Vi(VBAT) Ilatch Parameter supply voltage (1.8 supply voltage (3.3 analog supply voltage input voltage VBAT LOW-state input current HIGH-state input current OFF-state output current latch-up current pull-up VDD(3V3); pull-down VDD(3V3); pull-up/down -(0.5VDD(3V3)) (1.5VDD(3V3)) Vhys IOHS IOLS IDD(act) input voltage output voltage HIGH-state input voltage LOW-state input voltage hysteresis voltage HIGH-state output voltage LOW-state output voltage HIGH-state output current LOW-state output current HIGH-state short-circuit output current LOW-state short-circuit output current pull-down current pull-up current active mode supply current VDD(3V3) VDDA [10] VDD(3V3) [10] VDD(1V8) code
[11]
Conditions
1.65
1.95
Unit
Standard port pins, RESET, RTCK
configured provide digital function output active
VDD(3V3)
VDD(3V3)
while(1){}
executed from flash, active peripherals CCLK CCLK (other parameters above) IDD(pd) Power-down mode supply current VDD(1V8) VDD(1V8)
<tbd> <tbd> <tbd> <tbd>
<tbd>
<tbd> <tbd> <tbd> <tbd>
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Table Static characteristics .continued commercial applications, unless otherwise specified. Symbol IBATpd Parameter Conditions Unit Power-down mode battery clock supply current [12] (from RTXC pins), VDD(1V8) VBAT VDD(1V8) VBAT IBATact active mode battery supply current [12] CCLK MHz, PCLK 17.5 MHz, PCLK enabled RTCK, clock (from RTXC pins), VDD(1V8) VBAT I2C-bus Vhys pins HIGH-state input voltage LOW-state input voltage hysteresis voltage LOW-state output voltage input leakage current [13] IOLS VDD(3V3) Oscillator pins Vi(XTAL1) Vo(XTAL2) Vi(RTXC1) input voltage XTAL1 output voltage XTAL2 input voltage RTXC1
<tbd> <tbd>
<tbd>
<tbd>
<tbd>
0.7VDD(3V3)
0.3VDD(3V3)
0.5VDD(3V3)
Vo(RTXC2) output voltage RTXC2
Typical ratings guaranteed. values listed room temperature (+25 °C), nominal supply voltages. Core internal rail. External rail. typically fails when VBAT drops below Including voltage outputs 3-state mode. VDD(3V3) supply voltages must present. 3-state outputs into 3-state mode when VDD(3V3) grounded. Accounts voltage drop supply lines. Only allowed short time period.
[10] Minimum condition maximum condition [11] Applies P1.25:16. [12] VBAT. [13] VSS.
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Table static characteristics VDDA unless otherwise specified. frequency MHz. Symbol EL(adj)
Parameter analog input voltage analog input capacitance differential linearity error integral non-linearity offset error gain error absolute error
Conditions
VDDA ±0.5
Unit
Conditions: VSSA VDDA monotonic, there missing codes. differential linearity error (ED) difference between actual step width ideal step width. Figure integral non-linearity (EL(adj)) peak difference between center steps actual ideal transfer curve after appropriate adjustment gain offset errors. Figure offset error (EO) absolute difference between straight line which fits actual curve straight line which fits ideal curve. Figure gain error (EG) relative difference percent between straight line fitting actual transfer curve after removing offset error, straight line which fits ideal transfer curve. Figure absolute error (ET) maximum difference between center steps actual transfer curve non-calibrated ideal transfer curve. Figure
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
offset error 1023
gain error
1022
1021
1020
1019
1018
code
(ideal) 1018 1019 1020 1021 1022 1023 1024
offset error (LSBideal)
VDDA VSSA 1024
002aac046
Example actual transfer curve. ideal transfer curve. Differential linearity error (ED). Integral non-linearity (EL(adj)). Center step actual transfer curve.
conversion characteristics
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Dynamic characteristics
Table Dynamic characteristics commercial applications, industrial applications, VDD(1V8), VDD(3V3) over specified ranges Symbol External clock fosc Tcy(clk) tCHCX tCLCX tCLCH tCHCL tr(o) tf(o) I2C-bus tf(o)
Parameter oscillator frequency clock cycle time clock HIGH time clock time clock rise time clock fall time output rise time output fall time pins (P0.2 P0.3) output fall time
Conditions
Tcy(clk) Tcy(clk)
Unit
Port pins (except P0.2 P0.3)
Parameters valid over operating temperature range unless otherwise specified. Typical ratings guaranteed. values listed room temperature (+25 °C), nominal supply voltages. capacitance from
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Package outline
LQFP48: plastic profile quad flat package; leads; body SOT313-2
detail
index
scale
DIMENSIONS original dimensions) UNIT max. 0.20 0.05 1.45 1.35 0.25 0.27 0.17 0.18 0.12 9.15 8.85 9.15 8.85 0.75 0.45 0.12 0.95 0.55 0.95 0.55
Note Plastic metal protrusions 0.25 maximum side included. OUTLINE VERSION SOT313-2 REFERENCES 136E05 JEDEC MS-026 JEITA EUROPEAN PROJECTION
ISSUE DATE 00-01-19 03-02-25
Package outline SOT313-2 (LQFP48)
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
PLCC44: plastic leaded chip carrier; leads
SOT187-2
detail
index
scale
DIMENSIONS dimensions derived from original inch dimensions) UNIT D(1) E(1) max. min.
inches 4.57 4.19 0.51 0.25 0.01 3.05 0.12 0.53 0.33 0.81 0.66
1.44 1.02
0.18
0.18
ZD(1) ZE(1) max. max.
2.16 2.16
16.66 16.66 16.00 16.00 17.65 17.65 1.22 1.27 16.51 16.51 14.99 14.99 17.40 17.40 1.07 0.63 0.59 0.63 0.59
0.180 0.02 0.165
0.021 0.032 0.656 0.656 0.05 0.013 0.026 0.650 0.650
0.695 0.695 0.048 0.057 0.007 0.007 0.004 0.085 0.085 0.685 0.685 0.042 0.040
Note Plastic metal protrusions 0.25 (0.01 inch) maximum side included. OUTLINE VERSION SOT187-2 REFERENCES 112E10 JEDEC MS-018 JEITA EDR-7319 EUROPEAN PROJECTION
ISSUE DATE 99-12-27 01-11-14
Package outline SOT187-2 (PLCC44)
LPC2101_02_03_1 Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Abbreviations
Table Acronym FIFO GPIO SRAM UART Acronym list Description Analog-to-Digital Converter Advanced Peripheral Debug Communications Channel Digital Signal Processor First First Fast Interrupt Request General Purpose Input/Output In-Application Programming Interrupt Request In-System Programming Phase-Locked Loop Pulse Width Modulator Serial Peripheral Interface Static Random Access Memory Serial Synchronous Port Universal Asynchronous Receiver/Transmitter Vectored Interrupt Controller
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Revision history
Table Revision history Release date 20060118 Data sheet status Preliminary data sheet Change notice Doc. number Supersedes Document LPC2101_2102_2103_1
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Data sheet status
Level Data sheet status Objective data Preliminary data Product status Development Qualification Definition This data sheet contains data from objective specification product development. Philips Semiconductors reserves right change specification manner without notice. This data sheet contains data from preliminary specification. Supplementary data will published later date. Philips Semiconductors reserves right change specification without notice, order improve design supply best possible product. This data sheet contains data from product specification. Philips Semiconductors reserves right make changes time order improve design, manufacturing supply. Relevant changes will communicated Customer Product/Process Change Notification (CPCN).
Product data
Production
Please consult most recently issued data sheet before initiating completing design. product status device(s) described this data sheet have changed since this data sheet published. latest information available Internet data sheets describing multiple type numbers, highest-level product status determines data sheet status.
Definitions
Short-form specification data short-form specification extracted from full data sheet with same type number title. detailed information relevant data sheet data handbook. Limiting values definition Limiting values given accordance with Absolute Maximum Rating System (IEC 60134). Stress above more limiting values cause permanent damage device. These stress ratings only operation device these other conditions above those given Characteristics sections specification implied. Exposure limiting values extended periods affect device reliability. Application information Applications that described herein these products illustrative purposes only. Philips Semiconductors makes representation warranty that such applications will suitable specified without further testing modification.
customers using selling these products such applications their risk agree fully indemnify Philips Semiconductors damages resulting from such application. Right make changes Philips Semiconductors reserves right make changes products including circuits, standard cells, and/or software described contained herein order improve design and/or performance. When product full production (status `Production'), relevant changes will communicated Customer Product/Process Change Notification (CPCN). Philips Semiconductors assumes responsibility liability these products, conveys license title under patent, copyright, mask work right these products, makes representations warranties that these products free from patent, copyright, mask work right infringement, unless otherwise specified.
Trademarks
Notice referenced brands, product names, service names trademarks property their respective owners. I2C-bus logo trademark Koninklijke Philips Electronics N.V.
Disclaimers
Life support These products designed life support appliances, devices, systems where malfunction these products reasonably expected result personal injury. Philips Semiconductors
Contact information
additional information, please visit: sales office addresses, send email
LPC2101_02_03_1
Koninklijke Philips Electronics N.V. 2006. rights reserved.
Preliminary data sheet
Rev. January 2006
Philips Semiconductors
LPC2101/2102/2103
Single-chip 16-bit/32-bit microcontrollers
Contents
6.5.1 6.7.1 6.8.1 6.9.1 6.10 6.10.1 6.11 6.11.1 6.12 6.12.1 6.13 6.13.1 6.14 6.14.1 6.15 6.15.1 6.16 6.16.1 6.17 6.17.1 6.17.2 6.17.3 6.17.4 6.17.5 6.17.6 6.17.7 General description Features features Ordering information Ordering options Block diagram Pinning information Pinning description Functional description Architectural overview. On-chip flash program memory On-chip static RAM. Memory map. Interrupt controller Interrupt sources. connect block Fast general purpose parallel Features 10-bit converter Features UARTs Features I2C-bus serial controllers. Features serial controller. Features serial controller Features General purpose 32-bit timers/external event counters Features General purpose 16-bit timers/external event counters Features Watchdog timer. Features Real-time clock Features System control Crystal oscillator Reset wake-up timer Code security External interrupt inputs Memory mapping control Power control 6.17.8 6.18 6.18.1 6.18.2 Emulation debugging. EmbeddedICE RealMonitor Limiting values Static characteristics Dynamic characteristics Package outline Abbreviations Revision history Data sheet status. Definitions Disclaimers Trademarks Contact information
Koninklijke Philips Electronics N.V. 2006
rights reserved. Reproduction whole part prohibited without prior written consent copyright owner. information presented this document does form part quotation contract, believed accurate reliable changed without notice. liability will accepted publisher consequence use. Publication thereof does convey imply license under patent- other industrial intellectual property rights. Date release: January 2006 Document number: LPC2101_02_03_1
Published Netherlands

Single-chip 16-bit/32-bit microcontrollers; kB/16 kB/32 flash with ISP

Top Searches for this datasheet

Other recent searches