Document Title 128K VOLTAGE CMOS SRAM Revision History 128K VOLTA

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Document Title 128K VOLTAGE CMOS SRAM Revision History 128K VOLTA

Datasheet Thumbnail

Top Searches for this datasheet

LP62E16128A-I Series
Document Title 128K VOLTAGE CMOS SRAM Revision History
128K VOLTAGE CMOS SRAM
History
Initial issue
Issue Date
December 2003
Remark
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Features
Operating voltage: 1.65V 2.2V Access times: (max.) Current: Very power version: Operating: 25mA (max.) Standby: 10µA (max.) Full static operation, clock refreshing required inputs outputs directly TTL-compatible Common using three-state output Data retention voltage: 1.2V (min.) Available 44-pin TSOP 48-ball 8mm) packages
128K VOLTAGE CMOS SRAM
General Description
LP62E16128A-I operating current 2,097,152bit static random access memory organized 131,072 words bits operates power voltage from 1.65V 2.2V. built using AMIC's high performance CMOS process. Inputs three-state outputs compatible allow direct interfacing with common system structures. chip enable input provided POWER-DOWN, device enable. byte enable inputs output enable input included easy interfacing. Data retention guaranteed power supply voltage 1.2V.
Configurations
TSOP (Chip Size Package) 48-pin View
I/O1 I/O2 I/O3 I/O4 I/O5 I/O6 I/O7 I/O8
I/O16 I/O15 I/O14 I/O13 I/O12 I/O11 I/O10 I/O9
I/O9 I/O10 I/O15 I/O16
I/O11 I/O12 I/O13 I/O14
I/O2 I/O4 I/O5 I/O6
I/O1 I/O3 I/O7 I/O8
LP62E16128AV-T
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Block Diagram
1024 2048 DECODER MEMORY ARRAY
I/O1 COLUMN INPUT DATA CIRCUIT
I/O9
INPUT DATA CIRCUIT
I/O8
I/O16
CONTROL CIRCUIT
Descriptions TSOP
Symbol Description Address Inputs
I/O1 I/O16
Chip Enable Input
Data Inputs/Outputs Write Enable Input Lower Byte Enable Input (I/O1 I/O8) Higher Byte Enable Input (I/O9 I/O16) Output Enable Input Power Ground Connection
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Description
Symbol Description Symbol Description
Address Inputs
Higher Byte Enable Input (I/O9 I/O16) Output Enable Power Supply Ground Connection
I/O1 I/O16
Chip Enable Data Input/Output Write Enable Input Lower Byte Enable Input (I/O1 I/O8)
Recommended Operating Conditions
-40°C 85°C)
Symbol Parameter Min. Typ. Max. Unit
Supply Voltage Ground Input High Voltage Input Voltage Output Load Output Load
1.65 -0.2
+0.4
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Absolute Maximum Ratings*
-0.5V +3.0V IN/OUT Volt GND.-0.5V 0.5V Operating Temperature, Topr -40°C +85°C Storage Temperature, Tstg. -55°C +125°C Power Dissipation, .0.7W
*Comments
Stresses above those listed under "Absolute Maximum Ratings" cause permanent damage this device. These stress ratings only. Functional operation this device these other conditions above those indicated operational sections this specification implied intended. Exposure absolute maximum rating conditions extended periods affect device reliability.
Electrical Characteristics -40°C 85°C, 1.65V 2.2V,
Symbol Parameter LP62E16128A-70LLI Min. Max. Unit Conditions
Input Leakage Current
VI/O II/O Min. Cycle, Duty 100% VIL, II/O
Output Leakage Current
ICC1
Active Power Supply Current
Dynamic Operating Current ICC2
VIL, VCC, 1MHz, II/O 0.2V, -0.1
ISB1
Standby Power Output Voltage Output High Voltage
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Truth Table
Note: I/O1 I/O8 Mode selected High-Z Read Read High Write Write Write/Hi High High I/O9 I/O16 Mode selected High-Z Read High Read Write Write/Hi Write High High Current ISB1, ISB1, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2, ICC1, ICC2,
Capacitance 25°C, 1.0MHz)
Symbol CIN* CI/O* Parameter Input Capacitance Input/Output Capacitance Min. Max. Unit Conditions VI/O
These parameters sampled 100% tested.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Characteristics -40°C +85°C, 1.65V 2.2V)
Symbol Read Cycle tACE tCLZ tBLZ tOLZ tCHZ tBHZ tOHZ Write Cycle tWHZ Write Cycle Time Chip Enable Write Byte Enable Write Address Setup Time Address Valid Write Write Pulse Width Write Recovery Time Write Output High Data Write Time Overlap Data Hold from Write Time Output Active from Write Read Cycle Time Address Access Time Chip Enable Access Time Byte Enable Access Time Output Enable Output Valid Chip Enable Output Byte Enable Outupt Output Enable Output Chip Disable Output High Byte Disable Output High Output Disable Output High Output Hold from Address Change Parameter LP62E16128A-70LLI Min. Max. Unit
Note: tCHZ, tBHZ tOHZ tWHZ defined time which outputs achieve open circuit condition referred output voltage levels.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Timing Waveforms
Read Cycle 1(1,
Address
DOUT
Read Cycle 2(1,
Address
tACE tCLZ5
tCHZ5
tBLZ5
tBHZ5
tOHZ5
tOLZ5 DOUT
Notes:
high Read Cycle. Device continuously enabled and, VIL. Address valid prior coincident with and, transition low. VIL. Transition measured ±500mV from steady state. This parameter sampled 100% tested.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Timing Waveforms (continued)
Write Cycle (Write Enable Controlled)
Address tWR3
tAS1
tWP2
DATA tWHZ4
DATA
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Timing Waveforms (continued)
Write Cycle (Chip Enable Controlled)
Address tAS1 tCW2 tWR3
DATA tWHZ4
DATA
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Timing Waveforms (continued)
Write Cycle (Byte Enable Controlled)
Address
tWR3
tAS1
tBW2
DATA tWHZ4 DATA
Notes: measured from address valid beginning Write. Write occurs during overlap (tWP, tBW) measured from earliest going high Write cycle. level high low. Transition measured ±500mV from steady state. This parameter sampled 100% tested.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Test Conditions
Input Pulse Levels Input Rise Fall Time Input Output Timing Reference Levels Output Load 0.2V 0.2V 0.9V Figures
30pF
Including scope jig.
Including scope jig.
Figure Output Load
Figure Output Load tCLZ, tOLZ, tCHZ, tOHZ, tWHZ,
Data Retention Characteristics -40°C 85°C)
Symbol Parameter Data Retention Min. Max. Unit Conditions 0.2V 1.2V, 0.2V
ICCDR
Data Retention Current
tCDR
Chip Disable Data Retention Time Operation Recovery Time Rising Time from Data Retention Voltage Operating Voltage ICCDR: max.
Retention Waveform
LP62E16128A-70LLI
40°C
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Data Retention Waveform
DATA RETENTION MODE 1.8V tCDR 1.2V 0.2V 1.8V
Ordering Information
Part Access Time (ns) Operating Current Max. (mA) LP62E16128AU-70LLI Standby Current Max. (µA) Package
LP62E16128AV-70LLI
TSOP
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Package Information TSOP TYPE Outline Dimensions
unit: inches/mm
0.254
Symbol
Dimension inch Min. 0.002 0.037 0.010 0.721 0.396 0.455 0.016 Nom. 0.039 0.014 0.006 0.725 0.400 0.031 0.463 0.020 0.031 Max. 0.047 0.041 0.018 0.729 0.404 0.471 0.024 0.036 0.004
Dimension Min. 0.05 0.95 0.25 18.31 10.06 11.56 0.40 Nom. 1.00 0.35 0.15 18.41 10.16 0.80 11.76 0.50 0.80 Max. 1.20 1.05 0.45 18.51 10.26 11.96 0.60 0.93 0.10
Notes: Dimension include interlead flash. Dimension does include dambar protrusion/intrusion. Dimension includes flash.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.
LP62E16128A-I Series
Package Information 48LD Outline Dimensions
(48TFBGA)
VIEW BOTTOM VIEW Ball#A1 CORNER 0.10 0.25 Ball*A1 CORNER (48X)
unit:
0.10 0.20(4X)
SIDE VIEW 0.25
(0.36)
SEATING PLANE
Symbol
Dimensions MIN. 1.00 0.20 0.48 5.90 7.90 -0.30 NOM. 1.10 0.25 0.53 6.00 8.00 3.75 5.25 0.75 0.35 MAX. 1.20 0.30 0.58 6.10 8.10 -0.40
Note: BALL DIAMETER, BALL PITCH, STAND-OFF PACKAGE THICKNESS DIFFERENT FROM JEDEC SPEC MO192 (LOW PROFILE FAMILY). PRIMARY DATUM SEATING PLANE DEFINED SPHERICAL CROWNS SOLDER BALLS. DIMENSION MEASURED MAXIMUM. THERE SHALL MINIMUM CLEARANCE 0.25mm BETWEEN EDGE SOLDER BALL BODY EDGE.
PRELIMINARY
(December, 2003, Version 0.0)
AMIC Technology, Corp.

Document Title 128K VOLTAGE CMOS SRAM Revision History 128K VOLTA

Top Searches for this datasheet

Other recent searches