Preliminary Provisional 2-CHANNEL STEP-UP CONTROLLERS Featur

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

Preliminary Provisional 2-CHANNEL STEP-UP CONTROLLERS Featur

Datasheet Thumbnail

Top Searches for this datasheet

AAT1106
Preliminary Provisional
2-CHANNEL STEP-UP CONTROLLERS
Features Complete Power Control Circuitry Under-voltage Lockout Protection Totem pole Output Output Short Circuit Protection Dead Time Control0 100% Wide Operating Frequency 10kHz 800kHz Shut Down Control Power Good Protection General Description AAT1106 series provides integrated two-channel pulse-width-modulation (PWM) solution power supply DC-DC system, this device offers systems engineer flexibility tailor power supply circuitry specific application. Each channel contains error amplifier, comparator, dead-time control output driver. under-voltage protection, oscillator, short circuit protection voltage reference circuit common channels. AAT1106 contains boost (step-up) exclusive circuit. Dead-time control (DTC) provide 100% dead time resistive divider network. Soft start implemented paralleling resistor with capacitor. dead time control inputs assigned Ch-1 Ch-2 individually, dead time control inputs used control operation. With minimum number external components, AAT1106 series offers simple cost effective solution.
Configuration
VIEW
SHDN INV1 DTC1 OUT1 Vref PRDB INV2 DTC2 OUT2
(TSSOP-16 PACKAGE)
*Spec subject change without notice this document.
Advanced Analog Technology, Inc.
January 2004
AAT1106
Description Name SHDN INV1 DTC1 OUT1 OUT2 DTC2 INV2 PRDB Vref External timing capacitance External timing resistance Shut down input pininternal pull Negative input error amplifier Output error amplifier Output dead time soft start setting Output Ground Power supply Output Output dead time soft start setting Output error amplifier Negative input error amplifier Power good output Timer latch setting Reference voltage (2.505V) output Description
Advanced Analog Technology, Inc.
January 2004
AAT1106
Absolute Maximum Ratings CHARACTERISTICS Supply voltage Input voltage (IN-, DTC, SHDN) Output voltage SYMBOL VALUE UNIT
+0.3 -120/+120
Output current Operating free-air temperature range Storage temperature range Power dissipation
Recommended Operating Conditions
Tope Tstg
Supply voltage, Input voltage, INV1, INV2 Output voltage capacitor resistor (Note Oscillator frequency Output current, Iout1, Iout2 Operating free-air temperature
Symbol
15000
Unit
Tope
+50/-50
Advanced Analog Technology, Inc.
January 2004
AAT1106
Electrical Characteristics, 5.0V (Unless Otherwise Specified) (See Note Oscillator
Parameter Test Condition
Frequency Frequency change with
220pF, 4.0V 6.0V, 220pF,
Unit
Under-voltage Protection
Parameter Test Condition Unit
Upper threshold voltage Lower threshold voltage Hysteresis VUPH VUPL
Short Circuit Protection Control
Parameter
VUPH VUPL VHYS
2.23
2.53 0.37
2.83
Test Condition
Unit
Input threshold voltage Short-circuit detect threshold voltage terminal source current Standy Voltage Latch Voltage
Ch-1,
1.48 -1.5
1.64 -2.5
2.65 -3.5
VSTB
Shun Down ControlInternal pull
Parameter Test Condition Unit
Shut down enable voltage Shut down release voltage
VsdL VsdH
Note1 Typical values parameters specified
Advanced Analog Technology, Inc.
January 2004
AAT1106
Electrical Characteristics, 5.0V (Unless Otherwise Specified) (See Note (continued) Reference Voltage
Parameter Test Conditions
Unit
Internal reference Voltage Reference voltage Input voltage regulation Output regulation
Vrefi VREF
-1mA 1.220 -1mA -1mA 4.0V 6.0V -0.1mA -1mA
1.233 1.246
2.430 2.505 2.580
(Error Amplifier)
Parameter Test Condition
Input offset voltage Input bias current Input voltage range Open-loop voltage amplification Output voltage swing Output sink current Output source current
Ch-1,2, AV=1 Ch-1,2 Ch-1,2 FB=1.25V FB=1.25V
Unit
±100
Common-mode rejection ratio CMRR
Advanced Analog Technology, Inc.
January 2004
AAT1106
Electrical Characteristics, 5.0V (Unless Otherwise Specified) (See Note (continued) Dead Time Control Parameter Test Condition Unit Input bias current VDTC
Input threshold voltage (DTC) Latch input voltage Latch mode source current
Output Stage
Parameter
Duty 10kHz Vd100 Duty 100%,
10kHz 100µA
1.38 1.87
1.48 1.97
1.58 2.07
DTC1,2=2.0V
Test Condition
High-level output voltage Low-level output voltage Rise time Fail time Leakage current
Operating Current
Parameter
Trise Tfail Ipeak
IO=-50mA IO=+50mA CL=1000pF CL=1000pF =6.0V
Unit
Test Condition
Supply current
DD-OFF DD-ON
Output "OFF" state
Unit
Advanced Analog Technology, Inc.
January 2004
AAT1106
Function Block Diagram
INV1
Err-Amp 1.233V Vrefi
Scpcomp
OUT1
Vrefi 1.233V
INV2 DTC1
Err-Amp
OUT2
DTC2
LATCH LATCH
UVLO
PRDB
Vref
SHDN SHUT_DOWN CONTROL
VREF
Vref
Advanced Analog Technology, Inc.
January 2004
AAT1106
Application Circuit
VDDP
PRDB OUT1
INV1
VDDP
AAT1106
INV2
OUT2 SHDN SHDN VREF DTC1 DTC2
Advanced Analog Technology, Inc.
January 2004
AAT1106
Application Circuit
option circuit power good protection
option circuit charge pump circuit
VDDP PRDB
PRDB OUT1
INV1
VDDP
AAT1106
INV2
OUT2
SHDN SHDN VREF DTC1 DTC2
PRDB
option circuit discharge
Advanced Analog Technology, Inc.
January 2004
AAT1106
Boost Step-upTiming Chart
2.4V 1.97V
1.48V
PWMOUTPUT
OUTPUT
1.64V
SCPCOMP
2.53V
Lockout free
PRDB
Advanced Analog Technology, Inc.
January 2004
AAT1106
Package Dimension (Unit: Mil)
Advanced Analog Technology, Inc.
January 2004

Preliminary Provisional 2-CHANNEL STEP-UP CONTROLLERS Featur

Top Searches for this datasheet

Other recent searches