DOCUMENT RB000000 REVISION PAGE Scope This specification applies

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

DOCUMENT RB000000 REVISION PAGE Scope This specification applies

Datasheet Thumbnail

Top Searches for this datasheet

0603 Series Thin Film Chip Resistor
DOCUMENT RB000000 REVISION PAGE
Scope This specification applies 0.8mm 1.6mm (0603) size, fixed metal chip resistors rectangular type electronic equipment. Type Designation RR0816 Where
Series Tolerance ±25ppm/ ±50ppm/ ±100ppm/ Nominal resistance value example -Three digits number (E-24 Series) Four digits number (E-96 Series) 11R3 11.3 1131 =1.13k Resistance tolerance 0.1% 0.5%
Electrical Specifications Power Rating* Resistance Values Resistance Tolerance Resistance Range T.C.R. (Temperature Coefficient Resistance) Operating Temperature Range Max. Operating Voltage** Note: *Package Power Temperature Derating Curve
LOAD(%)
1/10 E-24 series E-96 series 0.5%(D) 1091 50ppm 0.1%(B) 0.5%(D) 10033k 25ppm 36k360k 25ppm ±100ppm
DOCUMENT RB000000 REVISION PAGE
Note: **Resistors shall have rated AC(rms.) continuous operating voltage corresponding power rating, calculated from following formula Where Rated voltage Rated power Nominal resistance voltage obtained exceeds maximum operating voltage, this maximum voltage shall rated voltage. Outline dimensions Code Letter Dimension Unit
Marking Resistance E-24 Series Example 3.9k39 102392 Resistance E-96 Series code value code value code value
DOCUMENT RB000000 REVISION PAGE
rated resistance shall marked protecting coat with three digits number.
code
value
This table shows first digits three-digits E-96 series part marking scheme. third character letter multiplier: S=10-2 Example 10.2k102 10202C R=10-1 A=100 H=101 C=102 D=103 E=104 F=105
Life Tests Electrical Item Specification Requirement
DOCUMENT RB000000 REVISION PAGE
Test Method Applied voltage rated voltage maximum operating voltage which ever less Test time seconds
Short Time Overload (0.5%+ 0.05) Without damage flashover, spark, arcing, burning breakdown
Insulation Resistance Over Overcoat layer face Over 1,000 Substrate side face Voltage Proof (0.5%+ 0.05) Without damage flashover, spark, arcing, burning breakdown
Setup figure Test voltage Test time seconds Setup figure Test voltage VAC(rms.) Test time seconds
Pressure (Metal) Measurement Point (R=0.5 Substrate Over coat Film Substrate Side
Insulation Plate Spring Sample Electrode Voltage Supply Metal Block Measurement Point
Figure Measurement Setup
Mechanical Item Solderability Specification Requirement
DOCUMENT RB000000 REVISION PAGE
Test Method
surface terminal immersed shall Solder bath After immersing flux, minimum covered with coating solder molten solder bath seconds Pre-heat 100~110 seconds Immersed solder bath seconds Measuring resistance hour after test Vibration frequency 10Hz 55Hz to10Hz seconds period Vibration time period cycled hours each mutual perpendicular directions Amplitude 1.5mm Peak value 490N Duration pulse 11ms times each positive negative direction mutual perpendicular directions Bending value seconds Solvent Trichloroethane Isopropyl alcohol Immersed solvent room temperature seconds
Resistance Solder (0.5%+ 0.05) Heat Without distinct deformation appearance
Vibration
(0.5%+ 0.05) Without mechanical damage such break
Shock
(0.25%+ 0.05) Without mechanical damage such break
Bending Test
(0.5%+ 0.05) Without mechanical damage such break Marking should legible Without mechanical distinct damage appearance
Solvent Resistance
Endurance Item Rapid change Temperature Specification Requirement
DOCUMENT RB000000 REVISION PAGE
Test Method
Repeat cycle follow (0.5%+ 0.05) (-55 3,30minutes) (Room Without distinct damage appearance temperature, minutes) (+125 2,30minutes) (Room temperature, minutes) Measuring resistance hour after test Environment condition 2,90~95% Applied Voltage rated voltage Test period: (1.5 hour (0.5 hour OFF) cycled total 1,000 hours Measuring resistance hour after test Test temperature (1.0%+ 0.05) Without distinct damage appearance Applied Voltage rated voltage Test period: (1.5 hour (0.5 hour OFF) cycled total 1,000 hours Measuring resistance hour after test Sto± temperature (1.0%+ 0.05) total Without distinct damage appearance 1,000 hours Measuring resistance hour after test Store temperature (1.0%+ 0.05) +125 total Without distinct damage appearance 1,000 hours Measuring resistance hour after test
Moisture with Load (1.0%+ 0.05) Without distinct damage appearance Marking should legible
Load Life
Temperature Store
High Temperature Store
Recommend Land Pattern Dimensions
DOCUMENT RB000000 REVISION PAGE
0.6~1.0 Unit
Packaging Dimensions 8-1-1 Tape packaging dimensions
0.05
DOCUMENT RB000000 REVISION PAGE
0.05
Sprocket hole
1.75
0.05
Chip
0.65
P(PITCH)
Carries cavity
Unit
8-1-2 Reel dimensions
60-0
Unit
Peel force cover tape peel speed shall about mm/minute peel force cover tape shall between
Cover Tape
DOCUMENT RB000000 REVISION PAGE
0.1N~0.7N 165~180°
Numbers taping 5,000 pieces/reel Label marking following items shall marked production shipping Label reel. 8-4-1 Production Label Part Description Quantity Taping 8-4-2 Shipping Label *Customer's name *Customer's part Manufacturer's part Manufacturer's name Manufacturer's country *Note Item listed request Note Manufactured joint company. Susumu Co., Ltd.
DOCUMENT RB000000 REVISION PAGE
Care note Care note storage Chip resistor shall stored room where temperature humidity must controlled. (temperature humidity However, humidity keep low, possible. Chip resistor shall stored direct sunshine doesn't Chip resistor shall stored with moisture, dust, material that will make solderability inferior, harmful (Chloridation hydrogen, sulfurous acid gas, sulfuration hydrogen) Care note operating handling necessary protect edge protection coat resistors from mechanical stress. Handle with care when printing circuit board (PCB) divided fixed support body, because bending printing circuit board (PCB) mounting will make mechanical stress resistors. Resistors shall used with rated range shown specification. Especially, voltage more than specified value will loaded resistor, there case will make damage machine because temperature rise depending generating heat, increase resistance value breaks. case that resistor loaded rated voltage, necessary confirms temperature resistor reduce load power according load reduction curve, because temperature rise resistor depends influence heat from mounting density neighboring element. Observe Limiting element voltage maximum overload voltage specified each specification there possibility that large voltage (pulse voltage, shock voltage) charge resistor, necessary that operating condition shall before use.

DOCUMENT RB000000 REVISION PAGE Scope This specification applies

Top Searches for this datasheet

Other recent searches