GP1FB201RK Thin type (4.2mm) fiber optic receiver Compact (adopti

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

GP1FB201RK Thin type (4.2mm) fiber optic receiver Compact (adopti

Datasheet Thumbnail

Top Searches for this datasheet

GP1FB201RK
GP1FB201RK
Thin type (4.2mm) fiber optic receiver Compact (adoption small jack mini plug) C6560 Both optical electrical signal distinguished received voltage operation (VCC 3.0V) High speed data transmission (Signal transmission speed MAX. 8Mbps (NRZ signal))
Voltage Operation Thin Type Optical Mini-jack Digital Audio Equipment
Outline Dimensions
(Unit
Jack terminal Jack body Device terminal
12.2
Applications
players Portable players (Optic receiver part)
±0.0
2.1±0.2
View
+0.1 4.2-0.2
-0.1
Absolute Maximum Ratings (Photoelectric conversion element)
Parameter Supply voltage Operating temperature Storage temperature Soldering temperature Output current
times less) Source current Sink current
2-1.4 0.25
(Ta=25°C) Unit
4±0.2 8.5±0.2 2±0.1 (R0.2) 7.5±0.2 17+0.2 -0.1 View 12.2 Internal equivalent circuit
Symbol Topr Tstg Tsol
Rating -0.5 +7.0
Absolute Maximum Ratings(Jack)
Parameter Total power dissipation Operating temperature Storage temperature Soldering temperature *2Isolation voltage
times less) 1min
Symbol Rating Ptot D.C. 12V, Topr Tstg Tsol Viso A.C. 500Vrms
Unit
3-0.4
OPIC Light Detector Jack terminal configuration
Unspecified tolerance ±0.3mm Reference dimensions When pattern circuit make contact with cause short-circuited each terminal.
portion,
"OPIC" (Optical trademark SHARP Corporation. OPIC consists light-detecting element signal-processing circuit integrated onto single chip.
Notice
absence confirmation device specification sheets, SHARP takes responsibility defects that occur equipment using SHARP devices shown catalogs, data books, etc. Contact SHARP order obtain latest device specification sheets before using SHARP device. Internet Internet address Electronic Components Group http://www.sharp.co.jp/ecg/
+0.3 0.25-0.1
GP1FB201RK Recommended Operating Conditions
Parameter Symbol MIN. MAX. TYP. Unit Operating supply voltage Operating transfer rate Mbps Receiver input optical power level -24.0 -14.5
Electro-optical Characteristics
Parameter Peak sensitivity wavelength Dissipation current High level output voltage level output voltage Rise time Fall time High delay time High delay time Pulse width distortion Jitter Symbol tpLH tpHL Conditions Refer Fig.1 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.3, -14.5dBm Refer Fig.3, -24dBm MIN. TYP.
(Ta=25°C, Vcc=2.5V) MAX. Unit
Mechanical Electrical Characteristics(Jack)
Parameter Insertion force, withdrawal force Contact resistance Isolation resistance Symbol Rcon Riso Conditions D.C. 500V, 1min. MIN. TYP. MAX. Unit
Note) This jack designed applicable compact single head plug (JIS C6560). Measuring method insertion force withdrawal force. Insertion withdrawal force shall measured after inserting withdrawing times using C6560 standard plug test. Measuring method contact resistance. measures 100mA less 1000Hz condition inserting C6560 standard plug test which movable contact terminal contact point described.
Fig.1 Dissipation Current
Supply voltage Fiber coupling light output Standard transmitter input signal Input conditions VCC=2.5±0.05V PC=-14.5dBm 6Mbps NRZ, Duty 3Mbps biphase mark PRBS signal
Fiber optic cable Standard transmitter Ammeter GP1FB201RK Unit measured Vout
Measuring method Measured ammeter average amperage)
2.5V Input
GP1FB201RK Fig.2 Measuring Method Output Voltage Pulse Response
Fiber optic cable Standard transmitter Input 2.5V GP1FB201RK Unit measured Vout
6Mbps NRZ, Duty
Tektronix 7834 7934 type Oscilloscope
Test item
Test item High pulse delay time High pulse delay time Rise time Fall time Pulse width distortion tw=tpHL-tpLH High level output voltage level output voltage
Notes
Symbol tpLH tpHL
Standard transmitter Input signal (CH1)
GP1FB201RK Output signal (CH2)
VCC=2.5±0.05V (State operating) fiber coupling light output -14.5dBm/-24.0dBm. probe oscilloscope must more than less than 10pF. output (H/L level) GP1FB201RK fixed constantly when receives modulating light (including light, input light) less than 0.1Mbps.
tpLH
tpHL
GP1FB201RK Fig.3 Measuring Method Jitter
Fiber optic cable Standard transmitter 2.5V GP1FB201RK Unit measured Vout
Oscilloscope Input Tektronix7834 7934 type Trigger Storage mode Sweep AUTO/NORM
Input signal 3Mbps biphase PRBS signal
Test item
Test item Symbol Jitter Jitter Test condition trigger rise input signal measure jitter rise output trigger fall input signal measure jitter fall output
Input signal
Notes fiber coupling light output -14.5dBm/-24.0dBm. ocsilloscope storage mode write time shall seconds. allow waveform distorted increasing brightness much. VCC=2.5±0.05V (State operating) probe oscilloscope must more than less than 10pF.
GP1FB201RK output
Application Circuits
NOTICE
qThe circuit application examples this publication provided explain representative applications SHARP devices intended guarantee circuit design license intellectual property rights. SHARP takes responsibility problems related intellectual property right third party resulting from SHARP's devices. qContact SHARP order obtain latest device specification sheets before using SHARP device. SHARP reserves right make changes specifications, characteristics, data, materials, structure, other contents described herein time without notice order improve design reliability. Manufacturing locations also subject change without notice. qObserve following points when using devices this publication. SHARP takes responsibility damage caused improper devices which does meet conditions absolute maximum ratings used specified relevant specification sheet meet following conditions: devices this publication designed general electronic equipment designs such Personal computers Office automation equipment Telecommunication equipment [terminal] Test measurement equipment Industrial control Audio visual equipment Consumer electronics (ii)Measures such fail-safe function redundant design should taken ensure reliability safety when SHARP devices used connection with equipment that requires higher reliability such Transportation control safety equipment (i.e., aircraft, trains, automobiles, etc.) Traffic signals leakage sensor breakers Alarm equipment Various safety devices, etc. (iii)SHARP devices shall used connection with equipment that requires extremely high level reliability safety such Space applications Telecommunication equipment [trunk lines] Nuclear power control equipment Medical other life support equipment (e.g., scuba). qContact SHARP representative advance when intending SHARP devices "specific" applications other than those recommended SHARP when unclear which category mentioned above controls intended use. SHARP devices listed this publication fall within scope strategic products described Foreign Exchange Foreign Trade Control Japan, necessary obtain approval export such SHARP devices. qThis publication proprietary product SHARP copyrighted, with rights reserved. Under copyright laws, part this publication reproduced transmitted form means, electronic mechanical, purpose, whole part, without express written permission SHARP. Express written permission also required before this publication made third party. qContact consult with SHARP representative there questions about contents this publication.

GP1FB201RK Thin type (4.2mm) fiber optic receiver Compact (adopti

Top Searches for this datasheet

Other recent searches