GP1FD200TK Compact (adoption compact jack mini plug) C6560 Optica

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

GP1FD200TK Compact (adoption compact jack mini plug) C6560 Optica

Datasheet Thumbnail

Top Searches for this datasheet

GP1FD200TK
GP1FD200TK
Compact (adoption compact jack mini plug) C6560 Optical digital signal electric analog signal discriminated transmitted High speed data transmission Signal transmission speed:MAX.8Mbps (NRZ signal) voltage operation Operating Voltage:2.3 2.8V
Voltage Operation Thin Type Optical Mini-jack Digital Audio Equipment
Outline Dimensions
7±0.2 Depression
(Unit
12.2
Applications
4.2±0.1
Depression 8.5±0.2 3.6±0.05 (R0.2) (R0.25)
-0.1
players Portable players
+0.2 -0.1
Absolute Maximum Ratings
Parameter Supply voltage Input voltage Operating temperature Storage temperature Soldering temperature
times less)
(Ta=25°C)
3-0.4
14.425
Symbol Rating Unit -0.5 +7.0 -0.5 +0.5 Topr Tstg Tsol
2-1.2-0.1
C0.15
Terminal thickness
-0.1
0.25 +0.3 -0.1
2-1.4
Absolute Maximum Ratings (Jack)
Parameter Total power dissipation Operating temperature Storage temperature Soldering temperature Isolation voltage
1min
(Ta=25°C) Unit
Symbol Ptot Topr Tstg Tsol Viso (rms)
Rating D.C. 12V, A.C. 500V
Jack terminal Jack body Device terminal
Jack terminal configuration
Internal equivalent circuit Drive
12.2
LED:GaAl Drive IC:Silicone
(Internal connection terminal)
When pattern circuit make contact with cause short-circuited each terminal Unspecified tolerance ±0.3mm Reference dimensions
portion,
"OPIC" (Optical trademark SHARP Corporation. OPIC consists light-detecting element signal-processing circuit integrated onto single chip.
Notice
absence confirmation device specification sheets, SHARP takes responsibility defects that occur equipment using SHARP devices shown catalogs, data books, etc. Contact SHARP order obtain latest device specification sheets before using SHARP device. Internet Internet address Electronic Components Group http://www.sharp.co.jp/ecg/
GP1FD200TK Recommended Operating Conditions
Parameter Operating supply voltage Operating transfer rate Symbol MIN. TYP. MAX. (Ta=25°C) Unit Mbps (Ta=25°C, Vcc=2.5V) TYP. MAX. Unit
Electro-optical Characteristics
Parameter Symbol Conditions
MIN.
Peak emission wavelength Optical power output coupling with fiber High level dissipation current level dissipation current High level input voltage level input voltage LowHigh delay time HighLow delay time Pulse width distortion Jitter
ICCH ICCL tpLH tpHL
Refer Fig.1 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.2 Refer Fig.3 Refer Fig.3 Refer Fig.3 Refer Fig.3
Mechanical Characteristics
Parameter Insertion force, withdrawal force Contact resistance Isolation resistance Symbol Rcon Riso Conditions
D.C.500V, 1min.
MIN.
TYP.
MAX.
Unit
Note) This jack designed applicable compact single head plug (JIS C6560). Measuring method insertion force withdrawal force. Insertion withdrawal force shall measured after inserting withdrawing times using C6560 standard plug test. Measuring method contact resistance. measures 100mA less 000Hz condition inserting C6560 standard plug test which movable contact terminal contact point described.
GP1FD200TK Fig.1 Measuring Method Optical Output Coupling with Fiber
Standard optical fiber cable GP1FD200TK Unit measured optical power meter must calibrated have wavelength sensitivity 660nm (0dB=1mW) Optical power meter (Anritsu) ML93B
Note VCC=2.5V (State operating) bundle standard fiber optic cable, make into loop with diameter D=10cm more (The standard fiber optic cable will specified elsewhere.)
Fig.2 Measuring Method Intput Voltage Supply Current
Standard fiber optic cable GP1FD200TK Unit measured Optical power meter (Anritsu) ML93B optical power meter must calibrated have wavelength sensitivity 660nm (0dB=1mW)
Input conditions judgement method Conditions VIN=1.9V more VIN=0.7V less Judgement method -21PC-15dBm, ICC=10mA less PC-36dBm, ICC=1.0mA less
Note VCC=2.5V (State operating)
GP1FD200TK Fig.3 Measuring Method Pulse Response Jitter
Standard fiber optic cable GP1FD200TK Unit measured Input Input signal 3Mbps biphase mark PRBS signal Oscilloscope Tektronix 7834 7934 type Trigger;CH1 Storage mode Standard receiver Output signal
Input signal tPLH tPHL
Standard receiver output
Parameter
Symbol
Conditions
LowHigh delay time HighLow delay time Pulse width distortion LowHigh jitter HighLow jitter
tpLH tpHL
Refer above mentioned prescription Refer above mentioned prescription tw=tpHL-tpHL trigger rise input signal measure jitter rise output trigger fall input signal measure jitter fall output
Notes waveform write time shall allow waveform distorted increasing brightness much VCC=2.5V (State operating) probe oscilloscope must more than less than 10pF
Application Circuits
NOTICE
qThe circuit application examples this publication provided explain representative applications SHARP devices intended guarantee circuit design license intellectual property rights. SHARP takes responsibility problems related intellectual property right third party resulting from SHARP's devices. qContact SHARP order obtain latest device specification sheets before using SHARP device. SHARP reserves right make changes specifications, characteristics, data, materials, structure, other contents described herein time without notice order improve design reliability. Manufacturing locations also subject change without notice. qObserve following points when using devices this publication. SHARP takes responsibility damage caused improper devices which does meet conditions absolute maximum ratings used specified relevant specification sheet meet following conditions: devices this publication designed general electronic equipment designs such Personal computers Office automation equipment Telecommunication equipment [terminal] Test measurement equipment Industrial control Audio visual equipment Consumer electronics (ii)Measures such fail-safe function redundant design should taken ensure reliability safety when SHARP devices used connection with equipment that requires higher reliability such Transportation control safety equipment (i.e., aircraft, trains, automobiles, etc.) Traffic signals leakage sensor breakers Alarm equipment Various safety devices, etc. (iii)SHARP devices shall used connection with equipment that requires extremely high level reliability safety such Space applications Telecommunication equipment [trunk lines] Nuclear power control equipment Medical other life support equipment (e.g., scuba). qContact SHARP representative advance when intending SHARP devices "specific" applications other than those recommended SHARP when unclear which category mentioned above controls intended use. SHARP devices listed this publication fall within scope strategic products described Foreign Exchange Foreign Trade Control Japan, necessary obtain approval export such SHARP devices. qThis publication proprietary product SHARP copyrighted, with rights reserved. Under copyright laws, part this publication reproduced transmitted form means, electronic mechanical, purpose, whole part, without express written permission SHARP. Express written permission also required before this publication made third party. qContact consult with SHARP representative there questions about contents this publication.

GP1FD200TK Compact (adoption compact jack mini plug) C6560 Optica

Top Searches for this datasheet

Other recent searches