GP1F562T/GP1F553T/GP1FB200TK Compact (adoption small jack mini pl

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

GP1F562T/GP1F553T/GP1FB200TK Compact (adoption small jack mini pl

Datasheet Thumbnail

Top Searches for this datasheet

GP1F562T/GP1F553T/GP1FB200TK
GP1F562T/GP1F553T/GP1FB200TK
Compact (adoption small jack mini plug C656) Thin type (4.4mm) transmitter unit Both optical electrical signal distinguished transmitted High speed data transmission Signal transmission speed MAX. 8Mbps (NRZ signal) voltage operation GP1F562T 3.6V GP1F553T 4.75 5.25V GP1FB200TK 2.8V dissipation current Minimum input optical power level approved EIAJ stan-dard (CP-1201)
Thin Type Optical Mini-jack Transmitter Type Digital Audio Equipment
Outline Dimensions
10±0.2
(Unit
3.6±0.05 2.5±0.1
4.4-0.1
10.8 (10.6)
18+0.2 -0.1
5.5-0.1
2.2±0.1
2.54 10.3 1.85
2.54
2-0.5-0.1 2-C0.15
+0.3 0.25-0.1
7-1±0.1
13.925 11.5
Absolute Maximum Ratings (Photoelectric conversion element)
(Ta=25°C)
4.25
Parameter Symbol Rating Unit -0.5 +7.0 Supply voltage -0.5 +0.5 Input voltage Operating GP1F562T/GP1F553T Topr temperature GP1FB200TK Tstg Storage temperature Tsol Soldering temperature
times less)
3.35 Jack terminal configuration
Internal equivalent circuit Drive
7±0.1
players Portable players
4±0.15
Applications
2-1.2-0.1
Jack terminal Device terminal
(Internal connection)
Absolute Maximum Ratings(Jack)
Parameter Symbol Rating D.C. 12V, Total power dissipation Ptot Operating temperature Topr Tstg Storage temperature Tsol Soldering temperature Viso A.C. 500V Isolation voltage
times less) 1min
Unspecified tolerance ±0.3mm Reference dimensions
Unit
Notice absence confirmation device specification sheets, SHARP takes responsibility defects that occur equipment using SHARP devices shown catalogs, data books, etc. Contact SHARP order obtain latest device specification sheets before using SHARP device. Internet Internet address Electronic Components Group http://www.sharp.co.jp/ecg/
GP1F562T/GP1F553T/GP1FB200TK Recommended Operating Conditions
Parameter Symbol MIN. TYP. MAX. Unit GP1F562T Operating GP1F553T 4.75 5.25 supply voltage 2.30 GP1FB200TK Operating transfer rate Mbps
Electro-optical Characteristics
Parameter Peak emission wavelength Optical power output GP1F562T/GP1FB200TK coupling with fiber GP1F553T GP1F562T Dissipation GP1F553T current GP1FB200TK High level GP1F562T/GP1F553T dissipation current GP1FB200TK level GP1F562T/GP1F553T dissipation current GP1FB200TK GP1F562T High level GP1F553T input voltage GP1FB200TK level GP1F562T/GP1F553T input voltage GP1FB200TK High GP1F562T/GP1FB200TK delay time GP1F553T High GP1F562T/GP1FB200TK delay time GP1F553T Pulse width GP1F562T/GP1FB200TK distortion GP1F553T GP1F562T/GP1FB200TK Jitter GP1F553T Symbol Conditions Refer Fig.1 MIN.
Refer Fig.2 Refer Fig.2 Refer Fig.2
Ta=25°C VCC=3.0V (GP1F562T) VCC=5.0V (GP1F553T) VCC=2.5V (GP1FB200TK) MAX. Unit
TYP.
IccH IccL
Refer Fig.2
tpLH tpHL
Refer Fig.2 Refer Fig.3 Refer Fig.3 Refer Fig.3 Refer Fig.3
Mechanical Electrical Characteristics(Jack)
Parameter Insertion force, withdrawal force Contact resistance Isolation resistance Symbol Rcon Riso Conditions D.C. 500V, 1min. MIN. TYP. MAX. Unit
Note) This jack designed applicable compact single head plug (JIS C6560). Measuring method insertion force withdrawal force. Insertion withdrawal force shall measured after inserting withdrawing times using C6560 standard plug test. Measuring method contact resistance. measures 100mA less 1000Hz condition inserting C6560 standard plug test which movable contact terminal make contacts described.
GP1F562T/GP1F553T/GP1FB200TK Fig.1 Measuring Method Optical Output Coupling with Fiber
Standard optical fiber cable GP1F562T/ GP1F553T/ GP1FB200TK Unit measured Optical power meter (Anritsu)ML93B
optical power meter must calibrated have wavelength sensitivity 660nm. (0dBm=1mW)
Notes GP1F562T VCC=3.0±0.05V (State operating) GP1F553T VCC=5.0V (State operating) GP1FB200TK VCC=2.5V (State operating) bundle standard fiber optic cable, make into loop with diameter D=10cm more. (The standard fiber optic cable will specified elsewhere.)
Fig.2 Measuring Method Intput Voltage Supply Current
Standard optical fiber cable GP1F562T/ GP1F553T/ GP1FB200TK Unit measured optical power meter must calibrated have wavelength sensitivity 660nm. (0dBm=1mW) Optical power meter (Anritsu)ML93B
Input conditions judgement method (GP1F562T)
Conditions Vin=2.1V more Vin=0.8V less Judgement method -21<=PC<=-15dBm, ICC=12mA less PC<=-36dBm, ICC=12mA less
Note) VCC=3.0±0.05V (State operating)
Input conditions judgement method (GP1F553T)
Conditions Vin=2.0V more Vin=0.8V less Judgement method -22<=PC<=15dBm, ICC=10mA less PC<=-36dBm, ICC=10mA less
Note) VCC=5.0 (State operating)
Input conditions judgement method (GP1FB200TK)
Conditions Vin=1.9V more Vin=0.7V less Judgement method -21<=PC<=-15dBm, ICC=10mA less PC<=-36dBm, ICC=1.0mA less
Note) VCC=2.5 (State operating)
GP1F562T/GP1F553T/GP1FB200TK Fig.3 Measuring Method Pulse Response Jitter
GP1F562T/ GP1F553T/ GP1FB200TK Unit measured Standard optical fiber cable Standard receiver Output signal
Oscilloscope Input Tektronix 7834 7934 type Trigger Storage mode
Input signal
Input signal 3Mbps biphase PRBS signal
tPLH Standard receiver output
tPHL
Test item
Test item High pulse delay time High pulse delay time Pulse width distortion High Jitter High Jitter Symbol tPLH tPHL Test condition Refer above mentioned prescription. Refer above mentioned prescription. tw=tPHL-tPLH trigger rise input signal measure jitter rise output trigger fall input signal measure jitter fall output
Notes waveform write time shall seconds. allow waveform distorted increasing brightness much. GP1F562T VCC=3.0±0.05V (State operating) GP1F553T VCC=5.0V (State operating) GP1FB200TK VCC=2.5V (State operating) probe oscilloscope must more than less than 10pF.
Application Circuits
NOTICE
qThe circuit application examples this publication provided explain representative applications SHARP devices intended guarantee circuit design license intellectual property rights. SHARP takes responsibility problems related intellectual property right third party resulting from SHARP's devices. qContact SHARP order obtain latest device specification sheets before using SHARP device. SHARP reserves right make changes specifications, characteristics, data, materials, structure, other contents described herein time without notice order improve design reliability. Manufacturing locations also subject change without notice. qObserve following points when using devices this publication. SHARP takes responsibility damage caused improper devices which does meet conditions absolute maximum ratings used specified relevant specification sheet meet following conditions: devices this publication designed general electronic equipment designs such Personal computers Office automation equipment Telecommunication equipment [terminal] Test measurement equipment Industrial control Audio visual equipment Consumer electronics (ii)Measures such fail-safe function redundant design should taken ensure reliability safety when SHARP devices used connection with equipment that requires higher reliability such Transportation control safety equipment (i.e., aircraft, trains, automobiles, etc.) Traffic signals leakage sensor breakers Alarm equipment Various safety devices, etc. (iii)SHARP devices shall used connection with equipment that requires extremely high level reliability safety such Space applications Telecommunication equipment [trunk lines] Nuclear power control equipment Medical other life support equipment (e.g., scuba). qContact SHARP representative advance when intending SHARP devices "specific" applications other than those recommended SHARP when unclear which category mentioned above controls intended use. SHARP devices listed this publication fall within scope strategic products described Foreign Exchange Foreign Trade Control Japan, necessary obtain approval export such SHARP devices. qThis publication proprietary product SHARP copyrighted, with rights reserved. Under copyright laws, part this publication reproduced transmitted form means, electronic mechanical, purpose, whole part, without express written permission SHARP. Express written permission also required before this publication made third party. qContact consult with SHARP representative there questions about contents this publication.

GP1F562T/GP1F553T/GP1FB200TK Compact (adoption small jack mini pl

Top Searches for this datasheet

Other recent searches