Download

PDF Abstract Text:

­ Utilizes Different Array Protection Compared to the AT24C02 / 04 / 08 / 16

2-wire Serial EEPROM

Features
· Write Protect Pin for Hardware Data Protection
- Utilizes Different Array Protection Compared to the AT24C02 / 04 / 08 / 16
· Low-voltage and Standard-voltage Operation · · · · · · · · · · ·
2-wire Serial EEPROM
2K (256 x 8) 4K (512 x 8) 8K (1024 x 8) 16K (2048 x 8)
Description
The AT24C02A / 04A / 08A / 16A provides 2048 / 4096 / 8192 / 16384 bits of serial electrically erasable and programmable read only memory (EEPROM) organized as 256 / 512 / 1024 / 2048 words of 8 bits each. The device is optimized for use in many industrial and commercial applications where low power and low voltage operation are essential. The AT24C02A / 04A / 08A / 16A is available in space saving 8-lead PDIP, 8-lead JEDEC SOIC, 8-lead MAP and 8-lead TSSOP packages and is accessed via a 2-wire serial interface. In addition, the entire family is available in 2.7V (2.7V to 5.5V) and 1.8V (1.8V to 5.5V) versions.
AT24C02A AT24C04A AT24C08A AT24C16A
Pin Configurations
Pin Name A0 - A2 SDA SCL WP NC Function Address Inputs Serial Data Serial Clock Input Write Protect No-connect
8-lead PDIP
8-lead SOIC
8-lead MAP
8-lead TSSOP
Rev. 0976L-SEEPR-1 / 04
Bottom View
Absolute Maximum Ratings
Operating Temperature................. -55°C to +125°C Storage Temperature ................... -65°C to +150°C Voltage on Any Pin with Respect to Ground ...................-1.0V to +7.0V Maximum Operating Voltage ..................... 6.25V DC Output Current............................ 5.0 mA NOTICE: Stresses beyond those listed under "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress rating only and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability.
Block Diagram
Pin Description
SERIAL CLOCK (SCL): The SCL input is used to positive edge clock data into each EEPROM device and negative edge clock data out of each device. SERIAL DATA (SDA): The SDA pin is bidirectional for serial data transfer. This pin is open-drain driven and may be wire-ORed with any number of other open-drain or open collector devices. DEVICE / PAGE ADDRESSES (A2, A1, A0): The A2, A1 and A0 pins are device address inputs that must be hard wired for the AT24C02A. As many as eight 2K devices may be addressed on a single bus system (device addressing is discussed in detail under the Device Addressing section). The AT24C04A uses the A2 and A1 inputs for hard wire addressing and a total of four 4K devices may be addressed on a single bus system. The A0 pin is a no-connect.
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
The AT24C08A only uses the A2 input for hardwire addressing and a total of two 8K devices may be addressed on a single bus system. The A0 and A1 pins are noconnects. The AT24C16A does not use the device address pins, which limits the number of devices on a single bus to one. The A0, A1 and A2 pins are no-connects. WRITE PROTECT (WP): The AT24C02A / 04A / 08A / 16A have a Write Protect pin that provides hardware data protection. The Write Protect pin allows normal read / write operations when connected to ground (GND). When the Write Protect pin is connected to VCC, the write protection feature is enabled and operates as shown in the following table.
Part of the Array Protected WP Pin Status At VCC At GND 24C02A Upper Half (1K) Array 24C04A Upper Half (2K) Array 24C08A Full (8K) Array 24C16A Full (16K) Array
Normal Read / Write Operations
Memory Organization
AT24C02A, 2K SERIAL EEPROM: Internally organized with 32 pages of 8 bytes each, the 2K requires an 8-bit data word address for random word addressing. AT24C04A, 4K SERIAL EEPROM: The 4K is internally organized with 32 pages of 16 bytes each. Random word addressing requires a 9-bit data word address. AT24C08A, 8K SERIAL EEPROM: The 8K is internally organized with 64 pages of 16 bytes each. Random word addressing requires a 10-bit data word address. AT24C16A, 16K SERIAL EEPROM: The 16K is internally organized with 128 pages of 16 bytes each. Random word addressing requires an 11-bit data word address.
Pin Capacitance
0976L-SEEPR-1 / 04
DC Characteristics
Test Condition
Min 1.8 2.5 2.7 4.5
Max 5.5 5.5 5.5 5.5
1.0 3.0 3.0 4.0 4.0 18.0 3.0 3.0 VCC x 0.3 VCC + 0.5 0.4 0.2
Input High Level
1. VIL min and VIH max are reference only and are not tested.
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
AC Characteristics
AT24C02A / 04A / 08A / 16A 1.8V Symbol fSCL tLOW tHIGH tI tAA tBUF tHD.STA tSU.STA tHD.DAT tSU.DAT tR tF tSU.STO tDH tWR Endurance(3) Notes: Parameter Clock Frequency, SCL Clock Pulse Width Low Clock Pulse Width High Noise Suppression Time(2) Clock Low to Data Out Valid Time the bus must be free before a new transmission can start(3) Start Hold Time Start Set-up Time Data In Hold Time Data In Set-up Time Inputs Rise Time Inputs Fall Time
AT2402A / 04A / 08A 2.5V, 2.7V Min Max 400 4.7 4.0
AT24C16A 2.5V, 2.7V Min Max 400 1.3 0.6
AT24C02A / 04A / 08A / 16A 5.0V Min Max 400 1.2 0.6 Units kHz µs µs 50 0.1 1.2 0.6 0.6 0 100 0.9 ns µs µs µs µs µs ns 0.3 300 0.6 50 µs ns µs ns 5 1M ms Write Cycles
Max 100
4.7 4.0 100 0.1 4.7 4.0 4.7 0 200 1.0 300 4.7 100 5 1M 4.5
100 0.1 4.7 4.0 4.7 0 200 1.0 300 4.7 100 5 1M 1M 0.6 100 4.5 0.2 1.3 0.6 0.6 0 100
Stop Set-up Time Data Out Hold Time Write Cycle Time 5.0V, 25°C, Page Mode
0976L-SEEPR-1 / 04
Device Operation
CLOCK and DATA TRANSITIONS: The SDA pin is normally pulled high with an external device. Data on the SDA pin may change only during SCL low time periods (refer to Data Validity timing diagram). Data changes during SCL high periods will indicate a start or stop condition as defined below. START CONDITION: A high-to-low transition of SDA with SCL high is a start condition which must precede any other command (refer to Start and Stop Definition timing diagram). STOP CONDITION: A low-to-high transition of SDA with SCL high is a stop condition. After a read sequence, the stop command will place the EEPROM in a standby power mode (refer to Start and Stop Definition timing diagram). ACKNOWLEDGE: All addresses and data words are serially transmitted to and from the EEPROM in 8 bit words. The EEPROM sends a zero to acknowledge that it has received each word. This happens during the ninth clock cycle. STANDBY MODE: The AT24C02A / 04A / 08A / 16A features a low power standby mode which is enabled: (a) upon power-up and (b) after the receipt of the STOP bit and the completion of any internal operations. MEMORY RESET: After an interruption in protocol, power loss or system reset, any 2-wire part can be reset by following these steps: (a) Clock up to 9 cycles, (b) look for SDA high in each cycle while SCL is high and then (c) create a start condition as SDA is high.
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
Bus Timing (SCL: Serial Clock, SDA: Serial Data I / O)
Write Cycle Timing (SCL: Serial Clock, SDA: Serial Data I / O)
8th BIT WORDn
twr STOP CONDITION
Note:
START CONDITION
1. The write cycle time tWR is the time from a valid stop condition of a write sequence to the end of the interval clear / write cycle.
0976L-SEEPR-1 / 04
Data Validity
Start and Stop Definition
Output Acknowledge
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
Device Addressing
The 2K, 4K and 8K EEPROM devices all require an 8 bit device address word following a start condition to enable the chip for a read or write operation (refer to Figure 1). The device address word consists of a mandatory one, zero sequence for the first four most significant bits as shown. This is common to all the EEPROM devices. The next 3 bits are the A2, A1 and A0 device address bits for the 2K EEPROM. These 3 bits must compare to their corresponding hard-wired input pins. The 4K EEPROM only uses the A2 and A1 device address bits with the third bit being a memory page address bit. The two device address bits must compare to their corresponding hard-wired input pins. The A0 pin is no-connect. The 8K EEPROM only uses the A2 device address bit with the next 2 bits being for memory page addressing. The A2 bit must compare to its corresponding hard-wired input pin. The A1 and A0 pins are no-connect. The 16K EEPROM does not use the device address pins, which limits the number of devices on a single bus to one. The A0, A1 and A2 pins are no-connects. The eighth bit of the device address is the read / write operation select bit. A read operation is initiated if this bit is high and a write operation is initiated if this bit is low. Upon a compare of the device address, the EEPROM will output a zero. If a compare is not made, the chip will return to a standby state.
Write Operations
BYTE WRITE: A write operation requires an 8 bit data word address following the device address word and acknowledgement. Upon receipt of this address, the EEPROM will again respond with a zero and then clock in the first 8 bit data word. Following receipt of the 8 bit data word, the EEPROM will output a zero and the addressing device, such as a microcontroller, must terminate the write sequence with a stop condition. At this time the EEPROM enters an internally-timed write cycle, t WR , to the nonvolatile memory. All inputs are disabled during this write cycle and the EEPROM will not respond until the write is complete (refer to Figure 2). PAGE WRITE: The 2K EEPROM is capable of an 8-byte page write, and the 4K, 8K and 16K devices are capable of 16-byte page writes. A page write is initiated the same as a byte write, but the microcontroller does not send a stop condition after the first data word is clocked in. Instead, after the EEPROM acknowledges receipt of the first data word, the microcontroller can transmit up to seven (2K) or fifteen (4K, 8K, 16K) more data words. The EEPROM will respond with a zero after each data word received. The microcontroller must terminate the page write sequence with a stop condition (refer to Figure 3). The data word address lower three (2K) or four (4K, 8K, 16K) bits are internally incremented following the receipt of each data word. The higher data word address bits are not incremented, retaining the memory page row location. When the word address, internally generated, reaches the page boundary, the following byte is placed at the beginning of the same page. If more than eight (2K) or sixteen (4K, 8K, 16K) data words are transmitted to the EEPROM, the data word address will "roll over" and previous data will be overwritten. ACKNOWLEDGE POLLING: Once the internally-timed write cycle has started and the EEPROM inputs are disabled, acknowledge polling can be initiated. This involves sending a start condition followed by the device address word. The read / write bit is representative of the operation desired. Only if the internal write cycle has completed will the EEPROM respond with a zero allowing the read or write sequence to continue.
0976L-SEEPR-1 / 04
Read Operations
Read operations are initiated the same way as write operations with the exception that the read / write select bit in the device address word is set to one. There are three read operations: current address read, random address read and sequential read. CURRENT ADDRESS READ: The internal data word address counter maintains the last address accessed during the last read or write operation, incremented by one. This address stays valid between operations as long as the chip power is maintained. The address "roll over" during read is from the last byte of the last memory page to the first byte of the first page. The address "roll over" during write is from the last byte of the current page to the first byte of the same page. Once the device address with the read / write select bit set to one is clocked in and acknowledged by the EEPROM, the current address data word is serially clocked out. The microcontroller does not respond with an input zero but does generate a following stop condition (refer to Figure 4). RANDOM READ: A random read requires a "dummy" byte write sequence to load in the data word address. Once the device address word and data word address are clocked in and acknowledged by the EEPROM, the microcontroller must generate another start condition. The microcontroller now initiates a current address read by sending a device address with the read / write select bit high. The EEPROM acknowledges the device address and serially clocks out the data word. The microcontroller does not respond with a zero but does generate a following stop condition (refer to Figure 5). SEQUENTIAL READ: Sequential reads are initiated by either a current address read or a random address read. After the microcontroller receives a data word, it responds with an acknowledge. As long as the EEPROM receives an acknowledge, it will continue to increment the data word address and serially clock out sequential data words. When the memory address limit is reached, the data word address will "roll over" and the sequential read will continue. The sequential read operation is terminated when the microcontroller does not respond with a zero but does generate a following stop condition (refer to Figure 6). Figure 1. Device Address
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
Figure 2. Byte Write
DEVICE ADDRESS
WORD ADDRESS
Figure 3. Page Write
DEVICE ADDRESS
DATA (n)
DATA (n + 1)
DATA (n + x)
Figure 4. Current Address Read
DEVICE ADDRESS
0976L-SEEPR-1 / 04
Figure 5. Random Read
DEVICE ADDRESS
WORD ADDRESS n
DUMMY WRITE
Figure 6. Sequential Read
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
AT24C02A Ordering Information
Ordering Code AT24C02A-10PI-2.7 AT24C02AN-10SI-2.7 AT24C02A-10TI-2.7 AT24C02AY1-10YI-2.7 AT24C02A-10PI-1.8 AT24C02AN-10SI-1.8 AT24C02A-10TI-1.8 AT24C02AY1-10YI-1.8 AT24C02AN-10SU-2.7 AT24C02AN-10SU-1.8 AT24C02AN-10SE-2.7 Note: Package 8P3 8S1 8A2 8Y1 8P3 8S1 8A2 8Y1 8S1 8S1 8S1 Operation Range Industrial (-40°C to 85°C)
Industrial (-40°C to 85°C) Lead-Free / Halogen-Free / Industrial Temperature (-40°C to 85°C) High Grade / Extended Temperature (-40°C to 125°C)
For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table.
Package Type 8P3 8S1 8A2 8Y1 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 -1.8 Low Voltage (2.7V to 5.5V) Low Voltage (1.8V to 5.5V)
0976L-SEEPR-1 / 04
AT24C04A Ordering Information
Ordering Code AT24C04A-10PI-2.7 AT24C04AN-10SI-2.7 AT24C04A-10TI-2.7 AT24C04AY1-10YI-2.7 AT24C04A-10PI-1.8 AT24C04AN-10SI-1.8 AT24C04A-10TI-1.8 AT24C04AY1-10YI-1.8 AT24C04AN-10SU-2.7 AT24C04AN-10SU-1.8 AT24C04AN-10SE-2.7 Note: Package 8P3 8S1 8A2 8Y1 8P3 8S1 8A2 8Y1 8S1 8S1 8S1 Operation Range Industrial (-40°C to 85°C)
Industrial (-40°C to 85°C) Lead-Free / Halogen-Free / Industrial Temperature (-40°C to 85°C) High Grade / Extended Temperature (-40°C to 125°C)
For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table.
Package Type 8P3 8S1 8A2 8Y1 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 -1.8 Low Voltage (2.7V to 5.5V) Low Voltage (1.8V to 5.5V)
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
AT24C08A Ordering Information
Ordering Code AT24C08A-10PI-2.7 AT24C08AN-10SI-2.7 AT24C08A-10TI-2.7 AT24C08AY1-10YI-2.7 AT24C08A-10PI-1.8 AT24C08AN-10SI-1.8 AT24C08A-10TI-1.8 AT24C08AY1-10YI-1.8 AT24C08AN-10SU-2.7 AT24C08AN-10SU-1.8 AT24C08A-10TU-2.7 AT24C08A-10TU-1.8 AT24C08AN-10SE-2.7 Note: Package 8P3 8S1 8A2 8Y1 8P3 8S1 8A2 8Y1 8S1 8S1 8A2 8A2 8S1 Operation Range Industrial (-40°C to 85°C)
Industrial (-40°C to 85°C)
Lead-Free / Halogen-Free / Industrial Temperature (-40°C to 85°C) High Grade / Extended Temperature (-40°C to 125°C)
For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table.
Package Type 8P3 8S1 8A2 8Y1 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 -1.8 Low Voltage (2.7V to 5.5V) Low Voltage (1.8V to 5.5V)
0976L-SEEPR-1 / 04
AT24C16A Ordering Information
Ordering Code AT24C16A-10PI-2.7 AT24C16AN-10SI-2.7 AT24C16A-10TI-2.7 AT24C16AY1-10YI-2.7 AT24C16A-10PI-1.8 AT24C16AN-10SI-1.8 AT24C16A-10TI-1.8 AT24C16AY1-10YI-1.8 AT24C16AN-10SU-2.7 AT24C16AN-10SU-1.8 AT24C16A-10TU-2.7 AT24C16A-10TU-1.8 AT24C16AN-10SE-2.7 Note: Package 8P3 8S1 8A2 8Y1 8P3 8S1 8A2 8Y1 8S1 8S1 8A2 8A2 8S1 Operation Range Industrial (-40°C to 85°C)
Industrial (-40°C to 85°C)
Lead-Free / Halogen-Free / Industrial Temperature (-40°C to 85°C) High Grade / Extended Temperature (-40°C to 125°C)
For 2.7V devices used in the 4.5V to 5.5V range, please refer to performance values in the AC and DC characteristics table.
Package Type 8P3 8S1 8A2 8Y1 8-pin, 0.300" Wide, Plastic Dual Inline Package (PDIP) 8-lead, 0.150" Wide, Plastic Gull Wing Small Outline (JEDEC SOIC) 8-lead, 0.170" Wide, Thin Shrink Small Outline Package (TSSOP) 8-lead, 4.90 mm x 3.00 mm Body, Dual Footprint, Non-leaded, Miniature Array Package (MAP) Options -2.7 -1.8 Low Voltage (2.7V to 5.5V) Low Voltage (1.8V to 5.5V)
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
Packaging Information
8P3 - PDIP
Top View
End View
SYMBOL
A A2 b b2 b3 c D 0.115 0.014 0.045 0.030 0.008 0.355 0.005 0.300 0.240 0.310 0.250 0.100 BSC 0.300 BSC 0.115 0.130 0.130 0.018 0.060 0.039 0.010 0.365
4 PLCS
Side View
Notes:
1. This drawing is for general information only refer to JEDEC Drawing MS-001, Variation BA for additional information. 2. Dimensions A and L are measured with the package seated in JEDEC seating plane Gauge GS-3. 3. D, D1 and E1 dimensions do not include mold Flash or protrusions. Mold Flash or protrusions shall not exceed 0.010 inch. 4. E and eA measured with the leads constrained to be perpendicular to datum. 5. Pointed or rounded lead tips are preferred to ease insertion. 6. b2 and b3 maximum dimensions do not include Dambar protrusions. Dambar protrusions shall not exceed 0.010 (0.25 mm).
01 / 09 / 02 2325 Orchard Parkway San Jose, CA 95131 TITLE 8P3, 8-lead, 0.300" Wide Body, Plastic Dual In-line Package (PDIP) DRAWING NO. 8P3 REV. B
0976L-SEEPR-1 / 04
8S1 - JEDEC SOIC
Top View End View
Side View
Note: These drawings are for general information only. Refer to JEDEC Drawing MS-012, Variation AA for proper dimensions, tolerances, datums, etc.
10 / 7 / 03 1150 E. Cheyenne Mtn. Blvd. Colorado Springs, CO 80906 TITLE 8S1, 8-lead (0.150" Wide Body), Plastic Gull Wing Small Outline (JEDEC SOIC) DRAWING NO. 8S1 REV. B
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
AT24C02A / 04A / 08A / 16A
8A2 - TSSOP
Pin 1 indicator this corner
Top View
End View
Side View
Notes:
1. This drawing is for general information only. Refer to JEDEC Drawing MO-153, Variation AA, for proper dimensions, tolerances, datums, etc. 2. Dimension D does not include mold Flash, protrusions or gate burrs. Mold Flash, protrusions and gate burrs shall not exceed 0.15 mm (0.006 in) per side. 3. Dimension E1 does not include inter-lead Flash or protrusions. Inter-lead Flash and protrusions shall not exceed 0.25 mm (0.010 in) per side. 4. Dimension b does not include Dambar protrusion. Allowable Dambar protrusion shall be 0.08 mm total in excess of the b dimension at maximum material condition. Dambar cannot be located on the lower radius of the foot. Minimum space between protrusion and adjacent lead is 0.07 mm. 5. Dimension D and E1 to be determined at Datum Plane H. 5 / 30 / 02
2325 Orchard Parkway San Jose, CA 95131
TITLE 8A2, 8-lead, 4.4 mm Body, Plastic Thin Shrink Small Outline Package (TSSOP)
DRAWING NO. 8A2
REV. B
0976L-SEEPR-1 / 04
8Y1 - MAP
PIN 1 INDEX AREA
Top View
End View
Bottom View
SYMBOL
MIN - 0.00 4.70 2.80 0.85 0.85 0.25
NOM - - 4.90 3.00 1.00 1.00 0.30 0.65 TYP
MAX 0.90 0.05 5.10 3.20 1.15 1.15 0.35
Side View
2 / 28 / 03 2325 Orchard Parkway San Jose, CA 95131 TITLE 8Y1, 8-lead (4.90 x 3.00 mm Body) MSOP Array Package (MAP) Y1 DRAWING NO. 8Y1 REV. C
AT24C02A / 04A / 08A / 16A
0976L-SEEPR-1 / 04
Atmel Corporation
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 487-2600
Atmel Operations
Memory
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314
RF / Automotive
Theresienstrasse 2 Postfach 3535 74025 Heilbronn, Germany Tel: (49) 71-31-67-0 Fax: (49) 71-31-67-2340 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759
Regional Headquarters
Europe
Atmel Sarl Route des Arsenaux 41 Case Postale 80 CH-1705 Fribourg Switzerland Tel: (41) 26-426-5555 Fax: (41) 26-426-5500
Microcontrollers
2325 Orchard Parkway San Jose, CA 95131, USA Tel: 1(408) 441-0311 Fax: 1(408) 436-4314 La Chantrerie BP 70602 44306 Nantes Cedex 3, France Tel: (33) 2-40-18-18-18 Fax: (33) 2-40-18-19-60
Biometrics / Imaging / Hi-Rel MPU / High Speed Converters / RF Datacom
Avenue de Rochepleine BP 123 38521 Saint-Egreve Cedex, France Tel: (33) 4-76-58-30-00 Fax: (33) 4-76-58-34-80
Room 1219 Chinachem Golden Plaza 77 Mody Road Tsimshatsui East Kowloon Hong Kong Tel: (852) 2721-9778 Fax: (852) 2722-1369
ASIC / ASSP / Smart Cards
Zone Industrielle 13106 Rousset Cedex, France Tel: (33) 4-42-53-60-00 Fax: (33) 4-42-53-60-01 1150 East Cheyenne Mtn. Blvd. Colorado Springs, CO 80906, USA Tel: 1(719) 576-3300 Fax: 1(719) 540-1759 Scottish Enterprise Technology Park Maxwell Building East Kilbride G75 0QR, Scotland Tel: (44) 1355-803-000 Fax: (44) 1355-242-743
Japan
9F, Tonetsu Shinkawa Bldg. 1-24-8 Shinkawa Chuo-ku, Tokyo 104-0033 Japan Tel: (81) 3-3523-3551 Fax: (81) 3-3523-7581
Literature Requests
www.atmel.com / literature
Printed on recycled paper.
0976L-SEEPR-1 / 04 xM