4-bit Microcontroller with Driver SH6610C-based single-chip 4-bit

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

4-bit Microcontroller with Driver SH6610C-based single-chip 4-bit

Datasheet Thumbnail

Top Searches for this datasheet

SH66P14A
4-bit Microcontroller with Driver
SH6610C-based single-chip 4-bit microcontroller OTPROM: 4096 bits RAM: bits (System Data memory) Operation voltage: 2.5V 6.0V CMOS bi-directional pins 4-Level subroutine nesting (include interrupts) 8-bit auto re-load timer/counter 8-bit Base timer Powerful interrupt sources: External interrupts INT0 Internal interrupt (Timer0) Internal interrupt (Base Timer) Port's falling edge interrupt: PORTB INT1 driver: dots (1/8 duty bias) dots (1/4 duty bias) used scan output Built-in dual tone with noise generator Clock source OSC: (code option) Crystal oscillator 32.768K oscillator: 262K OSCX: (system register select) Ceramic oscillator 455K oscillator 1.8M Instruction cycle time: 122.07µs 32.768 crystal 15.27µs 8.79µs 455KHz ceramic 2.22µs power operation mode: HALT STOP power consumption Warm timer power reset
General Description
SH66P14A single chip microcontroller integrated with SRAM, ROM, Timer Dual-tone PSG, driver port. This chip builds dual-oscillator enhance total chip performance.
Configuration
SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 PA.1 PA.2
COM6/SEG33 COM5/SEG34 COM4 COM3 COM2 COM1 OSCI OSCO PC.0 OSCXO OSCXI PA.0
SH66P14A
V2.0
SH66P14A
Configuration
COM8 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18
RESET TEST VLCD SEG1 SEG2
SH66P14A
Block Diagram
OTPROM (4096 OSCX
OSCI OSCO OSCXI OSCXO
(512
8-BIT TIMER0
[0:3]
PORTB CORE
PORTA EXTERNAL
PA.0 INT0 PA.1 PA.2 PA.3
COMMON DRIVER
RESET
SEGMENT DRIVER SCAN REGISTER
[1:8] [1:34]
OPERATING VOLTAGE VOLTAGE GENERATOR
SH66P14A
Description
Designation SEG1 SEG30 VLCD, TEST
RESET
Description Segment signal output display; Share with scan output Connect with external divided resistance Test (Internal pull-low). connect user Reset input internal pull-up) Power supply programmable I/O, Vector interrupt INT1 programmable I/O, PA.0 shared with INT0 PA.1, PA.2shared with output program mode, PA.1 shared with DATA, shared with PINPGMB, shared with PINOE
Port Port
Port Port
OSCXI OSCXO OSCO OSCI COM1 COM4 COM5 COM8/SEG34 SEG31
Oscillator input Oscillator output Ground Oscillator output Oscillator input Common signal output display Common/segment signal output display
Description
Designation Description
SEG17 SEG1 SEG30 SEG18 VLCD, TEST RESET Port Port
Segment signal output display; share with scan output Segment signal output display; share with scan output Connect with external divided resistance Test (Internal pull-low). connect user Reset input internal pull-up) Power supply programmable I/O, Vector interrupt INT1 programmable I/O, PA.0 shared with INT0 PA.1, PA.2 shared with output program mode, PA.1 shared with DATA, shared with PINPGMB, shared with PINOE Oscillator input Oscillator output Ground Oscillator output Oscillator input Common signal output display Common/segment signal output display
Port Port
OSCXI OSCXO OSCO OSCI COM1 COM4 COM5 COM8/SEG34 SEG31
SH66P14A
Functional Description
contains following function blocks: Program Counter, Arithmetic Logic Unit (ALU), Carry Flag, Accumulator, Table Branch Register, Data Pointer (INX, DPH, DPM, DPL), Stack. (Program Counter) Program Counter used address program ROM. consists 12-bits: Page Register (PC11), Ripple Carry Counter (PC10, PC9, PC8, PC7, PC6, PC5, PC4, PC3, PC2, PC1, PC0). program counter normally increases (+1) with every execution instruction except following cases: When executing jump instruction (such JMP, BA0, BC); When executing subroutine call instruction (CALL); When interrupt occurs; When chip INITIAL RESET mode. program counter loaded with data corresponding each instruction. unconditional jump instruction (JMP) 1-bit page register higher than performs arithmetic logic operations. provides following functions: Binary addition/subtraction (ADC, SBC, ADD, SUB, ADI, SBI)
OTPROM
Decimal adjustment addition/subtraction (DAA, DAS) Logic operations (AND, EOR, ANDIM, EORIM, ORIM) Decision (BA0, BA1, BA2, BA3, BAZ, Logic Shift (SHR) Carry Flag (CY) holds overflow, which arithmetic operation generates. During interrupt service call instruction, carry flag pushed into stack restored back from stack RTNI instruction. unaffected RTNW instruction. Accumulator Accumulator 4-bit register holding results arithmetic logic unit. conjunction with ALU, data transfers between accumulator system register, RAM, data memory performed. Stack group registers used save contents (10-0) sequentially with each subroutine call interrupt. organized bits levels. saved levels maximum allowed total subroutine calls interrupts. contents Stack returned sequentially with return instructions (RTNI/RTNW). Stack operated first-in, last-out basis. This 4-level nesting includes both subroutine calls interrupts requests. Note that program execution enter abnormal state number calls interrupt requests exceeds bottom stack will shifted out.
OTPROM address 4096 words bits program area from $000 $FFF. Vector Address Area ($000 $004) program sequentially executed. There area address $000 through $004 that reserved special interrupt service routine such starting vector address.
Address Instruction Function
$000H $001H $002H $003H $004H
Instruction Instruction Instruction Instruction Instruction
Jump RESET service routine Jump INT0 service routine Jump Timer0 service routine Jump Base Timer service routine Jump INT1 service routine
Table Data Reference Table Data stored program memory referenced using Table Branch (TJMP) Return Constant (RTNW) instructions. Table Branch Register (TBR) Accumulator (AC) placed offset address program ROM. TJMP instruction branches into address ((PC11 PC8) (TBR, AC)). address determined RTNW return look-up value into (TBR, AC). code bit7-bit4 placed into bit3-bit0 into
SH66P14A
Built-in SRAM contains general-purpose data memory, RAM, system registers. They directly accessed instruction cycle. Because static nature, keep data after enters STOP HALT. Data Memory, RAM, System Register following memory allocation map: $000 $01F: System register $020 $1FF: Data memory (480 4bits, divided into banks) $300 $321, $328 $345, $350 $36D: space bits bits) Data Pointer Data Pointer indirectly address data memory. Pointer address located register (3-bits) (4-bits). addressing range have locations. Pseudo index address (INX) used read write Data memory, then address bit9-bit0 comes from DPH, DPL. Configuration System Register
Address Bit3 Bit2 Bit1 Bit0 Function Initial Value
IRQX TM0.3 BTM.3 T0L.3 T0H.3 PA.3 PB.3 PACR.3 PBCR.3 LPD3 TBR.3 INX.3 DPL3 PPULL
IET0 IRQT0 TM0.2 BTM.2 T0L.2 T0H.2 PA.2 PB.2 PACR.2 PBCR.2 LPD2 TBR.2 INX.2 DPL2 DPM.2 DPH.2 PAM2
IEBT IRQBT TM0.1 BTM.1 T0L.1 T0H.1 PA.1 PB.1 PC.1 PACR.1 PBCR.1 LPD1 TBR.1 INX1 DPL1 DPM.1 DPH.1 PAM1
IRQP TM0.0 BTM.0 T0L.0 T0H.0 PA.0 PB.0 PC.0 PACR.0 PBCR.0 LPD0 TBR.0 INX.0 DPL0 DPM.0 DPH.0
Interrupt enable flags Interrupt request flags Timer0 mode register Base timer mode register Timer0 load/counter nibble Timer0 load/counter high nibble Reserved PORTA PORTB Bonding option PORTA output port PORTB output port Enable Control (LPD3 0101: Enable (Default); 1010: Disable Table branch register Index register (INX) Data pointer nibble Data pointer middle nibble Data pointer high nibble Bit1, PA.1 PA.2 output PORT Bit0: Heavy load mode Bit3: Port pull-up control Bit0: Turn OSCX oscillator Bit1: clocks select OSCX/0: OSC) Bit3: OSCX type selection
0000 0000 0000 0000 0000 0000 0000 0000 (default) 0000 0000 0101 0000 0000 0000 0000 0000 0000
OXON
0000
SH66P14A
Address Bit3 Bit2 Bit1 Bit0 Function Initial Value
LPS1
LPS0
LCDOFF
DUTY
C1.3 OCT1 C2.3 C2.7 C2.11 OCT2 VOL1 SEL1
C1.2 C1.6 C2.2 C2.6 C2.10 C2.14 VOL0 SEL0
C1.1 C1.5 C2.1 C2.5 C2.9 C2.13 CH2EN
C1.0 C1.4 C2.0 C2.4 C2.8 C2.12 CH1EN
Bit0: Select DUTY (1/8 1/4) Bit1: Bit2, frequency control Bit2: segment output Bit3: Power degrade channel nibble channel 1high nibble Bit3: channel octave shift control channel nibble alarm output channel nibble channel nibble channel nibble Bit3: channel octave shift control Bit0, Bit1: Channel enable Bit2, Bit3: volume control Bit0, PSG1, PSG2 mode control Bit2, PSG1, PSG2 clock source selection Reserved
0000
0000 0000 0000 0000 0000 0000 0000 0000 0000
SH66P14A
Oscillator Circuit
Circuit Configuration SH66P14A on-chip oscillation circuits OSCX. frequency crystal (Typ. 32.768KHz) (Typ.262KHz) determined code option. This designed frequency operation. OSCX also types: ceramic (Typ.455KHz) (1.8M 2MHz) determined software option. designed high frequency operation. possible select high speed processing high frequency clock select power operation operation clock. starting reset initialization, starts oscillation OSCX turned off. Immediately after reset initialization, clock automatically selected system clock input source.
OSCI OSCO Frequency Clock Oscillator System clock Source Selector Switching control High Frequency Clock Oscillator System clock Generator Clock Base Timer
OSCXI OSCXO
Figure Oscillator Block Diagram
OSCX turn OSCX turn
OSCXO
OSCO
CLOCK
High frequency operation frequency operation Warm-up time Switch from OSCX Switch from OSCX High frequency operation
Figure Timing System Clock Switching
Oscillation generates basic clock pulses that provide peripherals (Timer0, LCD) with operating clock. Crystal Oscillator Type
STOP
OSCI
32768Hz OSCO
5-6p
SH66P14A
Oscillator Type
RBIAS STOP
OSCI
Ring Oscllator
OSCO
OSCX Oscillation OSCX clock oscillators. software options select ceramic CPU's clock. OSCX used, must masked Ceramic resonator OSCXI must connected GND. OSCX Ceramic Oscillator Type
CPUSTOP
OSCXI
455KHz Ceramic OSCXO
OSCX Oscillator Type
OSCXI CPUSTOP
Ring Oscllator
OSCXO
Control Oscillator oscillator control register configuration shown blow.
Address Bit3 Bit2 Bit1 Bit0
OXON
OXON: OSCX oscillation on/off. 0:Turn OSCX oscillation 1:Turn OSCX oscillation OXM: switching system clock. 0:select system clock 1:select OSCX system clock OXS: OSCX oscillator type selection 0:OSCX ceramic oscillator
1:OSCX oscillator Programming Notes takes least OSCX oscillation circuit until oscillation stabilizes. When switching system clock from OSCX, must wait minimum till OSCX oscillation active. However, start time varies with respect oscillator characteristics operational conditions. Therefore waiting time depends applications. When switching from OSCX OSC, turning OSCX instruction, OSCX turn control would delayed instruction cycle automatically prevent operation error.
SH66P14A
System Clock
system clock varies clock source changes. following table shows instruction execution time according each frequency system clock source.
32.768 Xtal (OSC Cycle time PORT 262K (OSC 455K ceramic Xtal (OSCX) 1.8M (OSCX) (OSCX)
122.07
17.778
8.79
2.22
provides 8-bidirectional pins. Each contains pull-up controllable program. When used input, PORT control register (PACR, PBCR) controls ON/OFF output buffer. PORTA These ports contain 8-bidirectional ports. circuit configuration PORTA shown below.
PULL_UP Pull_up PMOS
Port Control Register PORTX Port Data Register
DATA INPUT
RD_INPUT
ports SH66P14A accessed read/write system register. User output value port time. Bit3 PMOD register controls On/Off pull-ups simultaneously. Pull-up also controlled port data registers (PA, each port also. pull-up turned On/Off. Memory Addresses Listed Follow:
Address Bit3 Bit2 Bit1 Bit0
Port Control Register: Address
PORTA.3 PORTB.3
PORTA.2 PORTB.2
PORTA.1 PORTB.1
PORTA.0 PORTB.0
Bit3
Bit2
Bit1
Bit0
PACR.3 PBCR.3
PACR.2 PBCR.2
PACR.1 PBCR.1
PACR.0 PBCR.0
control register: PACR.X, PBCR.X output buffer. input buffer (Power initial).
Port Mode Register (PMOD) Address Bit3 Bit2 Bit1 Bit0 Function
PPULL
PAM2
PAM1
Bit1, Select PA.1, PA.2 port output Bit0: Hevey load mode Bit3: Port pull-up control Enable Enable pull-up
PAM1, PAM2: HLM: PPULL:
Please sees Enable heavy load mode Disable Port pull-up Disable pull-up
SH66P14A
Port Interrupt PORTB interrupt (falling edge) controlled Port register. means that interrupt request (IEx port high goes low) been activated touched conditions other port bits high level time port either output input. External PortA.0 shared external interrupts (active low).
Heavy Load Mode (HLM)
heavy load protection circuit when battery load becomes heavy. examples, when external buzzer sound external speaker turned this mode, crystal oscillator circuit been backed high gain. When setup this mode, more power would provided oscillator circuit. Unless necessary, careful this mode with software. Since mode enter would delay instruction, please activate heavy load driving least instruction wait cycle after setting through software. following shows programming setting. HLM: Heavy load protection mode released Heavy load protection mode set.
HEAVYLOAD
Instruction Cycle Time
Programmable Sound Generator (PSG)
channel1 channel2. functional block diagram follows:
MIXER CHANNEL2
OSCX
CHANNEL1
function provides four subfunctions wide applications. Programmable Sound Program sound created channels. Each channel programmed follows. Enable/Disable each channel sounds. Select each channel sound frequency. channel sounds mixed into output. output controlled volume levels. Fine Noise provide wide-band noise. wide-band noise volume controlled volume levels. Alarm provide many alarm functions through software. alarm carrier frequency programmed individually. alarm volume controlled volume levels. Remote Control remote control only expandable application sound. Since remote control frequency 56.13KHz 37.92KHz, software could select sound frequency.
SH66P14A
subblock diagram:
SEL0 SEL1
SEL1 SEL0
source
CLK-SLECTOR OSCX
OSC/2 OSCX OSCX/16
32.768K 262K 32.768K 262K OSCX 1.8M OSCX 455K OSCX 1.8M OSCX 455K
32.768K 262K 16.384K 131K 1.8M 455K 112.5K 28.4K
Figure block diagram
block selects clock sources that provides channel sources.
Channel
CH1EN OCT1 REGISTER C1.6~C1.0
SELECTOR DIVIDER1
OCT1
Scaling ratio
Channel
Channel constructed 7-bit pseudo random counter. Channel enabled/disabled CH1EN. creates either sound frequency alarm carrier frequency remote carrier frequency.
CH2EN
OCT2
NOISE GENERATOR C2.14~C2.0
SELECTOR
REGISTER C2.14~C2.0 C2.14~C2.8
SELECTOR
C2.3~C2.0
DIVIDER2
32Hz
ENEVLOP
ENEVLOP
OCT2
Scaling ratio
Channel constructed 15-bit pseudo random counter. Channel enabled/disabled CH2EN 15-bit wide-band noise generator 7-bit sound generator. also create alarm envelope signal.
Function
Sound generator. Sound generator. Sound generator.
Sound generator. Noise generator. Alarm mode register.
SH66P14A
Mixer
TIME SLOT VOL0 VOL1 PA.1 PAM1
Time Slot Control
Selector Selector
PA.1 PA.2
PA.2
PAM2
MIXER mixes CH1-OUT CH2-OUT into single tone output PA.1 PA.2, when PAM1 1PAM2 Then tone output controlled volume control into volume levels outputted PSG. PA.1 PA.2 controlled PAM1 PAM2
PAM2 PAM1 Function
PA.1: PORT. PA.2: PORT PA.1: output. PA.2: PORT PA.1: PORT. PA.2: output PA.1: output. PA.2: output
SEL1
SEL0
Vol. control
VOL1
VOL0
Vol. Level
Note:
Don't enable channels together produce tone, will produce some unpredicted errors. necessary channels together (e.g. play different melodies from channels), don't score always same tone then unpredicted errors will occur will ignore through user hearing.
SH66P14A
Value Divider Corresponding C1.6 C1.0 C2.14 C2.8 Shown Following Table: LSFR (C1.6 C1.0) (C2.14 C2.8) LSFR (C1.6 C1.0) (C2.14 C2.8) LSFR (C1.6 C1.0) (C2.14 C2.8) LSFR (C1.6 C1.0) (C2.14 C2.8)
SH66P14A
sound generator programmable sound working modes. software designer select clock sources clk. then select frequency divided value that controlled value C1.6 C1.0 C2.14 C2.8.In select volume level controlled VOL0, VOL1. music tone output both also control OCT1, OCT2 that shifts music tone octaves. Example1: CH1EN CH2EN OSCX 1.8M, SEL0 SEL1 112kHz; Switch 28kHz Vol. 112kHz
TIME SLOT Control level level level level
Example2: CH1EN CH2EN OSCX 1.8M, SEL0 SEL1 112kHz; Switch 28kHz; Vol. 112kHz
TIME SLOT CH1EN=0 Control level level level level
Example3: CH1EN CH2EN 32k, SEL0 SEL1 32kHz; Switch 32kHz vol. control, level hardware, software should VOL0 VOL1
TIME SLOT level
Note: 32KHz operations, volume control cannot used, because multiplexing frequency high enough switch sound! user wants turn completely, software must disable both channels. User should turn zero wave from output. Both CH1EN CH2EN should power operation mode. Example software designer wants create (channel mixed with (channel sound (the sound frequency, please Music table1 Music table2), level 3.He select suggestion follows. Select CH1EN CH2EN Select OSCX 1.8M SEL0 SEL1 112.5KHz. Select OCT1 value channel LSFR (C1.6 C1.0) 108. Please Music table1.So channel sound frequency 112.5Khz/8/(2 108) 64.10Hz sound frequency. Select OCT2= value channel LSFR (C2.8 C2.14) Please Music table1.So channel sound frequency 112.5Khz/1/(2 694.4Hz sound frequency Lastly, select VOL1 VOL0 level Note: designer provides crossing tables appendix that what designer prefers 32.768K 112.5K. noise generator fine noise created CH2. want create single noise, make music tone output. Otherwise wide-band noise music tone into single output through MIXER. Lastly select volume levels controlled VOL0, VOL1.
SH66P14A
Alarm Generator When alarm mode, provides alarm carrier frequency provides alarm envelope signal. Lastly select volume levels controlled VOL0, VOL1. channel nibble C2.0 C2.3 will alarm control register. Channel output would modulate with ALARM envelope control 32KHz 262KHz. carrier frequency programmed channel 1.In reading this alarm control register, read corresponding output envelope frequency (the 1Hz, 4Hz, 8Hz, 32Hz). Alarm Control Register (OSC 32KHz 262KHz)
C2.3 C2.2 C2.1 C2.0 Alarm output control
0000B ALARM 1010B CONTROL 0011B 0101B
envelop output output output 32Hz output
Figure Alarm Modulation Output 32.768KHz 262KHz
remote control remote control only expandable application sound. select tone output will create alarm frequency envelope signal. When channel programmed ALARM mode. Programmer ALARM mode register "0000B". Program adequate frequency output output. Then PAM1 PAM2 control envelope code. this way, remote control function implemented easily. remote frequency 56.73KHz 37.92KHz. software should select OSCX 455KHz, SEL1 SEL0 that 455KHz. Then select channel alarm mode (C1M OCT1 C2.0 C2.3 00H. VOL1, VOL2 Then select C1.6 C1.0 that output frequency 455KHz/1/(2 37.92KHz. select C1.6 C1.0 that output frequency 455KHz/1/(2 56.87KHz.
SH66P14A
Timer
SH66P14A 8-bit timer. timer consists 8-bit counter 8-bit preload register. timers provide following functions: 8-bit up-counting timer/counter. Automatic re-loads counter. 8-bit prescaler. Interrupt overflow from $00. Configuration Operation Timer-0 consists 8-bit write-only timer load register (TL0L, TL0H), 8-bit read-only timer counter (TC0L, TC0H). counter load register both have order digit high order digit. Writing data into timer load register (TL0L, TL0H) initialize timer counter. Load register programming: low-order digit should written first, then high-order digit. timer counter automatically loaded with contents load register when high order digit written counter counts overflow from $00. Timer Load Register: Since register would control physical READ WRITE operations. Please follow these rules: Write Operation: nibble first High nibble update counter
Read Operation: High nibble first; nibble followed.
Load Reg.
Load Reg.
8-bit timer counter Latch Reg.
Figure Timer Load Register Configure
Timer0 Interrupt timer overflow will generate internal interrupt request, when counter counts overflow from $00. interrupt enable flag enabled, then timer interrupt service routine will start. This also used wake from HALT mode.
Timer0 mode register (TM0) 8-bit counter prescaler overflow output pulses. 4-bit registers used timer control shown Table1. register selects input clock sources timer.
Table Timer0 Mode Registers ($02) TM0.3 TM0.2 TM0.1 TM0.0 Prescaler Clock Source
/2048 /512 /128 External Auto-Reload function
System clock System clock System clock System clock System clock System clock System clock
INT0
TM0.3 control function: without Auto-Reload function
SH66P14A
Base Timer
base timer that shared with warm-up timer clock source (Low frequency oscillation: Crystal 32.768KHz 262KHz). After reset, counts every clock-input signal. When counts $FF, right after next clock input, counter counts generates overflow. This causes interrupt base timer interrupt request flag 1.Therefore, base timer function interval timer periodically, generating overflow output every 256th clock signal output. timer accepts 4096Hz 32KHz clock, base timer generates accurate timing interrupt. This base time prescaler reset program accurate timing. This clock-input source sleeted Bregister.
Address Bit3 Bit2 Bit1 Bit0 Function
BTM.3
BTM.2
BTM.1
BTM.0
Base timer mode register
BTM.3 Disable base timer BTM.2 reset base timer
BTM.1 BTM.0
BTM.3 Enable base timer BTM.2 reset base timer
Prescaler Ratio Clock source
4096Hz 32KHz 4096Hz 32KHz 4096Hz 32KHz 4096Hz 32KHz
BTM[3] base timer counter reset
4096/32k 262k
4Bit Scaler
BTM[2]
SH66P14A
Driver
driver contains controller, voltage generator, common signal pins segment driver pins. There different driving modes programmable: duty bias, other duty bias. driving mode controlled system register power initialization status duty, bias. When duty bias mode used, COM5 used SEG34 SEG1 also used output port, selected system register $16. When SEG1 output port, writes data same addresses (350H-36DH). could used data memory needed. When "STOP" instruction executed, will turned off, data keeps same value before executing "STOP" instruction. Control Register
Address
LPS1
LPS0
LCDOFF
DUTY
on/off switch. off. DUTY: duty control duty, bias duty, bias LPS1, LPS0: clock frequency control 0,0: LCDCLK OSC/64 0,1: LCDCLK OSC/512 1,0: LCDCLK System clock/512 1,1: LCDCLK System clock/4096 System clock Instruction cycle time Frame frequency LCDCLK/16 Frame frequency duty; duty same frequency cycle.
Frequency LPS1, LPS0
LCDOFF:
32kHz (#), 32kHz, 32kHz (#), 32kHz, 32kHz(#), 32kHz, 262kHz (#), 262kHz, 262kHz (#), 262kHz 262kHz (#), 262kHz
OSCX 455kHz OSCX 455kHz OSCX 1.8MHz OSCX 1.8MHz OSCX 2MHz OSCX 2MHz OSCX 455kHz OSCX 455kHz OSCX 1.8MHz OSCX 1.8MHz OSCX 2MHz OSCX 2MHz
32Hz 32Hz 32Hz 32Hz 32Hz 32Hz 256Hz 256Hz 256Hz 256Hz 256Hz 256Hz
32Hz 32Hz 32Hz 32Hz 32Hz 32Hz
14Hz 55Hz 61Hz 14Hz 55Hz 61Hz
1/8Hz 1.7Hz 1/8Hz 6.9Hz 1/8Hz 7.6Hz 1.7Hz 6.9Hz 7.6Hz
before sleeted system clk. Frame frequency LCDCLK/16 (32Hz) When SCAN OUT, COMx pulled high. easy implement keyboard scan. When STOP mode, COMx SEGx pulled low. easily waken keyboard scan (Port interrupt). When HALT mode, COMx SEGx normal. easily waken base timertimer0 port interrupt.
SH66P14A
Power
SYSCLK/512 LPS1 OSC/64 LPS0 Power Switch Scaler DUTY
Power Supply Control Circuit
common driver
COM1~COM8
segment driver scan output
SEG1~SEG34
Figure Block Diagram Reference Only
Build-in special power control power modulation.
Address
O/S: segment/common segment output output ports segment output output ports. When voltage power would degraded about 0.5V, depending level. designed reduce extra contrast control output pins. Then fitted automatically different voltage levels software. Configuration duty, bias (COM1 4,SEG1
Address Bit3 COM4 Bit2 COM3 Bit1 COM2 Bit0 COM1 Address Bit3 COM4 Bit2 COM3 Bit1 COM2 Bit0 COM1
300H 301H 302H 303H 304H 305H 306H 307H 308H 309H 30AH 30BH 30CH 30DH 30EH 30FH 310H
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17
311H 312H 313H 314H 315H 316H 317H 318H 319H 31AH 31BH 31CH 31DH 31EH 31FH 320H 321H
SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34
SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34
SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34
SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30 SEG31 SEG32 SEG33 SEG34
SH66P14A
duty, bias (COM1 SEG1 Address Bit3 COM4 Bit2 COM3 Bit1 COM2 Bit0 COM1 Address Bit3 COM8 Bit2 COM7 Bit1 COM6 Bit0 COM5
300H 301H 302H 303H 304H 305H 306H 307H 308H 309H 30AH 30BH 30CH 30DH 30EH 30FH 310H 311H 312H 313H 314H 315H 316H 317H 318H 319H 31AH 31BH 31CH 31DH
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
328H 329H 32AH 32BH 32CH 32DH 32EH 32FH 330H 331H 332H 333H 334H 335H 336H 337H 338H 339H 33AH 33BH 33CH 33DH 33EH 33FH 340H 341H 342H 343H 344H 345H
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8 SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16 SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24 SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SEG1 used scan output port Address Bit0 Address Bit0 Address Bit0 Address Bit0
350H 351H 352H 353H 354H 355H 356H 357H
SEG1 SEG2 SEG3 SEG4 SEG5 SEG6 SEG7 SEG8
358H 359H 35AH 35BH 35CH 35DH 35EH 35FH
SEG9 SEG10 SEG11 SEG12 SEG13 SEG14 SEG15 SEG16
360H 361H 362H 363H 364H 365H 366H 367H
SEG17 SEG18 SEG19 SEG20 SEG21 SEG22 SEG23 SEG24
368H 369H 36AH 36BH 36CH 36DH
SEG25 SEG26 SEG27 SEG28 SEG29 SEG30
SH66P14A
Waveform
DUTY BIAS SELECT UNSELECT VLCD SELECT UNSELECT VLCD SELECT UNSELECT DUTY BIAS SELECT UNSELECT VLCD
VLCD
Example Duty Bias
VLCD
COM1 COM2 COM3 COM4 COM5 COM6 COM7 COM8 SEG1 SEG30 FRAME CYCLE
This example SEG1 SEG30 COM1, COM3, COM5, COM7 lighted. SEG1 -SEG30 COM2, COM4, COM6, COM8 lighted.
SH66P14A
Interrupt
interrupt sources available SH66P14A: External interrupt INT0 Timer0 interrupt Base timer interrupt Port's falling edge detection interrupt( INT1 Configuration System Register $00:
Address Function
IET0
IEBT
Enable/0: Disable
External Interrupt INT0 External interrupt shared with PA.0, falling edge active. When register (IEX) external interrupt enabled, writing PA.0 will generate external interrupt. Timer interrupt, Base Timer Interrupt, Port Interrupt INT1 then valid interrupt requests will cause interrupt. overflow timer will create interrupt timer 0.The overflow Base timer will create interrupt Base timer. falling edge every port PORTB will create INT1 interrupt (The condition that other port must input/output high level). Enable Flags Request Flags Both Enable flags Request flags mapped system register. They read written software. When interrupt request generated (IRQx interrupt will activated vector address will generated from priority corresponding interrupt sources. When interrupt occurs, flag will saved into stack memory jump interrupt service vector address. After interrupt occurs, interrupt enable flags (IEx) reset automatically, when IRQx again, interrupt will activated vector address will generated from priority corresponding interrupt sources. Interrupt Servicing Sequence Diagram: During SH6610C interrupt service, user enable interrupt enable flag before returning from interrupt. servicing sequence diagram shows next interrupt next nesting interrupt occurrences. interrupt request ready instruction execution enable, then interrupt will start immediately after next instruction executions. However, instruction instruction disables interrupt request enable flag, then interrupt service will terminated.
Inst. cycle
Instruction Execution
Instruction Execution
Instruction Execution
Interrupt Generated
Interrupt Accepted
Vector Generated Stacking
Fetch Vector address Reset IE.X
Start vector address
SH66P14A
Options
Bonding Options System register reserved user opened system developer select these bonding options, selecting subprogram that programmed user.
$0A.1 (PC.1) $0A.0 (PC.0)
PC.0 PC.1
PC.0
goto subroutine goto subroutine (Default) goto subroutine goto subroutine
PC.1
PC.0
PC.1
PC.0 PC.1
PC.0
PC.1
PC.0
PC.1
PC.0
PC.1
PC.0
PC.1
SH66P14A Bonding Option
Code Option Oscillator (OSC) type: 32.768KHz crystal (Default) 262KHz
HALT STOP Mode
After execution HALT instruction, SH66P14A will enter halt mode. halt mode, will stop operating. peripheral circuit (Timer Base timer) will keep operating. After execution STOP instruction, SH66P14A will enter stop mode. stop mode, whole chip (including oscillator) will stop operating. HALT mode, SH66P14A waked interrupt occurs. STOP mode, SH66P14A waked port interrupt occurs.
Warm-up Counter
mode, warm-up counter prescaler divided (128). Crystal mode, warm-up counter prescaler divided (32768).
SH66P14A
Instruction
instructions cycle word instruction. characteristic memory-oriented operation. Arithmetic Logical Instruction
Accumulator Type Mnemonic Instruction Code Function Flag Change
ADCM ADDM SBCM SUBM EORM ANDM
00000 0bbb xxxx 00000 1bbb xxxx 00001 0bbb xxxx 00001 1bbb xxxx 00010 0bbb xxxx 00010 1bbb xxxx 00011 0bbb xxxx 00011 1bbb xxxx 00100 0bbb xxxx 00100 1bbb xxxx 00101 0bbb xxxx 00101 1bbb xxxx 00110 0bbb xxxx 00110 1bbb xxxx 11110 0000 0000
[3]; shift right
Immediate Type Mnemonic Instruction Code Function Flag Change
ADIM SBIM EORIM ORIM ANDIM
01000 iiii xxxx 01001 iiii xxxx 01010 iiii xxxx 01011 iiii xxxx 01100 iiii xxxx 01101 iiii xxxx 01110 iiii xxxx
Decimal Adjust Mnemonic Instruction Code Function Flag Change
11001 0110 xxxx 11001 1010 xxxx
Decimal adjust add. Decimal adjust sub.
SH66P14A
Transfer Instruction Mnemonic Instruction Code Function Flag Change
00111 0bbb xxxx 00111 1bbb xxxx 01111 iiii xxxx
Control Instruction Mnemonic Instruction Code Function Flag Change
10010 xxxx xxxx 10000 xxxx xxxx 10011 xxxx xxxx 10001 xxxx xxxx 10100 xxxx xxxx 10101 xxxx xxxx 10110 xxxx xxxx 10111 xxxx xxxx 11000 xxxx xxxx 11010 000h llll 11010 1000 0000 11011 0000 0000 11011 1000 0000 1110p xxxx xxxx 11110 1111 1111 11111 1111 1111
(Not include hhhh; llll
CALL RTNW RTNI HALT STOP TJMP
Where
(Include (PC11-PC8) (TBR) (AC) Operation
Program counter Accumulator Complement accumulator Carry flag Data memory page Stack
Immediate data Logical exclusive Logical Logical bank
Table Branch Register
SH66P14A
Absolute Maximum Rating*
Supply Voltage .-0.3V +7.0V Input Voltage -0.3V 0.3V Operating Ambient Temperature Storage Temperature .-55 +125
Electrical Characteristics
*Comments
Stresses above those listed under Absolute Maximum Ratings" cause permanent damage this device. These stress ratings only. Functional operation this device these other conditions above those indicated operational sections this specification implied intended. Exposure absolute maximum rating conditions extended periods affect device reliability.
(VDD 3.0V, 25°C, FOSC 32.768KHz, FOSCX used, unless otherwise specified)
Parameter Symbol Min. Typ. Max. Unit Conditions
Operating Voltage Operating Current voltage divider resistor Standby Current Standby Current Input High Voltage Input Voltage Drive-high resistance Output high voltage Output voltage Output high voltage Output voltage Output high voltage Output voltage Output high voltage Output voltage Output high voltage Output voltage lighting
RLCD ISB1 ISB2 VOH1 VOL1 VOH2 VOL2 VOH3 VOL3 VOH4 VOL4 VOH5 VOL5 ILCD
0.85 -0.3
0.15
output pins unload execute instruction exclude bias current,
output pins unload (HALT mode) exclude bias current, output pins unload (STOP mode), off, PORTA, PORTB INT0 RESET PORTA, PORTB INT0 RESET PORTA, PORTB (IOH -10µA, PORTA.0, PORTA.3, PORTB (IOH -2mA) PORTA.0, PORTA.3, PORTB (IOL 2mA) PORTA.1, PORTA.2 output, -5mA PORTA.1, PORTA.2 output, SEGx, 50P, rise time 1000ns SEGx SEG1 30to output port, -1mA SEG1 30to output port, COMx, -1mA COMx, exclude core operation current
Operation frequency ISB1 ISB1X (Frequency/32.768KHz) ISB1 0.8, (VDD 3.0V) Operation frequency IOPX (Frequency/32.768KHz) 0.8, (VDD 3.0V) IOP, ISB1 ISB2 IOPX ISB2X ISB2
Circuitry
(GND 25°C, FOSC 32.768KHz, unless otherwise specified)
Parameter Symbol Min. Typ. Max. Unit Condition
LPD-detected Voltage
VLPD
SH66P14A
Characteristics
(VDD 3.0V, 25°C, FOSC 32.768KHz, unless otherwise specified)
Parameter Symbol Min. Typ. Max. Unit Conditions
Oscillation Start Time Frequency Stability
Characteristics
tSTT |F|/F
[F(3.0)-F(2.4)]/F(3.0), crystal oscillator
(VDD 3.0V, 25°C, FOSC 262KHz, FOSCX stop, unless otherwise specified)
Parameter Symbol Min. Typ. Max. Unit Conditions
Oscillation Start Time Frequency Stability
Characteristics
tSTT |F|/F
[F(3.0)-F(2.4)]/F(3.0), Bias resistance accuracy within
(VDD 4.5V, 25°C, FOSC 262KHz, FOSCX stop, unless otherwise specified)
Parameter Symbol Min. Typ. Max. Unit Conditions
Frequency Stability
|F|/F
[F(4.5)-F(3.6)]/F(4.5), Bias resistance accuracy within
Typical Oscillator Resistor Frequency: (for reference only)
(VDD 3.0V)
1000 200.00
250.00
300.00
350.00
400.00
450.00
(KHz)
Figure Resistor FOSC
(VDD 3.0V)
1700.00 1800.00 1900.00 2000.00 2100.00 2200.00 (KHz)
Figure Resistor FOSCX
SH66P14A
Application Circuit (for reference only)
AP1:
OSC: Crystal oscillator 32.768KHz (code option) OSCX: Ceramic oscillator 455KHz PORTB: PORTA.1, PORTA.2: ALARM output LCD: Internal duty, bias
duty bias 100p RESET OSCXO OSCXI 455KHz
SH66P14A
PORTB OSCO
PORTA.1 BUZZER
32768Hz OSCI TEST
PORTA.2
AP2:
OSC: oscillator 262KHz (mask option) LCD: Internal duty, bias PORTA, PORTB: PORTA.0: External interrupt
duty bias
RESET
OSCXI
OSCXO PORTA PORTB OSCO 930K OSCI TEST
SH66P14A
PORTA.0
Ext.int
SH66P14A
AP3:
OSC: Crystal oscillator 32.768KHz (mask option) OSCX: oscillator 1.8MHz PORTB: PORTA.1: output PORTA.2: output
RESET
OSCXI
120K (VDD
SPEAKETR
OSCXO
SH66P14A
PORTB OSCO
PORTA.1
8050
32768Hz OSCI TEST
PORTA.2
AP4:
Internal bias.1/8 DUTY bias SEG1 SEG4 SCAN output port
COM1 COM8 SEG30
PANNEL
BOARD
SH66P14A
SEG4 SEG3 SEG2 SEG1 PORTB0 PORTB1 PORTB2 PORTB3
SH66P14A
AP5:
Large panel: External bias
Bias Bias Normal pannel Bias Large pannel VLCD Ext.R SH66P14A SH66P14A Ext.R Ext.R Ext.R SH66P14A Ext.R Bias Large pannel
VLCD
VLCD Ext.R
VCC, floating
SH66P14A
Music Table1
Following music scale reference table channel 1(or channel under OSCX 1.8MHz. octave possible. Music scale data 1.8M OSCX SEL0 SEL1
Note Ideal freq. LSFR Real OCT1 Error% Note (C1.6~C1.0) freq. /OCT2 (C2.14~C2.8) 61.68 -0.08 Ideal freq. LSFR Real OCT1/ Error% (C1.6~C1.0) freq. OCT2 (C2.14~C2.8) 493.42 -0.09
61.73 65.10 69.29 73.42 77.78 82.41 87.31 92.50 98.00 110.00 123.47 130.81 146.83 164.81 174.61 184.99 196.00 220.00 246.94 261.63 293.66 329.63 349.23 369.99 392.00 440.00 493.88
493.88 523.25 554.35 587.33 622.24 659.26 698.46 739.97 783.99 830.59 880.00 932.31 987.77 1046.48 1108.71 1174.63 1244.48 1318.48 1396.88 1479.95 1567.95 1661.18 1759.96 1864.62 1975.49 2092.96 2217.41 2349.27 2488.96 2636.96 2793.77 2959.89 3135.90 3322.37 3519.93 3729.23 3950.98
65.10 69.62 73.24 78.13 82.72 86.81 92.52 97.66 103.40 109.86 117.19 123.36 130.21 137.87 146.48 156.25 163.52 175.78 185.03 195.31 206.80 219.73 234.38 251.12 260.42 281.25 292.97 305.71 334.82 351.56 370.07 390.63 413.60 439.45 468.75 502.23
0.01 0.47 -0.24 0.44 0.38 -0.58 0.02 -0.35 -0.40 -0.13 0.56 -0.09 -0.46 -0.52 -0.24 0.44 -0.79 0.67 0.02 -0.35 -0.41 -0.12 0.56 1.69 -0.46 1.47 -0.24 -1.74 1.58 0.67 0.02 -0.35 -0.41 -0.12 0.56 1.69
520.83 556.93 585.94 625.00 661.77 694.44 740.13 781.25 827.21 878.91 937.50 986.84 1041.67 1102.94 1171.88 1250.00 1308.14 1406.25 1480.26 1562.50 1654.41 1757.81 1875.00 2008.93 2083.33 2250.00 2343.75 2445.65 2678.57 2812.50 2960.53 3125.00 3308.82 3515.63 3750.00 4017.86
-0.46 0.47 -0.24 0.44 0.38 -0.58 0.02 -0.35 -0.41 -0.12 0.56 -0.09 -0.46 -0.52 -0.24 0.44 -0.78 0.67 0.02 -0.35 -0.41 -0.12 0.56 1.69 -0.46 1.47 -0.24 -1.74 1.58 0.67 0.02 -0.35 -0.41 -0.12 0.56 1.69
103.82 116.54
138.59 155.56
207.65 233.08
277.18 311.12
415.30 466.15
SH66P14A
Music Table2
Following music scale reference table channel 1(or channel under 32.768KHz. 4-octave possible. Music scale data SEL0 SEL1
Note Ideal freq. LSFR OCT1 (C1.6~C1.0) /OCT2 (C2.14~C2.8) Real freq. Error% Note Ideal freq. LSFR OCT1 (C1.6~C1.0) /OCT2 (C2.14~C2.8) Real freq. Error%
55.00 58.27 61.73 65.41 69.29 73.42 77.78 82.41 87.31 92.50 98.00
55.35 58.51 62.06 66.07 68.27 73.14 78.77 81.92 89.04 93.09 97.52 102.40 107.79 113.78 120.47 128.00 136.53 146.29 156.04 165.50 174.30 184.09 195.05 207.39 221.41 234.06 248.24
0.64 0.42 0.54 1.00 -1.48 -0.38 1.27 -0.60 1.99 0.64 -0.49 -1.37 -2.01 -2.37 -2.43 -2.15 -1.48 -0.37 0.31 0.42 -0.18 -0.49 -0.49 -0.12 0.64 0.42 0.53
261.63 277.18 293.66 311.12 329.63 349.23 369.99 392.00
260.06 277.70 292.57 309.13 327.68 348.60 372.36 390.10 420.10 442.81 468.11 496.49 528.52 546.13 585.14 630.15 655.36 712.35 744.73 780.19 819.20 862.32 910.22 963.77 1024.00 1092.27 1170.29
-0.60 0.19 -0.37 -0.64 -0.59 -0.18 0.64 -0.49 1.16 0.64 0.42 0.53 1.01 -1.48 -0.37 1.27 -0.59 1.99 0.64 -0.49 -1.37 -2.01 -2.37 -2.43 -2.15 -1.48 -0.37
415.30
440.00 466.15 493.88 523.25 554.35 587.33 622.24 659.26 698.46 739.97 783.99
103.82
110.00 116.54 123.47 130.81 138.59 146.83 155.56 164.81 174.61 184.99 196.00
830.59
880.00 932.31 987.77
207.65
220.00 233.08 246.94
1046.48
1108.71
1174.63
SH66P14A
Ordering Informations
Part Packages
SH66P14AH SH66P14AF
CHIP FORM
SH66P14A
Bonding Diagram
SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 PA.1 PA.2 (0,0) COM7/SEG32 COM6/SEG33 COM5/SEG34 COM4 COM3 COM2 COM1 OSCI OSCO PC.0 OSCXO OSCXI PA.0 1960µm
SH66P14A
SEG3
2080
Substrate connect
Designation SEG2 SEG1 VLCD TEST RESET Bonding options PC.1 PB.3 PB.2 PB.1 PB.0 PA.3 PA.2 PA.1 PA.0 OSCXI OSCXO Bonding options PC.0 OSCO OSCI COM1 COM2 COM3 COM4 COM5/SEG34 COM6/SEG33 (µm) -784 -664 -544 -424 -304 -184 (µm) -854 -854 -854 -854 -854 -854 -854 -854 -758 -854 -854 -854 -854 -854 -854 -854 -724 -604 -484 -364 -236 -236 -116 Designation COM7/SEG32 COM8/SEG31 SEG30 SEG29 SEG28 SEG27 SEG26 SEG25 SEG24 SEG23 SEG22 SEG21 SEG20 SEG19 SEG18 SEG17 SEG16 SEG15 SEG14 SEG13 SEG12 SEG11 SEG10 SEG9 SEG8 SEG7 SEG6 SEG5 SEG4 SEG3 (µm) -180 -300 -420 -540 -660 -784 -904 -916 -916 -916 -916 -916 -916 -916 -916 -916 -916 -916 -916 -916 -904 (µm) -120 -240 -360 -480 -600 -724 -854
SH66P14A
Package Informations
100L Outline Dimensions
unit: inch/mm
Detail Seating Plane
Detail
Symbol
Dimensions inch
Dimensions
0.130 Max. 0.004 Min. 0.112 0.005 0.012 +0.004 -0.002
3.30 Max. 0.10 Min. 2.85 0.13 0.31 +0.10 -0.05 0.15 +0.10 -0.05 14.00 0.13 20.00 0.13 0.65 0.15 18.85 NOM. 17.60 NOM. 23.60 NOM. 18.80 0.31 24.79 0.31 1.19 0.20 2.41 0.20 0.15 Max.
0.006 +0.004 -0.002 0.551 0.005 0.787 0.005 0.026 0.006 0.742 NOM. 0.693 NOM. 0.929 NOM. 0.740 0.012 0.976 0.012 0.047 0.008 0.095 0.008 0.006 Max.
Notes:
Dimensions include resin fins. Dimensions Board surfaces mount pitch (Design reference only).
SH66P14A
Data Sheet Version History
Version Content Date
change Final Data Sheet Preliminary SPEC Bonding diagram added. Application circuit changed Original
Dec.2002 Aug.2002 Mar.2002 Aug.2001

4-bit Microcontroller with Driver SH6610C-based single-chip 4-bit

Top Searches for this datasheet

Other recent searches