SLP-4118B-51 Infrared SLP-4118B-51 yellow contact type

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

SLP-4118B-51 Infrared SLP-4118B-51 yellow contact type

Datasheet Thumbnail

Top Searches for this datasheet

Ordering number EN6057
SLP-4118B-51
Infrared
SLP-4118B-51
yellow contact type lamp
Features
GaAsP yellow round type lamp Diffused yellow resin package type insertion which made stick possible High luminous intensity, high reliability long life Application general public welfare
1.55
Note Material lron Coating Solder Lead center Unit
10.2
(not soldered)
Absolute Maximum Ratings Ta=25°C 7032)
Parameter Forward Current Pulse Forward Current Reverse Voltage Power Dissipation Operating Temperature Storage Temperature Soldering Temperature
Symbol Topr Tstg Tsol
Rating
Unit
29.5
Anode Cathode
forward current derating Pulse width Max. 10ms Duty ratio Max. Max. 5sec., Lead soldering condition Min. 1.6mm from case (used 1.6mm't PCB)
Electrical Optical Characteristics Ta=25°C
Parameter Symbol Conditions Min. Typ. Foward Voltage 20mA Reverse Current Luminous Intensity 20mA Peak Wave length 20mA Line Half Width 20mA Capacitance 1MHz Response Time Luminous Intensity measured J-16 (SONY TEKTRONIX) which office possess. Max. Unit
Note
unit sack.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
52699 (MI) No.6057
(1.5)
SLP-4118B-51
Typical Characteristics
CAUTION These shows electrical optical characteristics this products, assure this dispersive contents.
Forward Current Forward Voltage
Intensity Temperature constant)
Forward Current (mA)
Relative Intensity
Forward Voltage
Temperature (°C)
Intensity Current
Spectrum
Relative Intensity
Relative Intensity
Forward Current (mA)
Wave Length (nm)
Forward Current Derating (Abusolute Maximum Rating)
Directivity
Forward Current (mA)
Temperature (°C)
No.6057
SLP-4118B-51
PRECAUTIONS Bending lead should avoid cause chip deterioration When bending necessary, care must taken considering following points Bending lead must done before soldering. Bending lead must done states fixing lead tight applying stress resin part; otherwise cause troubles such gold wire breaking. lead must bent intervals 1.6mm from edge resin part. bend same portion lead more than twice. Setting product tool such holder should avoid. When necessary, stress should applied resin part lead sufficient considerations dimension tolerance, thermal expansion, thermal contraction holder, product circuit board. hole pitch circuit board must lead pitch. When soldering, care must taken considering following points heat product under stress (ex. twist) leads. heat soldering, example) product states being forced resin part. flux containing chlorine which cause corrosion lead washing preferable. When washing necessary, avoid washing whole product wash only needed part under following conditions. Chemicals Methyl alcohol Temperature 45°C max. Time 30sec. max.
No.6057
SLP-4118B-51
CAUTION
products described contained herein intended surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster crime-prevention equipment like, failure which directly indirectly cause injury, death property loss. Anyone purchasing products described contained herein above-mentioned shall: Accept full responsibility indemnify defend SANYO ELECTRIC CO.,LTD., it's affiliates, subsidiaries distributors their officers employees, jointly severally, against claims litigation damages, costs expenses associated with such use. impose responsibility fault negligence which cited such claim litigation SANYO ELECTRIC CO., LTD., it's affiliates, subsidiaries distributors their officers employees jointly severally. Information (including circuit diagrams circuit parameters) disclosed herein example only; guaranteed mass production, SANYO believes information disclosed herein accurate reliable, guarantees made implied regarding it's infringements intellectual property rights other rights third parties.
Precautionary instructions handling gallium arsenic products
Special precautions must taken handling this product because contains, gallium arsenic, which designated toxic substance law. sure adhere strictly applicable laws regulations enacted this substance, particularly when comes disposal.
Manufactured Tottori SANYO Electric Co., Ltd. Division 5-318, Tachikawa-cho, Tottori City, 680-8634 Japan TEL: +81-857-21-2137 FAX: +81-857-21-2161
No.6057

SLP-4118B-51 Infrared SLP-4118B-51 yellow contact type

Top Searches for this datasheet

Other recent searches