HCPL-J314 Minimum Peak Output Current High Speed Response: Max. P

The Datasheet Archive - 100 Million Datasheets from 7500 Manufacturers.

HCPL-J314 Minimum Peak Output Current High Speed Response: Max. P

Datasheet Thumbnail

Top Searches for this datasheet

Output Current IGBT Gate Drive Optocoupler Technical Data
HCPL-J314
Minimum Peak Output Current High Speed Response: Max. Propagation Delay over Temp. Range Ultra High CMR: Min. kV/µs Bootstrappable Supply Current: Max. Wide Operating Temp. Range: -40°C 100°C Wide Operating Range: over Temp. Range Available DIP8 (Single) SO16 (Dual) Package Safety Approvals: Recognized, 3750 Vrms Minute. Approval IEC/EN/DIN 60747-5-2 Approval. VIORM=891 Vpeak
Description
HCPL-J314 family devices consists AlGaAs optically coupled integrated circuit with power output stage. These optocouplers ideally suited driving power IGBTs MOSFETs used motor control inverter applications. high operating voltage range output stage provides drive voltages required gate controlled devices. voltage current supplied this optocoupler makes ideally suited directly driving small medium power IGBTs. IGBTs with higher ratings HCPL-3150(0.5A) HCPL-3120 (2.0A) optocouplers used.
Functional Diagram
ANODE CATHODE
SHIELD
HCPL-J314
Truth Table
HIGH
Applications
Isolated IGBT/Power MOSFET Gate Drive Brushless Motor Drives Inverters Appliances Industrial Inverters Switch Mode Power Supplies (SMPS) Uninterruptable Power Supplies (UPS)
bypass capacitor must connected between pins CAUTION: advised that normal static precautions taken handling assembly this component prevent damage and/or degradation which induced ESD.
Selection Guide
Package Type 8-pin (300 Mil) SO16 Part Number HCPL-J314 HCPL-314J Number Channels
Ordering Information
Specify part number followed option number desired). Example
HCPL-J314#XXXX option Standard package, tube. Gull Wing Surface Mount Option, tube. Tape Reel Packaging Option. XXXE Lead Free Option.
HCPL-314J#YYYY option SO16 Package. Tape Reel Packaging Option. XXXE Lead Free Option.
Remarks: notation used existing products, while (new) products launched since 15th July 2001 lead free option will
HCPL-J314 Package Outline Drawings
Standard Package
9.80 0.25 (0.386 0.010) DATE CODE 7.62 0.25 (0.300 0.010) 6.35 0.25 (0.250 0.010)
HCPL-J314 YYWW 1.19 (0.047) MAX.
1.78 (0.070) MAX. 0.076 0.254 0.051 0.003) (0.010 0.002)
TYP. 3.56 0.13 (0.140 0.005) 4.70 (0.185) MAX.
0.51 (0.020) MIN. 2.92 (0.115) MIN. DIMENSIONS MILLIMETERS (INCHES). 1.080 0.320 (0.043 0.013) 0.65 (0.025) MAX. 2.54 0.25 (0.100 0.010) NOTE: FLOATING LEAD PROTRUSION mils) MAX.
Gull Wing Surface Mount Option
LAND PATTERN RECOMMENDATION 9.80 0.25 (0.386 0.010)
1.02 (0.040)
HCPL-J314 YYWW
6.350 0.25 (0.250 0.010)
10.9 (0.430)
MOLDED
1.27 (0.050)
(0.080)
1.19 (0.047) MAX.
1.780 (0.070) MAX.
9.65 0.25 (0.380 0.010) 7.62 0.25 (0.300 0.010)
3.56 0.13 (0.140 0.005)
0.255 (0.075) 0.010 (0.003)
1.080 0.320 (0.043 0.013) 2.540 (0.100) 0.51 0.130 (0.020 0.005)
0.635 0.25 (0.025 0.010)
NOM.
DIMENSIONS MILLIMETERS (INCHES). TOLERANCES (UNLESS OTHERWISE SPECIFIED): xx.xx 0.01 xx.xxx 0.005 NOTE: FLOATING LEAD PROTRUSION mils) MAX.
LEAD COPLANARITY MAXIMUM: 0.102 (0.004)
Solder Reflow Temperature Profile
PREHEATING RATE 1°C/-0.5°C/SEC. REFLOW HEATING RATE 2.5°C 0.5°C/SEC. PEAK TEMP. 245°C PEAK TEMP. 240°C PEAK TEMP. 230°C 2.5°C 0.5°C/SEC. 160°C 150°C 140°C 1°C/-0.5°C SEC. SEC. SOLDERING TIME 200°C
Regulatory Information
HCPL-J314 been approved following organizations: IEC/EN/DIN 60747-5-2 Approved under: 60747-5-2:1997 A1:2002 60747-5-2:2001 A1:2002 60747-5-2 (VDE 0884 Teil 2):2003-01 Approval under 1577, component recognition program VISO 3750 Vrms. File E55361. Approved under Component Acceptance Notice File 88324.
TEMPERATURE (°C)
PREHEATING TIME 150°C, SEC. SEC. TIGHT TYPICAL LOOSE
ROOM TEMPERATURE
TIME (SECONDS)
Recommended Pb-Free Profile
TIME WITHIN ACTUAL PEAK TEMPERATURE 20-40 SEC.
+0/-5 RAMP-UP °C/SEC. MAX.
TEMPERATURE
Tsmax Tsmin
RAMP-DOWN °C/SEC. MAX.
PREHEAT SEC. PEAK
SEC.
TIME NOTES: TIME FROM PEAK TEMPERATURE MINUTES MAX. Tsmax Tsmin
IEC/EN/DIN 60747-5-2 Insulation Characteristics
Description Installation classification 0110/1.89, Table rated mains voltage Vrms rated mains voltage Vrms rated mains voltage Vrms Climatic Classification Pollution Degree (DIN 0110/1.89) Maximum Working Insulation Voltage Input Output Test Voltage, Method IORM 1.875=V 100% Production Test with tm=1 sec, Partial discharge Input Output Test Voltage, Method IORM 1.5=VPR, Type Sample Test, tm=60 sec, Partial discharge Highest Allowable Overvoltage (Transient Overvoltage tini sec) Safety-limiting values maximum values allowed event failure. Case Temperature Input Current** Output Power** Insulation Resistance VIORM Symbol Characteristic I-II 55/100/21 1670 peak peak Unit
IO
1336 6000
peak peak
IS,INPUT OUTPUT
1200 >109
Refer optocoupler section Isolation Control Components Designer's Catalog, under Product Safety Regulations section, IEC/EN/DIN 60747-5-2 detailed description Method Method partial discharge test profiles. Refer following figure dependence ambient temperature.
OUTPUT POWER INPUT CURRENT
(mW) (mA)
CASE TEMPERATURE
Insulation Safety Related Specifications
Parameter Minimum External (Clearance) Minimum External Tracking (Creepage) Minimum Internal Plastic (Internal Clearance) Symbol L(101) HCPL-J314 Units Conditions Measured from input terminals output terminals, shortest distance through air. Measured from input terminals output terminals, shortest distance path along body. Through insulation distance conductor conductor, usually straight line distance thickness between emitter detector. 112/VDE 0303 Part Material Group (DIN 0110, 1/89, Table
L(102)
Tracking Resistance (Comparative Tracking Index) Isolation Group
>175 IIIa
Absolute Maximum Ratings
Parameter Storage Temperature Operating Temperature Average Input Current Peak Transient Input Current pulse width, 300pps) Reverse Input Voltage "High" Peak Output Current "Low" Peak Output Current Supply Voltage Output Voltage Output Power Dissipation Input Power Dissipation Lead Solder Temperature Solder Reflow Temperature Profile Symbol IF(AVG) IF(TRAN) IOH(PEAK) IOL(PEAK) CC-VEE VO(PEAK) -0.5 -0.5 Min. Max. Units Note
260°C sec., below seating plane Package Outline Drawings section
Recommended Operating Conditions
Parameter Power Supply Input Current (ON) Input Voltage (OFF) Operating Temperature Symbol -VEE IF(ON) VF(OFF) Min. -3.0 Max. Units Note
Electrical Specifications (DC)
Over recommended operating conditions unless otherwise specified. Parameter High Level Output Current Level Output Current High Level Output Voltage Level Output Voltage High Level Supply Current Level Supply Current Threshold Input Current High Threshold Input Voltage High Input Forward Voltage Temperature Coefficient Input Forward Voltage Input Reverse Breakdown Voltage Input Capacitance Symbol ICCH ICCL IFLH VFHL VF/TA Min. VCC-4 Typ. -1.8 Max. Units -1.6 mV/°C Test Conditions VCC-10 VEE+2.5 EE+10 -100 Vo>5 Fig. 9,15 Note
MHz,
Switching Specifications (AC)
Over recommended operating conditions unless otherwise specified. Parameter Propagation Delay Time High Output Level Propagation Delay Time Output Level Propagation Delay Difference Between Parts Channels Rise Time Fall Time Output High Level Common Mode Transient Immunity Output Level Common Mode Transient Immunity Symbol tPLH tPHL Min. -0.5 Typ. Max. Units Test Conditions kHz, Duty Cycle 50%, Fig. Note 10,11, 12,13, 14,17
|CMH| |CML
kV/µs kV/µs
25°C,
Package Characteristics
each channel unless otherwise specified. Parameter Input-Output Momentary Withstand Voltage Output-Output Momentary Withstand Voltage Input-Output Resistance Input-Output Capacitance Symbol VISO VO-O RI-O CI-O Min. 3750 1500 1012 Typ. Max. Units Vrms Vrms Test Conditions TA=25°C, RH<50% min. VI-O=500 Freq=1 Fig. Note
Notes: Derate linearly above 70°C free temperature rate mA/°C. Maximum pulse width maximum duty cycle 0.2%. This value intended allow component tolerances designs with peak minimum Application section additional details limiting peak. Derate linearly above 85°C, free temperature rate mW/°C. Input power dissipation does require derating. Maximum pulse width maximum duty cycle 0.5%. this test, measured with load current. When driving capacitive load will approach approaches zero amps. Maximum pulse width maximum duty cycle 20%. accordance with 1577, each HCPL-J314 optocoupler proof tested applying insulation test voltage 5000 Vrms second (leakage detection current limit II-O µA). This test performed before 100% production test partial discharge (method shown IEC/EN/DIN 60747-5-2 Insulation Characteristics Table, applicable. Device considered two-terminal device: pins input side shorted together pins output side shorted together. difference between tPHL tPLH between parts channels under same test conditions. Common mode transient immunity high state maximum tolerable |dVcm/dt| common mode pulse assure that output will remain high state (i.e. Common mode transient immunity state maximum tolerable |dVCM/dt| common mode pulse, assure that output will remain state (i.e. This load condition approximates gate load 1200 V/25 IGBT. each channel. power supply current increases when operating frequency driven IGBT increases. Device considered terminal device: Channel output side pins shorted together, channel output side pins shorted together.
(VOH-VCC) HIGH OUTPUT VOLTAGE DROP
0.40
OUTPUT HIGH CURRENT
(VOH-VCC) OUTPUT HIGH VOLTAGE DROP
-0.5
0.38
-1.0
0.36
-1.5
0.34
-2.0
0.32
-2.5
0.30
TEMPERATURE
TEMPERATURE
OUTPUT HIGH CURRENT
Figure Temperature.
Figure Temperature.
Figure IOH.
0.44
OUTPUT VOLTAGE
0.470 0.465 0.460 0.455 0.450 0.445 0.440
OUTPUT VOLTAGE
OUTPUT CURRENT
0.43
0.42
0.41
0.40
0.39
OUTPUT CURRENT
TEMPERATURE
TEMPERATURE
Figure Temperature.
Figure Temperature.
Figure
SUPPLY CURRENT
SUPPLY CURRENT
IFLH HIGH CURRENT THRESHOLD
ICCL ICCH
ICCL ICCH
TEMPERATURE
SUPPLY VOLTAGE
TEMPERATURE
Figure Temperature.
Figure VCC.
Figure IFLH Temperature.
PROPAGATION DELAY
PROPAGATION DELAY
PROPAGATION DELAY
TPLH TPHL
TPLH TPHL
SUPPLY VOLTAGE
FORWARD CURRENT
TEMPERATURE
Figure Propagation Delay VCC.
Figure Propagation Delay
Figure Propagation Delay Temperature.
PROPAGATION DELAY
PROPAGATION DELAY
OUTPUT VOLTAGE
TPLH TPHL
TPLH TPHL
SERIES LOAD RESISTANCE
LOAD CAPACITANCE
FORWARD CURRENT
Figure Propagation Delay
Figure Propagation Delay
Figure Transfer Characteristics.
FORWARD CURRENT
FORWARD VOLTAGE
Figure Input Current Forward Voltage.
DUTY CYCLE
VOUT tPLH tPHL
Figure Propagation Delay Test Circuit Waveforms.
SWITCH SWITCH 1500
Figure Test Circuit Waveforms.
Applications Information
Eliminating Negative IGBT Gate Drive keep IGBT firmly off, HCPL-J314 very maximum specification Minimizing lead inductance from HCPL-J314 IGBT gate emitter (possibly mounting HCPL-J314 small board directly above IGBT)
eliminate need negative IGBT gate drive many applications shown Figure Care should taken with such board design avoid routing IGBT collector emitter traces close HCPL-J314 input this result unwanted coupling transient signals into input HCPL-J314 degrade performance. IGBT
drain must routed near HCPL-J314 input, then should reverse biased when state, prevent transient signals coupled from IGBT drain from turning HCPL-J314.)
HCPL-J314
HVDC
CONTROL INPUT 74XXX OPEN COLLECTOR
3-PHASE
HVDC
Figure Recommended Drive Application Circuit HCPL-J314.
ENERGY SWITCHING CYCLE
Selecting Gate Resistor (Rg) Step Calculate minimum from peak specification. IGBT Figure analyzed simple circuit with voltage supplied HCPL-J314. IOLPEAK 0.6A
GATE RESISTANCE
value previous equation peak current 0.6A. (See Figure Step Check HCPL-J314 power dissipation increase necessary. HCPL-J314 total power dissipation (PT) equal emitter power (PE) output power (PO). Duty Cycle PO(BIAS) PO(SWITCHING) (ICCBIAS KICC (Rg,Qg) where KICC increase switching KICC constant 0.001 mA/(nC*kHz). circuit Figure with (worst case) Duty Cycle 80%, TAMAX 85°C: (0.001 mA/(nC kHz)) (PO(MAX) 85°C) value previous equation max. over entire operating temperature range. Since this case less than PO(MAX), alright power dissipation.
Figure Energy Dissipated HCPL-J314 Each IGBT Switching Cycle.
Drive Circuit Considerations Ultra High Performance
Without detector shield, dominant cause optocoupler failure capacitive coupling from input side optocoupler, through package, detector shown Figure HCPL-J314 improves performance using detector with optically transparent Faraday shield, which diverts capacitively coupled current away from sensitive circuitry. However, this shield does eliminate capacitive coupling between optocoupler pins shown Figure This capacitive coupling causes perturbations current during common mode transients becomes major source failures shielded optocoupler. main design objective high drive circuit becomes keeping proper state during common mode transients. example, recommended application circuit (Figure 19), achieve kV/µs while minimizing component complexity. Techniques keep proper state discussed next sections.
CLEDP
CLEDO1 CLEDP
CLEDO2
CLEDN
CLEDN
SHIELD
Figure Optocoupler Input Output Capacitance Model Unshielded Optocouplers.
Figure Optocoupler Input Output Capacitance Model Shielded Optocouplers.
CLEDP
ILEDP
VSAT
CLEDN
SHIELD
ARROWS INDICATE DIRECTION CURRENT FLOW DURING -dVCM/dt.
Figure Equivalent Circuit Figure During Common Mode Transient.
CLEDP
CLEDP
CLEDN ILEDN
CLEDN
SHIELD
SHIELD
Figure Recommended Open Collector Drive Circuit.
Figure Recommended Drive Circuit Ultra-High Dead Time Propagation Delay Specifications.
with (CMRH) high drive circuit must keep during common mode transients. This achieved overdriving current beyond input threshold that pulled below threshold during transient. minimum current provides adequate margin over maximum IFLH achieve kV/µs CMR. with (CMRL) high drive circuit must keep VF(OFF)) during common mode transients. example, during -dVCM/dt transient Figure current flowing through CLEDP also flows through RSAT logic gate. long state voltage developed across logic gate less than VF(OFF) will remain common mode failure will occur. open collector drive circuit, shown Figure keep during CM/dt transient, since current flowing through CLEDN must
supplied LED, recommended applications requiring ultra high CMR1 performance. alternative drive circuit which like recommended application circuit (Figure 19), does achieve ultra high performance shunting state. Dead Time Propagation Delay Specifications HCPL-J314 includes Propagation Delay Difference (PDD) specification intended help designers minimize "dead time" their power inverter designs. Dead time time high side power transistors off. overlap conduction will result large currents flowing through power devices from high-voltage lowvoltage motor rails. minimize dead time given design, turn LED2 should delayed (relative turn LED1) that under worstcase conditions, transistor just turned when transistor turns shown Figure amount
delay necessary achieve this condition equal maximum value propagation delay difference specification, max, which specified over operating temperature range -40° 100°C. Delaying signal maximum propagation delay difference ensures that minimum dead time zero, does tell designer what maximum dead time will maximum dead time equivalent difference between maximum minimum propagation delay difference specification shown Figure maximum dead time HCPL-J314 (-0.5 µs)) over operating temperature range -40°C 100°C. Note that propagation delays used calculate dead time taken equal temperatures test conditions since optocouplers under consideration typically mounted close proximity each other switching identical IGBTs.
ILED1
VOUT1
VOUT2 ILED2
tPHL tPLH PDD* (tPHL- tPLH)MAX tPHL tPLH
*PDD PROPAGATION DELAY DIFFERENCE NOTE: CALCULATIONS PROPAGATION DELAYS TAKEN SAME TEMPERATURE TEST CONDITIONS.
Figure Minimum Skew Zero Dead Time.
ILED1
VOUT1
VOUT2
ILED2 tPHL tPHL tPLH
tPLH (tPHL-tPLH) PDD* MAXIMUM DEAD TIME (DUE OPTOCOUPLER) (tPHL tPHL MIN) (tPLH tPLH MIN) (tPHL tPLH MIN) (tPHL tPLH MAX) PDD* PDD* *PDD PROPAGATION DELAY DIFFERENCE NOTE: DEAD TIME CALCULATIONS PROPAGATION DELAYS TAKEN SAME TEMPERATURE TEST CONDITIONS.
Figure Waveforms Dead Time.
www.agilent.com/semiconductors
product information complete list distributors, please site. technical assistance call: Americas/Canada: (800) 235-0312 (916) 788-6763 Europe: 6441 92460 China: 10800 0017 Hong Kong: (+65) 6756 2394 India, Australia, Zealand: (+65) 6755 1939 Japan: (+81 3335-8152 (Domestic/International), 0120-61-1280 (Domestic Only) Korea: (+65) 6755 1989 Singapore, Malaysia, Vietnam, Thailand, Philippines, Indonesia: (+65) 6755 2044 Taiwan: (+65) 6755 1843 Data subject change. Copyright 2005 Agilent Technologies, Inc. Obsoletes 5989-0311EN March 2005 5989-2140EN

HCPL-J314 Minimum Peak Output Current High Speed Response: Max. P

Top Searches for this datasheet

Other recent searches