XR88C92/192 XR88C92 XR88C192 SC26C92 SCC2692 XR88C92CP XR88C92CJ XR88C92CV - Datasheet Archive

 

DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER May 2000 DESCRIPTION The XR88C92/192 is a Dual Universal Asynchronous

 

XR88C92/192 XR88C92/192 DUAL UNIVERSAL ASYNCHRONOUS RECEIVER AND TRANSMITTER May 2000 DESCRIPTION The XR88C92/192 XR88C92/192 is a Dual Universal Asynchronous Receiver and Transmitter with 8 (XR88C92 XR88C92) / 16 (XR88C192 XR88C192) bytes transmit and receive FIFO. The XR88C92/192 XR88C92/192 is a pin and functional replacement for the SC26C92 SC26C92 and an improved version of the Philips SCC2692 SCC2692 UART with additional features. The operating speed of the receiver and transmitter can be selected independently from a table of eighteen fixed baud rates, a 16X clock derived from a programmable counter/timer, or an external 1X or 16X clock. The baud rate generator and counter/timer can operate directly from a crystal or from external clock input. The XR88C92/192 XR88C92/192 provides a power-down mode in which the oscillator is stopped but the register contents are retained. The XR88C92/192 XR88C92/192 is fabricated in an advanced CMOS process to achieve low power and high speed requirements. FEATURES IP4 IP5 IP6 IP2 43 42 41 40 A0 2 VCC IP3 3 N.C. A1 1 IP1 4 44 A2 5 A3 7 39 -C S IP 0 8 38 R ESET -IO W 9 37 XTAL2 -IO R 10 36 XTAL1 R XB 11 35 R XA 34 N .C . 33 TXA X R 88C 92 X R 88C 192 30 OP4 17 29 OP6 D0 28 16 OP7 D2 27 OP5 D4 26 OP2 D6 25 OP0 31 -INT 24 32 15 N.C. 23 14 OP3 D7 21 OP1 GND 22 13 D5 20 12 TXB D3 19 N .C . D1 18 ·Pin to pin and functional compatible to SC26C92 SC26C92 and SCC2692 SCC2692 ·Full duplex asynchronous transmit receive operation ·8 Bytes transmit/receive FIFO (XR88C92 XR88C92) ·16 Bytes transmit/receive FIFO (XR88C192 XR88C192) ·Programmable character lengths (5, 6, 7, 8) ·Parity, framing, and over run error detection ·Programmable 16-bit timer/counter ·On-chip crystal oscillator ·Single interrupt output with eight selectable interrupt ing conditions ·External 1X or 16X clock ·Data rate up to 1Mbps ·Selectable baud rates from 50bps to 230.4kbps ·7 General purpose inputs ·8 General purpose outputs ·TTL compatible inputs, outputs ·4 Transmit/receive trigger levels ·Watch dog timer ·Multidrop mode operation ·3.3 or 5 volts operation ·Loopback modes ·Power down mode 6 PLCC Package ORDERING INFORMATION Part number Pins XR88C92CP XR88C92CP XR88C92CJ XR88C92CJ XR88C92CV XR88C92CV XR88C92IP XR88C92IP XR88C92IJ XR88C92IJ XR88C92IV XR88C92IV 40 44 44 40 44 44 Package Operating temperature PDIP PLCC TQFP PDIP PLCC TQFP 0° C 0° C 0° C -40° C -40° C -40° C to + 70° C to + 70° C to + 70° C to + 85° C to + 85° C to + 85° C Part number XR88C192CP XR88C192CP XR88C192CJ XR88C192CJ XR88C192CV XR88C192CV XR88C192IP XR88C192IP XR88C192IJ XR88C192IJ XR88C192IV XR88C192IV Pins 40 44 44 40 44 44 Package Operating temperature PDIP PLCC TQFP PDIP PLCC TQFP 0° C 0° C 0° C -40° C -40° C -40° C to + 70° C to + 70° C to + 70° C to + 85° C to + 85° C to + 85° C Rev. 1.10 EXAR Corporation, 48720 Kato Road, Fremont, CA 94538 · (510) 668-7000 · FAX (510) 668-7017 XR88C92/192 XR88C92/192 Package Description A2 IP1 A1 IP3 A0 VCC VCC IP4 IP5 IP6 IP2 43 42 41 40 39 38 37 36 35 34 44 Pin TQFP Package 44 40 Pin DIP Package A0 1 40 VCC IP 3 2 39 IP 4 A1 3 38 IP 5 IP 1 4 37 IP 6 A3 1 33 -C S IP 2 IP 0 2 32 RESET -IO W 3 31 X T A L2 -IO R 4 30 X T A L1 RXB 5 29 RXA A2 A3 IP 0 5 36 6 35 7 34 -C S RESET 33 XTAL2 32 XTAL1 31 RXA 30 12 OP3 -IO W 8 -IO R 9 RXB 10 TXB 11 OP1 X R 88 C 92 X R 88 C 19 2 OP5 14 27 OP4 OP7 15 26 OP6 D1 16 25 D0 D3 17 24 D2 D5 18 23 D4 D7 19 22 D6 GND 20 21 -IN T Rev. 1.10 2 22 N .C . 21 23 D0 11 D2 N .C . D4 OP2 20 28 19 OP6 13 D6 24 18 10 -INT OP7 17 OP0 GND OP4 29 16 25 GND 9 15 OP5 D7 OP2 TXA 14 26 D5 8 13 OP0 OP3 12 TXA 27 D3 28 7 D1 6 XR88C92 XR88C92 XR88C192 XR88C192 TXB OP1 XR88C92/192 XR88C92/192 T ran sm it F IF O R eg isters Data bus & Control Logic -IN T T ran sm it S h ift R eg ister T X A /B R eceive S h ift R eg ister R X A /B F low C on trol L og ic Inter Connect Bus Lines & Control signals A 0-A 3 -C S Interrupt Control Logic D 0-D 7 -IO R -IO W RESET Register Select Logic Block Diagram R eceive F IF O R eg isters F low C on trol L og ic O P 0-O P 7 XTAL2 Clock & Baud Rate Generator XTAL1 I/O C on trol L og ic Rev. 1.10 3 IP 0-IP 6 XR88C92/192 XR88C92/192 SYMBOL DESCRIPTION (* 44 pin TQFP) Symbol 44 Pin 40 44* Signal type Pin Description RX A/B 35,11 31,10 29,5 I Serial data input. The serial information (data) received from serial port to XR88C92/192 XR88C92/192 receive input circuit. A mark (high) is logic one and a space (low) is logic zero. TX A/B 33,13 30,11 28,6 O Serial data output. The serial data is transmitted via this pin with additional start , stop and parity bits. The TX will be held in mark (high) state during reset, local loop back mode or when the transmitter is disabled. RESET 38 34 32 I Master reset. (active high) A high on this pin will reset all the outputs and internal registers. The transmitter output and the receiver input will be disabled during reset time. OP0 32 29 27 O Multi-purpose output. General purpose output or Channel A Request-To-Send (-RTSA active low). OP1 14 12 7 O Multi-purpose output. General purpose output or Channel B Request-To-Send (-RTSB active low). OP2 31 28 26 O Multi-purpose output. General purpose output or one of the following functions can be selected for this output pin by programming the Output Port Confiuration Register bits 1,0; TxAClk1 -Transmit 1X clock. TxAClk16 -Transmit 16X clock RxAClk1 -Receive 1X clock OP3 15 13 8 O Multi-purpose output. General purpose output or one of the following functions can be selected for this output pin by programming the Output Port Confiuration Register bits 3,2; C/T -Counter timer output (Open drain output) TxBClk1 -Transmit 1X clock RxBClk1 -Receive 1X clock OP4 30 27 25 O Multi-purpose output. General purpose output or one of the following functions can be selected for this output pin by programming the Output Port Confiuration Register bit 4; -RxARDY -Receive ready signal (Open drain output) -RxAFULL - Receive FIFO full signal (Open drain output) Rev. 1.10 4 XR88C92/192 XR88C92/192 SYMBOL DESCRIPTION (* 44 pin TQFP) Symbol 44 OP5 Pin 40 44* Signal type 16 14 9 O Pin Description Multi-purpose output. General purpose output or one of the following functions can be selected for this output pin by programming the Output Port Confiuration Register bit 5; -RxBRDY - Receive ready signal (Open drain output) -RxBFULL - Receive FIFO full signal (Open drain output) OP6 29 26 24 O Multi-purpose output. General purpose output or Transmit A holding register empty interrupt (-TxARDY Open drain output). OP7 17 15 10 O Multi-purpose output. General purpose output or Transmit B holding register empty interrupt (-TxBRDY Open drain output) 2,4, 6,7 1,3, 5,6 40,42, 44,1 I Address select lines. To select internal registers. XTAL1 36 32 30 I Crystal input 1 or external clock input. A crystal can be connected to this pin and XTAL2 pin to utilize the internal oscillator circuit. An external clock can be used to clock internal circuit and baud rate generator for custom transmission rates. XTAL2 37 33 31 O Crystal input 2 or buffered clock output. See XTAL1. GND 22 20 16,17 Pwr -INT 24 21 18 O Interrupt output (open drain active low) This pin goes low upon occurrence of one or more of eight maskable interrupt conditions (when enabled by the interrupt mask register). CPU can read the interrupt status register to determine the interrupting condition(s). This output requires a pull-up resistor. IP0 8 7 2 I Multi-purpose input or Channel A Clear-To-Send (-CTSA active low). IP1 5 4 43 I Multi-purpose input or Channel B Clear-To-Send (-CTSB active low). IP2 40 36 34 I Multi-purpose input or Timer/Counter External clock input. IP3 3 2 41 I Multi-purpose input or Channel A transmit external clock port A0-A3 Signal and power ground. Rev. 1.10 5 XR88C92/192 XR88C92/192 SYMBOL DESCRIPTION (* 44 pin TQFP) Symbol 44 Pin 40 44* Signal type Pin Description input. The transmit data is clocked on the falling edge of the clock. IP4 43 39 37 I Multi-purpose input or Channel A receive external clock input. The transmit data is clocked on the rising edge of the clock. IP5 42 38 36 I Multi-purpose input or Channel B Transmit external clock input. The transmit data is clocked on the falling edge of the clock. IP6 41 37 35 I Multi-purpose input or Channel B receive external clock input. The transmit data is clocked on the rising edge of the clock. -CS 39 35 33 I Chip select (active low). A low at this pin enables the serial port / CPU data transfer operation. 28,18 27,19 26,20 25,21 25,16 24,17 23,18 22,19 22,12 21,13 20,14 19,15 -IOW 9 8 3 I Write strobe (active low). A low on this pin will transfer the contents of the CPU data bus to the addressed register. -IOR 10 9 4 I Read strobe (active low). A low on this pin will transfer the contents of the XR88C92/192 XR88C92/192 register to CPU data bus. VCC 44 40 38,39 Pwr N.C. 1,12 23,34 D0-D7 11,23 I/O Bi-directional data bus. Eight bit, three state data bus to transfer information to or from the CPU. D0 is the least significant bit of the data bus and the first serial data bit to be received or transmitted. Power supply input. No Connection. Rev. 1.10 6 XR88C92/192 XR88C92/192 INTERNAL CONTROL LOGIC register and C/T lower register and produces an interrupt. This is a system-oriented feature that can be used to record timeouts when implementing various application protocols. The internal control logic receives operation commands from the central processing unit (CPU) and generates appropriate signals to the internal sections to control device operation. The internal control logic allows access to the registers within the XR88C92/192 XR88C92/192 and performs various commands by decoding the four register-select lines (A0 through A3). Besides the four register-select lines, there are four other inputs to the internal control logic from the -IOR (read), -IOW (write), which allow read and write transfers between the CPU and XR88C92/192 XR88C92/192 via the data bus buffer; -CS (chipselect), which is the XR88C92/192 XR88C92/192 chip-select; and RESET (reset), which initializes or resets. INTERRUPT CONTROL LOGIC The following registers are associated with the interrupt control logic: · Interrupt Mask Register (IMR) · Interrupt Status Register (ISR) · Auxiliary Control Register (ACR) A single active-low interrupt output (-INT) can notify the processor that any of eight internal events has occurred. These eight events are described in the discussion of the interrupt status register (ISR). User can program the interrupt mask register (IMR) to allow only certain conditions to cause -INT to be asserted while the CPU can read the ISR to determine all currently active interrupting conditions. In addition, users can program the parallel outputs OP3 through OP7 to provide discrete interrupt outputs for the transmitters, the receivers, and the C/T. TIMING LOGIC The timing logic consists of a crystal oscillator, a baud rate generator (BRG), a programmable 16-bit counter/ timer (C/T), and four clock selectors. The crystal oscillator operates directly from a 3.6864 MHz crystal connected across the XTAL1 and XTAL2 inputs or from an external clock of the appropriate frequency connected to XTAL1. The XTAL1 clock serves as the basic timing reference for the baud rate generator, the C/T, and other internal circuits. DATA BUS BUFFER The data bus buffer provides the interface between the external and internal data buses. It is controlled by the internal control logic to allow read and write data transfer operations to occur between the controlling CPU and XR88C92/192 XR88C92/192 by way of the eight parallel data lines (D0 through D7). The baud rate generator operates from the XTAL1 clock input and can generate 28 commonly used data communication baud rates ranging from 50 to 230.4k by producing internal clock outputs at 16 times the actual baud rate. The C/T can produce a 16X clock for other baud rates by counting down its programmed clock source. Other baud rates can also be derived by connecting 16X or 1X clocks to certain input port pins that have alternate functions as receiver or transmitter clock inputs. Four clock selectors allow the independent selection of any of these baud rates for each receiver and transmitter. Users can program the 16 bit C/T within the XR88C92/192 XR88C92/192 to use one of several clock sources as its input. The output of the C/T is available to the internal clock selectors and can also be programmed to appear at parallel output OP3. In the timer mode, the C/T acts as a programmable divider and can generate a square-wave output at OP3. In the counter mode, the C/T can be started and stopped under program control. When stopped, the CPU can read its contents. The counter counts down the number of pulses stored in the concatenation of the C/T upper COMMUNICATION CHANNELS A AND B Each communication channel includes a full-duplex asynchronous receiver/transmitter (UART). The operating frequency for each receiver and each transmitter can be selected independently from the baud rate generator, the C/T, or from an external clock. The transmitter accepts parallel data from the CPU, converts it to a serial bit stream, inserts the appropriate start, stop, and optional parity bits, and outputs a composite serial stream of data on the TX output pin. The receiver accepts serial data on the RX pin, converts this serial input to parallel format, checks for a start bit, stop bit, parity bit (if any), or break condition, and transfers an assembled character to the CPU during read operations. Rev. 1.10 7 XR88C92/192 XR88C92/192 INPUT PORT The CPU reads the inputs to this 7-bit port (IP0 through IP6). High or low inputs to the input port result in the CPU reading a logic one or logic zero, respectively. Each input port bit also has an alternate control function capability. The alternate functions can be enabled/ disabled on a bit-by-bit basis. 1 Four change-of-state detectors are associated with inputs IP0, IP1, IP2, and IP3. If a high-to-low or low-tohigh transition occurs on any of these inputs and the new level is stable for more than 25 to 50 microseconds (best-to-worst case times), the corresponding bit in the input port change register (IPCR) will be set. The sampling clock of the change detectors is the XTAL1/96 XTAL1/96 tap of the baud rate generator, which is 38.4kHz if XTAL1 is 3.6864MHz. A new input level must be sampled on two consecutive sample clocks to produce a change detect. Also, users can program the XR88C92/192 XR88C92/192 to allow a change of state to generate an interrupt to the CPU. The IPCR bits are cleared when the CPU reads the register. If an external CMOS-level clock is used, this pin must be left open. NOTE: The terms assertion and negation will be used extensively to avoid confusion when dealing with a mixture of "active low" and "active high" signals. The term assert or assertion indicates that a signal is active or true, independent of whether that level is represented by a high or low voltage. The term negate or negation indicates that a signal is inactive or false. RESET (RESET) The XR88C92/192 XR88C92/192 can be reset by asserting the RESET signal or by programming the appropriate command register. A hardware reset (assertion of RESET) clears the following registers: · · · · · OUTPUT PORT The 8 output pins can either be used as a general purpose output port or can be controlled using internal registers to generate signals representing various conditions. Associated with the output port is an output port register (OPR) that can be bit-wise programmed. A bit is set (logical 1) by performing a write operation at address 0xE with the data having that bit-location to be 1 (0 means no change). Similarly, a bit is reset (logical 0) by performing a write operation at address 0xF with the data having that bit-location as 1 (0 means no change). However, it is to be noted that the outputs are complements of the data contained in the OPR (eg., 0x05 in OPR actually means 0xFA at the output pins). Status registers A and B (SRA and SRB) Interrupt mask register (IMR) Interrupt status register (ISR) Output port register (OPR) Output port configuration register (OPCR) RESET performs the following operations: · Places parallel outputs OP0 through OP7 in the high state · Places the counter/timer in timer mode · Places channels A and B in the inactive state with the transmitter serial-data outputs (TXA and TXB) in the mark (high) state. XTAL1 Besides general-purpose outputs, the outputs can be individually assigned specific auxiliary functions serving the communication channels. The assignment is accomplished by appropriately programming the channel A and B mode registers (MR0A, MR0B, MR1A, MR1B, MR2A, and MR2B) and the output port configuration register (OPCR). XTAL2 X1 3.6863MHz C1 22pF CRYSTAL INPUT (XTAL2) If a crystal is used, it is connected between XTAL1 and this input, in which case a capacitor of approximately 15 to 33 pF should be connected from this pin to ground. C2 33pF Figure 1: Crystal Connection Rev. 1.10 8 XR88C92/192 XR88C92/192 Software resets are not as encompassing and are achieved by appropriately programming the channel A and/or B command registers. Reset commands can be programmed through the command register to reset the receiver, transmitter, error status, or break-change interrupts for each channel CHANNEL A/B RECEIVER SERIAL-DATA INPUT (RXA/RXB) The independent receiver serial-data inputs for channel A and B receive the least-significant bit first. Data on these pins is sampled on the rising edge of the programmed clock source. CHIP-SELECT (-CS) This active-low input signal, when low, enables data transfers between the CPU and XR88C92/192 XR88C92/192 on the data lines (D0 through D7). These data transfers are controlled by read (-IOR), write (-IOW) and the registerselect inputs (A0 through A3). When chip-select is high, the D0 through D7 data lines are placed in the highimpedance state. INPUT PORTS (IP0­IP6) The input ports can be used as general-purpose inputs. However, each pin also has an alternate function(s) described below: IP0 This input can be used as the channel A clear-to-send active-low input (-CTSA). A change-of-state detector is also associated with this input. 2 IP1 This input can be used as the channel B clear-to-send active-low input (-CTSB). A change-of-state detector is also associated with this input. READ (-IOR) When low, this input indicates a read cycle. Assertion of the chip-select input initiates a cycle. WRITE (-IOW) When low, this input indicates a write cycle. Assertion of the chip-select input initiates a cycle. 2 REGISTER-SELECT BUS (A0­A3) The register-select bus lines during read/write operations select the XR88C92/192 XR88C92/192 internal registers, ports, or commands. IP2 This input can be used as the counter/timer external clock input. A change-of-state detector is also associated with this input. IP3 This input can serve as the channel A transmitter external clock input (TxAClk1). When this input functions as the external clock to the transmitter, the transmitted data is clocked on the falling edge of the clock. A change-of-state detector is also associated with this input. DATA BUS (D0­D7) These bi-directional three-state data lines transfer commands, data, and status between the CPU and XR88C92/192 XR88C92/192. D0 is the least-significant bit. INTERUPT REQUEST (-INT) This active-low, open-drain output signals the CPU that one or more of the eight mask-able interrupting conditions are true. IP4 This input can be used as the channel A receiver external clock input (RxAClk1). When this input functions as the external clock to the receiver, the received data is sampled on the rising edge of the clock. CHANNEL A/B TRANSMITTER SERIAL-DATA OUTPUT (TXA/TXB) The independent transmitter serial-data outputs for channel A and B transmit the least-significant bit first. The output is held high (mark condition) when its associated transmitter is disabled, idle, or operating in the local loopback mode. ("Mark" is high and "space" is low.) Data is shifted out from this pin on the falling edge of the programmed clock source. IP5 This input can serve as the channel B transmitter external clock (TxBClk1). When this input is used as the external clock to the transmitter, the transmitted data is clocked on the falling edge of the clock. IP6 This input can serve as the channel B receive external clock (RxBClk1). When this input is used as the Rev. 1.10 9 XR88C92/192 XR88C92/192 external clock to the transmitter, the transmitted data is clocked on the rising edge of the clock. lected using bit-6 of MRB1. OP6 This output can function as the channel A open-drain active-low transmitter-ready interrupt output (TxARDY). OUTPUT PORTS (OP0­OP7) The output ports can be used as general-purpose outputs however, each pin also has an alternate function(s), described below; OP7 This output can serve as the channel B open-drain active-low transmitter-ready interrupt output (TxBRDY). OP0 This output can function as the channel A transmitter active-low request-to-send (-RTSA) output, or as the channel A receiver active-low request-to-send (-RTSA) output. This pin, if asserted by programming the corresponding bit in OPCR, is used by the transmitter (MRA2 bit-5 = 1) to indicate end of transmission by negating it. This is useful because, even when a command to disable the transmitter is sent before the data is fully transmitted, the transmitter sends all the data, negates OP0 and then gets disabled. When used by the receiver (MRA1 bit-7 = 1), this pin is automatically negated and reasserted depending on the FIFO space available. TRANSMITTER The channel A and B transmitters are enabled for data transmission through their respective command registers. The XR88C92/192 XR88C92/192 signals the CPU that it is ready to accept a character by setting the transmitter-ready bit in the channels status register. Users can program this condition to generate an interrupt request on the INT output, an interrupt request for channel A's transmitter on parallel output OP6, or for channel B's transmitter on parallel output OP7. When a character is loaded into the transmit buffer,the above condition for the respective channel is negated. Data is transferred from the transmit holding register to the transmit shift register when the shift register is idle or has completed transmission of the previous character. The transmitter ready conditions are then reasserted, providing one full character time of buffering. Characters cannot be loaded into the transmit buffer while the transmitter is disabled. OP1 This output is identical to OP0 and is meant for channel B of the DUART. 2 OP2 This output can be programmed (bits 0 & 1 of OPCR) to represent the channel A transmitter 1X-clock or 16Xclock output or the channel A receiver 1X-clock output. The transmitter converts the parallel data from the CPU to a serial bit stream on the transmitter serial-data output pin. It automatically sends a start bit followed by the programmed number of data bits, an optional parity bit, and the programmed number of stop bits. The leastsignificant bit is sent first. Data is shifted out the transmit serial data output pin on the falling edge of the programmed clock source. After the transmission of the stop bits, and a new character is not available in the transmit holding register, the transmitter serial-data output remains high and the transmitter-empty bit in the status register (SRA and SRB) will be set to one. Transmission resumes and the transmitter-empty bit is cleared when the CPU loads a new character into the transmit buffer. If the transmitter receives a disable command, it will continue operating until the character in the transmit shift register is completely sent out. Other characters in the holding register are neither sent nor discarded, but will be sent when the transmitter is re-enabled. Users can program the transmitter to automatically negate the request-to-send (RTS) output (al- OP3 This output can be used (when bits 2 & 3 of OPCR are programmed) as the open-drain active-low counterready output, the open-drain timer output, the channel B transmitter 1X-clock output, or the channel B receiver 1X-clock output. OP4 This output, when programmed using bit-4 of OPCR, can serve as the channel A open-drain active-low receiver-ready or buffer-full interrupt outputs (RxARDY/ RxAFULL). One of RxARDY or RxAFULL can be selected using bit-6 of MRA1. OP5 This output, when programmed using bit-5 of OPCR, can be used as the channel B open-drain active-low receiver-ready or buffer-full interrupt outputs (RxBRDY/ RxBFULL). One of RxBRDY or RxBFULL can be se- Rev. 1.10 10 XR88C92/192 XR88C92/192 sampled on the rising edge of the programmed clock source. ternate function of OP0 and OP1) on completion of a message transmission. If the transmitter is programmed to operate in this manner, the RTS output must be manually asserted before each message is transmitted. If OP0 (or OP1) is programmed in automatic RTS mode, the RTS output will be automatically negated when the transmitter is disabled and the transmit-shift register and holding register are both empty. In automatic RTS mode, a character in the holding register is not held back by a disable, but no more characters can be written to the holding register after the transmitter is disabled. During this process, the least-significant bit is received first. The data is then transferred to a receive holding register (RHR) and the receiver-ready bit in the status register (SRA or SRB) is set to one. This condition can be programmed to generate an interrupt request on the -INT output, an interrupt request for channel A receiver on output pin( OP4), or an interrupt request for channel B receiver on output pin (OP5). If the character length is less than eight bits, the most significant unused bits in the receive holding register (RHR) are set to zero. If clear-to-send (CTS) operation is enabled, the CTS input (alternate function of IP0 or IP1) must be low in order for the character to be transmitted. If it goes high in the middle of a transmission, the character in the shift register is transmitted and TX then remains in the marking state until CTS again goes low. The transmitter can also be forced to send a continuous low condition by issuing a send-break command. The state of CTS is ignored by the transmitter when it is set to send break. A send break is deferred as long as the transmitter has characters to send, but if normal character transmission is inhibited by CTS, the send-break will proceed. The send-break must be terminated by a stop-break, disable, or reset before normal character transmission can resume. If the stop bit is sampled as a 1, the receiver will immediately look for the next start bit. However, if the stop bit is sampled as a 0, either a framing error or a received break has occurred. If the stop bit is 0 and the data and parity (if any) are not all zero, it is a framing error, the damaged character is transferred to a holding register with the framing error flag set. If the receiver serial data remains low for one-half of the bit period after the stop bit was sampled, the receiver operates as if a new start bit transition has been detected. If the stop bit is 0 and the data and parity (if any) are also all zero, it is a break. A character consisting of all zeros will be loaded into a receive holding register (RHR) with the received-break bit (but not the framing error bit) set to one. The receiver serial-data input must return to a high condition for at least one-half bit time before a search for the next start bit begins. The transmitter can be reset through a software command. If it is reset, operation ceases immediately and must be enabled through the command register before resuming operation. Reset also discards any character in the holding register. The receiver can detect a break that starts in the middle of a character provided the break persists completely through the next character time or longer. When the break begins in the middle of a character, the receiver will place the damaged character in a holding register with the framing error bit set. Then, provided the break persists through the next character time, the receiver will also place an all-zero character in the next holding register with the received-break bit set. The parity error, framing error, overrun error, and received-break conditions (if any) set error and break flags in the status register at the received character boundary and are valid only when the receiver-ready bit (RXRDY) in the status register is set. A first-in first-out (FIFO) stack is used in each channels receive buffer logic and consists of 8 (16 for XR88C192 XR88C192) receive holding registers. RECEIVER The channel A and B receivers are enabled for data reception through the respective channels command register. The channels receiver looks for the high-to-low (mark-to-space) transition of a start bit on the receiver serial-data input pin. If operating in 16X clock mode, the serial input data is re-sampled on the next 7 clocks. If the receiver serial data is sampled high, the start bit is invalid and the search for a valid start bit begins again. If receiver serial data is still low, a valid start bit is assumed and the receiver continues to sample the input at one bit time intervals (at the theoretical center of the bit) until the proper number of data bits and the parity bit (if any) have been assembled and one stop bit has been detected. Data on the receiver serial data input pin is The receiver buffer is composed of the FIFO and a Rev. 1.10 11 XR88C92/192 XR88C92/192 receive shift register connected to the receiver serialdata input. Data is assembled in the shift register and loaded into the top most empty FIFO receive holding register position. The receiver-ready bit in the status register (SRA or SRB) is set whenever one or more characters are available to be read. A read of the receiver buffer produces an output of data from the top of the FIFO stack. After the read cycle, the data at the top of the FIFO stack and its associated status bits are "popped" and new data can be added at the bottom of the stack by the receive shift register. The FIFO-full status bit is set if all eight stack positions are filled with data. Either the receiver-ready or the FIFO-full status bits can be selected to cause an interrupt. In addition to the data byte, three status bits (parity error, framing error, and received break) are appended to each data character in the FIFO (overrun is not). By programming the errormode control bit in the channels mode register, status can be provided for "character" or "block" modes. Reading the status register (SR) does not affect the FIFO. The FIFO is "popped" only when the receive buffer is read. If all 8/16 of the FIFO's receive holding registers are full when a new character is received, that character is held in the receive shift register until a FIFO position is available. If an additional character is received while this state exists, the contents of the FIFO are not affected, but the character previously in the shift register is lost and the overrun-error status bit will be set upon receipt of the start bit of the new overrunning character. To support flow control, a receiver can automatically negate and reassert the request-to-send (RTS) output (alternate function of output ports OP0 and OP1). The request-to-send output will automatically be negated by the receiver when a valid start bit is received and the FIFO stack is full. When a FIFO position becomes available, the request-to-send output will be reasserted automatically by the receiver. Connecting the requestto-send output to the clear-to send (CTS) input of a transmitting device, prevents overrun errors in the receiver. The RTS output must be manually asserted the first time. Thereafter, the receiver will control the RTS output. In the "character" mode, the status register (SRA or SRB) is updated on a character-by-character basis and applies only to the character at the top of the FIFO. Thus, the status must be read before the character is read. Reading the character pops it and its error flags off the FIFO. In the "block" mode, the status provided in the status register for the parity error, framing error, and received-break conditions are the logical OR of these respective bits, for all characters coming to the top of the FIFO stack since the last reset error command was issued. That is, beginning at the last reset-error command issued, a continuous logical-OR function of corresponding status bits is produced in the status register as each character comes to the top of the FIFO stack. If the FIFO stack contains characters and the receiver is then disabled, the characters in the stack can still be read but no additional characters can be received until the receiver is again enabled. If the receiver is disabled while receiving a character, or while there is a character in the shift register waiting for a FIFO opening, these characters are lost. If the receiver is reset, the FIFO stack and all of the receiver status bits, the corresponding output ports, and the interrupt request are reset. No additional characters can be received until the receiver is again enabled. LOOPBACK MODES Besides the normal operation mode in which the receiver and transmitter operate independently, each XR88C92/192 XR88C92/192 channel can be configured to operate in various looping modes that are useful for local and remote system diagnostic functions. 3 AUTOMATIC ECHO MODE In this mode, the channel automatically retransmits the received data on a bit-by-bit basis. The local CPU-toreceiver communication continues normally but the CPU-to-transmitter link is disabled. The block mode is useful in applications requiring the exchange of blocks of information where the software overhead of checking each characters error flags cannot be tolerated. In this mode, entire messages can be received and only one data integrity check is performed at the end of each message. Although data reception in this manner has speed advantages, there are also disadvantages. Because each character is not individually checked for error conditions by the software, if an error occurs within a message the error will not be recognized until the final check is performed. Also, there is no indication of which character(s) is in error within the message. 3 Rev. 1.10 12 XR88C92/192 XR88C92/192 LOCAL LOOPBACK MODE In this mode, the transmitter output is internally connected to the receiver input. The external TX pin is held in the mark (high) state in this mode. This mode is useful for testing the operation of a local XR88C92/192 XR88C92/192 channel. By sending data to the transmitter and checking that the data assembled by the receiver is the same data that was sent, proper channel operation can be assured. In this mode the CPU-to-transmitter and CPUto-receiver communications continue normally. address character or a data character. The character is interpreted as an address character if the A/D bit is set to a one or interpreted as a data character if it is set to a zero. The polarity of the transmitted address/data bit is selected by programming bit two in mode register one (MR1) to a '1' for an address character and to a '0' for data characters. Users should program the mode register prior to loading the corresponding data or address characters into the transmit buffer. 3 In the Multidrop mode, the receiver continuously monitors the received data stream regardless of whether it is enabled or disabled. If the receiver is disabled, it sets the receiver ready status bit and loads the character into the FIFO receive holding register stack provided the received address/data bit is a one (address tag). The received character is discarded if the received address/ data bit is a zero (data tag). If the receiver is enabled, all received characters are transferred to the CPU by way of the receive holding register stack during read operations. In either case, the data bits are loaded into the data portion of the FIFO stack while the address/data bit is loaded into the status portion of the FIFO stack normally used for parity error (status register bit five). Framing error, overrun error, and break-detection operate normally regardless of whether the receiver is enabled or disabled. The address/data bit takes the place of the parity bit and parity is neither calculated nor checked for characters in this mode. REMOTE LOOPBACK MODE In this mode, the channel automatically retransmits the received data on a bit-by-bit basis. The local CPU-toreceiver and CPU-to-transmitter links are disabled. This mode is useful in testing the receiver and transmitter operation of a remote channel. This mode requires the remote channel receiver to be enabled. MULTIDROP MODE Users can program the channel to operate in a wake-up mode for Multidrop applications. This mode is selected by setting bits three and four in mode register one (MR1). In this mode of operation, a master station channel, connected to several slave stations (a maximum of 256 unique slave stations), transmits an address character followed by a block of data characters targeted for one or more of the slave stations. In this mode, the channel receivers within the slave stations are disabled, but they continuously monitor the data stream sent out from the master station. When the slave stations channel receivers detect any address character in the data stream, each receiver notifies its respective CPU by setting receiver ready (RXRDY) and generating an interrupt, if programmed to do so. Each slave station CPU then compares the received address to its station address and enables its receiver if it wants to receive the subsequent data from the master station. COUNTER/TIMER The 16-bit counter/timer (C/T) can operate in a counter mode or a timer mode. In either mode, users can program the C/T input (clock source) to come from several sources and program the C/T output to appear on output port pin OP3. The value (pre-load value) stored in the concatenation of the C/T upper register (CTUR) and the C/T lower register (CTLR) can be from 0x0001 through 0xFFFF and can be changed at any time. In counter mode, the CPU can start and stop the C/T. This mode allows the C/T to function as a system stopwatch, a real-time single interrupt generator, or a device watchdog. In timer mode, the C/T runs continuously; the CPU cannot start or stop it. Instead, the CPU only resets the C/T interrupt. This mode allows the C/T to be used as a programmable clock source for channels A and B, or periodic interrupt generator. At power-up and after reset, the C/T operates in timer mode. Slave stations that are not addressed continue monitoring the data stream for the next address character. An address character flags the end of one block of data and the start of another. After receiving a block of data, the slave stations CPU may disable the channel receiver and re-initiate the process. A transmitted character from the master station consists of a start bit, the programmed number of data bits, an address/data (A/ D) bit flag, and the programmed number of stop bits. The address/data bit identifies to the slave stations channel whether the character should be interpreted as an Rev. 1.10 13 XR88C92/192 XR88C92/192 COUNTER MODE In counter mode, the C/T counts down from the pre-load value using the programmed counter clock source. The counter clock source can be the channel A transmitter clock, the channel B transmitter clock, the external clock on the XTAL1 pin divided by sixteen, or an external clock on the input port pin IP2. The CPU can start and stop the counter, and can read the count value (CUR:CLR) if the counter is stopped. When a read at the start counter command address is performed, the counter is initialized to the pre-load value and begins a countdown sequence. When the counter counts from 0x0001 to 0x0000 (terminal count), the C/T-ready bit in the interrupt status register (ISR Bit-3) is set. 3 Users can program the counter to generate an interrupt request for this condition on the -INT output or output pin OP3. After 0x0000 the counter counts to 0xFFFF, and continues counting down from there. If the CPU changes the pre-load value, the counter will not recognize the new value until it receives the next start counter command (and is reinitialized). When a read at the stop counter command address is performed, the counter stops the countdown sequence and clears ISR Bit-3. The count value should only be read while the counter is stopped because only one of the count registers (either CUR or CLR) can be read at a time. If the counter is running, a decrement of CLR that requires a borrow from the CUR could take place between the two reads. down sequence. After reaching terminal count a second time, the timer sets the C/T-ready bit in the interrupt status register (ISR Bit-3), inverts its output, is re-initialized again, and begins a new countdown sequence. Users can program the timer to generate an interrupt request for this condition (every second countdown cycle) on the -INT output. If the CPU changes the pre-load value, the timer will not recognize the new value until either (a) it reaches the next terminal count and is reinitialized automatically, or (b) it is forced to re-initialize by a start command. When a read at the stop counter command address is performed, the timer clears ISR Bit-3 but does not stop. Because in timer mode the C/T runs continuously, it should be completely configured (preload value loaded and start counter command issued) before programming the timer output to appear on OP3. Use caution if the contents of a register are changed during receiver/ transmitter operation as certain changes can produce undesired results. For example, changing the number of bits per character while the transmitter is active can transmit an incorrect character. The contents of the clock-select register (CSR) and ACR Bit-7 should only be changed after the receiver(s) and transmitter(s) have been issued software RX and TX reset commands. Most bits of the mode registers should not be changed during receiver/transmitter operation, except that in Multidrop parity mode, the address/data parity type bit can be changed at any time. 44 Similarly, certain changes to the auxiliary control register (ACR Bits 4-6) should only be made while the counter/timer (C/T) is not used. Channel A mode registers MR1A and MR2A are accessed via an auxiliary pointer. The pointer is set to mode register one (MR1A) by RESET or by issuing a "reset pointer" command via the channel A command register. Any read or write of the mode register switches the pointer to mode register two (MR2A). All subsequent accesses will address MR2A unless the pointer is reset to MR1A as described above. The channel B mode registers MR1B and MR2B are accessed by an identical pointer independent of the channel A pointer. Mode, command, clock-select, and status registers are duplicated for each channel to allow independent operation and control (except that both channels are restricted to baud rates that are in the same set). TIMER MODE In timer mode, the C/T generates a square-wave output derived from the programmed timer input (clock source). The timer clock source can be the external clock on the XTAL1 input pin divided by one or sixteen, or it can be an external input on input port pin IP2 divided by one or sixteen. The square wave generated by the timer has a period of 2X (pre-load value) X (period of clock source), it is available as a clock source for both communications channels and can be programmed to appear on output pin OP3. The timer runs continuously, the CPU cannot stop it. Because the timer cannot be stopped, the count value (CUR:CLR) should not be read. When a read at the start counter command address is performed, the timer terminates the current countdown sequence, sets its output to 1 (appears un-inverted at OP3), is initialized to the pre-load value, and begins a new countdown sequence. When the counter counts from 0x0001 (terminal count), it inverts its output, is reinitialized to the pre-load value and repeats the count- Rev. 1.10 14 XR88C92/192 XR88C92/192 PROGRAMMING AND REGISTER DESCRIPTIONS A3 A2 A1 A0 0 0 0 0 0 0 0 0 1 1 1 1 1 1 1 1 0 0 0 0 1 1 1 1 0 0 0 0 1 1 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 0 1 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 0 1 READ WRITE Mode Register A (MR1A, MR2A) Status Register A (SRA) Reserved Receiver Buffer A (RBA) Input Port Change Register (IPCR) Interrupt Status Register (ISR) Counter/Timer MSB (CUR) Counter/Timer LSB(CLR) Mode Register B (MR1B, MR2B) Status Register B (SRB) Reserved Receiver Buffer B (RBB) Interrupt-Vector Register (IVR) Input Port (IP) Output Port Start-Counter Command Stop-Counter Command Mode Register A (MR1A, MR2A) Clock-Select Register A (CSRA) Command Register A (CRA) Transmitter Buffer A (TBA) Auxiliary Control Register (ACR) Interrupt Mask Register (IMR) Counter/ Timer Upper Register (CTUR) Counter/ Timer Lower Register (CTLR) Mode Register B (MR1B, MR2B) Clock-Select Register B (CSRB) Command Register B (CRB) Transmitter Buffer B (TBB) Interrupt-Vector Register (IVR) Configuration Register (OPCR) Output Port Register (OPR) Bit Reset Command Rev. 1.10 15 XR88C92/192 XR88C92/192 A3 A2 A1 A0 Register [Default] BIT-7 BIT-6 BIT-5 BIT-4 BIT-3 BIT-2 BIT-1 BIT-0 0 1 0 0 0 0 0 0 MRA0 [00] MRB0[00] Watch dog timer RX trigger level TX trigger level TX trigger level Not used Baud rate ext. 2 Not used Baud rate ext. 1 0 1 0 0 0 0 0 0 MRA1[00] MRB1[00] RX RTS control RX INT. type Error mode Parity mode Parity mode Parity type Word length Word length 0 1 0 0 0 0 0 0 MRA2[00] MRB2[00] Channel mode select Channel mode select TX RTS control TX CTS control Stop bit length Stop bit length Stop bit length Stop bit length 0 1 0 0 0 0 1 1 CSRA[00] CSRB[00] RX clock RX clock RX clock RX clock TX clock TX clock TX clock TX clock 0 1 0 0 0 0 1 1 SRA[00] SRB[00] Received break Framing error Parity error Overrun error Tx empty Tx ready Rx FIFO full Rx ready 0 1 0 0 1 0 0 0 CRA[00] CRB[00] Misc. command Misc. command Misc. command Misc. command TX disable TX enable RX disable RX enable 0 1 0 0 1 1 1 1 RHRA[XX] RHRB[XX] Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 0 1 0 0 1 1 1 1 THRA[XX] THRB[XX] Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 0 1 0 0 ACR[00] Baud rate set select C/T mode C/T mode C/T mode Delta IP3 int. Delta IP2 int. Delta IP1 int. Delta IP0 int. 0 1 0 0 IPCR[00] Delta IP3 Delta IP2 Delta IP1 Delta IP0 IP3 input IP2 input IP1 input IP0 input 0 1 0 1 ISR[00] Input port change Delta break B RxB ready/ FIFO full TxB ready C/T ready Delta break A RxA ready/ FIFO full TxA ready 0 1 0 1 IMR[00] Input port change Delta break B RxB ready/ FIFO full TxB ready C/T ready Delta break A RxA ready/ FIFO full TxA ready 0 1 1 0 CTU[00] Bit-15 Bit-14 Bit-13 Bit-12 Bit-11 Bit-10 Bit-9 Bit-8 0 1 1 1 CTL[00] Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 1 1 0 1 IPR[XX] Not Used IP6 IP5 IP4 IP3 IP2 IP1 IP0 1 1 0 1 OPCR[00] OP7 OP6 OP5 OP4 OP3 OP3 OP2 OP2 1 1 1 0 STCC[XX] X X X X X X X X 1 1 1 0 SOPB[00] Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 1 1 1 1 SPCC[XX] X X X X X X X X 1 1 1 1 ROPB Bit-7 Bit-6 Bit-5 Bit-4 Bit-3 Bit-2 Bit-1 Bit-0 Rev. 1.10 16 XR88C92/192 XR88C92/192 MR0 A/B Mode register 0. This register is accessed only when command is applied via CR A/B register. After reading or writing to MR0 A/B register, the pointer will point to MR1 A/B register. Bit-6 1 1 0 1 0 1 1 byte in FIFO 6 bytes in FIFO 12 bytes in FIFO 16 bytes in FIFO MR1 A/B Mode register 1. MR1 A/B are accessed after reset or by command applied via CR A/B register. After reading or writing to MR1 A/B register, the pointer will point to MR2 A/B register. MR0 A/B Bit-3. Special function. 0 = Normal 1 = Factory test mode. MR1 A/B Bits 1-0. Character Length 00=5 01=6 10=7 11=8 MR0 A/B Bits 5-4 Transmit trigger levels. MR0 Bit-4 0 1 0 1 XR88C192 XR88C192 MR0 A/B Bit-7. Receive time-out (watch dog timer). 0 = Disabled 1 = Enabled MR0 A/B Bit-2. Extended baud rate table selection. 0 = Normal baud rate tables 1 = Extend baud rate tables (2) MR0 Bit-5 0 0 1 1 MR1 Bit-6 0 0 1 1 MR0 A/B Bit-1. Special function. 0 = Normal 1 = Factory test mode. MR0 Bit-4 0 1 0 1 XR88C92 XR88C92 6 bytes in FIFO 8 bytes in FIFO MR0 Bit-6 MR0 A/B Bit-0. Extended baud rate table selection. 0 = Normal baud rate tables 1 = Extend baud rate tables (1) MR0 Bit-5 0 0 1 1 Bit-6 0 1 MR1 A/B Bit-2. Parity Type 0 = Even Parity 1 = Odd Parity XR88C92 XR88C92 8 FIFO locations empty 4 FIFO locations empty 6 FIFO locations empty 1 FIFO location empty MR1 A/B Bit 4-3. Parity mode 00 = With parity 01 = Force parity 10 = No parity 11 = Multidrop mode XR88C192 XR88C192 16 FIFO locations empty 6 FIFO locations empty 12 FIFO locations empty 1 FIFO location empty MR1 A/B Bit-5. Data error mode 0 = Single Character mode 1 = Block (FIFO) mode MR0 A/B Bit-6. Receive trigger levels. This bit is associated with MR1 Bit-6. MR0 MR1 Bit-6 Bit-6 XR88C92 XR88C92 0 0 1 byte in FIFO 0 1 3 bytes in FIFO MR1 A/B Bit-6. Receive Interrupt mode select. 0 = Single character mode (RxRdy) Rev. 1.10 17 XR88C92/192 XR88C92/192 1 = FIFO Full mode (FFULL) register. MR1 A/B Bit-7. Receive RTS flow control. 0 = Normal. No RTS control function. 1 = Auto RTS control function CSR A/B Bits 3-0. Transmit clock select (see baud rate table). CSR A/B Bits 7-4. Receive clock select (see baud rate table). MR2 A/B Mode register 2. This register is accessed when any read or write operation to MR1 A/B register is performed. Access to MR2 A/B do not change the pointer. MISCELLANEOUS COMMAND REGISTER CR A/B CR A/B register is used to supply commands to A/B channels. Multiple commands can be specified in a single write to CR A/B as long as commands are nonconflicting. MR2 A/B Bits 3-0. Stop bit length 0000 = 0.563 0001 = 0.625 0010 = 0.688 0011 = 0.750 0100 = 0.813 0101 = 0.875 0110 = 0.938 0111 = 1.000 1000 = 1.563 1001 = 1.625 1010 = 1.688 1011 = 1.750 1100 = 1.813 1101 = 1.875 1110 = 1.938 1111 = 2.000 CR A/B Bits 1-0. Receiver Commands 0 0 = No Action, Stays in Present Mode 0 1 = Receiver Enabled 1 0 = Receiver Disabled 1 1 = Don't Use CR A/B Bits 3-2. Transmitter Commands 0 0 = No Action, Stays in Present Mode 0 1 = Transmitter Enabled 1 0 = Transmitter Disabled 1 1 = Don't Use CR A/B Bits 7-4. Miscellaneous Commands. 0 0 0 0 = No Command. 0 0 0 1 = Reset MR Pointer to MR1. 0 0 1 0 = Reset Receiver. Receiver is disabled and FIFO is flushed. 0 0 1 1 = Reset Transmitter. Transmitter is disabled and FIFO is flushed. 0 1 0 0 = Reset Error Status. Clears channel A/B, break, parity, and over-run error bits in the status register. 0 1 0 1 = Reset Channels Break-Change Interrupt. Clears channel A/B break detect change bit in the interrupt status register (ISR Bit-2). 0 1 1 0 = Start Break. Forces the transmitter output to go low and stay low. If transmitter is empty the start of the break condition will be delayed up to two bit times. If transmitter is active, the break begins when transmission of the character is completed. All contents of the FIFO has to be transmitted before break MR2 A/B Bit-4. Auto CTS Flow control 0 = Normal. No CTS control function 1 = Auto CTS control function. MR2 A/B Bit-5. Transmit RTS control. 0 = Normal. No control function 1 = Transmit RTS function enable. MR2 A/B Bit 7-6. Channel Mode. 0 0 = Normal 0 1 = Automatic Echo 1 0 = Local Loopback 1 1 = Remote Loopback CLOCK SELECT REGISTER-CSR A/B Transmit / Receive baud rates can be selected via this Rev. 1.10 18 XR88C92/192 XR88C92/192 Baud Rate Table (based on a 3.6864MHz clock) MR0 Bits 2,0=0 MR0 Bit-0=1 (extended 1) MR0 Bit-2=1 (extended 2) CSR A/B 1000= 1001= 1 01 0 = 1011= 1100= SET-2 ACR Bit-7=1 SET-1 ACR Bit-7=0 SET-2 ACR Bit-7=1 SET-1 ACR Bit-7=0 SET-2 ACR Bit-7=1 0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 1110 1111 0111= SET-1 ACR Bit-7=0 50 110 134.5 200 300 600 1200 1050 2400 4800 7200 9600 38.4k Timer IP4-16X IP4-16X IP4-1X 75 110 134.5 150 300 600 1200 2000 2400 4800 1800 9600 19.2k Timer IP4-16X IP4-16X IP4-1X 300 110 134.5 1200 1800 3600 7200 1050 14.4k 28.8k 7200 57.6k 230.4k Timer IP4-16X IP4-16X IP4-1X 450 110 134.5 900 1800 3600 7200 2000 14.4k 28.8k 1800 57.6k 115.2k Timer IP4-16X IP4-16X IP4-1X 4800 880 1076 19.2k 28.8k 57.6k 115.2k 1050 57.6k 4800 57.6k 9600 38.4k Timer IP4-16X IP4-16X IP4-1X 7200 880 1076 14.4k 28.8k 57.6k 115.2k 2000 57.6k 4800 14.4k 9600 19.2k Timer IP4-16X IP4-16X IP4-1X command should be issued to force a reset of the ISR Bit-3. signal takes place. Transmitter must to be enabled for this command to be accepted. Stop Break. Transmit output will go high within two bit times. Set -RTS output to low. Reset -RTS output to high. Set Timeout Mode On. The receiver in this channel will restart the C/T as each receive character is transferred from the shift register to the receive FIFO. The C/T is placed in the counter mode, the START/STOP counter commands are disabled, the counter is stopped, and the Counter Ready Bit, ISR Bit3 is reset. (See also Watchdog timer description in the receiver section.) Set MR pointer to MR0. Disable Timeout Mode. This command returns control of the C/T to the regular Start/ Stop counter commands. It does not stop the counter or clear any pending interrupts. After disabling the timeout mode, a "Stop Counter" 1 1 0 1 = Not used. 1 1 1 0 = Power Down Mode On. In this mode, the DUART oscillator is stopped and all functions requiring this clock are suspended. The execution of commands other than disable power down mode (1111) requires a XTAL1. While in the power down mode, do not issue any commands to the CR A/B except the disable power down mode command. The contents of all registers will be saved while in this mode. It is recommended that the transmitter and receiver be disabled prior to placing the DUART into power down mode. This command is in CRA only. 1 1 1 1 = Disable Power Down Mode. This command restarts the oscillator. After invoking this Rev. 1.10 19 XR88C92/192 XR88C92/192 command, wait for the oscillator to start up before writing further commands to the CR A/ B. This command is in CRA only. For maximum power reduction input pins should be at GND or VCC. on receipt of a valid start bit when the FIFO is full and a character is already in the receive shift register waiting for an empty FIFO position. When this occurs, the character in the receive shift register (and its break detect, parity error, and framing error status, if any) is lost. A reset error status command clears this bit. STATUS REGISTER (SRA/SRB) SR A/B Bit-5. Parity Error. This bit becomes set when the "with parity" or "force parity" mode is programmed by mode register one and the corresponding character in the FIFO is received with incorrect parity. In the Multidrop mode, the parity error bit position stores the received address/data bit. This bit is valid only when the RxRDY bit is set (SR A/B Bit-0 = 1). SR A/B Bit-0. Receive Ready. This bit indicates that one or more character(s) has been received and is waiting in the FIFO for the CPU to read it. It is set when the first character is transferred from the receive shift register to the empty FIFO, and cleared when the CPU reads the receiver buffer, if there are no more characters in the FIFO after the read. SR A/B Bit-1. Receive FIFO Full. This bit is set when a character is transferred from the receive shift register to the receiver FIFO and the transfer fills the FIFO. All eight FIFO holding register positions are occupied. It is cleared when the CPU reads the receiver buffer, unless a fourth character is in the receive shift register waiting for an empty FIFO slot. SR A/B Bit-6. Framing Error. This bit (when set) indicates that a stop bit was not detected when the corresponding data character in the FIFO was received. The stop bit check is made in the middle of the first stop bit position. This bit is valid only when the RxRDY bit is set (SR A/B Bit-0 = 1). Framing error and break are exclusive. At least one data bit and/ or the parity bit must have been a "1" to signal a framing error. After a framing error, the receiver does not wait for the line to return to the marking state (high). If the line remains low for 1/2 a bit time after the stop bit sample (that is, the nominal end of the first stop bit), the receiver treats it as the beginning of a new start bit. SR A/B Bit-2. Transmit Ready. This bit (when set) indicates that the transmit holding register is empty and ready to be loaded with a character. Transmitter ready is set when the character is transferred to the transmit shift register. This bit is cleared when the CPU loads the transmit holding register, or when the transmitter is disabled. SR A/B Bit-3. Transmit Empty. This bit will be set when the channel A/B transmitter under-runs (empty). Both the transmit holding register and the transmit shift register are empty. It is set after transmission of the last stop bit of a character if no character is in the transmit holding register awaiting transmission. It is cleared when the CPU loads the transmit holding register or when the transmitter is disabled. SR A/B Bit-7. Received Break. This bit indicates an all-zero character of the programmed length has been received without a stop bit. This bit is valid only when the RxRDY bit is set (SR A/ B Bit-0 = 1). Only a single FIFO position is occupied when a break is received; additional entries to the FIFO are inhibited until the channel A/B receiver serial data input line returns to the marking state. The break-detect circuitry can detect a break that starts in the middle of a received character however, the break condition must persist completely through the end of the current character and the next character time to be recognized. SR A/B Bit-4. Overrun Error. This bit (when set) indicates one or more characters in the received data stream have been lost. It becomes set OUTPUT PORT CONFIGURATION REGISTER (OPCR) This register selects following options for output ports.4Alternate functions of OP1 and OP0 are con- Rev. 1.10 20 XR88C92/192 XR88C92/192 trolled by the mode registers, not the OPCR. MR1A Bit7 and MR2A Bit-5 control OP0. MR1B Bit-7 and MR2B Bit-5 control OP1. AUXILIARY CONTROL REGISTER (ACR) ACR Bits 3-0. This field selects which bits of the input port change register (IPCR) cause the input change bit in the interrupt status register (ISR Bit-7) to be set. 0 = Disabled 1 = Enabled OP2 output select Bit-1 Bit-0 0 0 Complement of OPR bit-2 0 1 TxAClk16-Transmit A 16X clock 1 0 TxAClk1-Transmit A 1X clock 1 1 RxAClk1- Receive A 1X clock ACR Bits 6-4. Counter/Timer Mode and Clock Source. Should only be altered while the C/T is not in use (stopped if in counter mode, output and/or interrupt masked if in timer mode). OP3 output select Bit-3 Bit-2 0 0 Complement of OPR bit-3 0 1 C/T Output 1 1 0 TxBClk1-Transmit B 1X clock 1 1 RxBClk1- Receive B 1X clock MODE Timer Timer Timer 111 OP5 output select (Bit 5) 0 = The complement of OPR bit-5 1 = -RxBRDY/-RxBFULL Counter Counter Counter Counter 100 101 110 OP4 output select (Bit 4) 0 = The complement of OPR bit-4 1 = -RxARDY/-RxAFULL SOURCE 000 001 010 011 If OP3 is to be used for the timer output, program the counter/timer for timer mode (ACR Bit-6 = 1), initialize the counter/timer pre-load registers (CTUR and CTLR), and the "start counter" command before setting OPCR Bits 3-2 = 01. CLOCK Timer External (IP2) TXAClk1-Transmit A 1X clock TXBClk1-Transmit B 1X clock Crystal or External Clock (XTAL1/Clk) Divided by 16 External (IP2) External (IP2) Divided by 16 Crystal or External Clock (XTAL1/Clk) Crystal or External Clock (XTAL1/Clk) Divided by 16 ACR Bit-7 Baud rate table Select. Should only be changed after both channels have been reset and are disabled. OP6 output select (Bit 6) 0 = The complement of OPR bit-6 1 = -TxARDY 0 = Set 1 1 = Set 2 OP7 output select (Bit 7) 0 = The complement of OPR bit-7 1 = -TxBRDY INPUT PORT CHANGE REGISTER (IPCR) Output Port Register (OPR) All bits, unless programmed for alternate function, can be set high or low individually: 0 = Sets output port high 1 = Sets output port low For example, setting bit-4 to 1 will set OP4 low. IP Level Bits 3-0. 0 = Low 1 = High IP Delta Bits 7-4. 0 = No 1 = Yes Rev. 1.10 21 XR88C92/192 XR88C92/192 INTERRUPT STATUS REGISTER (ISR) This register provides the status of all potential interrupt sources. The contents of this register are logically "AND"-ed with the contents of the interrupt mask register, and the results are "NOR"-ed to produce the -INT output. All active interrupt sources are visible by reading the ISR, regardless of the contents of the interrupt mask register. Reading the ISR has no effect on any interrupt source. Each active interrupt source must be cleared in a source-specific fashion to clear the ISR. All interrupt sources are cleared when the XR88C92/192 XR88C92/192 is reset. 4 ISR Bit-0. Transmit ready A. This bit is the channel A equivalent of ISR Bit-4. issues a channel B reset break change interrupt command. ISR Bit-7. Input port change status. This bit is a "1" when a change of state has occurred at the IP0, IP1, IP2, or IP3 inputs and that event has been enabled to cause an interrupt by the programming of ACR Bits 3-0. This bit is cleared when the CPU reads the input port change register. INTERRUPT MASK REGISTER (IMR) This register selects which bits in the interrupt status register can cause an interrupt output. If a bit in the interrupt status register is a "1" and the corresponding bit in this register is also a "1", the -INT output will be asserted. If the corresponding bit in this register is a zero, the state of the bit in the interrupt status register has no effect on the -INT output. Note that the interrupt mask register does not mask the programmable interrupt outputs OP7 through OP3 or the value read from the interrupt status register. ISR Bit-1. Receive ready A or FIFO full. The function of this bit is programmed by MR1A Bit-6. If programmed as receiver ready, it is a copy of the SRA Bit-0. If programmed as FIFO full, it is a copy of the SRA Bit-1. ISR Bit-2. Channel A change in break. This bit (when set) indicates that the channel A receiver has detected the beginning or the end of a break condition. It is reset when the CPU issues a channel A reset break change interrupt command. IMR Bit-0. 0 = Normal, no interrupt. 1 = Enable channel A transmit ready interrupt. IMR Bit-1. 0 = Normal, no interrupt. 1 = Enable channel A receive ready or FIFO full interrupt. RxRDY or FIFO-full is selected via MR1A Bit6. ISR Bit-3. Counter/Timer ready. In counter mode, this bit is set when the counter reaches terminal count. In timer mode, this bit is set each time the timer output switches from low to high. IMR Bit-2. 0 = Normal, no interrupt. 1 = Enable channel A received break signal interrupt. ISR Bit-4. Transmit ready B. This bit is a duplicate of the channel B status register transmitter ready bit. IMR Bit-3. 0 = Normal, no interrupt. 1 = Enable Timer/Counter interrupt. ISR Bit-5. Receive ready B or FIFO full. The function of this bit is programmed by MR1B Bit-6. If programmed as receiver ready, it is a copy of the SRB Bit-0. If programmed as FIFO full, it is a copy of the SRB Bit-1. IMR Bit-4. 0 = Normal, no interrupt. 1 = Enable channel B transmit ready interrupt. IMR Bit-5. 0 = Normal, no interrupt. 1 = Enable channel B receive ready or FIFO full interrupt. RxRDY or FIFO-full is selected via MR1B Bit6. ISR Bit-6. Channel B change in break. This bit (when set) indicates that the channel B receiver has detected the beginning or the end of a break condition. It is reset when the CPU Rev. 1.10 22 XR88C92/192 XR88C92/192 IMR Bit-6. 0 = Normal, no interrupt. 1 = Enable channel B received break signal interrupt. SOPR Bit 0-7. 0 = No change. 1 = Reset output port to high. IMR Bit-7. 0 = Normal, no interrupt. 1 = Enable input port state change interrupt. INPUT PORT REGISTER State of the input ports (IP0-IP6) can be read via this register. IPR Bit 0-6. 0 = Inputs are in low state. 1 = Inputs are in high state. IPR Bit-7. Not used and set to "0". COUNTER REGISTER (CUR and CLR) The count upper register (CUR) and count lower register (CLR) hold the most-significant byte and the leastsignificant byte, respectively, of the current counter value. These registers should only be read when the C/ T is in counter mode and the counter is stopped. START COUNTER / TIMER REGISTER Reading from this register will start Timer counter function. Returned data values should be ignored. STOP COUNTER TIMER REGISTER Reading from this register will issue a stop command to Timer counter function. Returned data values should be ignored. SET OUTPUT PORT REGISTER Output ports (OP0-OP7) can be set to low by writing a "1" to each individual bits. Outputs will change state only when OPCR register bits are assigned to general purpose output pins. When output is set to low, it can not change state to high unless reset output port command is issued. SOPR Bit 0-7. 0 = No change. 1 = Set output port to low. RESET OUTPUT PORT BITS REGISTER Each output port bit can be changed to high state by writing a "1" to each individual bit. Rev. 1.10 23 XR88C92/192 XR88C92/192 AC ELECTRICAL CHARACTERISTICS TA=0° - 70°C (-40° - +85°C for Industrial grade packages), Vcc=3.3 - 5.0 V ± 10% unless otherwise specified. Symbol T1w,T2w T3w TAS TAH TRWS TRWH TDD TDS TDH TDF TAKL TAKH TAKT TCSL TCSH T9s T9h T10d T11d TR N Parameter Limits 3.3 Min Max Clock pulse duration Oscillator/Clock frequency Address Valid to -CS Low -CS High to Address Invalid R/-W Setup Time to -CS Low R/-W Hold Time from -CS High -CS Low to Data Valid (Read) Data Valid to -CS High (Write) -CS High to Data Invalid (Write) -CS High to Data Hi-Z (Read) -CS Low to -DACK Low -CS High to -DACK High -CS High to -DACK Hi-Z -CS Low Pulse Width -CS High Pulse Width Port input setup time Port input hold time Delay from R/-W to output Delay to reset interrupt from R/-W Reset pulse width Baud rate divisor 17 Limits 5.0 Min Max 17 8 0 0 0 0 0 0 0 0 51 20 1 32 10 1 30 70 45 70 100 100 0 0 20 42 27 43 70 70 0 0 110 100 2 1 Rev. 1.10 24 24 ns 216-1 110 100 2 1 216-1 Units ns MHz ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns ns clks clks Conditions XR88C92/192 XR88C92/192 ABSOLUTE MAXIMUM RATINGS Supply range Voltage at any pin Operating temperature Storage temperature Package dissipation 7 Volts GND - 0.3 V to VCC +0.3 V -40° C to +85° C -65° C to 150° C 500 mW DC ELECTRICAL CHARACTERISTICS TA=0° - 70°C (-40° - +85°C for Industrial grade packages), Vcc=3.3 - 5.0 V ± 10% unless otherwise specified. Symbol Parameter VILCK VIHCK VIL VIH VOL VOL VOH VOH IIL ICL ICC ISB ISB CP Clock input low level Clock input high level Input low level Input high level Output low level on all outputs Output low level on all outputs Output high level Output high level Input leakage Clock leakage Avg power supply current Avg stand by supply current (88C92 88C92) Avg stand by supply current (88C192 88C192) Input capacitance Limits 3.3 Min Max Limits 5.0 Min Max -0.3 2.4 -0.3 2.0 -0.5 3.0 -0.5 2.2 0.6 VCC 0.8 0.6 VCC 0.8 VCC 0.4 0.4 2.4 2.0 ±10 ±10 3 3 150 5 Rev. 1.10 25 ±10 ±10 6 5 120 5 Units V V V V V V V V mA mA mA mA mA pF Conditions IOL= 5 mA IOL= 4 mA IOH= -5 mA IOH= -1 mA XR88C92/192 XR88C92/192 T AS T AH A 4 -A 1 T RW S TR W H -IO R / -IO W T CSL -C S T CSH T DD D 7 -D 0 (R e a d ) T DF V alid D ata T DS D 7 -D 0 (W rite ) T DH V alid D ata R e a d /W rite C ycle Tim in g Figure 2: Bus Timing (Read/Write cycle) IP6-IP0 T9s T9h -IOR XR92-IP XR92-IP Figure 3: Input Port Timing -IOW T10d OP7-OP0 Old Data New Data XR92-OP XR92-OP Figure 4: Output Port Timing Rev. 1.10 26 XR88C92/192 XR88C92/192 RX D1 D2 D8 D9 D10 D11 D12 D13 D12, D13 Will be lost due to RX disable RX ENABLE -RxRDY -FFULL -RxRDY/ -FFULL -IOR Status Data (D1) D11 Will be lost due to overrun OVERRUN ERROR Status Data Status Data Status Data (D2) (D3) (D10) Reset by command -RTS XR92-RX XR92-RX Figure 5: Receive Timing TX D1 D2 D3 Break D4 D5 TX ENABLE -TxRDY -IOW -CTS -RTS XR692-TX XR692-TX Figure 6: Transmit Timing Rev. 1.10 27 XR88C92/192 XR88C92/192 -IOW -IOR T11d -INT T11d XR92-NT XR92-NT Figure 7: Interrupt Timing T1w T2w ExCLK XR92-CK XR92-CK T3w Figure 8: External clock Timing Rev. 1.10 28 XR88C92/192 XR88C92/192 40 LEAD PLASTIC DUAL-IN-LINE (600 MIL PDIP) Rev. 1.00 40 21 E1 1 20 E D A2 Seating Plane A A1 L C B B1 e MILLIMETERS INCHES SYMBOL MIN MAX MIN MAX A 0.16 0.25 4.06 6.35 A1 0.015 0.07 0.38 1.78 A2 0.125 0.195 3.18 4.95 B 0.014 0.024 0.36 0.56 B1 0.03 0.07 0.76 1.78 C 0.008 0.014 0.2 0.38 D 1.98 2.095 50.29 53.21 E 0.6 0.625 15.24 15.88 E1 0.485 0.58 12.32 14.73 e 0.100 BSC 2.54 BSC eA 0.600 BSC 15.24 BSC eB 0.6 0.7 15.24 17.78 L 0.115 0.2 2.92 5.08 a 0° 15° 0° 15° Note: The control dimension is the inch column Rev. 1.10 29 eA eB XR88C92/192 XR88C92/192 44 LEAD PLASTIC LEADED CHIP CARRIER (PLCC) Rev. 1.00 C D Seating Plane D1 2 1 45° x H2 45° x H1 A2 44 B1 D D1 B D3 e R D3 A1 A SYMBOL A A1 A2 B B1 C D D1 D2 D3 e H1 H2 R INCHES MIN MAX 0.165 0.18 0.09 0.12 0.02 -. 0.013 0.021 0.026 0.032 0.008 0.013 0.685 0.695 0.65 0.656 0.59 0.63 0.500 typ. 0.050 BSC 0.042 0.056 0.042 0.048 0.025 0.045 MILLIMETERS MIN MAX 4.19 4.57 2.29 3.05 0.51 -0.33 0.53 0.66 0.81 0.19 0.32 17.4 17.65 16.51 16.66 14.99 16 12.70 typ. 1.27 BSC 1.07 1.42 1.07 1.22 0.64 1.14 Note: The control dimension is the inch column Rev. 1.10 30 D2 XR88C92/192 XR88C92/192 44 LEAD THIN QUAD FLAT PACK (10 mm x 10 mm x 1.4 mm, TQFP) Rev. 1.00 D D1 33 23 34 22 D1 44 12 1 11 B A2 e C A Seating Plane A1 SYMBOL A A1 A2 B C D D1 e L a L INCHES MIN 0.055 0.002 0.053 0.012 0.004 0.465 0.39 0.0315 0.018 0° MAX 0.063 0.006 0.057 0.018 0.008 0.48 0.398 BSC 0.03 7° MILLIMETERS MIN MAX 1.4 1.6 0.05 0.15 1.35 1.45 0.3 0.45 0.09 0.2 11.8 12.2 9.9 10.1 0.80 BSC 0.45 0.75 0° 7° Note: The control dimension is the inch column Rev. 1.10 31 D XR88C92/192 XR88C92/192 NOTICE EXAR Corporation reserves the right to make changes to the products contained in this publication in order to improve design, performance or reliability. EXAR Corporation assumes no responsibility for the use of any circuits described herein, conveys no license under any patent or other right, and makes no representation that the circuits are free of patent infringement. Charts and schedules contained here in are only for illustration purposes and may vary depending upon a user's specific application. While the information in this publication has been carefully checked; no responsibility, however, is assumed for in accuracies. EXAR Corporation does not recommend the use of any of its products in life support applications where the failure or malfunction of the product can reasonably be expected to cause failure of the life support system or to significantly affect its safety or effectiveness. Products are not authorized for use in such applications unless EXAR Corporation receives, in writing, assurances to its satisfaction that: (a) the risk of injury or damage has been minimized; (b) the user assumes all such risks; (c) potential liability of EXAR Corporation is adequately protected under the circumstances. Copyright 2000 EXAR Corporation Datasheet May 2000 Reproduction, in part or whole, without the prior written consent of EXAR Corporation is prohibited. Rev. 1.10 32