VIPC616 VIPC618 A16/D16 C95158 P-1024/D1 EK-VIPC616 VIPC664-ET VIPC664-WL

VIPC616 Four Slot 6U VMEbus IndustryPack Carrier Application Information The VIPC616 VMEbus IndustryPack carrier is part of the

www.sbs.com VIPC616 VIPC616 Four Slot 6U VMEbus IndustryPack Carrier Application Information The VIPC616 VIPC616 VMEbus IndustryPack carrier is part of the IndustryPack family of modular I/O components. As a 6U carier board, the VIPC616 VIPC616 provides mechanical mounting and the electrical interface from the VME backplane to four single-wide IndustryPacks or up to two double-wide IndustryPacks. The carrier supports I/O, ID, memory, and interrupt functions. The popular VIPC616 VIPC616 is a basic version of the enhanced VIPC618 VIPC618. The VIPC618 VIPC618 uses shielded 50-pin subminiature D connectors as the front panel I/O interface for significant reduction of EMI emissions and include latches. The VIPC616 VIPC616 features right-angled ribbon cable connectors on its front panel. In addition to the front panel cabling, most of the I/O signals of the C and D IndustryPacks are also routed to the VMEbus P2 backplane connector. This permits more flexible cabling options in many chassis. IndustryPack I/O is mapped into the VMEbus A16/D16 A16/D16 space. Both user and supervisor accesses are supported, as are read-modify-write ("test and set") operations. The size of I/O and ID spaces on each IP is fixed by the IndustryPack Specification. Memory is mapped into either A24 or A32 space. The A32 selection supports the full 8 Mbytes of memory per IndustryPAck slot. Interrupts are fully supported with a simple but powerful architecture. Each of the four IPs is able to generate up to two interrupt requests. These eight request lines are paired with the seven available VMEbus interrupt request levels by a simple jumper block. Alternatively, a user provided PLD may be installed to perform arbitrarily complex interrupt mappings. Front panel IP access acknowledge (ACK) and power check LEDs are provided for visual verification. Two power check circuits detect blown fuses and line faults on any IP slot. The VIPC616 VIPC616 provides fuse protection, RF filtering and de-coupling capacitance on all IP power lines. Features · Four IndustryPacks slots on a 6U VME board · Supports I/O, ID, memory, and interrupt cycles · Front panel I/O through unshielded right-angle ribbon connectors · 64 lines of backpanel I/O via P2 · A24 and A32 memory maps available · Up to 8 Mbytes of memory per slot · Front panel activity LEDs for each IndustryPack slot · Front panel power monitor LEDs · Filtered and fused power rails · Custom IRQ mapping available via PLD programming · 100% software compatible with the VIPC618 VIPC618 Revision 4 C95158 C95158 November 19, 1999 1 Released Specifications Form Factor VME Conformance IndustryPack Specification Number of IndustryPack Slots I/O Space ID Space Memory Space Interrupts Front Panel I/O Access Back Panel I/O Access Indicators IndustryPack Site Features Dimensions Weight Power Requirements Fuses Environmental Revision 4 C95158 C95158 November 19, 1999 6U VME Conforms to IEEE P-1024/D1 P-1024/D1.2 ANSI/VITA-4 1995 Four Up to two double-wide IndustryPacks may be fitted A16 space, 128 bytes per IndustryPack slot A16 space, 128 bytes per IndustryPack slot A24 space: none or 128 Kbytes to 2 Mbytes per IndustryPack slot A32 space: 8 Mbytes per IndustryPack slot fixed IndustryPack interrupts mapped 1:1 to VME IRQ levels by shunt or PLD selections. One pair of 50-pin right-angled keyed, shrouded ribbon cable connectors with ejection hardware for each pair of IndustryPack slots. All 50 I/O pins from slot D and a configurable selection of 14 pins from slot C routed to VME bus P2 rows A and C. One green LED per slot to show accesses One green LED to show power to slots A and B One green LED to show power to slots C and D 8 MHz only. IO cycles, ID cycles, memory cycles, interrupt acknowledge cycles. 32-bit interface and IndustryPack DMA are not supported. 160 mm x 233.35 mm 0.34 kg (0.81 lb) +5 VDC, 610 mA typical +12 VDC, 0 mA typical -12 VDC, 0 mA typical Additional power is consumed by IndustryPack modules +5 VDC @ 3A one per IndustryPack slot +12 VDC @ 3A one total -12 VDC @ 3A one total Operating temperature: 0 to 70°C Humidity: 5 to 95% non-condensing Storage: 40 to +85°C 2 Released Order Information VIPC616 VIPC616 Four slot, 6U VME IndustryPack carrier with front panel ribbon I/O connectors EK-VIPC616 EK-VIPC616 Engineering Kit for VIPC616 VIPC616. Contains: Printed hardware user manual Bill of materials Circuit schematic Assembly diagram The standard VIPC616 VIPC616 has each IndustryPack interrupt line mapped to a single VMEbus interrupt level. Versions of the board with custom PLD programming may be ordered with custom interrupt mappings. Contact the factory for details. Associated Products VIPC618 VIPC618 Four slot, 6U VMEbus IndustryPack carrier with front panel sheilded high-density I/O connectors VIPC664-ET VIPC664-ET Four slot, 6U VMEbus IndustryPack carrier with rear-panel I/O VIPC664-WL VIPC664-WL Four slot, wedge-locked 6U VMEbus IndustryPack carrier with rear-panel I/O VIPC664-WL-CC VIPC664-WL-CC Four slot, wedge-locked, conduction-cooled 6U VMEbus IndustryPack carrier with rearpanel I/O VIPC860-FP VIPC860-FP 6U VME MPC860T MPC860T Single Board Computer with Four IndustryPack Sites Industrypack I/O is via the front panel VIPC860-BP VIPC860-BP 6U VME MPC860T MPC860T Single Board Computer with Four IndustryPack Sites Industrypack I/O is via the back panel C-IP50F-IP50F-3 C-IP50F-IP50F-3 Three foot, 50 conductor ribbon cable C-IP50F-IP50F-6 C-IP50F-IP50F-6 Six foot, 50 conductor ribbon cable IP-TERM Fifty screw terminal block with ribbon cable connector 181 Constitution Drive, Menlo Park, California 94025 (650) 327-1200 · sales@sbs-mio.com · www.sbs.com Revision 4 C95158 C95158 November 19, 1999 3 Released