EN55022 MIL-STD-810F MIL-HDBK-217F CH-8002

TSR-1 Series, 1 A Features Up to 96 % efficiency No heat-sink required Pin compatible with LMxx linear regulators

DC/DC Converters TSR-1 Series, 1 A Features Up to 96 % efficiency No heat-sink required Pin compatible with LMxx linear regulators SIP-package fits existing TO-220 footprint Built in filter capacitors Operation temp. range 40°C to +85°C Short circuit protection Wide input operating range Excellent line / load regulation Low standby current 3-year product warranty The new TSR-1 series step-down switching regulators are drop-in replacement for inefficient 78xx linear regulators. A high efficiency up to 96 % allows full load operation up to +60 °C ambient temperature without the need of any heat-sink or forced cooling. The TSR-1 switching regulators provide other significant features over linear regulators, i.e. better output accuracy (±2 %), lower standby current of 2 mA and no requirement of external capacitors. The high efficiency and low standby power consumption makes these regulators an ideal solution for many battery powered applications. Models Order code Input voltage range Output voltage Output current max. Efficiency typ. @ Vin min. @ Vin max. TSR 1-2412 4.6 36 VDC* 1.2 VDC 74 % 62 % TSR 1-2415 4.6 36 VDC* 1.5 VDC 78 % 65 % TSR 1-2418 4.6 36 VDC* 1.8 VDC 82 % 69 % TSR 1-2425 4.6 36 VDC* 2.5 VDC TSR 1-2433 4.75 36 VDC* 3.3 VDC TSR 1-2450 6.5 36 VDC* 5.0 VDC TSR 1-2465 9.0 36 VDC* 87 % 75 % 91 % 78 % 94 % 84 % 6.5 VDC 93 % 87 % 1.0 A TSR 1-2490 12 36 VDC* 9.0 VDC 95 % 90 % TSR 1-24120 15 36 VDC* 12 VDC 95 % 92 % TSR 1-24150 18 36 VDC* 15 VDC 96 % 94 % * For input voltage higher than 32 VDC an input capcitor 22 µF / 50 V is required. See application notes (page 3) http://www.tracopower.com Page 1 of 3 DC/DC Converters TSR-1 Series 1A Input Specifications Maximum input current (@ Vin min. and 1 A output current) 1 A No load input current 1 mA typ. Reflected ripple current 150 mA ee application notes (page 3) for to s meet EN55022 EN55022 class A Input filter internal capacitors Output Specifications Voltage set accuracy ±2 % (at full load) Regulation Input variation 0.2 % Load variation (10 100 %)1.2 & 1.5 VDC models: 0.6 % other models: 0.4 % Overshoot startup voltage 1.0 % max. Minimum load not required Ripple and noise (20 MHz Bandwidth) 1.2 6.5 VDC models: 50 mVpk-pk max. 9 15 VDC models: 75 mVpk-pk max. Temperature coefficient ±0.015 % / °C max. Dynamic load response 50% load change (upper half) 150 mV max. peak variation 250 µS max. response time Startup rise time 10 % to 90 % Vout 2 mS Short circuit protection continuous, automatic recovery Current limitation @ 2.5 A typ. Capacitive load 470 µF max. General Specifications Temperature ranges Operating 40°C to +85°C Storage 55°C to +125°C Derating 2.4 %/K above 60°C Thermal shock acc. MIL-STD-810F MIL-STD-810F Humidity (non condensing) 95 % rel H max. Reliability, calculated MTBF (MIL-HDBK-217F MIL-HDBK-217F, @ 25°C, ground benign) >5'350'000 h Isolation voltage none Isolation capacity Input/Output 40 pF typ. Isolation resistance Input/Output >1`000 Mohm Switching frequency 500 kHz typ. Safety standards UL 60950-1, EN 60950-1, IEC 60950-1 Physical Specifications Casing material non-conductive plastic Potting material epoxy (flammability to UL 94V-0 rated) Package weight 1.9 g (0.07 oz) Soldering profile max. 265°C / 10 sec. (wave soldering) All specifications valid at nominal input voltage, full load and +25°C after warm-up time unless otherwise stated. http://www.tracopower.com Page 2 of 3 DC/DC Converters TSR-1 Series 1A Applications notes For input voltage higher than 32 VDC (max. 36 VDC) +Vin Input C1 = 22 µF / 50 V +Vout TSR 1 C1 Load GND Input filter to meet EN 55022 class A L1 Input +Vin C1 +Vout TSR 1 C2 GND Load C1 = 4.7 µF / 50 V C2 = 4.7 µF / 50 V L1 = 8.2 µH / 1.5 A / 0.08 Ohm Outline Dimensions Pin-Out 0.5(0.02) +Vin 2 GND 3 7.6 (0.30) Bottom view 2.0 (0.08) 0.3 (0.01) 1 +Vout 3 4.1 2 3.3 2.542.54 10.2 (0.40) (0.16) 1 0.5 (0.02) 11.7 (0.46) Dimensions in [mm], () = Inch Pin pitch tolerances: ±0.25 (±0.01) Pin profile tolerance: ±0.1 (±0.004) Other tolerances: ±0.5 (±0.02) (0.13) (0.1) (0.1) Specifications can be changed any time without notice. Rev. 06/09 Jenatschstrasse 1 · CH-8002 CH-8002 Zurich · Switzerland Tel. +41 43 311 45 11 · Fax +41 43 311 45 45 · info@traco.ch · www.tracopower.com Page 3 of 3