TLK2521 18BIT SLLS574D RXD10 RXD11 RXD12 RXD13 TXD14 TXD15 TXD16 TXD17 RXD17 - Datasheet Archive

 

1.0 to 2.5 Gbps 18BIT SERDES SLLS574D - JULY 2003 - REVISED JULY 2007 Serializer/Deserializer D High-Performance 64-Pin HTQFP

 

TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 Serializer/Deserializer D High-Performance 64-Pin HTQFP Thermally D D D D D D D D D Applications On-chip PLL Provides Clock Synthesis From Low-Speed Reference Receiver Differential Input Thresholds 200 mV Min Rated for Industrial Temperature Range Power: 424 mW at 2.5 Gbps Ideal for High-Speed Backplane Interconnect and Point-to-Point Data Link Passive Receive Equalizer TXD2 TXD1 TXD0 GNDA DOUTTXP DOUTTXN GNDA VDDA PREEMPH VDDA DINRXP DINRXN GNDA RXD0 D Enhanced Package (PowerPAD) 2.5-V Power Supply for Low Power Operation Selectable Signal Preemphasis Serial Output Interfaces to Backplane, Copper Cables, or Optical Converters Lock Indication and Sync Mode for Fast Initialization D 18-Bit Parallel Busses for Flexible Interface 1 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 2 47 3 46 4 45 5 44 6 43 7 42 8 41 9 40 10 39 11 38 12 37 13 36 14 35 15 34 33 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 VDD RXD3 RXD4 RXD5 RXD6 GND RXD7 RX_CLK RXD8 RXD9 VDD RXD10 RXD10 RXD11 RXD11 RXD12 RXD12 RXD13 RXD13 GND TXD14 TXD14 GND TXD15 TXD15 TXD16 TXD16 LOOPEN TXD17 TXD17 V DD ENABLE SYNC LOCKB TESTEN GND RXD17 RXD17 RXD16 RXD16 RXD15 RXD15 RXD14 RXD14 VDD TXD3 TXD4 TXD5 GND TXD6 TXD7 GTX_CLK VDD TXD8 TXD9 TXD10 TXD10 GND TXD11 TXD11 TXD12 TXD12 TXD13 TXD13 RXD1 RXD2 D Hot Plug Protection D 1 to 2.5 Gigabits Per Second (Gbps) Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. PowerPAD is a trademark of Texas Instruments. Copyright 2003 - 2007, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 1 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 description The TLK2521 TLK2521 is a member of the WizardLink family of multi-gigabit transceivers, intended for use in high-speed bidirectional point-to-point data transmission systems. The TLK2521 TLK2521 supports an effective serial interface speed of 1 Gbps to 2.5 Gbps, providing up to 2.25 Gbps of data bandwidth. The primary application of the TLK2521 TLK2521 is to provide high-speed I/O data channels for point-to-point baseband data transmission over controlled impedance media of approximately 50 . The transmission media can be printed circuit board, copper cables, or fiber-optic cable. The maximum rate and distance of data transfer is dependent upon the attenuation characteristics of the media and the noise coupling to the environment. The TLK2521 TLK2521 can also be used to replace parallel data transmission architectures by providing a reduction in the number of traces, connector pins, and transmit/receive pins. Parallel data loaded into the transmitter is delivered to the receiver over a serial channel, which can be a coaxial copper cable, a controlled impedance backplane, or an optical link. The data is then reconstructed into its original parallel format. It offers significant power and cost savings over current solutions, as well as scalability for higher data rate in the future. The TLK2521 TLK2521 performs the data parallel-to-serial, serial-to-parallel conversion, and clock extraction functions for a physical layer interface device. The serial transceiver interface operates at a maximum speed of 2.5 Gbps. The transmitter latches 18-bit parallel data at a rate based on the supplied reference clock (GTX_CLK). The 18-bit parallel data is internally encoded into 20 bits by framing the 18-bit data with a start and a stop bit. The resulting 20-bit word is then transmitted differentially at 20 times the reference clock (GTX_CLK) rate. The receiver section performs the serial-to-parallel conversion on the input data synchronizing the resulting 20-bit wide parallel data to the extracted reference clock (RX_CLK). It then extracts the 18 bits of data from the 20-bit wide data resulting in 18 bits of parallel data at the receive data pins (RXD0-17 RXD0-17). This results in an effective data payload of 900 Mbps to 2.25 Gbps (18 bits data x GTX_CLK frequency). The TLK2521 TLK2521 is housed in a high performance, thermally enhanced, 64-pin HTQFP PowerPAD package. Use of the PowerPAD package does not require any special considerations except to note that the PowerPAD, which is an exposed die pad on the bottom of the device, is a metallic thermal and electrical conductor. It is strongly recommended that the TLK2521 TLK2521 PowerPAD be soldered to the grounded thermal land on the board, since the PowerPAD also constitutes a major electrical ground connection for the TLK2521 TLK2521. All ac performance specifications in this data sheet are measured with the PowerPAD soldered to the test board. The TLK2521 TLK2521 provides an internal loopback capability for self-test purposes. Serial data from the serializer is passed directly to the deserializer allowing the protocol device a functional self-check of the physical interface. The TLK2521 TLK2521 is designed to be hot plug capable. An on-chip power-on reset circuit holds the RX_CLK low and places the parallel side output signal pins, DOUTTXP and DOUTTXN, into a high-impedance state during power up. The TLK2521 TLK2521 uses a 2.5-V supply. The I/O section is 3-V compatible. The TLK2521 TLK2521 is characterized for operation from -40°C to 85°C. 2 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 functional block diagram TD(0-17) 18-Bit Register LOOPEN DOUTTXP 18 Start/Stop Encoder Parallel to Serial 20 DOUTTXN Bit Clock PREEMPH Multiplying Clock Synthesizer GTX_CLK TESTEN Controls: PLL,Bias,Rx, Tx ENABLE Bit Clock Interpolator and Clock Recovery MUX Recovered Clock LOCKB RD(0-17) 18-Bit Register RX_CLK 18 Start/Stop Decoder 20 Serial to Parallel MUX DINRXP DINRXN transmit interface The transmitter portion registers valid incoming 18-bit wide data (TXD[0:17]) on the rising edge of GTX_CLK. The data is then framed with a start and a stop bit, serialized and transmitted sequentially over the differential high-speed I/O channel. The clock multiplier multiplies the reference clock (GTX_CLK) by a factor of 10 times creating a bit clock. This internal bit clock is fed to the parallel-to-serial shift register, which transmits data on both the rising and falling edges of the bit clock providing a serial data rate that is 20 times the reference clock. Data is transmitted LSB (D0) first. transmit data bus The transmit bus interface accepts 18-bit wide single-ended TTL parallel data at the TXD[0:17] pins. Data is valid on the rising edge of GTX_CLK. The GTX_CLK is used as the word clock. The data and clock signals must be properly aligned as shown in Figure 1. Detailed timing information can be found in the TTL input electrical characteristics table. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 3 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 GTX_CLK TXDn tsu th Figure 1. Transmit Timing Waveform transmission latency The data transmission latency of the TLK2521 TLK2521 is defined as the delay from the initial 18-bit word load to the serial transmission of bit 0. The transmit latency is fixed once the link is established. However, due to silicon process variations and implementation variables such as supply voltage and temperature, the exact delay varies slightly. Figure 2 illustrates the timing relationship between the transmit data bus, GTX_CLK, and serial transmit pins. Detailed latency information can be found in the transmitter/receiver characteristics table. Transmitted 20-Bit Word DOUTTXP, DOUTTXN td(Tx latency) TXD(0-17) 16-Bit Word to Transmit GTX_CLK Figure 2. Transmitter Latency start/stop framing logic All true serial interfaces require a method of encoding to insure minimum transition density so that the receiving PLL has a minimal number of transitions in which to stay locked onto the data stream. The signal coding also provides a mechanism for the receiver to identify the byte boundary for correct deserialization. The TLK2521 TLK2521 wraps a start bit (1) and a stop bit (0) around the 18-bit data payload as shown in Figure 3. This is transparent to the user as the TLK2521 TLK2521 internally adds the framing bits to the data such that the user reads and writes actual 18-bit data. start/stop framing logic (continued) Stop Start Bit Bit TD0 TD1 . TD16 TD17 Stop Bit Start Bit Figure 3. Serial Output Data Stream with Start and Stop Bit 4 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 parallel-to-serial The parallel-to-serial shift register takes in the 20-bit wide data word multiplexed from the framing logic and converts it to a serial stream. The shift register is clocked on both the rising and falling edge of the internally generated bit clock, which is 10 times the GTX_CLK input frequency. The LSB (TD0) is transmitted first as shown in Figure 3. high-speed data output The high-speed data output driver consists of a PECL-compatible differential pair that can be optimized for a particular transmission line impedance and length. The line can be directly coupled or ac coupled. AC-coupling is only recommended if the parallel TX data stream is encoded to achieve a dc-balanced data stream. See Figure 11 and Figure 12 for termination details. No external pullup or pulldown resistors are required. The TLK2521 TLK2521 provides a selectable signal preemphasis option for driving lossy media. The first bit of a run length of same-value bits is driven to a larger output swing, which precompensates for signal inter-symbol interference (ISI) in lossy media such as copper cables or printed circuit board traces due to preemphasis. receive interface The receiver portion of the TLK2521 TLK2521 accepts 20-bit framed differential serial data. The interpolator and clock recovery circuit locks to the data stream and extracts the bit rate clock. This recovered clock is used to retime the input data stream. The serial data is then aligned to the 20-bit word boundary by finding the start/stop bits, and the 18-bit data is output on a 18-bit wide parallel bus synchronized to the extracted receive clock. receive data bus The receive bus interface drives 18-bit wide single-ended TTL parallel data at the RXD[0:17] pins. Data is valid on the rising edge of RX_CLK. The RX_CLK is used as the recovered word clock. The data and clock signals are aligned as shown in Figure 4. Detailed timing information can be found in the TTL output switching characteristics table. RX_CLK RXDn tsu th Figure 4. Receive Timing Waveform POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 5 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 data reception latency The serial-to-parallel data receive latency is the time from when the first bit arrives at the receiver until it is output in the aligned parallel word with RXD0 received as first bit. The receive latency is fixed once the link is established. However, due to silicon process variations and implementation variables such as supply voltage and temperature, the exact delay varies slightly. Figure 5 illustrates the timing relationship between the serial receive pins, the recovered word clock (RX_CLK), and the receive data bus. Detailed latency information can be found in the transmitter/receiver characteristics table. 20-Bit Encoded Word DINTXP, DINTXN R(latency) RXD(0-17) 18-Bit Decoded Word RX_CLK Figure 5. Receiver Latency serial-to-parallel Serial data is received on the DINRXP and DINRXN pins. The interpolator and clock recovery circuit locks to the data stream if the clock to be recovered is within ±100 PPM of the internally generated bit rate clock. The recovered clock is used to retime the input data stream. The serial data is then clocked into the serial-to-parallel shift registers. synchronization mode The deserializer PLL must synchronize to the serializer in order to receive valid data. Synchronization can be accomplished in one of two ways. rapid synchronization The serializer has the capability to send specific SYNC patterns consisting of nine ones and nine zeros, switching at the input clock rate. The transmission of SYNC patterns enables the deserializer to lock to the serializer signal within a deterministic time frame. The transmission of SYNC patterns is selected via the SYNC input on the serializer. Upon receiving a valid SYNC pulse (wider than 6 clock cycles), 1026 cycles of SYNC pattern are sent. When the deserializer detects edge transitions at the serial input, it attempts to lock to the embedded clock information. The deserializer LOCKB output remains inactive while its clock/data recovery (CDR) locks to the incoming data or SYNC patterns present on the serial input. When the deserializer locks to the serial data, the LOCKB output goes active. When LOCKB is active, the deserializer outputs represent incoming serial data. One approach is to tie the deserializer LOCKB output directly to the SYNC input of the transmitter. random lock synchronization The deserializer can attain lock to a data stream without requiring the serializer to send special SYNC patterns. This allows the TLK2521 TLK2521 to operate in open-loop applications. Equally important is the deserializer's ability to support hot insertion into a running backplane. In the open-loop or hot-insertion case, it is assumed the data stream is essentially random. Therefore, because lock time varies due to data stream characteristics, the exact lock time cannot be predicted. The primary constraint on the random lock time is the initial phase relation between the incoming data and the GTX_CLK when the deserializer powers up. 6 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 random lock synchronization (continued) The data contained in the data stream can also affect lock time. If a specific pattern is repetitive, the deserializer could enter false lock-falsely recognizing the data pattern as the start/stop bits. This is referred to as repetitive multitransition (RMT). This occurs when more than one low-high transition takes place per clock cycle over multiple clock cycles. In the worst case, the deserializer could become locked to the data pattern rather than the clock. Circuitry within the deserializer can detect that the possibility of false lock exists. Upon detection, the circuitry prevents the LOCKB from becoming active until the potential false-lock pattern changes. Notice that the RMT pattern only affects the deserializer lock time, and once the deserializer is in lock, the RMT pattern does not affect the deserializer state as long as the same data boundary happens each cycle. The deserializer does not go into lock until it finds a unique data boundary that consists of four consecutive start/stop bits at the same position. The deserializer stays in lock until it cannot detect the same data boundary (start/stop bits) for four consecutive cycles. Then the deserializer goes out of lock and hunts for the new data boundary (start/stop bits). In the event of loss of synchronization, the LOCKB pin output goes inactive and the outputs (including RX_CLK) enter a high-impedance state. The user's system should monitor the LOCKB pin in order to detect a loss of synchronization. Upon detection of loss of lock, sending SYNC patterns for resynchronization is desirable if reestablishing lock within a specific time is critical. However, the deserializer can lock to random data as previously noted. LOCKB is held inactive for at least nine cycles after loss of lock is detected. power-down mode When the ENABLE pin is deasserted low, the TLK2521 TLK2521 goes into a power-down mode. In the power-down mode, the serial transmit pins (DOUTTXP, DOUTTXN) and the receive data bus pins (RXD[0:17]) go into a high-impedance state. reference clock input The reference clock (GTX_CLK) is an external input clock that synchronizes the transmitter interface. The reference clock is then multiplied in frequency 10 times to produce the internal serialization bit clock. The internal serialization bit clock is frequency locked to the reference clock and used to clock out the serial transmit data on both its rising and falling edge clock providing a serial data rate that is 20 times the reference clock. The receiver tracking logic uses clock phases from the internal PLL as it aligns the recovered clock phase with the incoming serial data stream; therefore, the input reference clock (GTX_CLK) is needed even if the transmit function of the TLK2521 TLK2521 is not being used. The receiver function has the ability to track an incoming serial data stream that is within ±200 ppm of the data rate that is set by GTX_CLK. This allows the use of clock sources with ±100 ppm frequency tolerance. operating frequency range The TLK2521 TLK2521 may operate at a serial data rate between 1 Gbit/s to 2.5 Gbit/s. GTX_CLK must be within ±100 PPM of the desired parallel data rate clock. testability The TLK2521 TLK2521 has a comprehensive suite of built-in self-tests. The loopback function provides for at-speed testing of the transmit/receive portions of the circuitry. The ENABLE pin allows for all circuitry to be disabled so that an IDDQ test can be performed. loop-back testing The transceiver can provide a self-test function by enabling (LOOPEN) the internal loop-back path. Enabling this pin causes serial transmitted data to be routed internally to the receiver. The parallel data output can be compared to the parallel input data for functional verification. (The external differential output is held in a high-impedance state during the loop-back testing.) POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 7 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 power-on reset Upon application of minimum valid power, the TLK2521 TLK2521 generates a power-on reset. During the power-on reset the RXD pins are tri-stated. RX_CLK is held low. The length of the power-on reset cycle is dependent upon the REFCLK frequency but is less than 1 ms in duration. Terminal Functions TERMINAL NAME NO. TYPE DESCRIPTION SIGNAL PIN DOUTTXP 60 DOUTTXN 59 DINRXP 54 DINRXN 53 GTX_CLK 8 TXD0 2 TXD4 3 TXD5 4 TXD6 Serial receive inputs. DINRXP and DINRXN together are the differential serial input interface from a copper or an optical I/F module. 64 TXD3 Input 63 TXD2 Serial transmit outputs. DOUTTXP and DOUTTXN are differential serial outputs that interface to copper or an optical I/F module. These terminals transmit NRZ data at a rate of 20 times the GTX_CLK value. DOUTTXP and DOUTTXN are put in a high-impedance state when LOOPEN is high and are active when LOOPEN is low. During power-on reset, these pins are high impedance. 62 TXD1 Output (High-Z power up) 6 TXD7 10 Reference clock. GTX_CLK is a continuous external input clock that synchronizes the transmitter interface TXD. The frequency range of GTX_CLK is 50 MHz to 125 MHz. The transmitter uses the rising edge of this clock to register the 18-bit input data (TXD) for serialization. 7 TXD8 Input TXD9 11 TXD1 16 TXD14 TXD14 17 TXD15 TXD15 19 TXD16 TXD16 20 TXD17 TXD17 22 RXD0 51 RXD1 50 RXD2 49 RXD3 47 RXD4 46 RXD5 45 RXD6 44 RXD7 42 RXD8 40 RXD9 39 RXD10 RXD10 37 RXD11 RXD11 36 RXD12 RXD12 35 RXD13 RXD13 Receive data bus. These outputs carry 18-bit parallel data output from the transceiver to the protocol device, synchronized to RX_CLK. The data is valid on the rising edge of RX_CLK as shown in Figure 10. These pins are 3-stated during power-on reset. These pins are also high impedance when enable=0. 15 TXD13 TXD13 Output (High-Z on power up) 14 TXD12 TXD12 Transmit data bus. These inputs carry the 18-bit parallel data output from a protocol device to the transceiver for encoding, serialization and transmission. This 18-bit parallel data is clocked into the transceiver on the rising edge of GTX_CLK as shown in Figure 9. 12 TXD11 TXD11 Input 34 8 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 TERMINAL NAME NO. TYPE DESCRIPTION RXD14 RXD14 32 RXD15 RXD15 31 RXD16 RXD16 30 RXD17 RXD17 29 RX_CLK 41 Output (low on power up) Recovered clock. Output clock that is synchronized to RXD. RX_CLK is the recovered serial data rate clock divided by 20. RX_CLK is held low during power-on reset. These pins are also high impedance when enable=0. SYNC 25 Input (w/pulldown) Fast synchronization. When asserted high, the transmitter substitute the 18-bit pattern 111111111000000000 ,so that when the start/stop bits are framed around the data the receiver can immediately detect the proper deserialization boundary. This is typically used during initialization of the serial link. PREEMPH 56 Input Preemphasis. When asserted, the serial transmit outputs have an extra output swing on the first bit of any run-length of same value bits than when deasserted. ENABLE 24 Input (w/pullup) Device enable. When this pin is held low, the device is placed in power down mode. When asserted high while the device is in power-down mode, the transceiver goes into power-on reset before beginning normal operation. LOOPEN 21 Input (w/pulldown) Loop enable. When LOOPEN is active high, the internal loop-back path is activated. The transmitted serial data is directly routed internally to the inputs of the receiver. This provides a self-test capability in conjunction with the protocol device. The DOUTTXP and DOUTTXN outputs are held in a high-impedance state during the loop-back test. LOOPEN is held low during standard operational state with external serial outputs and inputs active. LOCKB 26 Output Receiver lock. When asserted low, it indicates that the receiver has acquired bit synchronization on the data stream and has located the start/stop bits, so that the deserialized data presented on the parallel receive bus is properly received. These pins are also high impedance when enable=0. TESTEN 27 Input (w/pulldown) Test mode enable. This pin should be left unconnected or tied low. TEST PIN POWER PIN VDD 1, 9, 23, 38, 48 Supply Digital logic power. Provides power for all digital circuitry and digital I/O buffers. VDDA 55, 57 Supply Analog power. VDDA provides a supply reference for the high-speed analog circuits, receiver and transmitter. GNDA 52, 58, 61 Ground Analog ground. GNDA provides a ground reference for the high-speed analog circuits, RX and TX. GND 5, 13, 18, 28, 33, 43 Ground Digital logic ground. Provides a ground for the logic circuits and digital I/O buffers. GROUND PIN POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 9 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 absolute maximum ratings over operating free-air temperature (unless otherwise noted) Supply voltage, VDD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to 3 V Voltage range at TXD, ENABLE, GTX_CLK, LOOPEN, SYNC, PREEMPH . . . . . . . . . . . . . . . . . . . -0.3 V to 4 V Voltage range at any other terminal except above . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -0.3 V to VCC + 0.3 V Package power dissipation, PD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Storage temperature, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -65°C to 150°C Electrostatic discharge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . HBM:2 kV, CDM:1.5 kV Characterized free-air operating temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -40°C to 85°C Lead Temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTE 1: All voltage values, except differential I/O bus voltages, are with respect to network ground. DISSIPATION RATING TABLE TA 25°C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C POWER RATING PAP64 PAP64 PAP64 PAP64§ 3.22 W 32.15 mW/°C 1.77 W 0.94 W 9.46 mW/°C 0.52 W PAP64 PAP64¶ 0.68 W 6.78 mW/°C 0.37 W PACKAGE This is the inverse of the traditional junction-to-ambient thermal resistance (RJA) High K-board with solder § High K-board without solder ¶ Low K-board NOTE: For more information, see the TI application note PowerPAD Thermally Enhanced Package, TI (SLMA002 SLMA002). electrical characteristics over recommended operating conditions PARAMETER VDD TA TEST CONDITION MIN Operating free-air temperature TYP MAX 2.3 Supply voltage 2.5 2.7 V 85 °C -40 VDD = 2.5 V, Freq = 1 Gb/sec, PRBS pattern VDD = 2.5 V, Freq = 2.5 Gb/sec, PRBS pattern UNIT 71 ICC Supply current PD Power dissipation VDD = 2.5 V, Freq = 1 Gb/sec, PRBS pattern VDD = 2.5 V, Freq = 2.5 Gb/sec, PRBS pattern Shutdown current VDD = 2.75 V, Freq = 2.5 Gb/sec, worst case pattern ENABLE = 0, VDDA, VDD pins, VDD = max 130 PLL startup lock time VDD, VDDA = 2.3 V, EN to PLL acquire 0.1 mA 170 178 424 mW 730 Data acquisition time µA 0.4 1024 ms bits reference clock (GTX_CLK) timing requirements over recommended operating conditions (unless otherwise noted) PARAMETER R Frequency MIN TYP MAX UNIT Minimum data rate TEST CONDITIONS TYP-0.01% 50 TYP+0.01% MHz Maximum data rate TYP-0.01% 125 TYP+0.01% MHz 100 ppm Frequency tolerance Duty cycle Jitter# -100 40% Peak-to-peak POST OFFICE BOX 655303 60% 40 # See the Reference Lock Jitter Analysis For TLK2521 TLK2521 application note for more information. 10 50% · DALLAS, TEXAS 75265 ps TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 TTL input electrical characteristics over recommended operating conditions (unless otherwise noted) TTL Signals: TXD0 .TXD17 TXD17, GTX_CLK, LOOPEN, SYNC, PREEMPH PARAMETER TEST CONDITIONS MIN TYP MAX 2 UNIT VIH VIL High-level input voltage See Figure 6 Low-level input voltage See Figure 6 3.6 V 0.8 V IIH IIL High-level input current Low-level input current VDD = MAX, VIN = 2 V VDD = MAX, VIN = 0.4 V 40 µA CIN Input capacitance 0.8 V to 2 V tr tf GTX_CLK, TXD rise time 0.8 V to 2 V, C = 5 pF, See Figure 6 1 ns GTX_CLK, TXD fall time 2 V to 0.8 V, C = 5 pF, See Figure 6 1 ns tsu th TXD setup to GTX_CLK See Figure 6 1.5 ns TXD hold to GTX_CLK See Figure 6 0.4 ns µA -40 4 pF 2V RX_CLK 0.8 V 0V tr(slew) tf(slew) 2V RXD(0-17) 0.8 V 0V tr(slew) tsu tf(slew) th Figure 6. TTL Data Input Valid Levels for AC Measurements POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 11 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 TTL output switching characteristics over recommended operating conditions (unless otherwise noted) PARAMETER TEST CONDITIONS MIN TYP 2.1 2.3 GND 0.25 MAX UNIT VOH VOL High-level output voltage Low-level output voltage IOH= -1 mA, VDD = MIN IOL= 1 mA, VDD = MIN tr(slew) tf(slew) Magnitude of RX_CLK, RXD slew rate (rising) 0.8 V to 2 V, C = 5 pF, See Figure 10 0.5 V/ns Magnitude of RX_CLK, RXD slew rate (falling) 0.8 V to 2 V, C = 5 pF, See Figure 10 0.5 V/ns tsu th V 0.5 V 50% voltage swing, GTX_CLK = 50 MHz, See Figure 7 ns 3 ns 50% voltage swing, GTX_CLK = 50 MHz, See Figure 7 8 ns 50% voltage swing, GTX_CLK = 125 MHz, See Figure 7 RXD hold to RX_CLK 8 50% voltage swing, GTX_CLK = 125 MHz, See Figure 7 RXD setup to RX_CLK 3 ns 2V RX_CLK 0.8 V 0V tr(slew) tf(slew) 2V RXD(0-17) 0.8 V 0V tr(slew) tsu tf(slew) th Figure 7. TTL Data Output Valid Levels for AC Measurements 12 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 transmitter/receiver characteristics PARAMETER TEST CONDITION MIN TYP MAX UNIT VOD(p) = |VTXP-VTXN|, Preemphasis VOD, direct DC coupled. Preemphasis = high, See Figure 8 675 900 1280 VOD(p) DC coupled. Preemphasis = low, See Figure 8 600 800 1210 Differential, peak to peak output voltage with preemphasis DC coupled. Preemphasis = high, See Figure 8 1350 1800 2560 VOD(pp-p) DC coupled. Preemphasis = low, See Figure 8 1200 1600 2420 VOD(d) VD(d) = |VTXP-VTXN|, De-emphasis VOD, direct DC coupled. See Figure 8 500 750 1100 mV VOD(pp-d) Differential, peak to peak output voltage with deemphasis DC coupled. See Figure 8 1000 1500 2200 mV V(cmt) Transmit termination voltage range, (VTXP + VTXN)/2 1000 1250 1400 mV VID Receiver input voltage differential VID= |RXP ­ RXN| 200 Vcmr Receiver common-mode voltage range, (VRXP + VRXN)/2 1000 VDD- 350 mV -10 10 µA 2 pF Iin Cin Receiver input leakage RL = 50 , CL = 5 pF, See Figure 12 Serial transmit data total jitter (peak-to-peak) Differential output jitter, random + deterministic, 223-1 PRBS pattern at 2.5 Gbps Receive jitter tolerance tt, tf Total input jitter, PRBS pattern, permitted eye closure at zero crossing 100 150 ps 0.15 UI 0.5 UI At 1 Gbps Rlatency RX latency 19 18 21 88 95 At 2.5 Gbps TX latency 16 At 2.5 Gbps At 1 Gbps Tlatency mV mV Receiver input capacitance Differential output signal rise, fall time (20% to 80%) mV 90 103 Bit times Bit times VOD(p) VOD(d) VOD(pp_d) VOD(pp_p) V(cmt) tf tr VOD(d) Bit Time Bit Time VOD(p) Figure 8. Differential and Common-Mode Output Voltage Definitions POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 13 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 80% 50% 20% DOUTXP tr tf 80% 50% 20% DOUTXN tf tr +V DOUTXP DOUTXN 80% 0V 20% -V tr tf Figure 9. Rise and Fall Time Definitions thermal characteristics PARAMETER RJA Junction-to-free-air thermal resistance RJC Junction-to-case thermal resistance RJA Junction-to-free-air thermal resistance RJC Junction-to-case thermal resistance RJA Junction-to-case thermal resistance 14 MIN TYP Board mounted, no air flow, high conductivity TI recommended test board with thermal land but no solder or grease thermal connection to thermal land MAX UNIT 21.47 42.2 Junction-to-free-air thermal resistance RJC TEST CONDITION Board mounted, no air flow, high conductivity TI recommended test board, chip soldered or greased to thermal land 0.38 0.38 75.83 Board mounted, no air flow, JEDEC test board POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 7.8 °C/W °C/W °C/W TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 Recommended use of 0.01-µF Capacitor per VDD terminal 0.01 µF 5 at 100 MHz RXD1 RXD2 RXD0 TXD0 TXD2 TXD1 0.01 µF 0.01 µF 0.01 µF 0.01 µF 3 TXD5 4 45 GND 5 44 RXD6 TXD6 6 43 GND TXD7 7 42 RXD7 GTX_CLK 8 41 RX_CLK VDD TXD8 9 40 RXD8 10 39 RXD9 TXD9 11 38 VDD TXD10 TXD10 12 37 RXD10 RXD10 GND 13 36 RXD11 RXD11 TXD11 TXD11 14 35 RXD12 RXD12 TXD12 TXD12 15 34 RXD13 RXD13 TXD13 TXD13 33 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 GND RXD14 RXD14 RXD15 RXD15 RXD16 RXD16 46 RXD17 RXD17 GND TESTEN SYNC LOCKB TXD17 TXD17 V DD ENABLE LOOPEN GND TXD15 TXD15 TXD16 TXD16 TXD14 TXD14 GNDA TXD4 VDD RXD3 RXD4 RXD5 DINRXP 47 DINRXN 2 DOUTTXP 64 63 62 61 60 59 58 57 56 55 54 53 52 51 50 49 48 DOUTTXN 1 GNDA VDD TXD3 GNDA V DDA PREEMPH V DDA VDD Figure 10. External Component Interconnection ORDERING INFORMATION Orderable TLK2521 TLK2521 POST OFFICE BOX 655303 TLK2521IPAP TLK2521IPAP · DALLAS, TEXAS 75265 15 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 TXP RXP VDD ZO ZO 5 k ZO 7.5 k ZO TXN Transmitter + _ GND RXN Media Receiver Figure 11. High-Speed I/O Directly Coupled Mode TXP RXP VDD ZO ZO 5 k ZO 7.5 k ZO TXN Transmitter + _ GND RXN Media Receiver Figure 12. High-Speed I/O AC-Coupled Mode AC-coupling is only recommended if the parallel TX data stream is encoded to achieve a dc-balanced data stream. Otherwise, the ac-caps can induce common-mode voltage drift due to the dc-unbalanced data stream. designing with PowerPAD The TLK2521 TLK2521 is housed in a high-performance, thermally enhanced, 64-pin HTQFP (PAP64 PAP64) PowerPAD package. Use of the PowerPAD package does not require any special considerations except to note that the PowerPAD, which is an exposed die pad on the bottom of the device, is a metallic thermal and electrical conductor. Therefore, if not implementing PowerPAD PCB features, the use of solder masks (or other assembly techniques) may be required to prevent any inadvertent shorting by the exposed PowerPAD of connection etches or vias under the package. It is strongly recommended that the PowerPAD be soldered to the thermal land. The recommended convention, however, is to not run any etches or signal vias under the device, but to have only a grounded thermal land as explained below. Although the actual size of the exposed die pad may vary, the minimum size required for the keep out area for the 64-pin PAP PowerPAD package is 8 mm × 8 mm. It is recommended that there be a thermal land, which is an area of solder-tinned-copper, underneath the PowerPAD package. The thermal land varies in size depending on the PowerPAD package being used, the PCB construction, and the amount of heat that needs to be removed. In addition, the thermal land may or may not contain numerous thermal vias depending on PCB construction. 16 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLK2521 TLK2521 1.0 to 2.5 Gbps 18BIT 18BIT SERDES SLLS574D SLLS574D - JULY 2003 - REVISED JULY 2007 Other requirements for thermal lands and thermal vias are detailed in the TI application note PowerPAD Thermally Enhanced Package application report, TI (SLMA002 SLMA002), available via the TI Web pages beginning at URL: http://www.ti.com. Figure 13. Example of a Thermal Land For the TLK2521 TLK2521, this thermal land should be grounded to the low-impedance ground plane of the device. This improves not only thermal performance but also the electrical grounding of the device. It is also recommended that the device ground pin landing pads be connected directly to the grounded thermal land. The land size should be as large as possible without shorting device signal pins. The thermal land may be soldered to the exposed PowerPAD using standard reflow soldering techniques. While the thermal land may be electrically floated and configured to remove heat to an external heat sink, it is recommended that the thermal land be connected to the low impedance ground plane for the device. More information may be obtained from the TI application note PHY Layout, TI (SLLA020 SLLA020). POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 17 PACKAGE OPTION ADDENDUM www.ti.com 6-Jul-2009 PACKAGING INFORMATION Orderable Device Status (1) Package Type Package Drawing Pins Package Eco Plan (2) Qty TLK2521IPAP TLK2521IPAP ACTIVE HTQFP PAP 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TLK2521IPAPG4 TLK2521IPAPG4 ACTIVE HTQFP PAP 64 160 Green (RoHS & no Sb/Br) CU NIPDAU Level-3-260C-168 HR TLK2521IPAPR TLK2521IPAPR PREVIEW HTQFP PAP 64 TBD Call TI Lead/Ball Finish MSL Peak Temp (3) Call TI (1) The marketing status values are defined as follows: ACTIVE: Product device recommended for new designs. LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect. NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design. PREVIEW: Device has been announced but is not in production. Samples may or may not be available. OBSOLETE: TI has discontinued the production of the device. (2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability information and additional product content details. TBD: The Pb-Free/Green conversion plan has not been defined. Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes. Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above. Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material) (3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature. Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release. In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis. Addendum-Page 1 IMPORTANT NOTICE Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements, and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are sold subject to TI's terms and conditions of sale supplied at the time of order acknowledgment. TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where mandated by government requirements, testing of all parameters of each product is not necessarily performed. TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and applications using TI components. To minimize the risks associated with customer products and applications, customers should provide adequate design and operating safeguards. TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the third party, or a license from TI under the patents or other intellectual property of TI. Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional restrictions. Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not responsible or liable for any such statements. TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in such safety-critical applications. TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use. TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated products in automotive applications, TI will not be responsible for any failure to meet such requirements. Following are URLs where you can obtain information on other Texas Instruments products and application solutions: Products Applications Amplifiers amplifier.ti.com Audio www.ti.com/audio Data Converters dataconverter.ti.com Automotive www.ti.com/automotive DLP® Products www.dlp.com Communications and Telecom www.ti.com/communications DSP dsp.ti.com Computers and Peripherals www.ti.com/computers Clocks and Timers www.ti.com/clocks Consumer Electronics www.ti.com/consumer-apps Interface interface.ti.com Energy www.ti.com/energy Logic logic.ti.com Industrial www.ti.com/industrial Power Mgmt power.ti.com Medical www.ti.com/medical Microcontrollers microcontroller.ti.com Security www.ti.com/security RFID www.ti-rfid.com Space, Avionics & Defense www.ti.com/space-avionics-defense RF/IF and ZigBee® Solutions www.ti.com/lprf Video and Imaging www.ti.com/video Wireless www.ti.com/wireless-apps Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265 Copyright © 2010, Texas Instruments Incorporated