TLC2264 TLC2264A TLC2264Y SLOS130B TLC2264CD TLC2264CN TLC2264CPWLE TLC2264AID - Datasheet Archive

 

Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 D D D D D D

 

TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 D D D D D D Output Swing Includes Both Supply Rails Low Noise . . . 12 nV/Hz Typ at f = 1 kHz Low Input Bias Current . . . 1 pA Typ Fully Specified for Both Single-Supply and Split-Supply Operation Low Power . . . 1 mA Max D D Common-Mode Input Voltage Range Includes Negative Rail Low Input Offset Voltage 950 µV Max at TA = 25°C (TLC2264A TLC2264A) Macromodel Included EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY description Vn VN ­ Equivalent Input Noise Voltage ­ nV/ Hz nv//Hz 60 The TLC2264 TLC2264 and TLC2264A TLC2264A are quadruple VDD = 5 V operational amplifiers manufactured using TI's RS = 20 TA = 25°C Advanced LinCMOSTM process. These devices 50 exhibit rail-to-rail output performance while having better input offset voltage and lower power dissipation levels than existing CMOS operational 40 amplifiers. In addition, the noise performance (see Figure 1) has been dramatically increased for 30 this class of low-power CMOS amplifier. Figure 1 depicts the low level of voltage noise for this CMOS amplifier, which has only 200 µA (typical) 20 of supply current per amplifier. Also, the common-mode input voltage range is wider than 10 typical standard CMOS-type amplifiers. To take advantage of this improvement in performance and to make this device available for a wider range 0 of applications, VICR is specified with a larger 101 10 2 10 3 10 4 maximum input offset voltage test limit of ± 5 mV. f ­ Frequency ­ Hz The Advanced LinCMOSTM process uses a Figure 1 silicon-gate technology to obtain input offset voltage stability with temperature and time that far exceeds that obtainable using metal-gate technology. This technology also makes possible input impedance levels that meet or exceed levels offered by top-gate JFET and expensive dielectric-isolated devices. AVAILABLE OPTIONS PACKAGED DEVICES TA VIOmax AT 25°C SMALL OUTLINE (D) CHIP CARRIER (FK) CERAMIC DIP (J) PLASTIC DIP (N) TSSOP (PW) CERAMIC FLATPACK (W) 0°C to 70°C 2.5 mV TLC2264CD TLC2264CD - - TLC2264CN TLC2264CN TLC2264CPWLE TLC2264CPWLE - ­ 40°C to 125°C 950 µ µV 2.5 mV TLC2264AID TLC2264AID TLC2264ID TLC2264ID - - - - TLC2264AIN TLC2264AIN TLC2264IN TLC2264IN TLC2264AIPWLE TLC2264AIPWLE - - - ­ 55°C to 125°C 950 µV 2.5 mV - - TLC2264AMFK TLC2264AMFK TLC2264MFK TLC2264MFK TLC2264AMJ TLC2264AMJ TLC2264MJ TLC2264MJ - - - - CHIP FORM (Y) TLC2264AMW TLC2264AMW TLC2264MW TLC2264MW TLC2262Y TLC2262Y The D packages are available taped and reeled. Add R suffix to device type (e.g., TLC2264CDR TLC2264CDR). The PW package is available only left-end taped and reeled. Chips are tested at 25°C. Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet. Advanced LinCMOS is a trademark of Texas Instruments Incorporated. Copyright © 1996, Texas Instruments Incorporated PRODUCTION DATA information is current as of publication date. Products conform to specifications per the terms of Texas Instruments standard warranty. Production processing does not necessarily include testing of all parameters. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 1 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 description (continued) The TLC2264 TLC2264 and TLC2264A TLC2264A, exhibiting high input impedance and low noise, are excellent for small-signal conditioning for high-impedance sources, such as piezoelectric transducers. Because of the low-power dissipation levels, these devices work well in hand-held monitoring and remote-sensing applications. In addition, the rail-to-rail output feature with single or split supplies makes these devices excellent choices when interfacing directly to analog-to-digital converters (ADCs). All of these features, combined with its temperature performance, make the TLC2264 TLC2264 family ideal for sonobuoys, remote pressure sensors, temperature control, active voltage-resistive (VR) sensors, accelerometers, portable medical applications, hand-held metering, and many other applications. The device inputs and outputs are designed to withstand a 100-mA surge current without sustaining latch-up. In addition, internal ESD-protection circuits prevent functional failures up to 2000 V as tested under MIL-STD-883C MIL-STD-883C, Method 3015.2. Exercise care in handling these devices, as exposure to ESD may result in degradation of the device parametric performance. Additional care should be exercised to prevent VDD+ supply line transients under powered conditions. Transients greater than 20 V can trigger the ESD-protection structure, inducing a low-impedance path to VDD ­ /GND. Should this condition occur, the sustained current supplied to the device must be limited to 100 mA or less. Failure to do so could result in a latched condition and device failure. 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN ­ 4IN + VDD ­ / GND 3IN + 3IN ­ 3OUT TLC2264M TLC2264M, TLC2264AM TLC2264AM . . . J OR W PACKAGE (TOP VIEW) 1OUT 1IN ­ 1IN + VDD + 2IN + 2IN ­ 2OUT 1 14 2 13 3 12 4 11 5 10 6 9 7 8 4OUT 4IN ­ 4IN + VDD ­ / GND 3IN + 3IN ­ 3OUT 1IN + NC VCC + NC 2IN + 4 3 2 1 20 19 18 5 17 6 16 7 15 8 14 9 10 11 12 13 2IN ­ 2OUT NC 3OUT 3IN ­ 1OUT 1IN ­ 1IN + VDD + 2IN + 2IN ­ 2OUT TLC2264M TLC2264M, TLC2264AM TLC2264AM . . . FK PACKAGE (TOP VIEW) 1IN ­ 1OUT NC 4OUT 4IN ­ TLC2264C TLC2264C, TLC2264AC TLC2264AC TLC2264I TLC2264I, TLC2264AI TLC2264AI D, N, OR PW PACKAGE (TOP VIEW) 2 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 4IN + NC VCC ­ /GND NC 3IN + TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TLC2264Y TLC2264Y chip information This chip, when properly assembled, displays characteristics similar to the TLC2264C TLC2264C. Thermal compression or ultrasonic bonding may be used on the doped-aluminum bonding pads. This chip may be mounted with conductive epoxy or a gold-silicon preform. VDD+ (4) BONDING PAD ASSIGNMENTS 1IN + (3) (2) (13) (12) (11) (10) (14) (9) (8) 1IN ­ 2OUT 3 IN + (10) (9) 4OUT (1) 1OUT ­ + (7) 3IN ­ 67 + ­ + (5) (6) 2IN + 2IN ­ (8) 3OUT ­ + (14) ­ (12) 4IN + (13) 4IN ­ (11) (7) (1) (2) (3) (4) (5) (6) VDD ­ / GND CHIP THICKNESS: 15 MILS TYPICAL BONDING PADS: 4 × 4 MILS MINIMUM 109 TJmax = 150°C TOLERANCES ARE ± 10%. ALL DIMENSIONS ARE IN MILS. PIN (11) IS INTERNALLY CONNECTED TO BACKSIDE OF THE CHIP. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 3 4 IN ­ IN + Q1 Q5 R4 Q2 Q3 R3 Q4 equivalent schematic (each amplifier) Q7 Q6 Q10 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 76 18 56 6 Includes all amplifiers, ESD, bias, and trim circuitry Transistors Diodes Resistors Capacitors COMPONENT COUNT Q8 R5 Q9 R1 Q13 VDD ­ / GND Q11 R5 Q12 C1 VDD + R2 Q15 Q14 D1 Q17 Q16 OUT Template Release Date: 7­11­94 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL1996 OPERATIONAL1996 AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 absolute maximum ratings over operating free-air temperature range (unless otherwise noted) Supply voltage, VDD + (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 V Supply voltage, VDD ­ (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­ 8 V Differential input voltage, VID (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 16 V Input voltage range, VI (any input, see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . VDD ­ ­ 0.3 V to VDD+ Input current, II (each input) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 5 mA Output current, IO . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Total current into VDD + . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Total current out of VDD ­ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 50 mA Duration of short-circuit current at (or below) 25°C (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . unlimited Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table Operating free-air temperature range, TA: C suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0°C to 70°C I suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­ 40°C to 125°C M suffix . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­ 55°C to 125°C Storage temperature range, Tstg . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ­ 65°C to 150°C Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds: D, N, and PW packages . . . . . . . . . 260°C FK, J, and W packages . . . . . . . . . 300°C Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. NOTES: 1. All voltage values, except differential voltages, are with respect to the midpoint between VDD+ and VDD ­ . 2. Differential voltages are at IN+ with respect to IN ­. Excessive current flows when input is brought below VDD ­ ­ 0.3 V. 3. The output can be shorted to either supply. Temperature and /or supply voltages must be limited to ensure that the maximum dissipation rating is not exceeded. DISSIPATION RATING TABLE PACKAGE TA 25°C 25 C POWER RATING DERATING FACTOR ABOVE TA = 25°C TA = 70°C 70 C POWER RATING TA = 125 C 125°C POWER RATING D 950 mW 7.6 mW/°C 608 mW 190 mW FK 1375 mW 11.0 mW/°C - 275 mW J 1375 mW 11.0 mW/°C - 275 mW N 1150 mW 9.2 mW/°C 736 mW 230 mW PW 700 mW 5.6 mW/°C 448 mW 140 mW W 700 mW 5.5 mW/°C - 150 mW recommended operating conditions C SUFFIX MIN Supply voltage, VDD ± ± 2.2 Input voltage range, VI Common-mode input voltage, VIC VDD ­ VDD ­ Operating free-air temperature, TA MAX ±8 0 VDD + ­ 1.5 VDD + ­ 1.5 POST OFFICE BOX 655303 70 I SUFFIX MIN ± 2.2 VDD ­ VDD ­ ­ 40 · DALLAS, TEXAS 75265 MAX ±8 VDD + ­ 1.5 VDD + ­ 1.5 125 M SUFFIX MIN ± 2.2 VDD ­ VDD ­ ­ 55 MAX UNIT ±8 V VDD + ­ 1.5 VDD + ­ 1.5 V 125 °C V 5 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage VDD ± = ± 2 5 V, 2.5 V RS = 50 VIC = 0, 0 0, VO = 0 Input bias current 25°C 0.003 µV/mo 25°C 0.5 100 25°C 1 Full range RS = 50 , 100 25°C VIC = 2 5 V 2.5 V, Low-level output voltage p L l l l g IOL = 500 µA VIC = 2 5 V 2.5 V, VIC = 2 5 V 2.5 V, AVD Large-signal diff L g ig l differential voltage amplification i l l g plifi i ri(d) IOL = 1 mA IOL = 4 mA RL = 50 k VIC = 2.5 V, 25V VO = 1 V to 4 V RL = 1 M Differential input resistance V 4.82 4.70 Full range IOL = 50 µA 4.85 25°C VIC = 2.5 V, pA 4.99 Full range IOH = ­ 400 µA ­ 0.3 to 4.2 pA 0 to 3.5 25°C IOH = ­ 100 µA High-level output voltage p High l l l g 0 to 4 |VIO | 5 mV V V IOH = ­ 20 µA µV µV/°C Full range Common-mode input voltage range C d i l UNIT 2 Full g F ll range VOL 2500 3000 25°C VOH MAX 300 25 C 25°C to 70°C Input offset current VICR TYP Full range Input offset voltage long-term drift (see Note 4) IIB TLC2264C TLC2264C MIN 25°C VIO IIO TA 4.94 4.60 V 4.85 25°C 0.01 25°C 0.09 Full range 0.15 0.15 25°C 0.2 Full range 0.3 V 0.3 25°C 0.7 Full range 1 1.2 25°C 80 Full range 55 170 V/mV V/ V 25°C 550 25°C 1012 ri(c) Common-mode input resistance 25°C 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 240 25°C 70 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, VO = 2.5 V, RS = 50 Full range 70 kSVR Supply-voltage rejection ratio (VDD /VIO) VDD = 4.4 V to 16 V, VIC = VDD /2, No load 25°C 80 Full range 80 IDD Supply current (four amplifiers) VO = 2 5 V 2.5 V, 83 No load 25°C Full range dB 95 0.8 dB 1 1 mA Full range is 0°C to 70°C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 6 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER SR TEST CONDITIONS VO = 1.4 V to 2 6 V 14 2.6 V, CL = 100 pF Slew rate at unity gain Sl i i RL = 50 k, 25°C 0.35 Full range Peak-to-peak equivalent input noise voltage In 0.3 03 Total harmonic distortion plus noise 40 25°C 12 f = 0.1 Hz to 1 Hz 25°C 0.7 f = 0.1 Hz to 10 Hz 25°C 1.3 0.6 VO = 0.5 V to 2.5 V, f = 20 kHz, kHz RL = 50 k AV = 1 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL = 50 k, Maximum output-swing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF To 0 1% 0.1% Settling i S li time AV = ­ 1, Step = 0.5 V to 2.5 V, RL = 50 k, CL = 100 pF RL = 50 k, CL = 100 pF Phase margin at unity gain Gain margin V/µs V/ 25°C Equivalent input noise current THD + N MAX UNIT 0.55 25°C VN(PP) m TYP f = 1 kHz Equivalent input noise voltage ts TLC2264C TLC2264C MIN f = 10 Hz Vn BOM TA nV/Hz µV fA /Hz 0.017% 25°C AV = 10 0.03% 25°C 0.71 MHz 25°C 185 kHz 6.4 64 µs 25°C To 0 01% 0.01% 14.1 14 1 25°C 56° 25°C 11 dB Full range is 0°C to 70°C. Referenced to 2.5 V POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 7 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise specified) PARAMETER TEST CONDITIONS Input offset voltage VIO Temperature coefficient of input offset voltage 0 VIC = 0, RS = 50 3000 µV/°C 25°C 0.003 µV/mo 0.5 Full range 100 25°C 1 Full range 100 25°C 4.7 Full range IO = 500 µA VIC = 0 0, 4.6 25°C ­ 4.85 Full range Large-signal diff L g ig l differential voltage amplification i l l g plifi i ­ 4.7 ­ 4.7 IO = 1 mA Full range IO = 4 mA Full range VO = ± 4 V RL = 1 M V 4.85 ­ 4.85 25°C VIC = 0 0, RL = 50 k 4.94 ­ 4.99 25°C VIC = 0 0, Maximum negative p k output voltage M i g i peak p l g pA V 4.82 25°C IO = 50 µA 4.85 Full range IO = ­ 400 µA ­ 5.3 to 4.2 pA 4.99 25°C IO = ­ 100 µA VIC = 0, ­5 to 3.5 RS = 50 IO = ­ 20 µA Maximum p i i p k output voltage positive peak VOM + M i p l g ­5 to 4 Full F ll range g |VIO | 5 mV V mV, V Common-mode input voltage range C d i l µV 2 25°C AVD 2500 UNIT 25°C 0 VO = 0, Input bias current VOM ­ MAX 300 25 C 25°C to 70°C Input offset current VICR TYP Full range Input offset voltage long-term drift (see Note 4) IIB TLC2264C TLC2264C MIN 25°C VIO IIO TA 25°C ­4 ­ 4.91 V ­ 4.8 ­ 4.3 ­ 3.8 25°C 80 Full range 200 55 V/mV V/ V 25°C 1000 ri(d) Differential input resistance 25°C 1012 ri(c) Common-mode input resistance 25°C 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 220 VIC = ­ 5 V to 2.7 V, VO = 0, RS = 50 CMRR Common-mode rejection ratio kSVR Supply-voltage rejection ratio (VDD ± /VIO) VDD ± = ± 2.2 V to ± 8 V, VIC = 0, No load IDD Supply current (four amplifiers) VO = 0 0, No load 25°C 75 Full range 75 25°C 80 Full range 80 25°C Full range 88 dB 95 0.85 dB 1 1 mA Full range is 0°C to 70°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 8 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER SR Slew rate at unity g i Sl i y gain Vn Equivalent input noise voltage VN(PP) Peak to peak Peak-to-peak equivalent input noise voltage In Total harmonic distortion plus noise VO = ± 1 9 V 1.9 V, CL = 100 pF RL = 50 k k, Equivalent input noise current THD + N TEST CONDITIONS TA TLC2264C TLC2264C MIN TYP 25°C 0.35 0.3 03 UNIT 0.55 Full range MAX V/µs V/µ f = 10 Hz 25°C 43 f = 1 kHz 25°C 12 f = 0.1 Hz to 1 Hz 25°C 0.8 f = 0.1 Hz to 10 Hz 25°C 1.3 25°C 0.6 nV/Hz µV fA /Hz VO = ± 2.3 V, f = 20 kHz, kHz RL = 50 k AV = 1 Gain-bandwidth product f = 10 kHz, CL = 100 pF RL = 50 k, 25°C 0.73 0 73 MHz BOM Maximum output-swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF 25°C 70 kHz Settling i S li time AV = ­ 1, Step = ­ 2.3 V to 2.3 V, , RL = 50 k, CL = 100 pF To 0 1% 0.1% ts RL = 50 k k, CL = 100 pF m Phase margin at unity gain Gain margin 0.014% 25°C AV = 10 0.024% 7.1 71 µs 25°C To 0 01% 0.01% 16.5 16 5 25°C 57° 25°C 11 dB Full range is 0°C to 70°C. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 9 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Temperature coefficient p of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TLC2264I TLC2264I MIN 25°C 0.003 0.003 µV/mo 0.5 0.5 500 25°C RS = 50 , Large signal differential Large-signal voltage amplification 1 500 0 to 4 0 to 3.5 |VIO | 5 mV V V 25°C IOH = ­ 100 µA 25°C 4.85 Full range 25°C 4.7 Full range ­ 0.3 to 4.2 500 0 to 4 4.5 4.99 4.85 4.85 4.7 0.01 IOL = 500 µA 0.09 RL = 50 k VIC = 2.5 V, 25V VO = 1 V to 4 V RL = 1 M 4.94 V 4.85 4.5 25°C mA Full range 0.01 0.15 0.09 0.15 0.8 Full range 80 Full range 100 50 0.15 0.15 1 0.7 1.2 25°C V 4.82 25°C 25°C pA 4.99 4.94 IOL = 50 µA IOL = 4 ­ 0.3 to 4.2 pA 0 to 3.5 4.82 VIC = 2 5 V 2.5 V, 500 1 Full range VIC = 2 5 V 2.5 V, AVD µV µV/°C Full range VIC = 2.5 V, Low-level output L l l voltage 950 1500 UNIT 25°C VDD ± = ± 2 5 V, VIC = 0 2.5 V 0, VO = 0, RS = 50 IOH = ­ 400 µA VOL 300 MAX 2 IOH = ­ 20 µA High-level output Hi h l l voltage 2500 TYP 2 Full F ll range g VOH MIN 3000 25°C Common-mode i p C d input voltage range MAX 300 25°C to 125°C Input bias current VICR TLC2264AI TLC2264AI TYP Full range Input offset current IIB TA 25°C Input offset voltage VIO TEST CONDITIONS V 1 1.2 80 170 50 V/mV V/ V 25°C 550 550 ri(d) Differential input resistance 25°C 1012 1012 ri(c) Common-mode input resistance 25°C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 240 240 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, VO = 2.5 V, , , RS = 50 kSVR IDD Supply-voltage rejection ratio (VDD /VIO) Supply current pp y (four amplifiers) VDD = 4.4 V to 16 V, , VIC = VDD /2, No load VO = 2 5 V 2.5 V, No load 25°C 70 Full range 70 25°C 80 Full range 83 70 80 83 dB 70 95 80 95 dB 25°C Full range 80 0.8 1 1 0.8 1 1 mA Full range is ­ 40°C to 125°C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 10 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k, TA TLC2264I TLC2264I MIN TYP 25°C 0.35 0 35 0.55 0 55 Full range 0.25 0 25 TLC2264AI TLC2264AI MAX MIN TYP 0.35 0 35 MAX UNIT 0.55 0 55 Slew rate at unity Sl i gain VO = 1.4 V to 2 6 V 14 2.6 V, CL = 100 pF Vn Equivalent input noise voltage f = 10 Hz 25°C 40 40 f = 1 kHz 25°C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25°C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25°C 1.3 1.3 In Equivalent input noise current 25°C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 0.017% 0.017% THD + N 0.03% 0.03% Gain bandwidth Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25°C 0.71 0 71 0.71 0 71 MHz BOM Maximum outputoutput swing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF 25°C 185 185 kHz 6.4 64 6.4 64 Settling i S li time AV = ­ 1, Step = 0.5 V to 2.5 V, RL = 50 k, CL = 100 pF To 0 1% 0.1% ts 14.1 14 1 14.1 14 1 RL = 50 k, CL = 100 pF 25°C 56° 56° 25°C 11 11 SR m Phase margin at unity gain V/µs V/ 0.25 0 25 fA /Hz µs 25°C To 0 01% 0.01% POST OFFICE BOX 655303 µV 25°C AV = 10 Gain margin Full range is ­ 40°C to 125°C. Referenced to 2.5 V nV/Hz · DALLAS, TEXAS 75265 dB 11 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO 950 1500 UNIT µV 2 µV/°C 25°C VO = 0, 0 0.003 0.003 µV/mo 0.5 0.5 Full range 500 25°C RS = 50 , ­5 to 3.5 25°C 25°C 4.85 25°C 4.7 Full range IO = 500 µA VIC = 0, 0 VIC = 0, 0 IO = 4 mA RL = 50 k ­5 to 4 4.94 4.85 ­ 4.85 Full range 4.85 4.7 Full range ­4 25°C 80 V 4.85 ­ 4.99 ­ 4.91 ­ 4.85 ­ 4.91 V ­ 4.85 ­ 4.3 ­4 ­ 3.8 Full range 4.94 4.5 ­ 4.85 25°C V 4.82 ­ 4.99 25°C pA 4.99 4.5 25°C ­ 5.3 to 4.2 pA ­5 to 3.5 4.82 IO = 50 µA VIC = 0, ­ 5.3 to 4.2 500 4.99 Full range IO = ­ 100 µA 1 500 ­5 to 4 |VIO | 5 mV V V 500 1 Full range IO = ­ 400 µA VOM ­ 300 MAX 25°C VIC = 0, 0 RS = 50 IO = ­ 20 µA Maximum negative peak M i i k output voltage 2500 TYP 2 Full F ll range g Maximum positive peak M i ii k VOM + output voltage MIN 3000 25°C Common mode input Common-mode i C d voltage range g g MAX 300 25 C 25°C to 125°C Input bias current VICR TLC2264AI TLC2264AI TYP Full range Input offset current IIB TLC2264I TLC2264I MIN 25°C Input offset voltage VIO TA TEST CONDITIONS ­ 4.3 ­ 3.8 50 200 80 200 AVD Large-signal Large signal differential voltage amplification 25°C 1000 1000 ri(d) Differential input resistance 25°C 1012 1012 ri(c) Common-mode input resistance 25°C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, 25°C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 220 220 CMRR Common mode Common-mode rejection ratio VIC = ­ 5 V to 2.7 V, VO = 0, RS = 50 kSVR Supply voltage Supply-voltage rejection ratio (VDD ± /VIO) VDD± = ± 2.2 V to ± 8 V, VIC = VDD /2, No load IDD Supply current (four amplifiers) VO = 0 0, VO = ± 4 V RL = 1 M N package 25°C 75 Full range 75 25°C 80 Full range 80 No load 25°C Full range V/mV V/ V 50 88 75 88 dB 75 95 80 95 dB 80 0.85 1 1 0.85 1 1 mA Full range is ­ 40°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 12 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER TEST CONDITIONS TA TLC2264I TLC2264I MIN TYP 25°C 0.35 0.55 Full range 0.25 0 25 TLC2264AI TLC2264AI MAX MIN TYP 0.35 UNIT 0.55 SR Slew rate at unity gain VO = ± 1 9 V 1.9 V, CL = 100 pF Vn Equivalent input noise voltage f = 10 Hz 25°C 43 43 f = 1 kHz 25°C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25°C 0.8 0.8 VN(PP) f = 0.1 Hz to 10 Hz 25°C 1.3 1.3 In Equivalent input noise current 25°C 0.6 0.6 THD + N Total harmonic distortion plus noise VO = ± 2.3 V, RL = 50 k k, f = 20 kHz AV = 1 Gain bandwidth Gain-bandwidth product f =10 kHz, 10 CL = 100 pF RL = 50 k, BOM Maximum outputoutput swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF Settling i S li time AV = ­ 1, Step = ­ 2.3 V to 2.3 V, , RL = 50 k, CL = 100 pF To 0 1% 0.1% ts RL = 50 k, , CL = 100 p pF MAX m Phase margin at unity gain RL = 50 k k, V/µs V/µ 0.25 0 25 nV/Hz µV fA /Hz 0.014% 0.014% 0.024% 0.024% 25°C 0.73 0 73 0.73 0 73 MHz 25°C 70 70 kHz 7.1 71 7.1 71 16.5 16 5 16.5 16 5 25°C 57° 57° 25°C 11 11 25°C AV = 10 µs 25°C To 0 01% 0.01% Gain margin Full range is ­ 40°C to 125°C. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 dB 13 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD = 5 V (unless otherwise noted) PARAMETER VIO Temperature coefficient p of input offset voltage Input offset voltage long-term drift (see Note 4) IIO TLC2264M TLC2264M MIN 25°C 0.003 0.003 µV/mo 0.5 0.5 500 25°C RS = 50 , Large signal differential Large-signal voltage amplification 1 500 0 to 4 0 to 3.5 |VIO | 5 mV V V 25°C IOH = ­ 100 µA 25°C 4.85 Full range 25°C 4.7 Full range ­ 0.3 to 4.2 500 0 to 4 4.5 4.99 4.85 4.85 4.7 0.01 IOL = 500 µA 0.09 RL = 50 k VIC = 2.5 V, 25V VO = 1 V to 4 V RL = 1 M 4.94 V 4.85 4.5 25°C mA Full range 0.01 0.15 0.09 0.15 0.8 Full range 80 Full range 100 50 0.15 0.15 1 0.7 1.2 25°C V 4.82 25°C 25°C pA 4.99 4.94 IOL = 50 µA IOL = 4 ­ 0.3 to 4.2 pA 0 to 3.5 4.82 VIC = 2 5 V 2.5 V, 500 1 125°C VIC = 2 5 V 2.5 V, AVD µV µV/°C 125°C VIC = 2.5 V, Low-level output L l l voltage 950 1500 UNIT 25°C VDD ± = ± 2 5 V, VIC = 0 2.5 V 0, VO = 0, RS = 50 IOH = ­ 400 µA VOL 300 MAX 2 IOH = ­ 20 µA High-level output Hi h l l voltage 2500 TYP 2 Full F ll range g VOH MIN 3000 25°C Common-mode i p C d input voltage range MAX 300 Full range Input bias current VICR TLC2264AM TLC2264AM TYP Full range Input offset current IIB TA 25°C Input offset voltage VIO TEST CONDITIONS V 1 1.2 80 170 50 V/mV V/ V 25°C 550 550 ri(d) Differential input resistance 25°C 1012 1012 ri(c) Common-mode input resistance 25°C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 240 240 CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, VO = 2.5 V, , , RS = 50 kSVR IDD Supply-voltage rejection ratio (VDD /VIO) Supply current pp y (four amplifiers) VDD = 4.4 V to 16 V, , VIC = VDD /2, No load VO = 2 5 V 2.5 V, No load 25°C 70 Full range 70 25°C 80 Full range 83 70 80 83 dB 70 95 80 95 dB 25°C Full range 80 0.8 1 1 0.8 1 1 mA Full range is ­ 55°C to 125°C. Referenced to 2.5 V NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 14 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD = 5 V PARAMETER TEST CONDITIONS RL = 50 k, TA TLC2264M TLC2264M MIN TYP 25°C 0.35 0 35 0.55 0 55 Full range 0.25 0 25 TLC2264AM TLC2264AM MAX MIN TYP 0.35 0 35 MAX UNIT 0.55 0 55 Slew rate at unity Sl i gain VO = 0.5 V to 3 5 V 05 3.5 V, CL = 100 pF Vn Equivalent input noise voltage f = 10 Hz 25°C 40 40 f = 1 kHz 25°C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25°C 0.7 0.7 VN(PP) f = 0.1 Hz to 10 Hz 25°C 1.3 1.3 In Equivalent input noise current 25°C 0.6 0.6 Total harmonic distortion plus noise VO = 0.5 V to 2.5 V, f = 20 kHz kHz, RL = 50 k AV = 1 0.017% 0.017% THD + N 0.03% 0.03% Gain bandwidth Gain-bandwidth product f = 50 kHz, CL = 100 pF RL = 50 k, 25°C 0.71 0 71 0.71 0 71 MHz BOM Maximum outputoutput swing bandwidth VO(PP) = 2 V, RL = 50 k, AV = 1, CL = 100 pF 25°C 185 185 kHz 6.4 64 6.4 64 Settling i S li time AV = ­ 1, Step = 0.5 V to 2.5 V, RL = 50 k, CL = 100 pF To 0 1% 0.1% ts 14.1 14 1 14.1 14 1 RL = 50 k, CL = 100 pF 25°C 56° 56° 25°C 11 11 SR m Phase margin at unity gain V/µs V/ 0.25 0 25 fA /Hz µs 25°C To 0 01% 0.01% POST OFFICE BOX 655303 µV 25°C AV = 10 Gain margin Full range is ­ 55°C to 125°C. Referenced to 2.5 V nV/Hz · DALLAS, TEXAS 75265 dB 15 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at specified free-air temperature, VDD ± = ±5 V (unless otherwise noted) PARAMETER VIO Temperature coefficient of input offset voltage Input offset voltage longterm drift (see Note 4) IIO 950 1500 UNIT µV 2 µV/°C 25°C VO = 0, 0 0.003 0.003 µV/mo 0.5 0.5 125°C 500 25°C ­5 to 3.5 25°C 25°C 4.85 25°C 4.7 Full range Full range VIC = 0, 0 IO = 4 mA RL = 50 k 4.94 4.85 Full range ­4 4.85 4.7 25°C 80 4.94 V 4.85 4.5 ­ 4.99 ­ 4.91 ­ 4.85 ­ 4.91 V ­ 4.85 ­ 4.3 ­4 ­ 3.8 Full range V 4.82 ­ 4.85 25°C pA 4.99 ­ 4.99 ­ 4.85 ­ 5.3 to 4.2 pA ­5 to 3.5 4.5 25°C 25°C VIC = 0, IO = 500 µA ­5 to 4 4.82 IO = 50 µA VIC = 0, ­ 5.3 to 4.2 500 4.99 Full range IO = ­ 100 µA 1 500 ­5 to 4 RS = 50 , | |VIO | 5 mV 500 1 125°C IO = ­ 400 µA VOM ­ 300 MAX 25°C VIC = 0, 0 RS = 50 IO = ­ 20 µA Maximum negative peak M i i k output voltage 2500 TYP 2 Full F ll range g Maximum positive peak M i ii k VOM + output voltage MIN 3000 25°C Common mode input Common-mode i C d voltage range g g MAX 300 Full range Input bias current VICR TLC2264AM TLC2264AM TYP Full range Input offset current IIB TLC2264M TLC2264M MIN 25°C Input offset voltage VIO TA TEST CONDITIONS ­ 4.3 ­ 3.8 50 200 80 200 AVD Large-signal Large signal differential voltage amplification 25°C 1000 1000 ri(d) Differential input resistance 25°C 1012 1012 ri(c) Common-mode input resistance 25°C 1012 1012 ci(c) Common-mode input capacitance f = 10 kHz, N package 25°C 8 8 pF zo Closed-loop output impedance f = 100 kHz, AV = 10 25°C 220 220 CMRR Common mode Common-mode rejection ratio VIC = ­ 5 V to 2.7 V, VO = 0, RS = 50 kSVR Supply voltage Supply-voltage rejection ratio (VDD ± /VIO) VDD± = ± 2.2 V to ± 8 V, VIC = VDD /2, No load IDD Supply current (four amplifiers) VO = 0 0, VO = ± 4 V RL = 1 M 25°C 75 Full range 75 25°C 80 Full range 80 No load 25°C Full range V/mV V/ V 50 88 75 88 dB 75 95 80 95 dB 80 0.85 1 1 0.85 1 1 mA Full range is ­ 55°C to 125°C. NOTE 4: Typical values are based on the input offset voltage shift observed through 500 hours of operating life test at TA = 150°C extrapolated to TA = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV. 16 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 operating characteristics at specified free-air temperature, VDD± = ±5 V PARAMETER TEST CONDITIONS TA TLC2264M TLC2264M MIN TYP 25°C 0.35 0.55 Full range 0.25 0 25 TLC2264AM TLC2264AM MAX MIN TYP 0.35 UNIT 0.55 SR Slew rate at unity gain VO = ± 2 V V, CL = 100 pF Vn Equivalent input noise voltage f = 10 Hz 25°C 43 43 f = 1 kHz 25°C 12 12 Peak-to-peak equivalent input noise voltage f = 0.1 Hz to 1 Hz 25°C 0.8 0.8 VN(PP) f = 0.1 Hz to 10 Hz 25°C 1.3 1.3 In Equivalent input noise current 25°C 0.6 0.6 THD + N Total harmonic distortion plus noise VO = ± 2.3 V, RL = 50 k k, f = 20 kHz AV = 1 Gain bandwidth Gain-bandwidth product f =10 kHz, 10 CL = 100 pF RL = 50 k, BOM Maximum outputoutput swing bandwidth VO(PP) = 4.6 V, RL = 50 k, AV = 1, CL = 100 pF Settling i S li time AV = ­ 1, Step = ­ 2.3 V to 2.3 V, , RL = 50 k, CL = 100 pF To 0 1% 0.1% ts RL = 50 k, , CL = 100 p pF MAX m Phase margin at unity gain RL = 50 k k, V/µs V/µ 0.25 0 25 nV/Hz µV fA /Hz 0.014% 0.014% 0.024% 0.024% 25°C 0.73 0 73 0.73 0 73 MHz 25°C 70 70 kHz 7.1 71 7.1 71 16.5 16 5 16.5 16 5 25°C 57° 57° 25°C 11 11 25°C AV = 10 µs 25°C To 0 01% 0.01% Gain margin Full range is ­ 55°C to 125°C. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 dB 17 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at VDD = 5 V, TA = 25°C (unless otherwise noted) PARAMETER VIO IIO Input offset voltage IIB Input bias current Input offset current TLC2264Y TLC2264Y TEST CONDITIONS Common-mode i p voltage range C d input l g g | VIO | 5 mV, V, VOH High-level output voltage High l l p l g IOH = ­ 20 µA IOH = ­ 100 µA Low-level output voltage p L l l l g 100 pA 1 100 pA ­ 0.3 to 4.2 V 4.7 VIC = 2.5 V, VIC = 2.5 V, 4.85 0.01 0.09 80 ri(d) Differential input resistance ri(c) Common-mode input resistance ci(c) Common-mode input capacitance f = 10 kHz zo Closed-loop output impedance f = 100 kHz, CMRR Common-mode rejection ratio VIC = 0 to 2.7 V, AV = 10 VO = 2.5 V, kSVR Supply-voltage rejection ratio Supply voltage (VDD /VIO) VDD = 4 4 V to 16 V 4.4 V, VIC = VDD /2 No load /2, VO = 2.5 V, No load RL = 1 M 0.15 0.8 IOL = 4 mA RL = 50 k VIC = 2.5 V, VO = 1 V to 4 V V 4.94 IOL = 50 µA IOL = 500 µA Large signal Large-signal differential voltage amplification 18 µV 4.99 AVD IDD Supply current (four amplifiers) Referenced to 2.5 V 2500 4.85 IOH = ­ 400 µA VIC = 2.5 V, VOL MAX 0.5 0 to 4 RS = 50 UNIT TYP 300 VDD ± = ± 2 5 V, 2.5 V RS = 50 VIC = 0, 0 0, VO = 0 VICR MIN V 1 170 V/mV 550 1012 1012 POST OFFICE BOX 655303 8 · DALLAS, TEXAS 75265 pF 240 RS = 50 70 83 dB 80 95 dB 0.8 1 mA TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 electrical characteristics at VDD± = ±5 V, TA = 25°C (unless otherwise noted) PARAMETER VIO IIO Input bias current VICR Common-mode input voltage range C d i p l g g | VIO | 5 mV, V, VOM + Maximum p i i p k output voltage M i positive peak p l g ­5 to 4 RS = 50 µV 100 pA 100 pA ­ 5.3 to 4.2 V 4.99 4.85 4.7 VIC = 0, VIC = 0, IOL = 50 µA IOL = 500 µA VIC = 0, Maximum negative p k output voltage g i peak p M i l g 2500 0.5 IO = ­ 20 µA IO = ­ 100 µA IO = ­ 400 µA VOM ­ UNIT MAX 300 RS = 50 , VIC = 0, 0 VO = 0 Input offset current MIN TYP 1 Input offset voltage IIB TLC2264Y TLC2264Y TEST CONDITIONS IOL = 4 mA RL = 50 k V 4.94 4.85 ­ 4.99 ­ 4.85 ­ 3.8 ­ 4.1 80 V ­ 4.91 200 AVD Large signal Large-signal differential voltage amplification ri(d) Differential input resistance 1012 ri(c) Common-mode input resistance 1012 ci(c) Common-mode input capacitance f = 10 kHz 8 pF zo Closed-loop output impedance f = 100 kHz, Common-mode rejection ratio VIC = ­ 5 V to 2.7 V, AV = 10 VO = 0, 220 CMRR RS = 50 75 88 dB kSVR Supply-voltage rejection ratio Supply voltage (VDD ± /VIO) VDD ± = ± 2 2 V to ± 8 V 2.2 V, VIC = 0 0, No load 80 95 dB IDD Supply current (four amplifiers) VO = 0, No load VO = ± 4 V POST OFFICE BOX 655303 RL = 1 M · DALLAS, TEXAS 75265 V/mV 1000 0.85 1 mA 19 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS Table of Graphs FIGURE VIO Input offset voltage Distribution vs Common-mode input voltage 2,3 4,5 VIO Input offset voltage temperature coefficient Distribution 6,7 IIB/IIO Input bias and input offset currents vs Free-air temperature 8 VI Input voltage range vs Supply voltage vs Free-air temperature 9 10 VOH VOL High-level output voltage vs High-level output current 11 Low-level output voltage vs Low-level output current 12,13 VOM + VOM ­ Maximum positive peak output voltage vs Output current 14 Maximum negative peak output voltage vs Output current 15 VO(PP) Maximum peak-to-peak output voltage vs Frequency 16 IOS Short-circuit output current vs Supply voltage vs Free-air temperature 17 18 VO Output voltage vs Differential input voltage Differential gain vs Load resistance AVD Large-signal differential voltage amplification vs Frequency vs Free-air temperature 22, 23 24, 25 zo Output impedance vs Frequency 26, 27 CMRR Common-mode rejection ratio vs Frequency vs Free-air temperature 28 29 kSVR Supply-voltage rejection ratio vs Frequency vs Free-air temperature 30, 31 32 IDD Supply current vs Supply voltage vs Free-air temperature 33 34 SR Slew rate vs Load capacitance vs Free-air temperature 35 36 VO VO Large-signal pulse response vs Time 37, 38, 39, 40 Small-signal pulse response vs Time 41, 42, 43, 44 Vn Equivalent input noise voltage vs Frequency Input noise voltage Over a 10-second period 47 Integrated noise voltage vs Frequency 48 Total harmonic distortion plus noise vs Frequency 49 Gain-bandwidth product vs Free-air temperature Free air vs Supply voltage 50 51 m Phase margin vs Frequency vs Load capacitance 22, 23 52 Am Gain margin vs Load capacitance 53 B1 Unity-gain bandwidth vs Load capacitance 54 Overestimation of phase margin vs Load capacitance 55 THD + N 20 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 19,20 21 45, 46 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC2264 TLC2264 INPUT OFFSET VOLTAGE 20 2272 Amplifiers From 2 Wafer Lots VDD ± = ± 2.5 V TA = 25°C 16 12 8 4 0 ­ 1.6 ­ 0.8 0 0.8 VIO ­ Input Offset Voltage ­ mV 2272 Amplifiers From 2 Wafer Lots VDD ± = ± 5 V TA = 25°C 16 Percentage of Amplifiers ­ % Percentage of Amplifiers ­ % 20 DISTRIBUTION OF TLC2264 TLC2264 INPUT OFFSET VOLTAGE 12 8 4 0 ­ 1.6 1.6 ­ 0.8 0 0.8 VIO ­ Input Offset Voltage ­ mV Figure 2 Figure 3 INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE INPUT OFFSET VOLTAGE vs COMMON-MODE INPUT VOLTAGE 1 VI O ­ Input Offset Voltage ­ mV VIO VDD = 5 V RS = 50 TA = 25°C 0.5 0 VDD ± = ± 5 V RS = 50 TA = 25°C 0.5 0 ÁÁ ÁÁ VIO VI O ­ Input Offset Voltage ­ mV 1 ÁÁ ÁÁ ­ 0.5 ­1 ­1 1.6 0 1 2 3 4 5 ­ 0.5 ­1 ­6 ­5 ­4 ­3 ­2 ­1 0 VIC ­ Common-Mode Input Voltage ­ V 1 2 3 4 5 VIC ­ Common-Mode Input Voltage ­ V Figure 4 Figure 5 For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 21 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS DISTRIBUTION OF TLC2264 TLC2264 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 35 25 128 Amplifiers From 2 Wafer Lots VDD ± = ± 5 V N Package TA = 25°C to 125°C 30 Percentage of Amplifiers ­ % Percentage of Amplifiers ­ % 35 128 Amplifiers From 2 Wafer Lots VDD ± = ± 2.5 V N Package TA = 25°C to 125°C 30 DISTRIBUTION OF TLC2264 TLC2264 INPUT OFFSET VOLTAGE TEMPERATURE COEFFICIENT 20 15 10 5 25 20 15 10 5 0 0 ­5 ­4 ­3 ­2 ­1 0 1 2 3 4 5 ­5 ­4 VIO ­ Temperature Coefficient of Input Offset Voltage ­ µV / °C ­3 ­1 0 1 2 3 INPUT BIAS AND INPUT OFFSET CURRENTS vs FREE-AIR TEMPERATURE 5 INPUT VOLTAGE RANGE vs SUPPLY VOLTAGE 35 10 VDD ± = ± 2.5 V VIC = 0 VO = 0 RS = 50 RS = 50 TA = 25°C 8 25 IIB 20 15 IIO 10 5 6 4 2 0 | VIO | 5 mV ­2 ­4 ­6 ­8 ­ 10 0 25 45 65 85 105 TA ­ Free-Air Temperature ­ °C 125 2 Figure 8 3 6 7 4 5 | VDD ± | ­ Supply Voltage ­ V Figure 9 ÁÁ ÁÁ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 22 4 Figure 7 V I ­ Input Voltage Range ­ V VI IIO IIIB and IIO ­ Input Bias and Input Offset Currents ­ pA IB Figure 6 30 ­2 VIO ­ Temperature Coefficient of Input Offset Voltage ­ µV / °C POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 8 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS INPUT VOLTAGE RANGE vs FREE-AIR TEMPERATURE HIGH-LEVEL OUTPUT VOLTAGE vs HIGH-LEVEL OUTPUT CURRENT 5 6 VDD = 5 V VOH VOH ­ High-Level Output Voltage ­ V VDD = 5 V VI ­ Input Voltage Range ­ V VI 3 | VIO | 5 mV 2 1 0 ÁÁ ­1 ­ 75 ­ 55 ­ 35 ­ 15 5 25 45 65 85 TA ­ Free-Air Temperature ­ °C 105 125 5 4 TA = 125°C TA = 25°C 2 TA = ­ 40°C 1 0 500 1000 1500 2000 2500 3000 | IOH| ­ High-Level Output Current ­ µA 0 Figure 10 3500 Figure 11 LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT LOW-LEVEL OUTPUT VOLTAGE vs LOW-LEVEL OUTPUT CURRENT 1.4 1.2 1 VIC = 0 VOL ­ Low-Level Output Voltage ­ V VOL VDD = 5 V TA = 25°C VIC = 1.25 V 0.8 0.6 VIC = 2.5 V 0.4 ÁÁ ÁÁ 0.2 0 0 1 2 3 4 IOL ­ Low-Level Output Current ­ mA 5 VDD = 5 V VIC = 2.5 V 1.2 TA = 125°C 1 0.8 TA = 25°C 0.6 TA = ­ 40°C TA = ­ 55°C 0.4 ÁÁ ÁÁ VOL ­ Low-Level Output Voltage ­ V VOL TA = ­ 55°C 3 ÁÁ ÁÁ 4 0.2 0 0 1 2 3 4 5 6 IOL ­ Low-Level Output Current ­ mA Figure 12 Figure 13 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 23 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS MAXIMUM POSITIVE OUTPUT VOLTAGE vs OUTPUT CURRENT MAXIMUM NEGATIVE OUTPUT VOLTAGE vs OUTPUT CURRENT VOM VOM + ­ Maximum Positive Output Voltage ­ V VDD± = ± 5 V 5 TA = ­ 55°C 4 TA = 125°C 3 TA = 25°C 2 TA = ­ 40°C 0 0 500 1000 1500 2000 2500 3000 | IO | ­ Output Current ­ µA 3500 Figure 14 VDD ± = ± 5 V VIC = 0 ­4 TA = 125°C ­ 4.2 TA = 25°C ­ 4.4 TA = ­ 40°C TA = ­ 55°C ­ 4.6 ­ 4.8 ÁÁ ÁÁ ÁÁ 1 VOM ­ VOM ­ ­ Maximum Negative Output Voltage ­ V ­ 3.8 6 ­5 0 ÁÁ ÁÁ ÁÁ VDD± = ± 5 V 7 6 VDD = 5 V 4 3 2 1 I OS IOS ­ Short-Circuit Output Current ­ mA VO(PP) ­ Maximum Peak-to-Peak Output Voltage ­ V VO(PP) 12 RL = 10 k TA = 25°C 8 0 103 10 VID = ­ 100 mV 8 VO = 0 TA = 25°C 6 4 2 0 VID = 100 mV ­2 ­4 104 105 106 2 f ­ Frequency ­ Hz Figure 16 3 4 5 6 7 | VDD ± | ­ Supply Voltage ­ V Figure 17 ÁÁ ÁÁ ÁÁ Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 24 6 SHORT-CIRCUIT OUTPUT CURRENT vs SUPPLY VOLTAGE 10 5 5 Figure 15 MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE vs FREQUENCY 9 3 4 2 IO ­ Output Current ­ mA 1 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 8 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS SHORT-CIRCUIT OUTPUT CURRENT vs FREE-AIR TEMPERATURE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE 5 VO = 0 VDD± = ± 5 V 12 11 4 10 9 VO ­ Output Voltage ­ V IOS I OS ­ Short-Circuit Output Current ­ mA 13 VID = ­ 100 mV 8 7 1 0 VDD = 5 V RL = 50 k VIC = 2.5 V TA = 25°C 3 2 ­1 VID = 100 mV ­2 1 ­3 ­4 ­ 75 ­ 50 ­ 25 0 25 50 75 100 0 0 250 500 750 1000 ­ 1000 ­ 750 ­ 500 ­ 250 VID ­ Differential Input Voltage ­ µV 125 TA ­ Free-Air Temperature ­ °C Figure 18 Figure 19 DIFFERENTIAL GAIN vs LOAD RESISTANCE OUTPUT VOLTAGE vs DIFFERENTIAL INPUT VOLTAGE VO ­ Output Voltage ­ V 3 104 VDD± = ± 5 V VIC = 0 V RL = 50 k TA = 25°C VO(PP) = 2 V TA = 25°C Differential Gain ­ V/ mV 5 1 ­1 103 102 VDD± = ± 5 V VDD = 5 V 101 ­3 ­5 0 250 500 750 1000 ­ 1000 ­ 750 ­ 500 ­ 250 VID ­ Differential Input Voltage ­ µV 1 103 Figure 20 104 105 RL ­ Load Resistance ­ k 106 Figure 21 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 25 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY AVD ­ Large-Signal Differential AVD Voltage Amplification ­ dB 60 180° VDD = 5 V CL= 100 pF TA = 25°C 135° 40 Phase Margin 20 90° 45° Gain 0 0° ÁÁ ÁÁ ÁÁ ­ 20 m ­ Phase Margin om 80 ­ 45° ­ 40 10 3 10 4 10 5 10 6 ­ 90° 10 7 f ­ Frequency ­ Hz For curves where VDD = 5 V, all loads are referenced to 2.5 V. Figure 22 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION AND PHASE MARGIN vs FREQUENCY 60 180° VDD± = ± 5 V CL = 100 pF TA = 25°C 135° 40 Phase Margin 20 45° Gain 0 0° ÁÁ ÁÁ ÁÁ ­ 20 ­ 40 10 3 ­ 45° 10 4 10 5 10 6 f ­ Frequency ­ Hz Figure 23 26 90° POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 ­ 90° 10 7 m ­ Phase Margin om AVD ­ Large-Signal Differential AVD Voltage Amplification ­ dB 80 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 104 AVD ­ Large-Signal Differential AVD Voltage Amplification ­ V/mV VDD = 5 V VIC = 2.5 V VO = 1 V to 4 V RL = 1 M 103 RL = 50 k 102 RL = 10 k 101 ­ 75 ­ 50 ­ 25 0 25 50 75 100 TA ­ Free-Air Temperature ­ °C ÁÁ ÁÁ ÁÁ AVD ­ Large-Signal Differential AVD Voltage Amplification ­ V/mV 104 LARGE-SIGNAL DIFFERENTIAL VOLTAGE AMPLIFICATION vs FREE-AIR TEMPERATURE 125 RL = 1 M 103 RL = 50 k 102 RL = 10 k 101 ­ 75 ­ 50 ­ 25 0 25 50 75 100 TA ­ Free-Air Temperature ­ °C ÁÁ ÁÁ ÁÁ Figure 24 125 Figure 25 OUTPUT IMPEDANCE vs FREQUENCY OUTPUT IMPEDANCE vs FREQUENCY 1000 1000 VDD ± = ± 5 V TA = 25°C zo zo ­ Output Impedance ­ 0 VDD = 5 V TA = 25°C zo zo ­ Output Impedance ­ 0 VDD± = ± 5 V VIC = 0 V VO = ± 4 V 100 AV = 100 10 AV = 10 1 100 10 AV = 10 1 AV = 1 0.1 10 2 AV = 100 AV = 1 10 3 10 4 10 5 f ­ Frequency ­ Hz 10 6 0.1 10 2 Figure 26 10 3 10 4 10 5 f ­ Frequency ­ Hz 10 6 Figure 27 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 27 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS COMMON-MODE REJECTION RATIO vs FREQUENCY COMMON-MODE REJECTION RATIO vs FREE-AIR TEMPERATURE 90 CMRR ­ Common-Mode Rejection Ratio ­ dB CMRR ­ Common-Mode Rejection Ratio ­ dB 100 VDD ± = ± 5 V 80 VDD = 5 V 60 40 20 0 101 102 103 104 105 VDD ± = ± 5 V 88 86 84 VDD = 5 V 82 80 ­ 75 106 ­ 50 f ­ Frequency ­ Hz ­ 25 0 25 50 75 100 TA ­ Free-Air Temperature ­ °C Figure 28 Figure 29 SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY SUPPLY-VOLTAGE REJECTION RATIO vs FREQUENCY 100 KSVR ­ Supply-Voltage Rejection Ratio ­ dB k SVR VDD = 5 V TA = 25°C 80 kSVR + 60 kSVR ­ 40 20 0 10 2 10 3 10 4 f ­ Frequency ­ Hz 10 5 10 6 VDD ± = ± 5 V TA = 25°C 80 kSVR + 60 kSVR ­ 40 20 ÁÁ ÁÁ ÁÁ KSVR ­ Supply-Voltage Rejection Ratio ­ dB k SVR 100 ÁÁ ÁÁ ­ 20 101 0 ­ 20 101 Figure 30 10 2 10 3 10 4 f ­ Frequency ­ Hz 10 5 Figure 31 For curves where VDD = 5 V, all loads are referenced to 2.5 V .Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. 28 125 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 10 6 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS SUPPLY-VOLTAGE REJECTION RATIO vs FREE-AIR TEMPERATURE SUPPLY CURRENT vs SUPPLY VOLTAGE 110 1200 VO = 0 No Load 1000 µA IDD ­ Supply Current ­ uA I DD k SVR ­ Supply-Voltage Rejection Ratio ­ dB KSVR VDD ± = ± 2.2 V to ± 8 V VO = 0 105 100 TA = ­ 55°C 800 TA = 40°C 600 400 ÁÁ ÁÁ 95 200 90 ­ 75 0 ­ 50 ­ 25 0 25 50 75 100 125 0 1 TA ­ Free-Air Temperature ­ °C 2 Figure 32 4 5 6 7 8 Figure 33 SLEW RATE vs LOAD CAPACITANCE 1 ÁÁ ÁÁ ÁÁ 1200 VDD = 5 V AV = ­ 1 TA = 25°C VDD ± = ± 5 V VO = 0 0.8 SR ­ Slew Rate ­ V/ µ s v/us 1000 800 VDD = 5 V VO = 2.5 V 600 400 SR ­ 0.6 SR + 0.4 0.2 200 ÁÁ ÁÁ 0 ­ 75 3 | VDD ± | ­ Supply Voltage ­ V SUPPLY CURRENT vs FREE-AIR TEMPERATURE µA IDD ­ Supply Current ­ uA I DD TA = 25°C TA = 125°C ­ 50 ­ 25 0 25 50 75 100 TA ­ Free-Air Temperature ­ °C 125 0 101 Figure 34 10 2 10 3 CL ­ Load Capacitance ­ pF 10 4 Figure 35 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 29 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS SLEW RATE vs FREE-AIR TEMPERATURE INVERTING LARGE-SIGNAL PULSE RESPONSE 1.2 5 SR ­ Slew Rate ­ v/uss V/ µ VO ­ Output Voltage ­ V VO SR ­ 1 0.8 SR + 0.6 0.4 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 0.2 VDD = 5 V RL = 50 k CL = 100 pF 4 A = ­1 V TA = 25°C 3 2 1 0 0 ­ 50 ­ 25 0 25 50 75 100 TA ­ Free-Air Temperature ­ °C 125 0 2 4 6 Figure 36 2 14 16 18 20 5 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25°C 4 VO ­ Output Voltage ­ V VO VO ­ Output Voltage ­ V VO 3 12 VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE VDD ± = ± 5 V RL = 50 k CL = 100 pF AV = ­ 1 TA = 25°C 4 10 Figure 37 INVERTING LARGE-SIGNAL PULSE RESPONSE 5 8 t ­ Time ­ µs 1 0 ­1 ­2 ­3 3 2 1 ­4 ­5 0 0 2 4 6 8 10 12 t ­ Time ­ µs 14 16 18 20 0 2 Figure 38 4 6 8 10 12 14 t ­ Time ­ µs 16 18 Figure 39 Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. For curves where VDD = 5 V, all loads are referenced to 2.5 V. 30 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 20 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS INVERTING SMALL-SIGNAL PULSE RESPONSE VOLTAGE-FOLLOWER LARGE-SIGNAL PULSE RESPONSE 5 3 2 VDD = 5 V RL = 50 k CL = 100 pF AV = ­ 1 TA = 25°C 2.6 VO ­ Output Voltage ­ V VO 4 VO ­ Output Voltage ­ V VO 2.65 VDD ± = ± 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25°C 1 0 ­1 ­2 ­3 2.55 2.5 2.45 ­4 ­5 2.4 0 2 4 6 8 10 12 t ­ Time ­ µs 14 16 18 0 20 2 4 6 Figure 40 14 16 18 20 Figure 41 VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE INVERTING SMALL-SIGNAL PULSE RESPONSE VDD ± = ± 5 V RL = 50 k CL = 100 pF AV = ­ 1 TA = 25°C 50 0 ­ 50 2.65 VDD = 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25°C 2.6 VO ­ Output Voltage ­ V VO 100 VO ­ Output Voltage ­ mV VO 8 10 12 t ­ Time ­ µs 2.55 2.5 2.45 2.4 ­ 100 0 2 4 6 8 10 12 14 16 18 20 0 2 t ­ Time ­ µs Figure 42 4 6 8 10 12 t ­ Time ­ µs 14 16 18 20 Figure 43 For curves where VDD = 5 V, all loads are referenced to 2.5 V. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 31 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY VOLTAGE-FOLLOWER SMALL-SIGNAL PULSE RESPONSE 60 VDD ± = ± 5 V RL = 50 k CL = 100 pF AV = 1 TA = 25°C 50 Vn VN ­ Equivalent Input Noise Voltage ­ nV/ Hz nv//Hz VO ­ Output Voltage ­ V VO 100 0 ­ 50 ­ 100 0 2 4 6 8 10 12 t ­ Time ­ µs 14 16 18 20 VDD = 5 V RS = 20 TA = 25°C 50 40 30 20 10 0 101 10 2 10 3 f ­ Frequency ­ Hz Figure 44 Figure 45 EQUIVALENT INPUT NOISE VOLTAGE vs FREQUENCY INPUT NOISE VOLTAGE OVER A 10-SECOND 10-SECOND PERIOD 1000 VDD ± = ± 5 V RS = 20 TA = 25°C 750 Input Noise Voltage ­ nV Vn VN ­ Equivalent Input Noise Voltage ­ nv//HzHz nV/ 60 50 40 30 20 500 250 0 ­ 250 ­ 500 10 VDD = 5 V f = 0.1 Hz to 10 Hz TA = 25°C ­ 750 0 101 10 2 10 3 f ­ Frequency ­ Hz 10 4 ­ 1000 0 Figure 46 2 4 6 t ­ Time ­ s Figure 47 For curves where VDD = 5 V, all loads are referenced to 2.5 V. 32 10 4 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 8 10 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS TOTAL HARMONIC DISTORTION PLUS NOISE vs FREQUENCY THD + N ­ Total Harmonic Distortion Plus Noise ­ % INTEGRATED NOISE VOLTAGE vs FREQUENCY Integrated Noise Voltage ­ µ V 100 Calculated Using Ideal Pass-Band Filter Low Frequency = 1 Hz TA = 25°C 10 1 0.1 101 1 10 2 10 3 f ­ Frequency ­ Hz 10 4 10 5 0.1 AV = 100 0.01 AV = 10 AV = 1 VDD = 5 V RL = 50 k TA = 25°C 0.001 101 10 2 Figure 48 10 5 GAIN-BANDWIDTH PRODUCT vs SUPPLY VOLTAGE 1200 940 Gain-Bandwidth Product ­ kHz VDD = 5 V f = 10 kHz CL = 100 pF Gain-Bandwidth Product ­ kHz 10 4 Figure 49 GAIN-BANDWIDTH PRODUCT vs FREE-AIR TEMPERATURE 1000 800 600 400 ­ 75 10 3 f ­ Frequency ­ Hz f = 10 kHz RL = 50 k CL = 100 pF 900 TA = 25°C 860 820 780 740 ­ 50 ­ 25 0 25 50 75 100 125 0 1 TA ­ Free-Air Temperature ­ °C 2 3 4 5 6 7 8 | VDD ± | ­ Supply Voltage ­ V Figure 50 Figure 51 For curves where VDD = 5 V, all loads are referenced to 2.5 V. Data at high and low temperatures are applicable only within the rated operating free-air temperature ranges of the various devices. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 33 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 TYPICAL CHARACTERISTICS GAIN MARGIN vs LOAD CAPACITANCE PHASE MARGIN vs LOAD CAPACITANCE 75° 20 TA = 25°C TA = 25°C 60° 15 Gain Margin ­ dB m ­ Phase Margin om Rnull = 100 Rnull = 50 45° 30° Rnull = 20 50 k 15° 50 k VI 0° 101 Rnull = 100 10 Rnull = 50 Rnull = 20 5 VDD + Rnull = 10 Rnull ­ + CL VDD ­ Rnull = 10 Rnull = 0 10 2 10 3 CL ­ Load Capacitance ­ pF Rnull = 0 0 101 10 4 10 2 10 3 CL ­ Load Capacitance ­ pF Figure 52 Figure 53 UNITY-GAIN BANDWIDTH vs LOAD CAPACITANCE OVERESTIMATION OF PHASE MARGIN vs LOAD CAPACITANCE 1000 14° TA = 25°C 12° Overestimation of Phase Margin B1 ­ Unity-Gain Bandwidth ­ kHz TA = 25°C 800 600 ÁÁ ÁÁ ÁÁ 400 200 101 Rnull = 100 10° 8° Rnull = 50 6° 4° Rnull = 10 Rnull = 20 2° 0 10 2 10 3 CL ­ Load Capacitance ­ pF 10 4 101 Figure 54 10 2 10 3 CL ­ Load Capacitance ­ pF Figure 55 See application information 34 10 4 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 10 4 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 APPLICATION INFORMATION driving large capacitive loads The TLC2264 TLC2264 is designed to drive larger capacitive loads than most CMOS operational amplifiers. Figure 52 and Figure 53 illustrate its ability to drive loads greater than 400 pF while maintaining good gain and phase margins (Rnull = 0). A smaller series resistor (Rnull) at the output of the device (see Figure 56) improves the gain and phase margins when driving large capacitive loads. Figure 52 and Figure 53 show the effects of adding series resistances of 10 , 20 , 50 , and 100 . The addition of this series resistor has two effects: the first is that it adds a zero to the transfer function, and the second is that it reduces the frequency of the pole associated with the output load in the transfer function. The zero introduced to the transfer function is equal to the series resistance multiplied by the load capacitance. To calculate the improvement in phase margin, equation (1) can be used. m1 where: + tan­1 2 × × UGBW × R null × C L (1) + improvement in phase margin UGBW + unity-gain bandwidth frequency R null + output series resistance C L + load capacitance m1 The unity-gain-bandwidth (UGBW) frequency decreases as the capacitive load increases (see Figure 54). To use equation (1), UGBW must be approximated from Figure 54. Using equation (1) alone overestimates the improvement in phase margin as illustrated in Figure 55. The overestimation is caused by the decrease in the frequency of the pole associated with the load, providing additional phase shift and reducing the overall improvement in phase margin. The pole associated with the load is reduced by the factor calculated in equation (2). F 1 + 1 ) gm × R (2) null where: + factor reducing frequency of pole + small-signal output transconductance (typically 4.83 × 10­ 3 mhos) R null + output series resistance F gm For the TLC2264 TLC2264, the pole associated with the load is typically 6 MHz with 100-pF load capacitance. This value varies inversely with CL: at CL = 10 pF, use 60 MHz, at CL = 1000 pF, use 600 kHz, and so on. Reducing the pole associated with the load introduces phase shift, thereby reducing phase margin. This results in an error in the increase in phase margin expected by considering the zero alone [equation (1)]. Equation (3) approximates the reduction in phase margin due to the movement of the pole associated with the load. The result of this equation can be subtracted from the result of equation (1) to better approximate the improvement in phase margin. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 35 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 APPLICATION INFORMATION driving large capacitive loads (continued) m2 Where: m2 UGBW F P2 + tan­1 UGBW F × P2 ­ tan ­1 UGBW P2 + reduction in phase margin + unity-gain-bandwidth frequency + factor from equation (2) + unadjusted pole (60 MHz @ 10 pF, (3) 6 MHz @ 100 pF, etc.) Using these equations with Figure 54 and Figure 55 enables the designer to choose the appropriate output series resistance to optimize the design of circuits driving large capacitive loads. 50 k VDD + 50 k VI ­ Rnull + CL VDD ­ / GND Figure 56. Series-Resistance Circuit 36 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 APPLICATION INFORMATION macromodel information Macromodel information provided was derived using Microsim Parts TM, the model generation software used with Microsim PSpice TM. The Boyle macromodel (see Note 5) and subcircuit in Figure 57 are generated using the TLC2264 TLC2264 typical electrical and operating characteristics at TA = 25°C. Using this information, output simulations of the following key parameters can be generated to a tolerance of 20% (in most cases): D D D D D D D D D D D D Maximum positive output voltage swing Maximum negative output voltage swing Slew rate Quiescent power dissipation Input bias current Open-loop voltage amplification Unity-gain frequency Common-mode rejection ratio Phase margin DC output resistance AC output resistance Short-circuit output current limit NOTE 5: G. R. Boyle, B. M. Cohn, D. O. Pederson, and J. E. Solomon, "Macromodeling of Intergrated Circuit Operational Amplifiers", IEEE Journal of Solid-State Circuits, SC-9, 353 (1974). 99 3 VCC + 9 RSS 92 FB 10 J1 DP VC J2 IN + 11 RD1 VAD DC 12 C1 R2 ­ 53 C2 6 ­ + VLN + GCM GA VLIM 8 ­ RD2 54 4 ­ 7 60 + ­ 91 + VLP ­ HLIM ­ + + DLP 90 RO2 VB IN ­ VCC ­ ­ + ISS RP 2 3 DLN EGND + ­ RO1 DE 5 + VE OUT .SUBCKT TLC2262 TLC2262 1 2 3 4 5 C1 11 12 3.560E­12 C2 6 7 15.00E­12 DC 5 53 DX DE 54 5 DX DLP 90 91 DX DLN 92 90 DX DP 4 3 DX EGND 99 0 POLY (2) (3,0) (4,0) 0 .5 .5 FB 7 99 POLY (5) VB VC VE VLP + VLN 0 21.04E6 ­30E6 30E6 30E6 ­30E6 GA 6 0 11 12 47.12E­6 GCM 0 6 10 99 4.9E­9 ISS 3 10 DC 8.250E­6 HLIM 90 0 VLIM 1K J1 11 2 10 JX J2 12 1 10 JX R2 6 9 100.0E3 RD1 60 11 21.22E3 RD2 60 12 21.22E3 R01 8 5 120 R02 7 99 120 RP 3 4 26.04E3 RSS 10 99 24.24E6 VAD 60 4 ­.6 VB 9 0 DC 0 VC 3 53 DC .65 VE 54 4 DC .65 VLIM 7 8 DC 0 VLP 91 0 DC 1.4 VLN 0 92 DC 9.4 .MODEL DX D (IS=800.0E­18) .MODEL JX PJF (IS=500.0E­15 BETA=281E­6 + VTO= ­.065) .ENDS Figure 57. Boyle Macromodel and Subcircuit PSpice and Parts are trademarks of MicroSim Corporation. POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 37 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION D (R-PDSO-G*) PLASTIC SMALL-OUTLINE PACKAGE 14 PIN SHOWN PINS * 0.050 (1,27) 8 14 16 A MAX 0.197 (5,00) 0.344 (8,75) 0.394 (10,00) A MIN 0.189 (4,80) 0.337 (8,55) 0.386 (9,80) DIM 0.020 (0,51) 0.014 (0,35) 14 0.010 (0,25) M 8 0.244 (6,20) 0.228 (5,80) 0.008 (0,20) NOM 0.157 (4,00) 0.150 (3,81) 1 Gage Plane 7 A 0.010 (0,25) 0°­ 8° 0.044 (1,12) 0.016 (0,40) Seating Plane 0.069 (1,75) MAX 0.010 (0,25) 0.004 (0,10) 0.004 (0,10) 4040047 / B 03/95 NOTES: A. B. C. D. E. 38 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion, not to exceed 0.006 (0,15). Four center pins are connected to die mount pad. Falls within JEDEC MS-012 MS-012 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION FK (S-CQCC-N*) LEADLESS CERAMIC CHIP CARRIER 28 TERMINAL SHOWN 18 17 16 15 14 13 NO. OF TERMINALS * 12 B A 11 20 MAX MIN MAX 20 0.342 (8,69) 0.358 (9,09) 0.307 (7,80) 0.358 (9,09) 28 19 MIN 0.442 (11,23) 0.458 (11,63) 0.406 (10,31) 0.458 (11,63) 10 21 9 22 8 44 0.640 (16,26) 0.660 (16,76) 0.495 (12,58) 0.560 (14,22) 23 7 52 0.740 (18,78) 0.761 (19,32) 0.495 (12,58) 0.560 (14,22) 24 6 68 25 5 0.938 (23,83) 0.962 (24,43) 0.850 (21,6) 0.858 (21,8) 84 1.141 (28,99) 1.165 (29,59) 1.047 (26,6) 1.063 (27,0) B SQ A SQ 26 27 28 1 2 3 4 0.080 (2,03) 0.064 (1,63) 0.020 (0,51) 0.010 (0,25) 0.020 (0,51) 0.010 (0,25) 0.055 (1,40) 0.045 (1,14) 0.045 (1,14) 0.035 (0,89) 0.045 (1,14) 0.035 (0,89) 0.028 (0,71) 0.022 (0,54) 0.050 (1,27) 4040140 / C 11/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a metal lid. The terminals are gold plated. Falls within JEDEC MS-004 MS-004 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 39 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION J (R-GDIP-T*) CERAMIC DUAL-IN-LINE PACKAGE 14 PIN SHOWN PINS * 14 16 18 20 22 A MAX 0.310 (7,87) 0.310 (7,87) 0.310 (7,87) 0.310 (7,87) 0.410 (10,41) A MIN 0.290 (7,37) 0.290 (7,37) 0.290 (7,37) 0.290 (7,37) 0.390 (9,91) B MAX 0.785 (19,94) 0.785 (19,94) 0.910 (23,10) 0.975 (24,77) 1.100 (28,00) B MIN 0.755 (19,18) 0.755 (19,18) C MAX 0.280 (7,11) 0.300 (7,62) 0.300 (7,62) 0.300 (7,62) C MIN 0.245 (6,22) 0.245 (6,22) 0.245 (6,22) 0.245 (6,22) DIM B 14 8 C 1 7 0.065 (1,65) 0.045 (1,14) 0.100 (2,54) 0.070 (1,78) 0.020 (0,51) MIN 0.930 (23,62) 0.388 (9,65) A 0.200 (5,08) MAX Seating Plane 0.130 (3,30) MIN 0°­ 15° 0.100 (2,54) 0.023 (0,58) 0.015 (0,38) 0.014 (0,36) 0.008 (0,20) 4040083 / B 04/95 NOTES: A. B. C. D. E. 40 All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only on press ceramic glass frit seal only. Falls within MIL-STD-1835 MIL-STD-1835 GDIP1-T14 GDIP1-T14, GDIP1-T16 GDIP1-T16, GDIP1-T18 GDIP1-T18, GDIP1-T20 GDIP1-T20, and GDIP1-T22 GDIP1-T22 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION N (R-PDIP-T*) PLASTIC DUAL-IN-LINE PACKAGE 16 PIN SHOWN PINS * 14 16 18 20 A MAX 0.775 (19,69) 0.775 (19,69) 0.920 (23.37) 0.975 (24,77) A MIN 0.745 (18,92) 0.745 (18,92) 0.850 (21.59) 0.940 (23,88) DIM A 16 9 0.260 (6,60) 0.240 (6,10) 1 8 0.070 (1,78) MAX 0.035 (0,89) MAX 0.310 (7,87) 0.290 (7,37) 0.020 (0,51) MIN 0.200 (5,08) MAX Seating Plane 0.125 (3,18) MIN 0.100 (2,54) 0°­ 15° 0.021 (0,53) 0.015 (0,38) 0.010 (0,25) M 0.010 (0,25) NOM 14/18 PIN ONLY 4040049/C 4040049/C 08/95 NOTES: A. All linear dimensions are in inches (millimeters). B. This drawing is subject to change without notice. C. Falls within JEDEC MS-001 MS-001 (20 pin package is shorter then MS-001 MS-001.) POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 41 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION PW (R-PDSO-G*) PLASTIC SMALL-OUTLINE PACKAGE 14 PIN SHOWN 0,32 0,19 0,65 14 0,13 M 8 0,15 NOM 4,50 4,30 6,70 6,10 Gage Plane 0,25 1 7 0°­ 8° 0,75 0,50 A Seating Plane 1,20 MAX 0,10 0,10 MIN PINS * 8 14 16 20 24 28 A MAX 3,10 5,10 5,10 6,60 7,90 9,80 A MIN 2,90 4,90 4,90 6,40 7,70 9,60 DIM 4040064 / D 10/95 NOTES: A. B. C. D. 42 All linear dimensions are in millimeters. This drawing is subject to change without notice. Body dimensions do not include mold flash or protrusion not to exceed 0,15. Falls within JEDEC MO-153 MO-153 POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 TLC2264 TLC2264, TLC2264A TLC2264A, TLC2264Y TLC2264Y Advanced LinCMOSTM RAIL-TO-RAIL QUADRUPLE OPERATIONAL AMPLIFIERS SLOS130B SLOS130B ­ DECEMBER 1993 ­ REVISED MAY 1996 MECHANICAL INFORMATION W (R-GDFP-F16 R-GDFP-F16) CERAMIC DUAL FLATPACK Base and Seating Plane 0.285 (7,24) 0.245 (6,22) 0.006 (0,15) 0.004 (0,10) 0.085 (2,16) 0.045 (1,14) 0.045 (1,14) 0.026 (0,66) 0.305 (7,75) 0.275 (6,99) 0.355 (9,02) 0.235 (5,97) 1 0.355 (9,02) 0.235 (5,97) 16 0.019 (0,48) 0.015 (0,38) 0.050 (1,27) 0.440 (11,18) 0.371 (9,42) 0.025 (0,64) 0.015 (0,38) 8 9 1.025 (26,04) 0.745 (18,92) 4040180-3 / B 03/95 NOTES: A. B. C. D. E. All linear dimensions are in inches (millimeters). This drawing is subject to change without notice. This package can be hermetically sealed with a ceramic lid using glass frit. Index point is provided on cap for terminal identification only. Falls within MIL-STD-1835 MIL-STD-1835 GDFP1-F16 GDFP1-F16 and JEDEC MO-092AC MO-092AC POST OFFICE BOX 655303 · DALLAS, TEXAS 75265 43 IMPORTANT NOTICE Texas Instruments (TI) reserves the right to make changes to its products or to discontinue any semiconductor product or service without notice, and advises its customers to obtain the latest version of relevant information to verify, before placing orders, that the information being relied on is current. TI warrants performance of its semiconductor products and related software to the specifications applicable at the time of sale in accordance with TI's standard warranty. Testing and other quality control techniques are utilized to the extent TI deems necessary to support this warranty. Specific testing of all parameters of each device is not necessarily performed, except those mandated by government requirements. Certain applications using semiconductor products may involve potential risks of death, personal injury, or severe property or environmental damage ("Critical Applications"). TI SEMICONDUCTOR PRODUCTS ARE NOT DESIGNED, INTENDED, AUTHORIZED, OR WARRANTED TO BE SUITABLE FOR USE IN LIFE-SUPPORT APPLICATIONS, DEVICES OR SYSTEMS OR OTHER CRITICAL APPLICATIONS. Inclusion of TI products in such applications is understood to be fully at the risk of the customer. Use of TI products in such applications requires the written approval of an appropriate TI officer. Questions concerning potential risk applications should be directed to TI through a local SC sales office. In order to minimize risks associated with the customer's applications, adequate design and operating safeguards should be provided by the customer to minimize inherent or procedural hazards. TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or services described herein. Nor does TI warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or other intellectual property right of TI covering or relating to any combination, machine, or process in which such semiconductor products or services might be or are used. Copyright © 1996, Texas Instruments Incorporated