500 MILLION PARTS FROM 12000 MANUFACTURERS
ZL30414 GR-253CORE OC-192 OC-48 OC-12 STM64 STM-16 ZL30414QGC GR-253-CORE - Datasheet Archive
ZL30414 ZL30414 SONET/SDH Clock Multiplier PLL Data Sheet Features July 2003 · Meets jitter requirements of Telcordia GR-253CORE GR-253CORE for OC-192 OC-192, OC-48 OC-48, OC-12 OC-12, and OC-3 rates · Meets jitter requirements of ITU-T G.813 for STM64 STM64, STM-16 STM-16, STM-4 and STM-1 rates · Provides four LVPECL differential output clocks at 622.08 MHz · Provides a CML differential clock at 155.52 MHz · Provides a single-ended CMOS clock at 19.44 MHz · Lock Indicator · Provides enable/disable control of output clocks · Accepts a CMOS reference at 19.44 MHz · 3.3 V supply Ordering Information ZL30414QGC ZL30414QGC -40°C to +85°C Description The ZL30414 ZL30414 is an analog phase-locked loop (APLL) designed to provide jitter attenuation and rate conversion for SDH (Synchronous Digital Hierarchy) and SONET (Synchronous Optical Network) networking equipment. The ZL30414 ZL30414 generates very low jitter clocks that meet the jitter requirements of Telcordia GR-253-CORE GR-253-CORE OC-192 OC-192, OC-48 OC-48, OC-12 OC-12, OC3 rates and ITU-T G.813 STM-64 STM-64, STM-16 STM-16, STM-4 and STM-1 rates. Applications · The ZL30414 ZL30414 accepts a CMOS compatible reference at 19.44 MHz and generates four LVPECL differential output clocks at 622.08 MHz, a CML differential clock at 155.52 MHz and a single-ended CMOS clock at 19.44 MHz. The output clocks can be individually enabled or disabled. The ZL30414 ZL30414 provides a LOCK indication. SONET/SDH line cards · 64 Pin TQFP Network Element timing cards C622oEN-A C622oEN-B C622oEN-C C622oEN-D LPF C622oP/N-A C19i Frequency & Phase Detector Loop Filter VCO Frequency Dividers and Clock Drivers 19.44MHz State Machine Reference and Bias Circuit LOCK BIAS C622oP/N-B C622oP/N-C C622oP/N-D C155oP/N C19o VDD GND VCC C155oEN C19oEN 05 Figure 1 - Functional Block Diagram 1 Zarlink Semiconductor Inc. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved. ZL30414 ZL30414 GND C622oN-A C622oP-A VCC GND C622oP-B C622oN-B VCC GND C622oN-C C622oP-C VCC GND C622oP-D C622oN-D VCC Data Sheet GND VCC1 VCC C155oN C155oP GND VCC2 LPF GND GND BIAS C155oEN C622oEN-A C622oEN-B C622oEN-C C622oEN-D 64 62 60 58 56 54 52 50 48 2 65 - EP_GND 46 4 44 6 42 8 ZL30414 ZL30414 40 10 38 12 36 14 34 16 20 22 24 26 28 30 32 GND VDD NC NC NC VDD IC NC NC C19oEN GND C19i VDD GND VDD GND 18 GND VCC VDD GND VCC GND VDD GND NC GND GND LOCK GND C19o VDD GND Figure 2 - TQFP 64 pin (Top View) Pin Description Pin Description Table Pin # Name Description 1 GND Ground. 0 volt. 2 VCC1 Positive Analog Power Supply. +3.3V ±10%. 3 VCC Positive Analog Power Supply. +3.3V ±10%. 4 5 C155oN C155oP 6 GND Ground. 0 volt 7 VCC2 Positive Analog Power Supply. +3.3V ±10% 8 LPF Low Pass Filter (Analog). Connect to this pin external RC network (RF and CF) for the low pass filter. 9 GND Ground. 0 volt 10 GND Ground. 0 volt. C155 Clock Output (CML). These outputs provide a differential 155.52 MHz clock. 2 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet Pin Description Table (continued) Pin # Name 11 BIAS 12 Description Bias. See Figure 12 for the recommended bias circuit. C155oEN C155o Clock Enable (CMOS Input). If tied high this control pin enables the C155oP/N differential driver. Pulling this input low disables the output clock and deactivates differential drivers. 13 C622oEN-A C622 Clock Output Enable A (CMOS Input). If tied high this control pin enables the C622oP/N-A output clock. Pulling this input low disables the output clock without deactivating differential drivers. 14 C622oEN-B C622 Clock Output Enable B (CMOS Input). If tied high this control pin enables the C622oP/N-B output clock. Pulling this input low disables the output clock without deactivating differential drivers. 15 C622oEN-C C622 Clock Output Enable C (CMOS Input). If tied high this control pin enables the C622oP/N-C output clock.Pulling this input low disables the output clock without deactivating differential drivers. 16 C622oEN-D C622 Clock Output Enable D (CMOS Input). If tied high this control pin enables the C622oP/N-D output clock.Pulling this input low disables the output clock without deactivating differential drivers. 17 GND Ground. 0 volt 18 VDD Positive Digital Power Supply. +3.3V ±10% 19 NC No internal bonding Connection. Leave unconnected. 20 NC No internal bonding Connection. Leave unconnected. 21 NC No internal bonding Connection. Leave unconnected. 22 VDD 23 IC Internal Connection. Connect this pin to Ground (GND). 24 NC No internal bonding Connection. Leave unconnected. 25 NC No internal bonding Connection. Leave unconnected. 26 C19oEN 27 Positive Digital Power Supply. +3.3V ±10% C19o Output Enable (CMOS Input). If tied high this control pin enables the C19o output clock. Pulling this pin low forces output driver into a high impedance state. GND Ground. 0 volt. C19i C19 Reference Input (CMOS Input). This pin is a single-ended input reference source used for synchronization. This pin accepts 19.44 MHz. 29 VDD Positive Digital Power Supply. +3.3V ±10% 30 GND Ground. 0 volt. 31 VDD Positive Digital Power Supply. +3.3V ±10% 32 GND Ground. 0 volt. 28 3 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet Pin Description Table (continued) Pin # Name 33 GND Ground. 0 volt 34 VDD Positive Digital Power Supply. +3.3V ±10% C19o C19 Clock Output (CMOS Output). This pin provides a single-ended CMOS clock at 19.44 MHz. 36 GND Ground. 0 volt. 37 LOCK Lock Indicator (CMOS Output). This output goes high when PLL is frequency locked to the input reference C19i. 38 GND Ground. 0 volt. 39 GND Ground. 0 volt. 40 NC 41 GND Ground. 0 volt. 42 VDD Positive Digital Power Supply. +3.3V ±10% 43 GND Ground. 0 volt. 44 VCC Positive Analog Power Supply. +3.3V ±10% 45 GND Ground. 0 volt. 46 VDD Positive Digital Power Supply. +3.3V ±10% 47 VCC Positive Analog Power Supply. +3.3V ±10% 48 GND Ground. 0 volt. 49 VCC Positive Analog Power Supply. +3.3V ±10%. 35 50 51 C622oN-D C622oP-D Description No internal bonding Connection. Leave unconnected. C622 Clock Output (LVPECL). These outputs provide a differential LVPECL clock at 622.08 MHz. Unused LVPECL port should be left unterminated to decrease supply current. 52 GND Ground. 0 volt 53 VCC Positive Analog Power Supply. +3.3V ±10%. 54 55 C622oP-C C622oN-C C622 Clock Output (LVPECL). These outputs provide a differential LVPECL clock at 622.08 MHz. Unused LVPECL port should be left unterminated to decrease supply current. 56 GND Ground. 0 volt. 57 VCC Positive Analog Power Supply. +3.3V ±10%. 58 59 C622oN-B C622oP-B C622 Clock Output (LVPECL). These outputs provide a differential LVPECL clock at 622.08 MHz. Unused LVPECL port should be left unterminated to decrease supply current. 4 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet Pin Description Table (continued) Pin # 60 GND Ground. 0 volt 61 VCC Positive Analog Power Supply. +3.3V ±10%. 62 63 C622oP-A C622oN-A 64 GND 65 1.0 Name Description NC C622 Clock Output (LVPECL). These outputs provide a differential LVPECL clock at 622.08 MHz. Unused LVPECL port should be left unterminated to decrease supply current. Ground. 0 volt No internal bonding Connection. Leave unconnected. Functional Description The ZL30414 ZL30414 is an analog phased-locked loop which provides rate conversion and jitter attenuation for SONET/SDH OC-192/STM-64 OC-192/STM-64, OC-48/STM-16 OC-48/STM-16, OC-12/STM-4 OC-12/STM-4 and OC-3/STM-1 applications. A functional block diagram of the ZL30414 ZL30414 is shown in Figure 1 and a brief description is presented in the following sections. 1.1 Frequency/Phase Detector The Frequency/Phase Detector compares the frequency/phase of the input reference signal with the feedback signal from the Frequency Divider circuit and provides an error signal corresponding to the frequency/phase difference between the two. This error signal is passed to the Loop Filter circuit. 1.2 Lock Indicator The ZL30414 ZL30414 has a built-in LOCK detector that measures frequency difference between input reference clock C19i and the VCO frequency. When the VCO frequency is less than ±300 ppm apart from the input reference frequency then the LOCK pin is set high. The LOCK pin is pulled low if the frequency difference exceeds ±1000 ppm. 1.3 Loop Filter The Loop Filter is a low pass filter. This low pass filter ensures that the network jitter requirements are met for an input reference frequency of 19.44 MHz. The corner frequency of the Loop Filter is configurable with an external capacitor and resistor connected to the LPF pin and ground as shown in Figure 3. ZL30414 ZL30414 Frequency and Phase Detector LPF Loop RF Filter VCO RF=8.2 k, CF=470 nF CF Figure 3 - Loop Filter Elements 5 Zarlink Semiconductor Inc. ZL30414 ZL30414 1.4 Data Sheet VCO The voltage-controlled oscillator (VCO) receives the filtered error signal from the Loop Filter, and based on the voltage of the error signal generates a primary frequency. The VCO output is connected to the "Frequency Dividers and Clock Drivers" block that divides VCO frequency and buffer generated clocks. 1.5 Output Interface Circuit The output of the VCO is used by the Output Interface Circuit to provide four LVPECL differential clocks at 622.08 MHz, one CML differential clock at 155.52 MHz and a single-ended 19.44 MHz output clock. This block provides also a 19.44MHz feedback clock that closes PLL loop. Each output clock can be enabled or disabled individually with the associated Output Enable pin. Output Clocks Output Enable Pins C622oP/N-A C622oEN-A C622oP/N-B C622oEN-B C622oP/N-C C622oEN-C C622oP/N-D C622oEN-D C155oP/N C155oEN C19o C19oEN Table 1 - Output Enable Control To reduce power consumption and achieve the lowest possible intrinsic jitter the unused output clocks must be disabled. If any of the LVPECL outputs are disabled they must be left open without any terminations. 6 Zarlink Semiconductor Inc. ZL30414 ZL30414 2.0 Data Sheet ZL30414 ZL30414 Performance The following are some of the ZL30414 ZL30414 performance indicators that complement results listed in the Characteristics section of this data sheet. 2.1 Input Jitter Tolerance Jitter tolerance is a measure of the PLL's ability to operate properly (i.e., remain in lock and/or regain lock in the presence of large jitter magnitudes at various jitter frequencies) when jitter is applied to its input reference. The input jitter tolerance of the ZL30414 ZL30414 is shown in Figure 4. On this graph, the single line at the top represents measured input jitter tolerance and the three overlapping lines below represent minimum input jitter tolerance for OC-192 OC-192, OC-48 OC-48, and OC-12 OC-12 network interfaces. The jitter tolerance is expressed in picoseconds (pk-pk) to accommodate requirements for interfaces operating at different rates. Figure 4 - Input Jitter Tolerance 7 Zarlink Semiconductor Inc. ZL30414 ZL30414 2.2 Data Sheet Jitter Transfer Characteristic Jitter Transfer Characteristic represents a ratio of the jitter at the output of a PLL to the jitter applied to the input of a PLL. This ratio is expressed in dB and it characterizes the PLLs ability to attenuate (filter) jitter. The jitter transfer characteristic for the ZL30414 ZL30414 configured with recommended loop filter components (RF=8.2 k, CF=470 nF) is shown in Figure 5. The plotted curves represent jitter transfer characteristics over the recommended voltage (3.0V to 3.6V) and temperature (-40C to 85C) ranges. Figure 5 - Jitter Transfer Characteristic 8 Zarlink Semiconductor Inc. ZL30414 ZL30414 3.0 Applications 3.1 Data Sheet Ultra-low jitter SONET/SDH equipment clocks The ZL30414 ZL30414 functionality and performance complements the entire family of the Zarlink's advanced network synchronization PLLs. Its superior jitter filtering characteristics exceed requirements of SONET/SDH optical interfaces operating up to OC-192/STM-64 OC-192/STM-64 rate (10 Gbit/s). The ZL30414 ZL30414 in combination with the MT90401 MT90401 or the ZL30407 ZL30407 (SONET/SDH Network Element PLLs) provides the core building blocks for high quality equipment clocks suitable for network synchronization (see Figure 6) . C622oA 622.08 MHz LVPECL 622.08 MHz C622oD ZL30414 ZL30414 622.08 MHz LVPECL C622oC C19i LVPECL C622oB LVPECL 622.08 MHz CML 155.52 MHz C155o C19o CMOS C19o SEC CMOS C155o PRI Synchronization Reference Clocks 19.44 MHz C19oEN C155oEN C622oEN-D RF C622oEN-C LOCK C622oEN-A CF C622oEN-B LPF LVDS 19.44 MHz 155.52 MHz C34o/C44o C16o PRIOR SECOR 6.312 MHz CMOS 4.096 MHz CMOS 2.048 MHz C1.5o MT90401 MT90401 CMOS C4o or 8.192 MHz C6o ZL30407 ZL30407 16.384 MHz CMOS C2o RefAlign CMOS C8o RefSel CMOS CMOS 1.544 MHz F16o CMOS D0 - D7 A0 - A6 CS R/W DS C20i CMOS F0o 20 MHz OCXO CMOS F8o LOCK HOLDOVER Data Port uP Controller Port Note: Only main functional connections are shown Figure 6 - SONET/SDH Equipment Clock 9 Zarlink Semiconductor Inc. 34.368 MHz or 44.736 MHz 8 kHz 8 kHz 8 kHz ZL30414 ZL30414 Data Sheet The ZL30414 ZL30414 in combination with the MT9046 MT9046 provides an optimum solution for SONET/SDH line cards (see Figure 7). C622oA 622.08 MHz LVPECL 622.08 MHz C622oD ZL30414 ZL30414 622.08 MHz LVPECL C622oC C19i LVPECL C622oB LVPECL 622.08 MHz CML 155.52 MHz C155o C19o CMOS 19.44 MHz C19oEN C155oEN C622oEN-D C622oEN-C C2 C622oEN-B R1 C1 LOCK R1 = 680 C1 = 820 nF C2 = 22 nF C622oEN-A LPF C19o Synchronization Reference Clocks CMOS 16.384 MHz C8o SEC CMOS C16o PRI CMOS 8.192 MHz 19.44 MHz C6o 6.312 MHz CMOS 4.096 MHz C2o CMOS 2.048 MHz C1.5o MT9046 MT9046 LOCK HOLDOVER CMOS C4o RSEL CMOS 1.544 MHz 8 kHz F16o CMOS TCLR PCCi FLOCK FS2 FS1 MS1 MS2 20 MHz TCXO CMOS F0o C20i CMOS F8o uC Hardware Control Note: Only main functional connections are shown Figure 7 - SONET/SDH Line Card 10 Zarlink Semiconductor Inc. 8 kHz 8 kHz ZL30414 ZL30414 3.2 3.2.1 Data Sheet Recommended Interface circuit LVPECL to LVPECL Interface The C622oP/N-A, C622oP/N-B, C622oP/N-B, and C622oP/N-D outputs provide differential LVPECL clocks at 622.08 MHz. The LVPECL output drivers require a 50 termination connected to the Vcc-2V source for each output terminal at the terminating end as shown below. The terminating resistors should be placed as close as possible to the LVPECL receiver. +3.3V 0.1uF ZL30414 ZL30414 VCC=+3.3V VCC R1 R2 LVPECL Driver R1 R2 Z=50 C622oP-A LVPECL Receiver Z=50 622.08 MHz C622oN-A GND Typical resistor values: R1 = 130, R2 =82 Figure 8 - LVPECL to LVPECL Interface 3.2.2 CML to CML Interface The C155o output provides a differential CML/LVDS compatible clock at 155.52 MHz. The output drivers require a 50 load at the terminating end if the receiver is CML type. +3.3V 0.1uF ZL30414 ZL30414 CML Driver Low impedance DC bias source VCC 0.1uF Z=50 C155oP 50 Z=50 155.52 MHz C155oN 0.1uF GND Figure 9 - CML to CML Interface 11 Zarlink Semiconductor Inc. 50 CML Receiver ZL30414 ZL30414 3.2.3 Data Sheet CML to LVDS Interface To configure the driver as an LVDS driver, external biasing resistors are required to set up the common mode voltage as specified by ANSI/TIA/EIA-644 ANSI/TIA/EIA-644 LVDS standard. The standard specifies the VCM (common mode voltage) as minimum 1.125V, typical 1.2V, and maximum 1.375V. The following figure provides a recommendation for LVDS applications. +3.3V 0.1uF ZL30414 ZL30414 VCC=+3.3V VCC CML Driver 10nF Z=50 C155oP R1 R1 100 Z=50 155.52 MHz LVDS Receiver C155oN 10nF R2 R2 GND Typical resistor values: R1 = 16k, R2 = 10k Figure 10 - LVDS Termination 3.2.4 CML to LVPECL Interface The CML output can drive LVPECL input as is shown in Figure 11. The terminating resistors should be placed as close as possible to the LVPECL receiver. +3.3V 0.1uF ZL30414 ZL30414 VCC=+3.3V VCC C155oP Z=50 R1 R1 R2 CML Driver 10nF R2 Z=50 155.52 MHz C155oN 10nF GND Typical resistor values: R1 = 82, R2 =130 Figure 11 - CML to LVPECL Interface 12 Zarlink Semiconductor Inc. LVPECL Receiver ZL30414 ZL30414 3.3 Data Sheet Power supply and BIAS circuit filtering recommendations Figure 12 presents a complete filtering arrangement that is recommended for applications requiring maximum jitter performance. The level of required filtering is subject to further optimization and simplification. Please check Zarlink's web site for updates. 0.1uF 0.1uF 0.1uF 0.1uF 0.1uF 4.7 VCC GND VCC GND VCC GND 0.1uF GND Ferrite Bead VCC GND +3.3V Power Rail 64 62 60 58 56 54 52 50 0.1uF 10uF 0.1uF 33uF VCC1 VCC + 0.1uF 33uF 220 0.1uF BIAS + 33uF 0.1uF VCC 2 4 VCC2 + 46 44 + GND VCC VDD 48 GND 6 GND GND 42 8 0.1uF VDD 0.1uF GND ZL30414 ZL30414 GND 10 GND 0.1uF 40 GND GND 38 11 12 GND 36 14 34 16 26 0.1uF 28 0.1uF 30 32 0.1uF GND VDD GND 24 VDD 22 GND 20 VDD GND VDD 18 VDD GND 0.1uF Notes: 1. All the ground pins (GND) and the Exposed die Pad (metal area at the back of the package) are connected to the same ground plane. 2. Select Ferrite Bead with IDC > 400mA and RDC in a range from 0.10 to 0.15 Figure 12 - Power Supply and BIAS circuit filtering 13 Zarlink Semiconductor Inc. ZL30414 ZL30414 4.0 Data Sheet Characteristics Absolute Maximum Ratings Characteristics Sym Min Max Units VDDR, VCCR TBD TBD V 1 Supply voltage 2 Voltage on any pin VPIN -0.5 VCC + 0.5 VDD + 0.5 V 3 Current on any pin IPIN -0.5 30 mA 4 ESD Rating 1250 V 5 Storage temperature TST 125 °C 6 Package power dissipation PPD 1.8 W VESD -55 Voltages are with respect to ground unless otherwise stated. Exceeding these values may cause permanent damage. Functional operation under these conditions is not implied. Recommended Operating Conditions Characteristics 1 Operating Temperature 2 Positive Supply Sym Min Typ Max Units TOP -40 25 +85 °C VDD, VCC 3.0 3.3 3.6 V Max Units Notes Notes Voltages are with respect to ground unless otherwise stated. Typical figures are for design aid only: not guaranteed and not subject to production testing. DC Electrical Characteristics Characteristics Sym Min Typ 1 Supply Current IDD+ICC 146 mA LVPECL, CML drivers disabled and unterminated 2 Incremental Supply Current to single LVPECL driver (driver enabled and terminated, see Figure 8) ILVPECL 37 mA Note 1 Note 2 3 Incremental Supply Current to CML driver (driver enabled and terminated, see Figure 9) ICML 26 mA Note 3 4 CMOS: High-level input voltage VIH 0.7VDD VDD V 5 CMOS: Low-level input voltage VIL 0 0.3VDD V 6 CMOS: Input leakage current IIL 5 uA 1 14 Zarlink Semiconductor Inc. VI = VDD or 0V ZL30414 ZL30414 Data Sheet DC Electrical Characteristics (continued) Characteristics Sym Min Typ Max Units Notes 7 CMOS: Input bias current for pulled-down inputs: C622oEN-A, C622oEN-C, C622oEN-D, OC-CLKoEN IB-PU 300 uA VI = VDD 8 CMOS: Input bias current for pulled-up inputs: , C622oEN-B, C19oEN IB-PD 90 uA VI = 0V 9 CMOS: High-level output voltage VOH V IOH = 8 mA 10 CMOS: Low-level output voltage VOL V IOL = 4 mA 11 LOCK pin: High-level output voltage VOH 12 LOCK pin: Low-level output voltage VOL 13 CMOS: C19o output rise time TR 1.8 3.3 ns 18 pF load 14 CMOS: C19o output fall time TF 1.1 1.4 ns 18 pF load 15 LVPECL: Differential output voltage (622.08 MHz) IVOD_LVPECLI 1.17 V Note 2 16 LVPECL: Offset voltage (622.08 MHz) V Note 2 17 LVPECL: Output rise/fall times (622.08 MHz) 18 CML: Differential output voltage (155.52 MHz) 19 CML: Offset voltage (155.52 MHz) 20 CML: Output rise/fall times (155.52 MHz) - 2.4 0.4 2.4 IOH = 0.5 mA 0.4 Vcc1.31 VOS_LVPECL Vcc1.20 Vcc1.09 IOL = 0.5 mA TRF 170 ps Note 2 IVOD_CMLI 0.73 V Note 3 V Note 3 ps Note 3 VOS_CML Vcc0.58 TRF Vcc0.54 Vcc0.50 220 : Voltages are with respect to ground unless otherwise stated. :Typical figures are for design aid only: not guaranteed and not subject to production testing. Supply voltage and operating temperature are as per Recommended Operating Conditions Note 1: The ILVPECL current is determined by the termination network connected to LVPECL outputs. More than 25% of this current flows outside the chip and it does not contribute to the internal power dissipation. Note 2: LVPECL outputs terminated with ZT = 50 resistors biased to VCC-2V (see Figure 8) Note 3: CML outputs terminated with ZT = 50 resistors connected to low impedance DC bias voltage source (see Figure 9) 15 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet AC Electrical Characteristics - Output Timing Parameters Measurement Voltage Levels Characteristics Sym CMOS LVPECL CML Units VT-CMOS VT-LVPECL VT-CML 0.5VDD 0.5VOD_LVPECL 0.5VOD_CML V 1 Threshold Voltage 2 Rise and Fall Threshold Voltage High VHM 0.7VDD 0.8VOD_LVPECL 0.8VOD_CML V 3 Rise and Fall Threshold Voltage Low VLM 0.3VDD 0.2VOD_LVPECL 0.2VOD_CML V Voltages are with respect to ground unless otherwise stated. Timing Reference Points VHM VT VLM All Signals tIF, tOF tIR, tOR Figure 13 - Output Timing Parameter Measurement Voltage Levels 16 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet AC Electrical Characteristics - C19i Input to C19o, C155o and C622o Output Timing Characteristics Sym Min Typ Max Units 1 C19i to C19o delay tC19D 6.2 7.2 8.2 ns 2 C19i to C155o delay tc155D 3 4 5 ns 3 C19i to C622oA delay tC622D 0 0.8 1.6 ns 4 C155o duty cycle dC155L 48 50 52 % 5 C622o duty cycle dC622L 48 50 52 Notes % Supply voltage and operating temperature are as per Recommended Operating Conditions Typical figures are for design aid only: not guaranteed and not subject to production testing. C19i VT-CMOS (19.44MHz) tC19D C19o VT-CMOS (19.44MHz) tC155D C155o VT-CML (155.52MHz) tC622D C622oA VT-LVPECL (622.08MHz) Figure 14 - C19i Input to C19o, C155o and C622o Output Timing 17 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet AC Electrical Characteristics- C622 Clocks Output Timing Sym Characteristics Min Typ Max Units 1 C622oA to C622oB tC622D-AB -50 0 +50 ps 2 C622oA to C622oC tC622D-AC -50 0 +50 ps 3 C622oA to C622oD tC622D-AD -50 0 +50 Notes ps Supply voltage and operating temperature are as per Recommended Operating Conditions Typical figures are for design aid only: not guaranteed and not subject to production testing. C622oA VT-LVPECL tC622D-AB VT-LVPECL C622oB tC622D-AC VT-LVPECL C622oC tC622D-AD C622oD VT-LVPECL Note: All output clocks have nominal 50% duty cycle. Figure 15 - C622oB, C622oC, C622oD Outputs Timing 18 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet Performance Characteristics - Functional (VCC = 3.3V ±10%; TA = -40 to 85°C ) Characteristics 1 Pull-in range 2 Min Typ Lock Time Max Units ±1000 ppm 300 Notes At nominal input reference frequency C19i = 19.44 MHz ms Performance Characteristics : Output Jitter Generation - GR-253-CORE GR-253-CORE conformance (VCC = 3.3V ±10%; TA = -40 to 85°C ) ZL30414 ZL30414 Jitter Generation Performance GR-253-CORE GR-253-CORE Jitter Generation Requirements Interface (Category II) 1 2 3 Jitter Measurement Filter OC-48 OC-48 STS-48 STS-48 12 kHz - 20 MHz OC-12 OC-12 STS-12 STS-12 12 kHz - 5 MHz Max 0.1 UIPP 10.0 - 7.31 psP-P 1.0 0.52 0.94 psRMS 0.1 UIPP 40.2 - 7.32 psP-P 0.01 UIRMS 50 kHz - 80 MHz Typ 0.01 UIRMS OC-192 OC-192 STS-192 STS-192 Equivalent limit in time domain 4.02 0.58 0.83 psRMS 0.1 UIPP 161 - 4.37 psP-P 0.01 UIRMS 16.1 0.34 0.60 psRMS Limit in UI Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF 19 Zarlink Semiconductor Inc. Units ZL30414 ZL30414 Data Sheet Performance Characteristics : Output Jitter Generation - G.813 conformance (Option 1 and 2) (VCC = 3.3V ±10%; TA = -40 to 85°C ) ZL30414 ZL30414 Jitter Generation Performance G.813 Jitter Generation Requirements Jitter Measurement Filter Typ Max 10.0 - 6.95 psP-P 0.89 psRMS - 11.5 psP-P 0.82 1.04 psRMS - 6.40 psP-P 0.50 0.68 psRMS - 8.67 psP-P 0.68 1.06 psRMS - 3.33 psP-P 0.26 0.42 psRMS - 19.1 psP-P 1.51 2.88 psRMS - 6.95 psP-P 0.49 0.89 psRMS - 11.5 psP-P 0.82 1.04 psRMS - 7.32 psP-P 0.58 0.83 psRMS - 4.37 psP-P 0.34 Limit in UI Equivalent limit in time domain 0.49 Interface 0.60 psRMS Units Option 1 1 STM-64 STM-64 4 MHz to 80 MHz 20 kHz to 80 MHz 2 STM-16 STM-16 1 MHz to 20 MHz 5 kHz to 20 MHz 3 STM-4 250 kHz to 5 MHz 1 kHz to 5 MHz 0.1 UIpp 0.5 UIpp 50.2 0.1 UIpp 40.2 0.5 UIpp 201 0.1 UIpp 161 0.5 UIpp 804 Option 2 5 STM-64 STM-64 4 MHz to 80 MHz 20 kHz to 80 MHz 6 7 STM-16 STM-16 STM-4 12 kHz - 20 MHz 12 kHz - 5 MHz 0.1 UIpp 10.0 0.3 UIpp 30.1 0.1 UIpp 40.2 0.1 UIpp 161 Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF 20 Zarlink Semiconductor Inc. ZL30414 ZL30414 Data Sheet Performance Characteristics : Output Jitter Generation - ETSI EN 300 462-7-1conformance (VCC = 3.3V ±10%; TA = -40 to 85°C ) ZL30414 ZL30414 Jitter Generation Performance EN 300 462-7-1 Jitter Generation Requirements Jitter Measurement Filter 5 kHz to 20 MHz 2 STM-4 250 kHz to 5 MHz 1 kHz to 5 MHz 40.2 - 6.40 psP-P 0.68 psRMS - 8.67 psP-P 1.06 psRMS - 3.33 psP-P 0.42 psRMS - 19.1 psP-P 1.51 1 MHz to 20 MHz Max 0.26 STM-16 STM-16 Typ 0.68 1 Limit in UI Equivalent limit in time domain 0.50 Interface 2.88 psRMS 0.1 UIpp 0.5UIpp 201 0.1 UIpp 161 0.5 UIpp 804 Typical figures are for design aid only: not guaranteed and not subject to production testing. Loop Filter components: RF=8.2 k, CF=470 nF 21 Zarlink Semiconductor Inc. Units Package Code c Zarlink Semiconductor 2002 All rights reserved. ISSUE ACN DATE APPRD. Previous package codes For more information about all Zarlink products visit our Web Site at www.zarlink.com Information relating to products and services furnished herein by Zarlink Semiconductor Inc. trading as Zarlink Semiconductor or its subsidiaries (collectively "Zarlink") is believed to be reliable. However, Zarlink assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Zarlink or licensed from third parties by Zarlink, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Zarlink, or non-Zarlink furnished goods or services may infringe patents or other intellectual property rights owned by Zarlink. This publication is issued to provide information only and (unless agreed by Zarlink in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Zarlink without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Zarlink's conditions of sale which are available on request. Purchase of Zarlink's I2C components conveys a licence under the Philips I2C Patent rights to use these components in an I2C System, provided that the system conforms to the I2C Standard Specification as defined by Philips. Zarlink, ZL and the Zarlink Semiconductor logo are trademarks of Zarlink Semiconductor Inc. Copyright 2003, Zarlink Semiconductor Inc. All Rights Reserved. TECHNICAL DOCUMENTATION - NOT FOR RESALE